Sony KDL-52W3100 Operating instructions

LCD Digital Colour TV

3-217-216-11(1)

KDL-52W3100

KDL-46W3100

KDL-40W3100

Operating Instructions

Before operating the TV, please read the “Safety

information” section of this manual.

Retain this manual for future reference.

2

GB

Thank you for choosing this Sony product.

Before operating the TV, please read this manual

thoroughly and retain it for future reference.

• is a registered trademark of the DVB Project

• “Dolby” and the double-D symbol are trademarks of

Dolby Laboratories.

Manufactured under license from Dolby Laboratories.

• HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of

HDMI Licensing LLC.

• Adobe is a registered trademark or a trademark of Adobe

Systems Incorporated in the United States and/or other

countries.

The illustrations used in this manual are of the KDL-

40W3100 unless otherwise stated.

Introduction Trademark information

3

GB

Table of Contents

Start-up Guide 4

Safety information .....................................................................................................................9

Precautions .............................................................................................................................10

Overview of the remote ........................................................................................................12

Overview of the TV buttons and indicators ........................................................................13

Watching TV............................................................................................................................14

Using the Favourite List ..................................................................................................17

Connecting optional equipment...............................................................................................18

Viewing pictures from the connected equipment ....................................................................21

Using the remote.....................................................................................................................22

Using HDMI control .................................................................................................................25

Navigating through menus ......................................................................................................26

Picture menu ...........................................................................................................................27

Sound menu............................................................................................................................29

Screen menu (except for PC input).........................................................................................31

Screen menu (for PC input) ....................................................................................................32

Video Settings menu ...............................................................................................................33

Audio Settings menu ...............................................................................................................35

Set-up menu............................................................................................................................36

Analogue Set-up menu ...........................................................................................................39

Digital Set-up menu ........................................................................................................41

Specifications ..........................................................................................................................43

Troubleshooting ......................................................................................................................45

Watching TV

Using Optional Equipment

Using Menu Functions

Additional Information

: for digital channels only

4

GB

Start-up Guide

1: Checking the

accessories

AC power cord* (1)

Antenna cable* (1)

PC cable* (1)

Support belt (1) and screws (2)

Remote RM-GD003 (1)

Size AA batteries (R6 type) (2)

* Do not remove the ferrite cores.

To insert batteries into the remote

~

• Observe the correct polarity when inserting batteries.

• Do not use different types of batteries together or mix old

and new batteries.

• Dispose of batteries in an environmentally friendly way.

Certain regions may regulate the disposal of batteries.

Please consult your local authority.

• Handle the remote with care. Do not drop or step on it, or

spill liquid of any kind onto it.

• Do not place the remote in a location near a heat source, a

place subject to direct sunlight, or a damp room.

2: Connecting an

antenna/VCR

* When connecting an antenna cable, an adaptor (not

supplied) may be required.

Push and slide to open.

Connecting an antenna

Antenna cable*

AC power cord

(supplied)

Factory-installed

antenna cable

5

GB

Start-up Guide

* When connecting an antenna cable, an adaptor (not

supplied) may be required.

3: Preventing the TV

from toppling over

(MONO)

Connecting an antenna and VCR

A/V cable

(not

supplied)

VCR

AC power cord

(supplied)

Antenna cable

(not supplied)

Antenna cable

(not supplied)

Antenna cable

(supplied)*

Splitter

(not supplied)

Factory-

installed

antenna

cable

S video cable

(not supplied)

6

GB

4: Bundling the cables

~

The hook of the cable holder can be opened from either sides

depending on attaching position.

5: Performing the initial

set-up

1 Connect the TV to your AC power outlet

(220–240 V AC, 50 Hz).

2 Press 1 on the top edge of the TV.

When you turn on the TV for the first time, the

Time Setup menu appears on the screen.

Selecting the state/region

3, 4, 5, 8, 10

7, 9

3, 4, 5, 8, 10

7

GB

Start-up Guide

3 Press F/f/G/g to select the state/region

in which you will operate the TV, then press

.

This option allows you to set the time zone in

which you will operate the TV. This will ensure

that the time displayed on the i-Plate (page 16) is

correct.

4 Press F/f to select “Full Scan” or “Quick

Scan” to preset channels, then press .

“Full Scan”: All available channels are tuned and

stored. This procedure may take some time.

“Quick Scan”: All expected channels in your

area are tuned and stored. You will need to select

your nearest city to help speed up this procedure.

5 Press G/g to select “OK”, then press .

A display appears showing a tuning progress bar

and the channels tuned and stored.

The TV starts searching for all available digital

channels, followed by all available analogue

channels. This may take some time, please be

patient and do not press any buttons on the TV or

remote.

If a message appears for you to confirm the

antenna connection

No digital or analogue channels were found.

Check the antenna connection and press G

/

g to

select “Yes”, then press to start auto-tuning

again.

6 When the Programme Sorting menu

appears on the screen, follow the steps of

“Programme Sorting” (page 39).

If you do not change the order in which the

analogue channels are stored on the TV, go to step

7.

7 Press MENU to display the Clock Set

menu.

When digital channels have been stored, set

“Time Adjustment” to “Auto”, then go to step 9.

If no digital channels have been stored, set “Time

Adjustment” to “Manual”, then go to next step.

8 Press F/f/G/g to set the day and time

(hour and minute), then press .

9 Press MENU to exit.

The TV has now tuned in all the available

channels.

10Press G/g to select the desired setting in

“Display this menu next time ?” dialogue,

then press to exit.

z

If “Yes” is selected and the TV is turned off by pressing 1

on the TV, or is disconnected from the AC power outlet, the

auto start-up procedure restarts the next time the TV is turned

on.

Auto-tuning the TV

8

GB

Detaching the Table-

Top Stand from the TV

~

Do not remove the Table-Top Stand for any reason other than

to wall-mount the TV or to set the optional TV stand.

9

GB

Safety information

Installation/Set-up

Install and use the TV set in accordance with the

instructions below in order to avoid any risk of fire,

electrical shock or damage and/or injuries.

Installation

• The TV set should be installed near an easily accessible

AC power outlet.

• Place the TV set on a stable, level surface.

• Only qualified service personnel should carry out wall

installations.

• For safety reasons, it is strongly recommended that you

use Sony accessories, including:

– Wall-mount bracket SU-WL500

– TV stand SU-FL300M (only for KDL-40W3100/KDL-

46W3100)

Transporting

• Before transporting the TV

set, disconnect all cables.

• Two or three people are

needed to transport a large

TV set.

• When transporting the TV

set by hand, hold it as shown

on the right. Do not put

stress on the LCD panel.

• When lifting or moving the

TV set, hold it firmly from

the bottom.

• When transporting the TV

set, do not subject it to jolts

or excessive vibration.

• When transporting the TV

set for repairs or when

moving, pack it using the

original carton and packing

material.

Ventilation

• Never cover the ventilation holes or insert anything in the

cabinet.

• Leave space around the TV set as shown below.

• It is strongly recommended that you use a Sony wall-

mount bracket in order to provide adequate air-circulation.

Installed on the wall

Installed with stand

• To ensure proper ventilation and prevent the collection of

dirt or dust:

– Do not lay the TV set flat, install upside down,

backwards, or sideways.

– Do not place the TV set on a shelf, rug, bed or in a

closet.

– Do not cover the TV set with a cloth, such as curtains,

or items such as newspapers, etc.

– Do not install the TV set as shown below.

AC power cord

Handle the AC power cord and outlet as follows in

order to avoid any risk of fire, electrical shock or

damage and/or injuries:

– Connect the TV set using a three-wire grounding type

AC power plug to a AC power outlet with a protective

earthing connection.

– Use only Sony AC power cords, not those of other

brands.

– Insert the plug fully into the AC power outlet.

– Operate the TV set on a 220–240 V AC supply only.

– When wiring cables, be sure to unplug the AC power

cord for your safety and take care not to catch your feet

on the cables.

– Disconnect the AC power cord from the AC power

outlet before working on or moving the TV set.

– Keep the AC power cord away from heat sources.

– Unplug the AC power plug and clean it regularly. If the

plug is covered with dust and it picks up moisture, its

insulation may deteriorate, which could result in a fire.

Notes

• Do not use the supplied AC power cord on any other

equipment.

• Do not pinch, bend, or twist the AC power cord

excessively. The core conductors may be exposed or

broken.

• Do not modify the AC power cord.

• Do not put anything heavy on the AC power cord.

• Do not pull on the AC power cord itself when

disconnecting the AC power cord.

• Do not connect too many appliances to the same AC

power outlet.

• Do not use a poor fitting AC power outlet.

Be sure to hold the

bottom of the panel,

not the front part.

30 cm

10 cm 10 cm

10 cm

Leave at least this space around the set.

30 cm

10 cm 10 cm 6 cm

Leave at least this space around the set.

Air circulation is blocked.

Wall Wall

Continued

10

GB

Prohibited Usage

Do not install/use the TV set in locations,

environments or situations such as those listed below,

or the TV set may malfunction and cause a fire,

electrical shock, damage and/or injuries.

Location:

Outdoors (in direct sunlight), at the seashore, on a ship or

other vessel, inside a vehicle, in medical institutions,

unstable locations, near water, rain, moisture or smoke.

Environment:

Places that are hot, humid, or excessively dusty; where

insects may enter; where it might be exposed to mechanical

vibration, near flammable objects (candles, etc). The TV

shall not be exposed to dripping or splashing and no objects

filled with liquids, such as vases, shall be placed on the TV.

Situation:

Do not use when your hands are wet, with the cabinet

removed, or with attachments not recommended by the

manufacturer. Disconnect the TV set from AC power outlet

and antenna during lightning storms.

Broken pieces:

• Do not throw anything at the TV set. The screen glass may

break by the impact and cause serious injury.

• If the surface of the TV set cracks, do not touch it until you

have unplugged the AC power cord. Otherwise electric

shock may result.

When not in use

• If you will not be using the TV set for several days, the TV

set should be disconnected from the AC power for

environmental and safety reasons.

• As the TV set is not disconnected from the AC power

when the TV set is just turned off, pull the plug from the

AC power outlet to disconnect the TV set completely.

• However, some TV sets may have features that require the

TV set to be left in standby to work correctly. The

instructions in this manual will inform you if this applies.

For children

• Do not allow children to climb on the TV set.

• Keep small accessories out of the reach of children, so that

they are not mistakenly swallowed.

If the following problems occur...

Turn off the TV set and unplug the AC power cord

immediately if any of the following problems occur.

Ask your dealer or Sony service centre to have it

checked by qualified service personnel.

When:

– AC power cord is damaged.

– Poor fitting of AC power outlet.

– TV set is damaged by being dropped, hit or having

something thrown at it.

– Any liquid or solid object falls through openings in the

cabinet.

Precautions

Viewing the TV

• View the TV in moderate light, as viewing the TV in poor

light or during long period of time, strains your eyes.

• When using headphones, adjust the volume so as to avoid

excessive levels, as hearing damage may result.

LCD Screen

• Although the LCD screen is made with high-precision

technology and 99.99% or more of the pixels are effective,

black dots may appear or bright points of light (red, blue,

or green) may appear constantly on the LCD screen. This

is a structural property of the LCD screen and is not a

malfunction.

• Do not push or scratch the front filter, or place objects on

top of this TV set. The image may be uneven or the LCD

screen may be damaged.

• If this TV set is used in a cold place, a smear may occur in

the picture or the picture may become dark. This does not

indicate a failure. These phenomena disappear as the

temperature rises.

• Ghosting may occur when still pictures are displayed

continuously. It may disappear after a few moments.

• The screen and cabinet get warm when this TV set is in

use. This is not a malfunction.

• The LCD screen contains a small amount of liquid crystal

and mercury. The fluorescent tubes used in this TV set

also contain mercury. Follow your local ordinances and

regulations for disposal.

Handling and cleaning the screen surface/cabinet of

the TV set

Be sure to unplug the AC power cord connected to the TV set

from AC power outlet before cleaning.

To avoid material degradation or screen coating degradation,

observe the following precautions.

• To remove dust from the screen surface/cabinet, wipe

gently with a soft cloth. If dust is persistent, wipe with a

soft cloth slightly moistened with a diluted mild detergent

solution.

• Never use any type of abrasive pad, alkaline/acid cleaner,

scouring powder, or volatile solvent, such as alcohol,

benzene, thinner or insecticide. Using such materials or

maintaining prolonged contact with rubber or vinyl

materials may result in damage to the screen surface and

cabinet material.

• When adjusting the angle of the TV set, move it slowly so

as to prevent the TV set from moving or slipping off from

its table stand.

Optional Equipment

Keep optional components or any equipment emitting

electromagnetic radiation away from the TV set. Otherwise

picture distortion and/or noisy sound may occur.

11

GB

Disposal of Old Electrical & Electronic Equipment

(Applicable in the European Union and other

European countries with separate collection

systems)

This symbol is on the remote control.

12

GB

Overview of the remote

z

The number 5, H, PROG + and A/B

buttons have tactile dots. Use the tactile dots

as references when operating the TV.

1 TV "/1 — TV standby

Turns the TV on and off from standby mode.

2 Number buttons

• In TV mode: Selects channels. For channel numbers 10 and above, enter

the second, third or fourth digit quickly.

• In Text mode: Enters the three digit page number to select the page.

3 — Previous channel

Returns to the previous channel watched (for more than five seconds).

4 — Wide Mode (page 15)

5 — Picture freeze (page 14)

Freezes the TV picture.

6 / — Input select / Text hold

• In TV mode (page 21): Displays the connected equipment list and selects

the input source.

• In Text mode (page 14): Holds the current page.

7 F/f/G/g/ (page26)

8 TOOLS (page 15, 21)

Enables you to access various viewing options and change/make adjustments

according to the source and Wide Mode.

9 MENU (page 26)

0 PROG +/–/ /

• In TV mode (page 14): Selects the next (+) or previous (–) channel.

• In Text mode (page 14): Selects the next ( ) or previous ( ) page.

qa A/B — Dual Sound (page 30)

qs % — Mute (page 14, 21)

qd 2 +/– — Volume (page 21)

qf THEATRE

You can set Theatre Mode on or off. When Theatre Mode is set to on, the

optimum audio output (if the TV is connected with an audio system using an

HDMI cable) and picture quality for film-based contents are automatically set.

z

If you turn the TV off, Theatre Mode is also turned off.

qg RETURN

Returns to the previous screen of any displayed menu.

qh

This button does not work with this model.

qj Coloured buttons (page 14)

qk DIGITAL/ANALOG — TV mode (page 14)

ql — Twin Picture (page 21)/PIP (page 22) (for PC input)

Displays two pictures simultaneously.

w; / — Text (page 14)

wa LIGHT

Lightens the buttons on the remote so that you can control them easily even

if the room is dark.

ws / — Info / Text reveal

• In digital mode (page 16): Displays details of the current or next

programme.

• In analogue mode: Displays information such as current channel number

and Wide Mode.

• In Text mode (page 14): Reveals hidden information (e.g. answers to a quiz).

wd Buttons for using optional equipment

See page 22.

13

GB

Overview of the TV buttons and indicators

1 1 — Power

Turns the TV on or off.

~

To disconnect the TV from the AC power completely,

pull the plug from the AC power outlet.

2 PROG +/–/ /

• In TV mode: Selects the next (+) or previous (–)

channel.

• In TV menu: Moves through the options up ( ) or

down ( ).

3 2 +/–/ /

• In TV mode: Increases (+) or decreases (–) the

volume.

• In TV menu: Moves through the options right ( )

or left ( ).

4 / — Input select / OK

• In TV mode (page 21): Displays the connected

equipment list and selects the input source.

• In TV menu: Selects the menu or option, and

confirms the setting.

5 (page 26)

6 — Picture Off / Timer indicator

• Lights up in green when the picture is switched off

(page 37).

• Lights up in orange when the timer is set

(page 36).

7 1 — Standby indicator

Lights up in red when the TV is in standby mode.

8 " — Power indicator

• Lights up in green when the TV is turned on.

• Flashes while the remote is being operated.

9 Remote control sensor / Light sensor (page 37)

• Receives IR signals from the remote.

• Do not put anything over the sensor, as its function

may be affected.

~

Make sure that the TV is completely turned off before

unplugging the AC power cord. Unplugging the AC power

cord while the TV is turned on may cause the indicator to

remain lit or may cause the TV to malfunction.

14

GB

Watching TV

1 Press 1 on the top edge of the TV to turn

on the TV.

When the TV is in standby mode (the 1 (standby)

indicator on the TV front panel is red), press

TV "/1 on the remote to turn on the TV.

2 Press DIGITAL/ANALOG to switch

between digital and analogue modes.

The channels available vary depending on the

mode.

3 Press the number buttons or PROG +/– to

select a TV channel.

To select channel numbers 10 and above using the

number buttons, enter the second, third or fourth

digits quickly.

In digital mode, an information banner appears

briefly. The following icons may be indicated on

the banner.

In normal TV mode

: SD (or : HD)

RADIO: Radio service

: Parental rating

: Multi audio programme

: Text service

In Twin Picture mode (page 21)

: Radio service

: Parental Lock

Additional operations

To access Text

Press /. Each time you press /, the display changes

cyclically as follows:

Text and TV picture t Text t No Text (exit the

Text service)

To select a page, press the number buttons or / .

To hold a page, press / .

To reveal hidden information, press / .

To jump a page (in analogue mode only), press and

F/f, then press (for three digit pages).

z

When four coloured items appear at the bottom of the Text

page, Fastext is available (in analogue mode only). Fastext

allows you to access pages quickly and easily. Press the

corresponding coloured button to access the page.

Watching TV

2

3

To Press

Freeze the picture

(Picture freeze)

.

Press again to return to normal

TV mode.

~

This function is not available for a

PC input source.

Mute the sound %.

Press again to restore.

Turn on the TV

without sound from

standby mode

%.

15

GB

Watching TV

To change the Wide Mode manually

Press repeatedly to select the desired Wide Mode.

* Parts of the top and bottom of the picture may be cut off.

~

• Some characters and/or letters at the top and the bottom of

the picture may not be visible in “Wide Zoom”. In such a

case, you can select “Vertical Size” using the “Screen”

menu and adjust vertical size to make it visible.

• Wide Mode is fixed to “Full” in digital mode.

z

• When “Auto Wide” is set to “On”, the TV will

automatically select the best mode to suit the input from an

external equipment (page 31).

• You can adjust the position of the picture when selecting

“Wide Zoom” or “Zoom”. Press

F/f to move up or down

(e.g. to read subtitles).

• Select “Wide Zoom” or “Zoom” to adjust for 720p, 1080i

or 1080p source pictures with edge portions cut off.

• “Full 1”, “Full 2” and “Normal” are available for “Wide

Mode” when PC input is selected (page 32).

Using the Tools menu

Press TOOLS to display the following options when

viewing a TV programme.

To view two pictures simultaneously – PIP

(Picture in Picture) (in digital mode only)

This feature allows you to view a different sub-

channel in a window and also access multiview

services (when available from broadcaster, e.g.

different camera angles).

1 Press TOOLS to display the Tools menu.

2 Press F/f to select “PIP Programme List”,

then press

.

3 Press F/f to select the required channel/

multiview service, then press .

To return to normal TV mode

Select “PIP Programme List” from the Tools

menu. Then, select “Close PIP”.

~

Depending on the broadcast signal, the image displayed on

the PIP sub screen may be smaller than its frame size.

Wide Zoom*

Enlarges the centre

portion of the picture.

The left and right

edges of the picture are

stretched to fill the

16:9 screen.

Normal

Displays the 4:3

picture in its original

size. Side bars are

shown to fill the 16:9

screen.

Full

Stretches the 4:3

picture horizontally,

to fill the 16:9 screen.

Zoom*

Displays

cinemascopic (letter

box format)

broadcasts in the

correct proportions.

Options Description

Close Closes the Tools menu.

Picture Mode See page 27.

Sound Mode See page 29.

Speaker See page 35.

Twin Picture See page 21.

Favourite List (in

digital mode only)

See page 17.

PIP Programme List (in

digital mode only)

See page 15.

i Volume See page 35.

Sleep Timer See page 36.

Power Saving See page 37.

Continued

16

GB

i-Plate display

For a single picture in digital mode, this feature gives

you information on the current channel and also the

current and next programmes.

1 Press / to display the i-Plate.

This shows the date, time, whether the channel has

text service, whether multi (MPEG and Dolby

Digital) audio programme available and whether the

picture is available in high definition or standard

definition (HD or SD is displayed).

2 Press / to display information on the

following programme.

3 Press / again (or MENU) to turn off the

i-Plate display and return to normal

operation.

The following icons may be displayed on the i-Plate

display according to the programme.

: SD (or : HD)

: Parental rating

: Multi audio programme

: Text service

z

The code coming after MPEG determines the language type.

For detail, refer to “i-Plate Display Language Code” on

page 44.

17

GB

Watching TV

Using the Favourite List *

The Favourite feature allows you to select

programmes from a list you specify. To display the

Favourite List, see “Navigating through menus”

(page 26).

* This function may not be available in some areas.

Favourite List

To Do this

Create your Favourite List Follow the steps of “Favourite Preset” (page 42) in Digital Set-up menu.

Watch a Favourite channel

1 Press MENU to display the menu (page 26).

2 Press

F/f to select “Digital Favourites List”, then press .

3 Press

G/g to select “Favourite List 1” or “Favourite List 2”.

4 Press

F/f to select your favourite channel.

5 Press to exit the Favourite List and display the selected

channel.

z

Once you select a channel within your Favourite List of channels, pressing PROG

+/– will select only channels from your Favourite List. To select a channel that has

not been programmed as a Favourite List channel, use the Programme List feature

or the number buttons.

Turn off the Favourite list Press MENU.

18

GB

Connecting optional equipment

You can connect a wide range of optional equipment to your TV.

Using Optional Equipment

Camcorder

Headphones

PC (HDMI output) Camcorder

Audio system

DVD playerBlu-ray disc player

19

GB

Using Optional Equipment

(MONO)

Audio system Blu-ray disc

player

CamcorderDVD player

For service use

only

DVD player with component output

Hi-Fi audio equipment

DVD recorder

VCR

PC

Video game equipment

DVD player

VCR

Home theatre system

with digital input

PC (HDMI

output)

Continued

20

GB

Connect to Input symbol on

screen

Description

A i You can listen to sound from the TV on headphones.

B 2 or 2, and

2

Video 2 or

Video 2

To avoid picture noise, do not connect the camcorder to the

video 2 jack and the S video 2 jack at the same time. If

you connect mono equipment, connect to the 2 L jack.

C HDMI IN 2

D HDMI IN 1 or 3

HDMI 2

HDMI 1 or

HDMI 3

The digital video and audio signals are input from the

equipment.

In addition, when HDMI control compatible equipment is

connected, communication with the connected equipment is

supported. Refer to page 37 to set up this communication.

If the equipment has a DVI jack, connect the DVI jack to the

HDMI IN 1 jack through a DVI - HDMI adaptor interface (not

supplied), and connect the equipment’s audio out jacks to the

audio in jacks in the HDMI IN 1 jacks.

~

• The HDMI jacks only support the following video inputs: 480i,

480p, 576i, 576p, 720p, 1080i, 1080p and 1080/24p. For PC

video inputs, see page 44.

• Be sure to use only an HDMI cable that bears the HDMI logo.

• When connecting an HDMI control compatible audio system, be

sure to also connect to the DIGITAL OUT (OPTICAL) jack.

E PC IN (RGB)/ PC It is recommended to use a supplied PC cable with ferrite cores.

F 1 or 1 or 3,

and 1 or 3

Video 1 or

Video 3

To avoid picture noise, do not connect the camcorder to the

video jack 1 and the S video jack 1 at the same time. If

you connect mono equipment, connect to the L(MONO) jack

1 or 3.

G / Use to record the analogue video and sound from the TV to a

DVD recorder or VCR. To turn off the sound of the TV

speakers, set “Speaker” to “Audio System” (page 35). If you

connect mono equipment, connect to the L jack .

~

• The monitor output jacks cannot support HD/DVD, HDMI and

PC signals source pictures, also digital audio signal for sound.

• The images of digital broadcasting recorded on this TV appear

enlarged when they are played on a 4:3 screen size TV that cannot

be adjusted to other aspect modes.

H / 1 or 2 HD/DVD 1 or

HD/DVD 2

For better picture quality, component connection is

recommended if your DVD player has a component video

output.

I You can listen to the sound from the TV on Hi-Fi audio

equipment.

J DIGITAL OUT

(OPTICAL)

Use the Optical audio cable.

Page is loading ...

Sony KDL-52W3100 Operating instructions

This manual is also suitable for

Sony KDL-52W3100 Operating instructions

Related papers

Other documents