Creative LabelTac 4 PRO Quick start guide

Brand: Creative

Model: LabelTac 4 PRO

Category: Label printers

Type: Quick start guide

QUICK START GUIDE

IMPORTANT:

Please read this manual carefully.

Use this manual when you need quick reference help for the printer.

LABELTAC 4 PRO

THERMAL TRANSFER PRINTER

CREATIVE SAFETY SUPPLY

(866) 777-1360

www.creativesafetysupply.com

PACKING LIST

Check to ensure that you receive these items:

a) LabelTac 4 PRO Thermal Transfer Printer

b) USB Transfer Cable

c) Power Cable

d) Software/Driver Install CD

e) This Quickstart Manual

GETTING STARTED

Here are the main components of your LabelTac 4 PRO printer.

Cover support

release

Used ribbon rewind

spool/hub

Ribbon supply spool/

hub

Media holder

Platen roller

Alignment

guides

Black mark

sensor

Power switch

(on rear)

USB interface port

(on rear)

Left cover

release

Ribbon access

cover

Right cover

release

LED indicator

Feed button

Printhead

A) OPENING/CLOSING THE TOP COVER

B) LOADING PRINT RIBBON (Video available on LabelTac 4 Install Disc)

1) To open cover, pull both

blue cover release tabs

straight towards you. Lift

cover.

1) Open cover using both

blue cover release tabs.

Open ribbon access cover

by pressing on the indent.

4) Pull ribbon (dull side

down) up and over the print-

head. Insert the carboard

core into the rewind spool.

2) The cover support will

engage to hold the cover

open.

2) Remove ribbon sup-

ply and rewind spools and

insert ribbon into the supply

spool.

5) Insert rewind spool into

the rewind hub (front), and

tape the ribbon to the the

cardboard core lengthwise.

3) To close cover, lift cover

support from rear, pull to-

wards you, and close cover

gently.

3) Insert supply spool into

the supply hub (rear), left

side rst, and snap into

place.

6) Close the ribbon access

cover, disengage the cover

support and gently close the

top cover.

C) LOADING MEDIA SUPPLY (Video available on LabelTac 4 Install Disc)

1) Open cover using both

blue cover release tabs.

4) Feed the supply through

the alignment guides and

out through the mouth of

the printer.

2) Remove blue media

holder and place media on

holder, closing each end

with the arm cap.

5) Adjust the blue alignment

guides manually to t the

width of the media

3) Replace media holder,

ensuring the media can turn

freely.

6) Disengage the cover

support and gently close the

top cover.

INSTALLING PRINTER DRIVERS (Windows Only)

1) Insert the LabelTac 4 PRO Install Disc. The disc will autorun and pop up the Install

Menu. Select “Install LabelTac Drivers” from the menu options. Depending on your

account settings, a popup box may appear asking if you want to allow the software to

make changes to your computer- Select “Yes” and continue.

2) Select “Install printer drivers” and click Next.

INSTALLING PRINTER DRIVERS (continued)

3) By default, “Install a driver for a Plug and Play printer” is selected. The LabelTac 4

(TSC TTP-343C) should be the only printer in this list. Click the next button.

4) Rename the printer from “TSC_TTP-343C” to “LabelTac4” for easy reference. Click

Next to continue.

INSTALLING PRINTER DRIVERS (continued)

5) Click Finish to complete the installation.

6) If the dialog box above pops up, select “Install this driver software anyways” to

continue.

INSTALLING PRINTER DRIVERS (continued)

7) The LabelTac 4 PRO drivers will now install.

8) When the drivers are nished installing, select Close to continue.

1) Select “Install Templates and Symbols” to begin the installation process.

2) Choose the folder you would like to install the templates and symbols to. The default

is the currently logged-in user’s desktop. We recommend installing the folder to the

desktop for easy access. To select a different location, click browse, and select the

destination folder. When you are done, click “Install” to begin installation.

INSTALLING TEMPLATES & SYMBOLS

INSTALLING PRINTER DRIVERS (continued)

3) When installation is complete, click the Close button to nish installation.

4) The Templates and Symbols will install to a folder called “LabelTac 4 Templates” and

are broken into folders based on the width of the label stock they are to be printed on.

There is also a folder for OpenOfce templates, and another for Symbols and Images.

LED AND BUTTON FUNCTIONS

LED Color Description

Green (Solid)

This illuminates that the power is on and the device is ready to

use

Green (Flash)

This illuminates that the system is downloading data from the

PC to memory, or that the printer is paused

Amber

This illuminates that the system is clearing data from the printer

Red (Solid)

This illuminates printer head open or a cutter error

Red (Flashing)

This illuminates a printing error, such as head open, paper jam,

ribbon empty, or memory error

Power-On Utility Functions

Release button during the following ashing pattern:

Amber

Red

(5 Blinks)

Amber

(5 Blinks)

Green

(5 Blinks)

Green/

Amber

(5 Blinks)

Red/

Amber

(5 Blinks)

1) Ribbon sensor calibration and

Gap/Black Mark sensor calibration

release

2) Gap/Black Mark sensor calibra-

tion + self test and enter dump

mode

release

3) Printer Initialization

release

4) Set Black Mark sensor as media

sensor and calibrate the Black Mark

sensor

release

5) Set Gap sensor as Media Sensor

and calibrate the Gap sensor

release

BUTTON FUNCTIONS:

a) While powered on & not printing: Feeds material (equal size to the last label printed)

b) While printing: Pauses the current print job. Pressing again will resume.

c) While the printer is powered off- if the button is held, and released during different

LED cycles, the printer will perform different functions as detailed in the chart below.

The LabelTac 4 PRO has one button and one 3-color LED indicator. By indicating the

LED with different color and pressing the button, the printer can perform several func-

tions, including feed labels, pause printing, selecting and claibrating the medai sensor,

resetting the printer, and more. Please refer to the button operation and LED function

charts below.

Please call us at (866) 777-1360 with any questions regarding Black Mark, Gap Sen-

sor, or any other Power-On utilities.

TROUBLESHOOTING

• POOR PRINT QUALITY

If you are having issues with poor print quality from your LabelTac 4 PRO printer, do

not hesitate to give us a call at (866) 777-1360, and one of our support representatives

would be glad to help get your printer functioning optimally.

Typically poor print quality is resolved by adjusting the print speed and/or density (la-

beled as “darkness”) in the printing preferences, and/or setting the “print orientation”.

You can reach these screens by going to:

Start -> Devices and Printers -> LabelTac 4 -> Printing Preferences -> Page Setup/Options

We nd the following settings work best with the LabelTac 4 PRO Printer

a) In Page Setup, under orientation, select Landscape 180. This will just change the

direction that the printhead will print the label. This will not chage the format of your

printed label (portrait/landscape). This generally gives the best search results.

*Important*

b) & c) If you are getting speckles or inconsistent printing (g.1), try lowering the print

speed, and/or adjusting the density (darkness). We nd that a setting of 2.00 in/sec

and print density of 6 or 7 produces the best results. If you get arched heat lines in

your print (g.2), this means the print ribbon is getting too hot- in this case, try lowering

the density (darkness) and/or raising the print speed.

(g.1) (g.2)

• CONTINUOUS/DIE-CUT LABELS

TROUBLESHOOTING (continued)

When using Die-Cut labels, you must change the settings of the printer so that the

gap sensor detects the die-cut material. If you do not do this, the print will not correctly

align.

There are 2 steps involved with this.

1) Go to the “Stock” tab in the Printing Preferences screen. You can reach this at:

Start -> Devices and Printers -> LabelTac 4 -> Printing Preferences -> Stock

In this screen you will nd an area called “Media Settings”. If you have been printing on

continuous vinyl, the “Type” should be set to “Continuous”. Change this to “Labels with

Gaps”. Leave the other settings as is.

2) Turn off the LabelTac 4 PRO printer. Load the die-cut supply in the printer. Hold the

top button down, and while holding it down, turn the printer back on. The LED will blink

amber once, blink green once, and then begin ashing red rapidly 5 times. Release

the button during the red blinking. The printer will feed out some of the die-cut material

as the gaps/black marks are sensed. You should now be ready to print on the die-cut

material.

When switching back to continuous vinyl, turn the printer off, load the vinyl supply in

the LabelTac 4 PRO and hold down the top button. While holding down the button, turn

the printer back on and release when the printer begins ashing green rapidly. (This

will be after the red blink cycle and amber blink cycle). The printer will feed material,

but will not cut after this intial feed, or if you press the feed button. This is normal.

Once you send a print job to the printer it will resume its normal cutting function.

CREATIVE SAFETY SUPPLY

(866) 777-1360

www.creativesafetysupply.com

QUESTIONS?

Creative LabelTac 4 PRO Quick start guide

Brand: Creative

Model: LabelTac 4 PRO

Category: Label printers

Type: Quick start guide

Download PDF

report

Creative LabelTac 4 PRO Quick start guide

Creative LabelTac 4 PRO Quick start guide

Other documents