Sony RM-VZ220 User manual
- Category
- Portable DVD/Blu-Ray players
- Type
- User manual
4-170-642-12(1)
Remote Commander
RM-VZ220
©2010 Sony Corporation Printed in China
Operating Instructions
Manual de instrucciones (parte posterior)
English
For the Customers in the U.S.A.
WARNING
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this
manual could void your authority to operate this equipment.
Setting Up the RM-VZ220
The RM-VZ220 is preset at the factory to operate Sony brand video devices
set to any of the Device Select buttons (see the table below).
To use with non-Sony devices, or Sony devices that are not preset at the
factory, set the manufacturer’s code for each device.
Devices Button Factory setting*
TV
TV
Sony TV (00810)
TV, Cable set top box, Satellite
receiver, IPTV, DVD player, DVD
recorder, Blu-ray Disc player, DVR
(digital video recorder), PVR
(personal video recorder), VCR,
DVD Home Theater
CBL (SAT)
Cable set top box (non-
Sony) (51376)
VCR
Sony VCR (60032)
DVD
Sony DVD player
(11033)
* The five-digit code is the preset manufacturer’s code.
Note
Only a TV can be assigned to the TV Device Select button. You can assign any device to
the other Device Select buttons.
Installing the batteries
Slide open the battery compartment and insert two size AA (R6) dry
batteries (not supplied).
Insert the batteries (negative end first) through the guide clamp within each
compartment as shown below.
1 2
Battery life
Under normal conditions, size AA (LR6) alkaline batteries will last up to one
year. If the RM-VZ220 does not operate properly, the batteries might be
drained. Replace both batteries with new ones.
Notes
Replace the batteries within 2 minutes after removing them, and do not press any
button when replacing the batteries. Otherwise, your code settings may be cleared.
Do not use an old battery with a new one, or mix different types of batteries together.
If the electrolyte inside the battery should leak, wipe the contaminated area of the
battery compartment with a cloth and replace the old batteries with new ones. To
prevent electrolyte from leaking, remove the batteries when you plan not to use the
RM-VZ220 for a long period of time.
Specifications
Operating distance Approx. 11 m (36 ft) (varies depending on devices of
different manufacturers)
Power requirements
Two size AA (R6) dry batteries (not supplied)
Battery life
Approx. 1 year when using size AA (LR6) alkaline batteries
(varies depending on frequency of button use - up to approx.
300 times per day.)
Dimensions
Approx. 53 × 213 × 27 mm (2
1
/
8
× 8
1
/
2
× 1
1
/
8
in.)
(w/h/d)
Mass
Approx. 100 g (3.5 oz) (not including batteries)
Design and specifications are subject to change without notice.
Troubleshooting
If you have problems setting up or using the RM-VZ220:
Carefully perform the setup procedure of “Startup Guide.” If the RM-VZ220 does not
work, try repeating the setup procedure using another manufacturer’s code (if listed
for your device). If you still cannot operate the RM-VZ220, try the Search function
(see “Searching for the correct code”).
Aim the RM-VZ220 directly at the device.
Remove any obstacles in the path between the RM-VZ220 and the device.
Make sure you have pressed the correct Device Select button.
Check that the device has infrared remote capability. For example, if your device did
not come with a remote control, it probably is not capable of being controlled by the
RM-VZ220.
The batteries are weak, or not inserted correctly. Replace them with new ones or insert
them correctly.
For the customers in the U.S.A.
Customer Support Information
After you have read through this manual, if you still cannot get the RM-VZ220 to work
properly, call the Sony Customer Support Helpline at
1-800-822-2217.
Startup Guide
This guide shows you how to set up and use the RM-VZ220 to operate your devices.
If your Sony device has already been preset, see “Operate the device.”
Set the manufacturer’s code
Example: To set up a Philips TV
1
Find the manufacturer’s code in “Manufacturer’s Code List.”
RM-VZ220_U [US,ES] 4-170-642-12(1)RM-VZ220_U [US,ES] 4-170-642-12(1)
4-170-642-12(1)
Remote Commander
RM-VZ220
©2010 Sony Corporation Printed in China
Operating Instructions
Manual de instrucciones (parte posterior)
English
For the Customers in the U.S.A.
WARNING
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
ˎ
Reorient or relocate the receiving antenna.
ˎ
Increase the separation between the equipment and receiver.
ˎ
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
ˎ
Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this
manual could void your authority to operate this equipment.
Setting Up the RM-VZ220
The RM-VZ220 is preset at the factory to operate Sony brand video devices
set to any of the Device Select buttons (see the table below).
To use with non-Sony devices, or Sony devices that are not preset at the
factory, set the manufacturer’s code for each device.
Devices Button Factory setting*
TV
TV
Sony TV (00810)
TV, Cable set top box, Satellite
receiver, IPTV, DVD player, DVD
recorder, Blu-ray Disc player, DVR
(digital video recorder), PVR
(personal video recorder), VCR,
DVD Home Theater
CBL (SAT)
Cable set top box (non-
Sony) (51376)
VCR
Sony VCR (60032)
DVD
Sony DVD player
(11033)
* The five-digit code is the preset manufacturer’s code.
Note
Only a TV can be assigned to the TV Device Select button. You can assign any device to
the other Device Select buttons.
Installing the batteries
Slide open the battery compartment and insert two size AA (R6) dry
batteries (not supplied).
Insert the batteries (negative end first) through the guide clamp within each
compartment as shown below.
1 2
Battery life
Under normal conditions, size AA (LR6) alkaline batteries will last up to one
year. If the RM-VZ220 does not operate properly, the batteries might be
drained. Replace both batteries with new ones.
Notes
ˎ
Replace the batteries within 2 minutes after removing them, and do not press any
button when replacing the batteries. Otherwise, your code settings may be cleared.
ˎ
Do not use an old battery with a new one, or mix different types of batteries together.
ˎ
If the electrolyte inside the battery should leak, wipe the contaminated area of the
battery compartment with a cloth and replace the old batteries with new ones. To
prevent electrolyte from leaking, remove the batteries when you plan not to use the
RM-VZ220 for a long period of time.
Specifications
Operating distance Approx. 11 m (36 ft) (varies depending on devices of
different manufacturers)
Power requirements Two size AA (R6) dry batteries (not supplied)
Battery life Approx. 1 year when using size AA (LR6) alkaline batteries
(varies depending on frequency of button use - up to approx.
300 times per day.)
Dimensions Approx. 53 × 213 × 27 mm (2
1
/
8
× 8
1
/
2
× 1
1
/
8
in.)
(w/h/d)
Mass Approx. 100 g (3.5 oz) (not including batteries)
Design and specifications are subject to change without notice.
Troubleshooting
If you have problems setting up or using the RM-VZ220:
ˎ
Carefully perform the setup procedure of “Startup Guide.” If the RM-VZ220 does not
work, try repeating the setup procedure using another manufacturer’s code (if listed
for your device). If you still cannot operate the RM-VZ220, try the Search function
(see “Searching for the correct code”).
ˎ
Aim the RM-VZ220 directly at the device.
ˎ
Remove any obstacles in the path between the RM-VZ220 and the device.
ˎ
Make sure you have pressed the correct Device Select button.
ˎ
Check that the device has infrared remote capability. For example, if your device did
not come with a remote control, it probably is not capable of being controlled by the
RM-VZ220.
ˎ
The batteries are weak, or not inserted correctly. Replace them with new ones or insert
them correctly.
For the customers in the U.S.A.
Customer Support Information
After you have read through this manual, if you still cannot get the RM-VZ220 to work
properly, call the Sony Customer Support Helpline at
1-800-822-2217.
Startup Guide
This guide shows you how to set up and use the RM-VZ220 to operate your devices.
If your Sony device has already been preset, see “Operate the device.”
Set the manufacturer’s code
Example: To set up a Philips TV
1
Find the manufacturer’s code in “Manufacturer’s Code List.”
Manufacturer’s Code List /
Lista de códigos del fabricante
English
The following tables show brand names (Brand) and their corresponding
code numbers (Code No.).
1Press and hold SET for more than 3 seconds.
TheSET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2Enter the manufacturer’s code.
TheSET indicator flashes three times and turns off.
Español
La siguiente tabla muestra los nombres de las marcas (Brand) y el número
de código correspondiente (Code No.).
1Presione y mantenga presionado el botón SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras tiene presionado el botón SET, presione el botón de selección de
dispositivo deseado y luego suelte ambos botones.
2Ingrese el código del fabricante.
El indicador SET parpadeará tres veces y se apagará.
Brand Code No.
Sony 00810, 00000
Acer 01339
Action 00650
Admiral 00463
Akai 00812, 01675, 00702, 02232
Akira 01733
AOC 01365, 01589
Apex Digital 00748
Aventura 00171
Bell & Howell 00154
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Dynex 01463, 01810, 02049
Electroband 00000
Electrograph 01755
Electrohome 00463
Elektra 01661
Element 01687
Emerson 01864, 00154, 00463, 00171,
01661, 01394
Emprex 01765
Envision 01365, 01589
ESA 00812, 00171
Fisher 00154
Funai 00171
Gateway 01755, 01756
GE 01447, 00051, 02359
GFM 00171
Haier 01748, 01749, 02309, 02449
Harman/Kardon00054
Hisense 00748, 01314, 02098
Hitachi 01643, 02215, 02433
iLo 01684
Infinity 00054
Insignia 01564, 00171, 02049
JBL 00054
JCB 00000
JVC 00731, 01253, 01601, 01774
KDS 01687
Kolin 01331
LG 01423, 02358
LXI 00054, 00154, 00156
MAG 01687
Magnavox 01454, 01866, 00054, 01254,
01365, 02372
Marantz 00054
Matsushita 00650
Maxent 01755
Memorex 00154, 00463, 00150
MGA 00150
Brand Code No.
Midland 00051
Mitsubishi 01250, 00150, 00836
NAD 00156
NEC 01797
NetTV 01755
Norcent 00748, 01365, 01589
Olevia 01610, 01144, 01331
Onida 01253, 02396
Optimus 00154, 00650
Orion 00463, 01463
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
Quasar 00051, 00650
RadioShack 00154
RCA 01447, 01781, 02187, 02247,
02403, 02429, 02434
Realistic 00154
Sampo 01755
Samsung 00812, 00702
Sansui 00463
Sanyo 00154, 01142
Sceptre 01360, 01599
Scott 01711
Sears 00054, 00154, 00156, 00171
Sharp 00818
Spectroniq 01687
Squareview 00171
Superscan 00864
Supreme 00000
SVA 00748
Sylvania 01864, 00054, 00171, 01314,
01394
Symphonic 00171
Syntax 01610, 01144, 01331
Tatung 01756
TCL 02403, 02429
Technics 00051
Techwood 00051
Teknika 00054, 00150
Telefunken 00702
Toshiba 01524, 00154, 00156, 00650
TVS 00463
Venturer 01865
Videocon 01540, 01541, 02436
Vidikron 00054
Viewsonic 01755, 00864, 00885, 01627,
01742
Viore 01684, 02104, 02352
Vizio 01758, 00864, 00885, 01756
VU 02098
TV / TV
Brand Code No.
Wards 00054
Waycon 00156
Westinghouse 01712, 00885, 01577
White
Westinghouse
00463, 01661
Wyse 01365
Zenith 00463, 01661
Brand Code No.
Sony 11633, 10533, 10864, 11033,
11070, 11431, 11516
Accurian 10675
Akai 10695
Allegro 10869
Apex Digital 10672, 11056
Bel Canto Design11571
Broksonic 10695
CineVision 10869
Citizen 10695
CyberHome 11024
Daewoo 10869
Denon 10490, 11634, 12258
Disney 10675, 11270
Emerson 10591, 10675
Enterprise 10591
Funai 10675
GE 10522
GFM 10675
Go Video 10744, 10741, 10869, 11044,
11075
GoldStar 10741
Harman/Kardon11229
Hitachi 10573, 10664
Hiteker 10672
Insignia 10675, 12428, 12596
Integra 11769, 10627, 12147
JVC 10623, 10867, 11164
Kenwood 10490
LG 10591, 10741, 10869
Magnavox 10503, 10539, 10646, 10675,
11354
Marantz 10539, 12414, 12432
Memorex 10695, 11270, 12213
Microsoft 10522, 12083
Mitsubishi 11521
NAD 10741, 12572
Olevia 12331
Brand Code No.
Onkyo 10503, 11769, 10627, 11627,
12147
Oppo 10575, 12545
Panasonic 10490, 11579, 11641
Philco 10675
Philips 10503, 10539, 12056, 12084,
10646, 10675, 11267, 11354,
12434
Pioneer 10142, 10631, 11571, 12442
Polk Audio 10539
Presidian 10675
Proscan 10522
RCA 10522, 11769, 10822, 12213,
12587, 12592, 12594
Rio 10869
Rotel 10623
Samsung 10490, 10573, 10199, 11044,
11075, 12329, 12489
Sansui 10695
Sanyo 10695
Sharp 10630, 10675, 12250
Shinsonic 10533
Sonic Blue 10869
Sylvania 10675
Symphonic 10675
TCL 12587
Technics 10490
Tivo 11503
Toshiba 10503, 11769, 10695, 11154,
11503, 12006, 12277
Urban Concepts 10503
Viore 12553
Vizio 12563
Vtrek 12587
Xbox 10522, 12083
Yamaha 10490, 10539, 10497, 10817,
12298
Zenith 10503, 10591, 10741, 10869
DVD player / Reproductor de DVD
Brand Code No.
Sony 11033, 11070, 11431
Accurian 10675
Apex Digital 11056
Funai 10675
Go Video 10741
JVC 11164
LG 10741
Magnavox 10646, 10675
Panasonic 10490, 11579
Brand Code No.
Philips 10646
Pioneer 10631
RCA 10522
Samsung 10490
Sharp 10675
Sylvania 10675
Toshiba 12277
Zenith 10741
DVD recorder / Grabadora de DVD
Blu-ray Disc/HD-DVD player/
Reproductor de Blu-ray Disc/HD-DVD
Brand Code No.
Sony 11516
Denon 12258
Insignia 10675, 12428, 12596
Integra 11769, 12147
LG 10741
Magnavox 10675
Marantz 12414, 12432
Microsoft 12083
NAD 12572
Olevia 12331
Onkyo 11769, 12147
Oppo 12545
Brand Code No.
Panasonic 11641
Philips 12084, 12434
Pioneer 10142, 12442
RCA 11769
Samsung 10199
Sharp 12250
Sylvania 10675
Toshiba 11769
Viore 12553
Vizio 12563
Xbox 12083
Yamaha 12298
Brand Code No.
Sony 00810, 00000
Acer 01339
Action 00650
Brand Code No.
Midland 00051
Mitsubishi 01250, 00150, 00836
NAD 00156
TV / TV
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
If your device is not listed, try the Search function (see “Searching for the correct code”).
2
Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
the desired Device Select button,
then release both buttons.
3
Enter the manufacturer’s code (01454).
The SET indicator flashes three times and
turns off.
Operate the device
1
Aim the RM-VZ220 directly at the device.
2
Press the Device Select button for the
device you want to operate.
3
Press POWER to turn on the device.
4
Press buttons on the RM-VZ220 to check that they function.
See “Remote Button Descriptions” for the functions of buttons for each device.
If the RM-VZ220 does not seem to be working…
ˎ
Check that you have set the correct manufacturer’s code.
ˎ
Try repeating the setup procedure using another manufacturer’s code (if listed for your device).
If you still cannot operate the RM-VZ220 after trying all the listed codes, try the Search function (see “Searching
for the correct code”).
Notes
ˎ
If the setting is incomplete,
the SET indicator flashes once
and the indicators turn off.
Start again from the
beginning.
ˎ
If no operations are
performed for 10 seconds
while setting, the setting will
be canceled, and must be
restarted.
ˎ
To cancel the process, press
SET any time. The SET
indicator turns off.
SET
POWER
Device
Select
buttons
Number
buttons
The SET indicator
lights up.
Searching for the correct code
You can set the manufacturer’s code using the Search function.
1 Power on the device with its power switch.
2 Aim the RM-VZ220 at the device you want to set.
3 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
4 Enter 9 - 2 - 2 using the number buttons.
The SET indicator flashes three times.
5 Press and hold à to start searching.
When the device turns off, release the button.
If you overshoot the required code, you can search for the next or previous
code using the
ß
or
ù
button.
6 Press .
The SET indicator flashes three times and turns off.
7 Check if the code number works correctly (see “Remote Button
Descriptions”).
If you still cannot operate the device, repeat steps to search for another
code that works for most functions of your device.
Checking the manufacturer’s code you have set
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2 Enter 9 - 3 - 3 using the number buttons.
The SET indicator flashes three times.
3 Press à.
4 When the SET indicator starts flashing, count the number of flashes.
Short flash(es) indicate which digit (first, second, etc.), followed by long
flash(es) to indicate the digit number (i.e., 2 long flashes represent the
number 2). “0” is indicated by rapid flashing.
Determine the 5-digit code number this way. To recheck, press à.
5 Press SET to finish.
Clearing the automatic power-on control (Sony
devices only)
The Device Select buttons are preset to automatically turn on a device when
pressed.
To cancel the function:
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
, then release both buttons.
2 Enter 9 - 7 - 7 using the number buttons.
The SET indicator flashes three times.
3 Press the desired Device Select button.
The SET indicator flashes three times and turns off.
To set the function again, perform the same procedure above.
Restoring the factory settings
You can clear all the settings and reset the RM-VZ220 to its factory settings.
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press , then release both buttons.
2 Enter 9 - 0 - 0 using the number buttons.
The SET indicator flashes three times.
To cancel, press any button except .
3 Press
.
The SET indicator flashes three times and turns off.
Remote Button Descriptions
General
ȩȪ
SET: Press to set up the RM-VZ220. The indicator lights or flashes while
setting.
ȫ
Device Select buttons: Press to select the device to operate.
Ȯ
GUIDE: Displays the program guide (EPG).
ȯ
j//V/p/
: Moves the cursor to select a menu item/enters the selected item.
ȱ
RETURN: Returns to the previous display/exits the menu.
ȳ
VOL +/–: Turns the volume up/down.
ȸ
POWER: Turns the selected device on and off.
Ⱦ
MUTING: Mutes the volume. Press again to turn muting off.
ɀ
SLEEP: Enables the Sleep function (when available).
The number 5,CH+, and à buttons each have a tactile dot for ease of use.
TheGUIDE and RETURN buttons do not work for a VCR.
Note on the VOL+/– and MUTING buttons
When a TV or other video device is selected, the TV’s volume is controlled. When a
DVD Home Theater is selected, its volume can be controlled.
TV
Ȭ
Ã
: VIDEO 1 input
: VIDEO 2 input
: HDMI input
Ñ
: RGB input
ù
: (PIP INPUT) Changes the
input mode of the “window”
picture.
à
: (PIP) Turns the “window”
picture on and off.
ß
: (PIP MOVE) Moves the
location of the “window” picture.
ê
: (PIP STILL) Freezes the
“window” picture.
Ą
: (PIP SWAP) Switches between
“main” and “window” picture.
ȭ
A: Red button
B: Green button
C: Yellow button
D: Blue button
Ȱ
LIST: (CAPTION) Displays closed
captioning.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵȶɁ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: (PIP CH +/–) Changes
the channel up/down in the
“window” picture.
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: Selects the channel
previously selected.
ȿ
CH +/–: Switches the channel up/
down.
Cable set top box/IPTV
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A, B, C buttons
D: (Live TV) Displays Master
Guide.
Ȱ
LIST: Displays the title of recorded
program.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵȶ Ɂ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: Page up/down
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: Switches between the
current and previous channel.
ȿ
CH +/–: Switches the channel up/
down.
Satellite receiver
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: Red button
B: Green button
C: Yellow button
D: Blue button
Ȱ
LIST: Displays the title of recorded
program/PVR menu.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: (TV/SAT) Switches the
output between SAT and TV.
ȵȶ Ɂ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: Page up/down
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the Satellite
dish menu/Station Index.
Ƚ
RECALL: Tunes to the last tuned
station.
ȿ
CH +/–: Switches the channel up/
down.
VCR
Ȭ
ù
: Rewinds.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȷ
ì: Ejects a tape.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: (ANT/SW) Switches
the antenna output.
Ƚ
RECALL: (DRIVE SELECT) Selects
the deck.
ȿ
CH +/–: Switches the channel up/
down.
Ɂ
ENTER: Enters the selected item.
DVD player/recorder
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records (for DVD recorder).
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȱ
LIST: Displays the Title List.
Ȳ
MENU: Displays the DVD menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +: (DVD) Selects the DVD
drive.
PAGE –: (HDD) Selects the
internal HDD (hard disk drive).
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: (DRIVE SELECT)
Switches between HDD and DVD.
ȿ
CH +/–: Switches the channel up/
down (for DVD recorder).
Ɂ
ENTER: Enters the selected item.
Blu-ray Disc/HD-DVD player
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records (for BD recorder).
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȳ
MENU: Displays the Pop-up Menu/
Disc Menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +: (BD) Selects the BD drive.
PAGE –: (HDD) Selects the
internal HDD (hard disk drive).
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the options
menu.
Ɂ
ENTER: Enters the selected item.
DVR (digital video recorder)/PVR (personal video recorder)
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: (REPLAY*) Enables the Replay
function for DVR/Replay TV.
B: (Live TV*) Displays Master
Guide.
Ȱ
LIST: Displays the title of recorded
program.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +/–: Page up/down,
Thumbs* up/down
Ȼ
INFO: (DISPLAY) Displays the
playback information.
Ƚ
RECALL: Selects the channel
previously selected.
ȿ
CH +/–: Switches the channel up/
down.
Ɂ
ENTER: Enters the selected item.
* These buttons correspond to TiVo
service or the Replay service. Refer to
its instruction manual for details.
DVD Home Theater
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȱ
LIST: Enables the SOUND FIELD
function.
Ȳ
MENU: Displays the DVD menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the amplifier
menu.
Ƚ
RECALL: (BAND) Selects FM/AM.
ȿ
CH +/–: Presets or tunes frequency
up/down.
Ɂ
ENTER: Enters the selected item.
Notes on using the RM-VZ220
ˎ
The RM-VZ220 will not perform functions that the device is not designed for. For
example, if your TV does not have the muting function, MUTING on the RM-VZ220
will not function with your TV.
ˎ
The function of the buttons varies depending on settings/operating modes. The table
of “Remote Button Descriptions” shows how the RM-VZ220 generally operates for
each device in the preset mode.
ˎ
If your cable set top box can control volume, be sure to set its volume to a moderate
level. If the volume on the cable set top box is turned down completely, you will not be
able to adjust your TV’s volume with the RM-VZ220.
Manufacturer’s Code List /
Lista de códigos del fabricante
English
The following tables show brand names (Brand) and their corresponding
code numbers (Code No.).
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2 Enter the manufacturer’s code.
The SET indicator flashes three times and turns off.
Español
La siguiente tabla muestra los nombres de las marcas (Brand) y el número
de código correspondiente (Code No.).
1 Presione y mantenga presionado el botón SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras tiene presionado el botón SET, presione el botón de selección de
dispositivo deseado y luego suelte ambos botones.
2 Ingrese el código del fabricante.
El indicador SET parpadeará tres veces y se apagará.
Brand Code No.
Acer 01339
Action 00650
Admiral 00463
Akai 00812, 01675, 00702, 02232
Akira 01733
AOC 01365, 01589
Apex Digital 00748
Aventura 00171
Bell & Howell 00154
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Dynex 01463, 01810, 02049
Electroband 00000
Electrograph 01755
Electrohome 00463
Elektra 01661
Element 01687
Emerson 01864, 00154, 00463, 00171,
01661, 01394
Emprex 01765
Envision 01365, 01589
ESA 00812, 00171
Fisher 00154
Funai 00171
Gateway 01755, 01756
GE 01447, 00051, 02359
GFM 00171
Haier 01748, 01749, 02309, 02449
Harman/Kardon 00054
Hisense 00748, 01314, 02098
Hitachi 01643, 02215, 02433
iLo 01684
Infinity 00054
Insignia 01564, 00171, 02049
JBL 00054
JCB 00000
JVC 00731, 01253, 01601, 01774
KDS 01687
Kolin 01331
LG 01423, 02358
LXI 00054, 00154, 00156
MAG 01687
Magnavox 01454, 01866, 00054, 01254,
01365, 02372
Marantz 00054
Matsushita 00650
Maxent 01755
Memorex 00154, 00463, 00150
MGA 00150
Midland 00051
Brand Code No.
Mitsubishi 01250, 00150, 00836
NAD 00156
NEC 01797
NetTV 01755
Norcent 00748, 01365, 01589
Olevia 01610, 01144, 01331
Onida 01253, 02396
Optimus 00154, 00650
Orion 00463, 01463
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
Quasar 00051, 00650
RadioShack 00154
RCA 01447, 01781, 02187, 02247,
02403, 02429, 02434
Realistic 00154
Sampo 01755
Samsung 00812, 00702
Sansui 00463
Sanyo 00154, 01142
Sceptre 01360, 01599
Scott 01711
Sears 00054, 00154, 00156, 00171
Sharp 00818
Sony 00810, 00000
Spectroniq 01687
Squareview 00171
Superscan 00864
Supreme 00000
SVA 00748
Sylvania 01864, 00054, 00171, 01314,
01394
Symphonic 00171
Syntax 01610, 01144, 01331
Tatung 01756
TCL 02403, 02429
Technics 00051
Techwood 00051
Teknika 00054, 00150
Telefunken 00702
Toshiba 01524, 00154, 00156, 00650
TVS 00463
Venturer 01865
Videocon 01540, 01541, 02436
Vidikron 00054
Viewsonic 01755, 00864, 00885, 01627,
01742
Viore 01684, 02104, 02352
Vizio 01758, 00864, 00885, 01756
VU 02098
TV / TV
Brand Code No.
Wards 00054
Waycon 00156
Westinghouse 01712, 00885, 01577
White
Westinghouse
00463, 01661
Wyse 01365
Zenith 00463, 01661
Brand Code No.
Accurian 10675
Akai 10695
Allegro 10869
Apex Digital 10672, 11056
Bel Canto Design 11571
Broksonic 10695
CineVision 10869
Citizen 10695
CyberHome 11024
Daewoo 10869
Denon 10490, 11634, 12258
Disney 10675, 11270
Emerson 10591, 10675
Enterprise 10591
Funai 10675
GE 10522
GFM 10675
Go Video 10744, 10741, 10869, 11044,
11075
GoldStar 10741
Harman/Kardon 11229
Hitachi 10573, 10664
Hiteker 10672
Insignia 10675, 12428, 12596
Integra 11769, 10627, 12147
JVC 10623, 10867, 11164
Kenwood 10490
LG 10591, 10741, 10869
Magnavox 10503, 10539, 10646, 10675,
11354
Marantz 10539, 12414, 12432
Memorex 10695, 11270, 12213
Microsoft 10522, 12083
Mitsubishi 11521
NAD 10741, 12572
Olevia 12331
Onkyo 10503, 11769, 10627, 11627,
12147
Brand Code No.
Oppo 10575, 12545
Panasonic 10490, 11579, 11641
Philco 10675
Philips 10503, 10539, 12056, 12084,
10646, 10675, 11267, 11354,
12434
Pioneer 10142, 10631, 11571, 12442
Polk Audio 10539
Presidian 10675
Proscan 10522
RCA 10522, 11769, 10822, 12213,
12587, 12592, 12594
Rio 10869
Rotel 10623
Samsung 10490, 10573, 10199, 11044,
11075, 12329, 12489
Sansui 10695
Sanyo 10695
Sharp 10630, 10675, 12250
Shinsonic 10533
Sonic Blue 10869
Sony 11633, 10533, 10864, 11033,
11070, 11431, 11516
Sylvania 10675
Symphonic 10675
TCL 12587
Technics 10490
Tivo 11503
Toshiba 10503, 11769, 10695, 11154,
11503, 12006, 12277
Urban Concepts 10503
Viore 12553
Vizio 12563
Vtrek 12587
Xbox 10522, 12083
Yamaha 10490, 10539, 10497, 10817,
12298
Zenith 10503, 10591, 10741, 10869
DVD player / Reproductor de DVD
Brand Code No.
Accurian 10675
Apex Digital 11056
Funai 10675
Go Video 10741
JVC 11164
LG 10741
Magnavox 10646, 10675
Panasonic 10490, 11579
Philips 10646
Brand Code No.
Pioneer 10631
RCA 10522
Samsung 10490
Sharp 10675
Sony 11033, 11070, 11431
Sylvania 10675
Toshiba 12277
Zenith 10741
DVD recorder / Grabadora de DVD
Blu-ray Disc/HD-DVD player/
Reproductor de Blu-ray Disc/HD-DVD
Brand Code No.
Denon 12258
Insignia 10675, 12428, 12596
Integra 11769, 12147
LG 10741
Magnavox 10675
Marantz 12414, 12432
Microsoft 12083
NAD 12572
Olevia 12331
Onkyo 11769, 12147
Oppo 12545
Panasonic 11641
Brand Code No.
Philips 12084, 12434
Pioneer 10142, 12442
RCA 11769
Samsung 10199
Sharp 12250
Sony 11516
Sylvania 10675
Toshiba 11769
Viore 12553
Vizio 12563
Xbox 12083
Yamaha 12298
RM-VZ220_U [US,ES] 4-170-642-12(1)RM-VZ220_U [US,ES] 4-170-642-12(1)
4-170-642-12(1)
Remote Commander
RM-VZ220
©2010 Sony Corporation Printed in China
Operating Instructions
Manual de instrucciones (parte posterior)
English
For the Customers in the U.S.A.
WARNING
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
ˎ
Reorient or relocate the receiving antenna.
ˎ
Increase the separation between the equipment and receiver.
ˎ
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
ˎ
Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this
manual could void your authority to operate this equipment.
Setting Up the RM-VZ220
The RM-VZ220 is preset at the factory to operate Sony brand video devices
set to any of the Device Select buttons (see the table below).
To use with non-Sony devices, or Sony devices that are not preset at the
factory, set the manufacturer’s code for each device.
Devices Button Factory setting*
TV
TV
Sony TV (00810)
TV, Cable set top box, Satellite
receiver, IPTV, DVD player, DVD
recorder, Blu-ray Disc player, DVR
(digital video recorder), PVR
(personal video recorder), VCR,
DVD Home Theater
CBL (SAT)
Cable set top box (non-
Sony) (51376)
VCR
Sony VCR (60032)
DVD
Sony DVD player
(11033)
* The five-digit code is the preset manufacturer’s code.
Note
Only a TV can be assigned to the TV Device Select button. You can assign any device to
the other Device Select buttons.
Installing the batteries
Slide open the battery compartment and insert two size AA (R6) dry
batteries (not supplied).
Insert the batteries (negative end first) through the guide clamp within each
compartment as shown below.
1 2
Battery life
Under normal conditions, size AA (LR6) alkaline batteries will last up to one
year. If the RM-VZ220 does not operate properly, the batteries might be
drained. Replace both batteries with new ones.
Notes
ˎ
Replace the batteries within 2 minutes after removing them, and do not press any
button when replacing the batteries. Otherwise, your code settings may be cleared.
ˎ
Do not use an old battery with a new one, or mix different types of batteries together.
ˎ
If the electrolyte inside the battery should leak, wipe the contaminated area of the
battery compartment with a cloth and replace the old batteries with new ones. To
prevent electrolyte from leaking, remove the batteries when you plan not to use the
RM-VZ220 for a long period of time.
Specifications
Operating distance Approx. 11 m (36 ft) (varies depending on devices of
different manufacturers)
Power requirements Two size AA (R6) dry batteries (not supplied)
Battery life Approx. 1 year when using size AA (LR6) alkaline batteries
(varies depending on frequency of button use - up to approx.
300 times per day.)
Dimensions Approx. 53 × 213 × 27 mm (2
1
/
8
× 8
1
/
2
× 1
1
/
8
in.)
(w/h/d)
Mass Approx. 100 g (3.5 oz) (not including batteries)
Design and specifications are subject to change without notice.
Troubleshooting
If you have problems setting up or using the RM-VZ220:
ˎ
Carefully perform the setup procedure of “Startup Guide.” If the RM-VZ220 does not
work, try repeating the setup procedure using another manufacturer’s code (if listed
for your device). If you still cannot operate the RM-VZ220, try the Search function
(see “Searching for the correct code”).
ˎ
Aim the RM-VZ220 directly at the device.
ˎ
Remove any obstacles in the path between the RM-VZ220 and the device.
ˎ
Make sure you have pressed the correct Device Select button.
ˎ
Check that the device has infrared remote capability. For example, if your device did
not come with a remote control, it probably is not capable of being controlled by the
RM-VZ220.
ˎ
The batteries are weak, or not inserted correctly. Replace them with new ones or insert
them correctly.
For the customers in the U.S.A.
Customer Support Information
After you have read through this manual, if you still cannot get the RM-VZ220 to work
properly, call the Sony Customer Support Helpline at
1-800-822-2217.
Startup Guide
This guide shows you how to set up and use the RM-VZ220 to operate your devices.
If your Sony device has already been preset, see “Operate the device.”
Set the manufacturer’s code
Example: To set up a Philips TV
1
Find the manufacturer’s code in “Manufacturer’s Code List.”
Manufacturer’s Code List /
Lista de códigos del fabricante
English
The following tables show brand names (Brand) and their corresponding
code numbers (Code No.).
1 Press and hold SET for more than 3 seconds.
TheSET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2 Enter the manufacturer’s code.
TheSET indicator flashes three times and turns off.
Español
La siguiente tabla muestra los nombres de las marcas (Brand) y el número
de código correspondiente (Code No.).
1 Presione y mantenga presionado el botón SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras tiene presionado el botón SET, presione el botón de selección de
dispositivo deseado y luego suelte ambos botones.
2 Ingrese el código del fabricante.
El indicador SET parpadeará tres veces y se apagará.
Brand Code No.
Sony 00810, 00000
Acer 01339
Action 00650
Admiral 00463
Akai 00812, 01675, 00702, 02232
Akira 01733
AOC 01365, 01589
Apex Digital 00748
Aventura 00171
Bell & Howell 00154
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Dynex 01463, 01810, 02049
Electroband 00000
Electrograph 01755
Electrohome 00463
Elektra 01661
Element 01687
Emerson 01864, 00154, 00463, 00171,
01661, 01394
Emprex 01765
Envision 01365, 01589
ESA 00812, 00171
Fisher 00154
Funai 00171
Gateway 01755, 01756
GE 01447, 00051, 02359
GFM 00171
Haier 01748, 01749, 02309, 02449
Harman/Kardon 00054
Hisense 00748, 01314, 02098
Hitachi 01643, 02215, 02433
iLo 01684
Infinity 00054
Insignia 01564, 00171, 02049
JBL 00054
JCB 00000
JVC 00731, 01253, 01601, 01774
KDS 01687
Kolin 01331
LG 01423, 02358
LXI 00054, 00154, 00156
MAG 01687
Magnavox 01454, 01866, 00054, 01254,
01365, 02372
Marantz 00054
Matsushita 00650
Maxent 01755
Memorex 00154, 00463, 00150
MGA 00150
Brand Code No.
Midland 00051
Mitsubishi 01250, 00150, 00836
NAD 00156
NEC 01797
NetTV 01755
Norcent 00748, 01365, 01589
Olevia 01610, 01144, 01331
Onida 01253, 02396
Optimus 00154, 00650
Orion 00463, 01463
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
Quasar 00051, 00650
RadioShack 00154
RCA 01447, 01781, 02187, 02247,
02403, 02429, 02434
Realistic 00154
Sampo 01755
Samsung 00812, 00702
Sansui 00463
Sanyo 00154, 01142
Sceptre 01360, 01599
Scott 01711
Sears 00054, 00154, 00156, 00171
Sharp 00818
Spectroniq 01687
Squareview 00171
Superscan 00864
Supreme 00000
SVA 00748
Sylvania 01864, 00054, 00171, 01314,
01394
Symphonic 00171
Syntax 01610, 01144, 01331
Tatung 01756
TCL 02403, 02429
Technics 00051
Techwood 00051
Teknika 00054, 00150
Telefunken 00702
Toshiba 01524, 00154, 00156, 00650
TVS 00463
Venturer 01865
Videocon 01540, 01541, 02436
Vidikron 00054
Viewsonic 01755, 00864, 00885, 01627,
01742
Viore 01684, 02104, 02352
Vizio 01758, 00864, 00885, 01756
VU 02098
TV / TV
Brand Code No.
Wards 00054
Waycon 00156
Westinghouse 01712, 00885, 01577
White
Westinghouse
00463, 01661
Wyse 01365
Zenith 00463, 01661
Brand Code No.
Sony 11633, 10533, 10864, 11033,
11070, 11431, 11516
Accurian 10675
Akai 10695
Allegro 10869
Apex Digital 10672, 11056
Bel Canto Design 11571
Broksonic 10695
CineVision 10869
Citizen 10695
CyberHome 11024
Daewoo 10869
Denon 10490, 11634, 12258
Disney 10675, 11270
Emerson 10591, 10675
Enterprise 10591
Funai 10675
GE 10522
GFM 10675
Go Video 10744, 10741, 10869, 11044,
11075
GoldStar 10741
Harman/Kardon 11229
Hitachi 10573, 10664
Hiteker 10672
Insignia 10675, 12428, 12596
Integra 11769, 10627, 12147
JVC 10623, 10867, 11164
Kenwood 10490
LG 10591, 10741, 10869
Magnavox 10503, 10539, 10646, 10675,
11354
Marantz 10539, 12414, 12432
Memorex 10695, 11270, 12213
Microsoft 10522, 12083
Mitsubishi 11521
NAD 10741, 12572
Olevia 12331
Brand Code No.
Onkyo 10503, 11769, 10627, 11627,
12147
Oppo 10575, 12545
Panasonic 10490, 11579, 11641
Philco 10675
Philips 10503, 10539, 12056, 12084,
10646, 10675, 11267, 11354,
12434
Pioneer 10142, 10631, 11571, 12442
Polk Audio 10539
Presidian 10675
Proscan 10522
RCA 10522, 11769, 10822, 12213,
12587, 12592, 12594
Rio 10869
Rotel 10623
Samsung 10490, 10573, 10199, 11044,
11075, 12329, 12489
Sansui 10695
Sanyo 10695
Sharp 10630, 10675, 12250
Shinsonic 10533
Sonic Blue 10869
Sylvania 10675
Symphonic 10675
TCL 12587
Technics 10490
Tivo 11503
Toshiba 10503, 11769, 10695, 11154,
11503, 12006, 12277
Urban Concepts 10503
Viore 12553
Vizio 12563
Vtrek 12587
Xbox 10522, 12083
Yamaha 10490, 10539, 10497, 10817,
12298
Zenith 10503, 10591, 10741, 10869
DVD player / Reproductor de DVD
Brand Code No.
Sony 11033, 11070, 11431
Accurian 10675
Apex Digital 11056
Funai 10675
Go Video 10741
JVC 11164
LG 10741
Magnavox 10646, 10675
Panasonic 10490, 11579
Brand Code No.
Philips 10646
Pioneer 106 31
RCA 10522
Samsung 10490
Sharp 10675
Sylvania 10675
Toshiba 12277
Zenith 10741
DVD recorder / Grabadora de DVD
Blu-ray Disc/HD-DVD player/
Reproductor de Blu-ray Disc/HD-DVD
Brand Code No.
Sony 11516
Denon 12258
Insignia 10675, 12428, 12596
Integra 11769, 12147
LG 10741
Magnavox 10675
Marantz 12414, 12432
Microsoft 12083
NAD 12572
Olevia 12331
Onkyo 11769, 12147
Oppo 12545
Brand Code No.
Panasonic 11641
Philips 12084, 12434
Pioneer 10142, 12442
RCA 11769
Samsung 10199
Sharp 12250
Sylvania 10675
Toshiba 11769
Viore 12553
Vizio 12563
Xbox 12083
Yamaha 12298
Brand Code No.
Sony 00810, 00000
Acer 01339
Action 00650
Brand Code No.
Midland 00051
Mitsubishi 01250, 00150, 00836
NAD 00156
TV / TV
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
If your device is not listed, try the Search function (see “Searching for the correct code”).
2
Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
the desired Device Select button,
then release both buttons.
3
Enter the manufacturer’s code (01454).
The SET indicator flashes three times and
turns off.
Operate the device
1
Aim the RM-VZ220 directly at the device.
2
Press the Device Select button for the
device you want to operate.
3
Press POWER to turn on the device.
4
Press buttons on the RM-VZ220 to check that they function.
See “Remote Button Descriptions” for the functions of buttons for each device.
If the RM-VZ220 does not seem to be working…
ˎ
Check that you have set the correct manufacturer’s code.
ˎ
Try repeating the setup procedure using another manufacturer’s code (if listed for your device).
If you still cannot operate the RM-VZ220 after trying all the listed codes, try the Search function (see “Searching
for the correct code”).
Notes
ˎ
If the setting is incomplete,
the SET indicator flashes once
and the indicators turn off.
Start again from the
beginning.
ˎ
If no operations are
performed for 10 seconds
while setting, the setting will
be canceled, and must be
restarted.
ˎ
To cancel the process, press
SET any time. The SET
indicator turns off.
SET
POWER
Device
Select
buttons
Number
buttons
The SET indicator
lights up.
Searching for the correct code
You can set the manufacturer’s code using the Search function.
1 Power on the device with its power switch.
2 Aim the RM-VZ220 at the device you want to set.
3 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
4 Enter 9 - 2 - 2 using the number buttons.
The SET indicator flashes three times.
5 Press and hold à to start searching.
When the device turns off, release the button.
If you overshoot the required code, you can search for the next or previous
code using the
ß
or
ù
button.
6 Press
.
The SET indicator flashes three times and turns off.
7 Check if the code number works correctly (see “Remote Button
Descriptions”).
If you still cannot operate the device, repeat steps to search for another
code that works for most functions of your device.
Checking the manufacturer’s code you have set
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2 Enter 9 - 3 - 3 using the number buttons.
The SET indicator flashes three times.
3 Press à.
4 When the SET indicator starts flashing, count the number of flashes.
Short flash(es) indicate which digit (first, second, etc.), followed by long
flash(es) to indicate the digit number (i.e., 2 long flashes represent the
number 2). “0” is indicated by rapid flashing.
Determine the 5-digit code number this way. To recheck, press à.
5 Press SET to finish.
Clearing the automatic power-on control (Sony
devices only)
The Device Select buttons are preset to automatically turn on a device when
pressed.
To cancel the function:
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
, then release both buttons.
2 Enter 9 - 7 - 7 using the number buttons.
The SET indicator flashes three times.
3 Press the desired Device Select button.
The SET indicator flashes three times and turns off.
To set the function again, perform the same procedure above.
Restoring the factory settings
You can clear all the settings and reset the RM-VZ220 to its factory settings.
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
, then release both buttons.
2 Enter 9 - 0 - 0 using the number buttons.
The SET indicator flashes three times.
To cancel, press any button except
.
3 Press
.
The SET indicator flashes three times and turns off.
Remote Button Descriptions
General
ȩȪ
SET: Press to set up the RM-VZ220. The indicator lights or flashes while
setting.
ȫ
Device Select buttons: Press to select the device to operate.
Ȯ
GUIDE: Displays the program guide (EPG).
ȯ
j//V/p/
: Moves the cursor to select a menu item/enters the selected item.
ȱ
RETURN: Returns to the previous display/exits the menu.
ȳ
VOL +/–: Turns the volume up/down.
ȸ
POWER: Turns the selected device on and off.
Ⱦ
MUTING: Mutes the volume. Press again to turn muting off.
ɀ
SLEEP: Enables the Sleep function (when available).
The number 5, CH+, and à buttons each have a tactile dot for ease of use.
The GUIDE and RETURN buttons do not work for a VCR.
Note on the VOL+/– and MUTING buttons
When a TV or other video device is selected, the TV’s volume is controlled. When a
DVD Home Theater is selected, its volume can be controlled.
TV
Ȭ
Ã
: VIDEO 1 input
: VIDEO 2 input
: HDMI input
Ñ
: RGB input
ù
: (PIP INPUT) Changes the
input mode of the “window”
picture.
à
: (PIP) Turns the “window”
picture on and off.
ß
: (PIP MOVE) Moves the
location of the “window” picture.
ê
: (PIP STILL) Freezes the
“window” picture.
Ą
: (PIP SWAP) Switches between
“main” and “window” picture.
ȭ
A: Red button
B: Green button
C: Yellow button
D: Blue button
Ȱ
LIST: (CAPTION) Displays closed
captioning.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵȶɁ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: (PIP CH +/–) Changes
the channel up/down in the
“window” picture.
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: Selects the channel
previously selected.
ȿ
CH +/–: Switches the channel up/
down.
Cable set top box/IPTV
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A, B, C buttons
D: (Live TV) Displays Master
Guide.
Ȱ
LIST: Displays the title of recorded
program.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵ ȶ Ɂ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: Page up/down
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: Switches between the
current and previous channel.
ȿ
CH +/–: Switches the channel up/
down.
Satellite receiver
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: Red button
B: Green button
C: Yellow button
D: Blue button
Ȱ
LIST: Displays the title of recorded
program/PVR menu.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: (TV/SAT) Switches the
output between SAT and TV.
ȵ ȶ Ɂ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: Page up/down
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the Satellite
dish menu/Station Index.
Ƚ
RECALL: Tunes to the last tuned
station.
ȿ
CH +/–: Switches the channel up/
down.
VCR
Ȭ
ù
: Rewinds.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȷ
ì: Ejects a tape.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: (ANT/SW) Switches
the antenna output.
Ƚ
RECALL: (DRIVE SELECT) Selects
the deck.
ȿ
CH +/–: Switches the channel up/
down.
Ɂ
ENTER: Enters the selected item.
DVD player/recorder
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records (for DVD recorder).
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȱ
LIST: Displays the Title List.
Ȳ
MENU: Displays the DVD menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +: (DVD) Selects the DVD
drive.
PAGE –: (HDD) Selects the
internal HDD (hard disk drive).
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: (DRIVE SELECT)
Switches between HDD and DVD.
ȿ
CH +/–: Switches the channel up/
down (for DVD recorder).
Ɂ
ENTER: Enters the selected item.
Blu-ray Disc/HD-DVD player
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records (for BD recorder).
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȳ
MENU: Displays the Pop-up Menu/
Disc Menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +: (BD) Selects the BD drive.
PAGE –: (HDD) Selects the
internal HDD (hard disk drive).
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the options
menu.
Ɂ
ENTER: Enters the selected item.
DVR (digital video recorder)/PVR (personal video recorder)
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: (REPLAY*) Enables the Replay
function for DVR/Replay TV.
B: (Live TV*) Displays Master
Guide.
Ȱ
LIST: Displays the title of recorded
program.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +/–: Page up/down,
Thumbs* up/down
Ȼ
INFO: (DISPLAY) Displays the
playback information.
Ƚ
RECALL: Selects the channel
previously selected.
ȿ
CH +/–: Switches the channel up/
down.
Ɂ
ENTER: Enters the selected item.
* These buttons correspond to TiVo
service or the Replay service. Refer to
its instruction manual for details.
DVD Home Theater
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȱ
LIST: Enables the SOUND FIELD
function.
Ȳ
MENU: Displays the DVD menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the amplifier
menu.
Ƚ
RECALL: (BAND) Selects FM/AM.
ȿ
CH +/–: Presets or tunes frequency
up/down.
Ɂ
ENTER: Enters the selected item.
Notes on using the RM-VZ220
ˎ
The RM-VZ220 will not perform functions that the device is not designed for. For
example, if your TV does not have the muting function, MUTING on the RM-VZ220
will not function with your TV.
ˎ
The function of the buttons varies depending on settings/operating modes. The table
of “Remote Button Descriptions” shows how the RM-VZ220 generally operates for
each device in the preset mode.
ˎ
If your cable set top box can control volume, be sure to set its volume to a moderate
level. If the volume on the cable set top box is turned down completely, you will not be
able to adjust your TV’s volume with the RM-VZ220.
Manufacturer’s Code List /
Lista de códigos del fabricante
English
The following tables show brand names (Brand) and their corresponding
code numbers (Code No.).
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2 Enter the manufacturer’s code.
The SET indicator flashes three times and turns off.
Español
La siguiente tabla muestra los nombres de las marcas (Brand) y el número
de código correspondiente (Code No.).
1 Presione y mantenga presionado el botón SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras tiene presionado el botón SET, presione el botón de selección de
dispositivo deseado y luego suelte ambos botones.
2 Ingrese el código del fabricante.
El indicador SET parpadeará tres veces y se apagará.
Brand Code No.
Acer 01339
Action 00650
Admiral 00463
Akai 00812, 01675, 00702, 02232
Akira 01733
AOC 01365, 01589
Apex Digital 00748
Aventura 00171
Bell & Howell 00154
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Dynex 01463, 01810, 02049
Electroband 00000
Electrograph 01755
Electrohome 00463
Elektra 01661
Element 01687
Emerson 01864, 00154, 00463, 00171,
01661, 01394
Emprex 01765
Envision 01365, 01589
ESA 00812, 00171
Fisher 00154
Funai 00171
Gateway 01755, 01756
GE 01447, 00051, 02359
GFM 00171
Haier 01748, 01749, 02309, 02449
Harman/Kardon 00054
Hisense 00748, 01314, 02098
Hitachi 01643, 02215, 02433
iLo 01684
Infinity 00054
Insignia 01564, 00171, 02049
JBL 00054
JCB 00000
JVC 00731, 01253, 01601, 01774
KDS 01687
Kolin 01331
LG 01423, 02358
LXI 00054, 00154, 00156
MAG 01687
Magnavox 01454, 01866, 00054, 01254,
01365, 02372
Marantz 00054
Matsushita 00650
Maxent 01755
Memorex 00154, 00463, 00150
MGA 00150
Midland 00051
Brand Code No.
Mitsubishi 01250, 00150, 00836
NAD 00156
NEC 01797
NetTV 01755
Norcent 00748, 01365, 01589
Olevia 01610, 01144, 01331
Onida 01253, 02396
Optimus 00154, 00650
Orion 00463, 01463
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
Quasar 00051, 00650
RadioShack 00154
RCA 01447, 01781, 02187, 02247,
02403, 02429, 02434
Realistic 00154
Sampo 01755
Samsung 00812, 00702
Sansui 00463
Sanyo 00154, 01142
Sceptre 01360, 01599
Scott 01711
Sears 00054, 00154, 00156, 00171
Sharp 00818
Sony 00810, 00000
Spectroniq 01687
Squareview 00171
Superscan 00864
Supreme 00000
SVA 00748
Sylvania 01864, 00054, 00171, 01314,
01394
Symphonic 00171
Syntax 01610, 01144, 01331
Tatung 01756
TCL 02403, 02429
Technics 00051
Techwood 00051
Teknika 00054, 00150
Telefunken 00702
Toshiba 01524, 00154, 00156, 00650
TVS 00463
Venturer 01865
Videocon 01540, 01541, 02436
Vidikron 00054
Viewsonic 01755, 00864, 00885, 01627,
01742
Viore 01684, 02104, 02352
Vizio 01758, 00864, 00885, 01756
VU 02098
TV / TV
Brand Code No.
Wards 00054
Waycon 00156
Westinghouse 01712, 00885, 01577
White
Westinghouse
00463, 01661
Wyse 01365
Zenith 00463, 01661
Brand Code No.
Accurian 10675
Akai 10695
Allegro 10869
Apex Digital 10672, 11056
Bel Canto Design 11571
Broksonic 10695
CineVision 10869
Citizen 10695
CyberHome 11024
Daewoo 10869
Denon 10490, 11634, 12258
Disney 10675, 11270
Emerson 10591, 10675
Enterprise 10591
Funai 10675
GE 10522
GFM 10675
Go Video 10744, 10741, 10869, 11044,
11075
GoldStar 10741
Harman/Kardon 11229
Hitachi 10573, 10664
Hiteker 10672
Insignia 10675, 12428, 12596
Integra 11769, 10627, 12147
JVC 10623, 10867, 11164
Kenwood 10490
LG 10591, 10741, 10869
Magnavox 10503, 10539, 10646, 10675,
11354
Marantz 10539, 12414, 12432
Memorex 10695, 11270, 12213
Microsoft 10522, 12083
Mitsubishi 11521
NAD 10741, 12572
Olevia 12331
Onkyo 10503, 11769, 10627, 11627,
12147
Brand Code No.
Oppo 10575, 12545
Panasonic 10490, 11579, 11641
Philco 10675
Philips 10503, 10539, 12056, 12084,
10646, 10675, 11267, 11354,
12434
Pioneer 10142, 10631, 11571, 12442
Polk Audio 10539
Presidian 10675
Proscan 10522
RCA 10522, 11769, 10822, 12213,
12587, 12592, 12594
Rio 10869
Rotel 10623
Samsung 10490, 10573, 10199, 11044,
11075, 12329, 12489
Sansui 10695
Sanyo 10695
Sharp 10630, 10675, 12250
Shinsonic 10533
Sonic Blue 10869
Sony 11633, 10533, 10864, 11033,
11070, 11431, 11516
Sylvania 10675
Symphonic 10675
TCL 12587
Technics 10490
Tivo 11503
Toshiba 10503, 11769, 10695, 11154,
11503, 12006, 12277
Urban Concepts 10503
Viore 12553
Vizio 12563
Vtrek 12587
Xbox 10522, 12083
Yamaha 10490, 10539, 10497, 10817,
12298
Zenith 10503, 10591, 10741, 10869
DVD player / Reproductor de DVD
Brand Code No.
Accurian 10675
Apex Digital 11056
Funai 10675
Go Video 10741
JVC 11164
LG 10741
Magnavox 10646, 10675
Panasonic 10490, 11579
Philips 10646
Brand Code No.
Pioneer 10631
RCA 10522
Samsung 10490
Sharp 10675
Sony 11033, 11070, 11431
Sylvania 10675
Toshiba 12277
Zenith 10741
DVD recorder / Grabadora de DVD
Blu-ray Disc/HD-DVD player/
Reproductor de Blu-ray Disc/HD-DVD
Brand Code No.
Denon 12258
Insignia 10675, 12428, 12596
Integra 11769, 12147
LG 10741
Magnavox 10675
Marantz 12414, 12432
Microsoft 12083
NAD 12572
Olevia 12331
Onkyo 11769, 12147
Oppo 12545
Panasonic 11641
Brand Code No.
Philips 12084, 12434
Pioneer 10142, 12442
RCA 11769
Samsung 10199
Sharp 12250
Sony 11516
Sylvania 10675
Toshiba 11769
Viore 12553
Vizio 12563
Xbox 12083
Yamaha 12298
RM-VZ220_U [US,ES] 4-170-642-12(1)RM-VZ220_U [US,ES] 4-170-642-12(1)
4-170-642-12(1)
Remote Commander
RM-VZ220
©2010 Sony Corporation Printed in China
Operating Instructions
Manual de instrucciones (parte posterior)
English
For the Customers in the U.S.A.
WARNING
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
ˎ
Reorient or relocate the receiving antenna.
ˎ
Increase the separation between the equipment and receiver.
ˎ
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
ˎ
Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this
manual could void your authority to operate this equipment.
Setting Up the RM-VZ220
The RM-VZ220 is preset at the factory to operate Sony brand video devices
set to any of the Device Select buttons (see the table below).
To use with non-Sony devices, or Sony devices that are not preset at the
factory, set the manufacturer’s code for each device.
Devices Button Factory setting*
TV
TV
Sony TV (00810)
TV, Cable set top box, Satellite
receiver, IPTV, DVD player, DVD
recorder, Blu-ray Disc player, DVR
(digital video recorder), PVR
(personal video recorder), VCR,
DVD Home Theater
CBL (SAT)
Cable set top box (non-
Sony) (51376)
VCR
Sony VCR (60032)
DVD
Sony DVD player
(11033)
* The five-digit code is the preset manufacturer’s code.
Note
Only a TV can be assigned to the TV Device Select button. You can assign any device to
the other Device Select buttons.
Installing the batteries
Slide open the battery compartment and insert two size AA (R6) dry
batteries (not supplied).
Insert the batteries (negative end first) through the guide clamp within each
compartment as shown below.
1 2
Battery life
Under normal conditions, size AA (LR6) alkaline batteries will last up to one
year. If the RM-VZ220 does not operate properly, the batteries might be
drained. Replace both batteries with new ones.
Notes
ˎ
Replace the batteries within 2 minutes after removing them, and do not press any
button when replacing the batteries. Otherwise, your code settings may be cleared.
ˎ
Do not use an old battery with a new one, or mix different types of batteries together.
ˎ
If the electrolyte inside the battery should leak, wipe the contaminated area of the
battery compartment with a cloth and replace the old batteries with new ones. To
prevent electrolyte from leaking, remove the batteries when you plan not to use the
RM-VZ220 for a long period of time.
Specifications
Operating distance Approx. 11 m (36 ft) (varies depending on devices of
different manufacturers)
Power requirements Two size AA (R6) dry batteries (not supplied)
Battery life Approx. 1 year when using size AA (LR6) alkaline batteries
(varies depending on frequency of button use - up to approx.
300 times per day.)
Dimensions Approx. 53 × 213 × 27 mm (2
1
/
8
× 8
1
/
2
× 1
1
/
8
in.)
(w/h/d)
Mass Approx. 100 g (3.5 oz) (not including batteries)
Design and specifications are subject to change without notice.
Troubleshooting
If you have problems setting up or using the RM-VZ220:
ˎ
Carefully perform the setup procedure of “Startup Guide.” If the RM-VZ220 does not
work, try repeating the setup procedure using another manufacturer’s code (if listed
for your device). If you still cannot operate the RM-VZ220, try the Search function
(see “Searching for the correct code”).
ˎ
Aim the RM-VZ220 directly at the device.
ˎ
Remove any obstacles in the path between the RM-VZ220 and the device.
ˎ
Make sure you have pressed the correct Device Select button.
ˎ
Check that the device has infrared remote capability. For example, if your device did
not come with a remote control, it probably is not capable of being controlled by the
RM-VZ220.
ˎ
The batteries are weak, or not inserted correctly. Replace them with new ones or insert
them correctly.
For the customers in the U.S.A.
Customer Support Information
After you have read through this manual, if you still cannot get the RM-VZ220 to work
properly, call the Sony Customer Support Helpline at
1-800-822-2217.
Startup Guide
This guide shows you how to set up and use the RM-VZ220 to operate your devices.
If your Sony device has already been preset, see “Operate the device.”
Set the manufacturer’s code
Example: To set up a Philips TV
1
Find the manufacturer’s code in “Manufacturer’s Code List.”
Manufacturer’s Code List /
Lista de códigos del fabricante
English
The following tables show brand names (Brand) and their corresponding
code numbers (Code No.).
1 Press and hold SET for more than 3 seconds.
TheSET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2 Enter the manufacturer’s code.
TheSET indicator flashes three times and turns off.
Español
La siguiente tabla muestra los nombres de las marcas (Brand) y el número
de código correspondiente (Code No.).
1 Presione y mantenga presionado el botón SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras tiene presionado el botón SET, presione el botón de selección de
dispositivo deseado y luego suelte ambos botones.
2 Ingrese el código del fabricante.
El indicador SET parpadeará tres veces y se apagará.
Brand Code No.
Sony 00810, 00000
Acer 01339
Action 00650
Admiral 00463
Akai 00812, 01675, 00702, 02232
Akira 01733
AOC 01365, 01589
Apex Digital 00748
Aventura 00171
Bell & Howell 00154
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Dynex 01463, 01810, 02049
Electroband 00000
Electrograph 01755
Electrohome 00463
Elektra 01661
Element 01687
Emerson 01864, 00154, 00463, 00171,
01661, 01394
Emprex 01765
Envision 01365, 01589
ESA 00812, 00171
Fisher 00154
Funai 00171
Gateway 01755, 01756
GE 01447, 00051, 02359
GFM 00171
Haier 01748, 01749, 02309, 02449
Harman/Kardon 00054
Hisense 00748, 01314, 02098
Hitachi 01643, 02215, 02433
iLo 01684
Infinity 00054
Insignia 01564, 00171, 02049
JBL 00054
JCB 00000
JVC 00731, 01253, 01601, 01774
KDS 01687
Kolin 01331
LG 01423, 02358
LXI 00054, 00154, 00156
MAG 01687
Magnavox 01454, 01866, 00054, 01254,
01365, 02372
Marantz 00054
Matsushita 00650
Maxent 01755
Memorex 00154, 00463, 00150
MGA 00150
Brand Code No.
Midland 00051
Mitsubishi 01250, 00150, 00836
NAD 00156
NEC 01797
NetTV 01755
Norcent 00748, 01365, 01589
Olevia 01610, 01144, 01331
Onida 01253, 02396
Optimus 00154, 00650
Orion 00463, 01463
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
Quasar 00051, 00650
RadioShack 00154
RCA 01447, 01781, 02187, 02247,
02403, 02429, 02434
Realistic 00154
Sampo 01755
Samsung 00812, 00702
Sansui 00463
Sanyo 00154, 01142
Sceptre 01360, 01599
Scott 01711
Sears 00054, 00154, 00156, 00171
Sharp 00818
Spectroniq 01687
Squareview 00171
Superscan 00864
Supreme 00000
SVA 00748
Sylvania 01864, 00054, 00171, 01314,
01394
Symphonic 00171
Syntax 01610, 01144, 01331
Tatung 01756
TCL 02403, 02429
Technics 00051
Techwood 00051
Teknika 00054, 00150
Telefunken 00702
Toshiba 01524, 00154, 00156, 00650
TVS 00463
Venturer 01865
Videocon 01540, 01541, 02436
Vidikron 00054
Viewsonic 01755, 00864, 00885, 01627,
01742
Viore 01684, 02104, 02352
Vizio 01758, 00864, 00885, 01756
VU 02098
TV / TV
Brand Code No.
Wards 00054
Waycon 00156
Westinghouse 01712, 00885, 01577
White
Westinghouse
00463, 01661
Wyse 01365
Zenith 00463, 01661
Brand Code No.
Sony 11633, 10533, 10864, 11033,
11070, 11431, 11516
Accurian 10675
Akai 10695
Allegro 10869
Apex Digital 10672, 11056
Bel Canto Design 11571
Broksonic 10695
CineVision 10869
Citizen 10695
CyberHome 11024
Daewoo 10869
Denon 10490, 11634, 12258
Disney 10675, 11270
Emerson 10591, 10675
Enterprise 10591
Funai 10675
GE 10522
GFM 10675
Go Video 10744, 10741, 10869, 11044,
11075
GoldStar 10741
Harman/Kardon 11229
Hitachi 10573, 10664
Hiteker 10672
Insignia 10675, 12428, 12596
Integra 11769, 10627, 12147
JVC 10623, 10867, 11164
Kenwood 10490
LG 10591, 10741, 10869
Magnavox 10503, 10539, 10646, 10675,
11354
Marantz 10539, 12414, 12432
Memorex 10695, 11270, 12213
Microsoft 10522, 12083
Mitsubishi 11521
NAD 10741, 12572
Olevia 12331
Brand Code No.
Onkyo 10503, 11769, 10627, 11627,
12147
Oppo 10575, 12545
Panasonic 10490, 11579, 11641
Philco 10675
Philips 10503, 10539, 12056, 12084,
10646, 10675, 11267, 11354,
12434
Pioneer 10142, 10631, 11571, 12442
Polk Audio 10539
Presidian 10675
Proscan 10522
RCA 10522, 11769, 10822, 12213,
12587, 12592, 12594
Rio 10869
Rotel 10623
Samsung 10490, 10573, 10199, 11044,
11075, 12329, 12489
Sansui 10695
Sanyo 10695
Sharp 10630, 10675, 12250
Shinsonic 10533
Sonic Blue 10869
Sylvania 10675
Symphonic 10675
TCL 12587
Technics 10490
Tivo 11503
Toshiba 10503, 11769, 10695, 11154,
11503, 12006, 12277
Urban Concepts 10503
Viore 12553
Vizio 12563
Vtrek 12587
Xbox 10522, 12083
Yamaha 10490, 10539, 10497, 10817,
12298
Zenith 10503, 10591, 10741, 10869
DVD player / Reproductor de DVD
Brand Code No.
Sony 11033, 11070, 11431
Accurian 10675
Apex Digital 11056
Funai 10675
Go Video 10741
JVC 11164
LG 10741
Magnavox 10646, 10675
Panasonic 10490, 11579
Brand Code No.
Philips 10646
Pioneer 106 31
RCA 10522
Samsung 10490
Sharp 10675
Sylvania 10675
Toshiba 12277
Zenith 10741
DVD recorder / Grabadora de DVD
Blu-ray Disc/HD-DVD player/
Reproductor de Blu-ray Disc/HD-DVD
Brand Code No.
Sony 11516
Denon 12258
Insignia 10675, 12428, 12596
Integra 11769, 12147
LG 10741
Magnavox 10675
Marantz 12414, 12432
Microsoft 12083
NAD 12572
Olevia 12331
Onkyo 11769, 12147
Oppo 12545
Brand Code No.
Panasonic 11641
Philips 12084, 12434
Pioneer 10142, 12442
RCA 11769
Samsung 10199
Sharp 12250
Sylvania 10675
Toshiba 11769
Viore 12553
Vizio 12563
Xbox 12083
Yamaha 12298
Brand Code No.
Sony 00810, 00000
Acer 01339
Action 00650
Brand Code No.
Midland 00051
Mitsubishi 01250, 00150, 00836
NAD 00156
TV / TV
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
If your device is not listed, try the Search function (see “Searching for the correct code”).
2
Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
the desired Device Select button,
then release both buttons.
3
Enter the manufacturer’s code (01454).
The SET indicator flashes three times and
turns off.
Operate the device
1
Aim the RM-VZ220 directly at the device.
2
Press the Device Select button for the
device you want to operate.
3
Press POWER to turn on the device.
4
Press buttons on the RM-VZ220 to check that they function.
See “Remote Button Descriptions” for the functions of buttons for each device.
If the RM-VZ220 does not seem to be working…
ˎ
Check that you have set the correct manufacturer’s code.
ˎ
Try repeating the setup procedure using another manufacturer’s code (if listed for your device).
If you still cannot operate the RM-VZ220 after trying all the listed codes, try the Search function (see “Searching
for the correct code”).
Notes
ˎ
If the setting is incomplete,
the SET indicator flashes once
and the indicators turn off.
Start again from the
beginning.
ˎ
If no operations are
performed for 10 seconds
while setting, the setting will
be canceled, and must be
restarted.
ˎ
To cancel the process, press
SET any time. The SET
indicator turns off.
SET
POWER
Device
Select
buttons
Number
buttons
The SET indicator
lights up.
Searching for the correct code
You can set the manufacturer’s code using the Search function.
1 Power on the device with its power switch.
2 Aim the RM-VZ220 at the device you want to set.
3 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
4 Enter 9 - 2 - 2 using the number buttons.
The SET indicator flashes three times.
5 Press and hold à to start searching.
When the device turns off, release the button.
If you overshoot the required code, you can search for the next or previous
code using the
ß
or
ù
button.
6 Press
.
The SET indicator flashes three times and turns off.
7 Check if the code number works correctly (see “Remote Button
Descriptions”).
If you still cannot operate the device, repeat steps to search for another
code that works for most functions of your device.
Checking the manufacturer’s code you have set
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2 Enter 9 - 3 - 3 using the number buttons.
The SET indicator flashes three times.
3 Press à.
4 When the SET indicator starts flashing, count the number of flashes.
Short flash(es) indicate which digit (first, second, etc.), followed by long
flash(es) to indicate the digit number (i.e., 2 long flashes represent the
number 2). “0” is indicated by rapid flashing.
Determine the 5-digit code number this way. To recheck, press à.
5 Press SET to finish.
Clearing the automatic power-on control (Sony
devices only)
The Device Select buttons are preset to automatically turn on a device when
pressed.
To cancel the function:
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
, then release both buttons.
2 Enter 9 - 7 - 7 using the number buttons.
The SET indicator flashes three times.
3 Press the desired Device Select button.
The SET indicator flashes three times and turns off.
To set the function again, perform the same procedure above.
Restoring the factory settings
You can clear all the settings and reset the RM-VZ220 to its factory settings.
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
, then release both buttons.
2 Enter 9 - 0 - 0 using the number buttons.
The SET indicator flashes three times.
To cancel, press any button except
.
3 Press
.
The SET indicator flashes three times and turns off.
Remote Button Descriptions
General
ȩȪ
SET: Press to set up the RM-VZ220. The indicator lights or flashes while
setting.
ȫ
Device Select buttons: Press to select the device to operate.
Ȯ
GUIDE: Displays the program guide (EPG).
ȯ
j//V/p/
: Moves the cursor to select a menu item/enters the selected item.
ȱ
RETURN: Returns to the previous display/exits the menu.
ȳ
VOL +/–: Turns the volume up/down.
ȸ
POWER: Turns the selected device on and off.
Ⱦ
MUTING: Mutes the volume. Press again to turn muting off.
ɀ
SLEEP: Enables the Sleep function (when available).
The number 5, CH+, and à buttons each have a tactile dot for ease of use.
The GUIDE and RETURN buttons do not work for a VCR.
Note on the VOL+/– and MUTING buttons
When a TV or other video device is selected, the TV’s volume is controlled. When a
DVD Home Theater is selected, its volume can be controlled.
TV
Ȭ
Ã
: VIDEO 1 input
: VIDEO 2 input
: HDMI input
Ñ
: RGB input
ù
: (PIP INPUT) Changes the
input mode of the “window”
picture.
à
: (PIP) Turns the “window”
picture on and off.
ß
: (PIP MOVE) Moves the
location of the “window” picture.
ê
: (PIP STILL) Freezes the
“window” picture.
Ą
: (PIP SWAP) Switches between
“main” and “window” picture.
ȭ
A: Red button
B: Green button
C: Yellow button
D: Blue button
Ȱ
LIST: (CAPTION) Displays closed
captioning.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵȶɁ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: (PIP CH +/–) Changes
the channel up/down in the
“window” picture.
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: Selects the channel
previously selected.
ȿ
CH +/–: Switches the channel up/
down.
Cable set top box/IPTV
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A, B, C buttons
D: (Live TV) Displays Master
Guide.
Ȱ
LIST: Displays the title of recorded
program.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵ ȶ Ɂ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: Page up/down
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: Switches between the
current and previous channel.
ȿ
CH +/–: Switches the channel up/
down.
Satellite receiver
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: Red button
B: Green button
C: Yellow button
D: Blue button
Ȱ
LIST: Displays the title of recorded
program/PVR menu.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: (TV/SAT) Switches the
output between SAT and TV.
ȵ ȶ Ɂ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: Page up/down
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the Satellite
dish menu/Station Index.
Ƚ
RECALL: Tunes to the last tuned
station.
ȿ
CH +/–: Switches the channel up/
down.
VCR
Ȭ
ù
: Rewinds.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȷ
ì: Ejects a tape.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: (ANT/SW) Switches
the antenna output.
Ƚ
RECALL: (DRIVE SELECT) Selects
the deck.
ȿ
CH +/–: Switches the channel up/
down.
Ɂ
ENTER: Enters the selected item.
DVD player/recorder
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records (for DVD recorder).
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȱ
LIST: Displays the Title List.
Ȳ
MENU: Displays the DVD menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +: (DVD) Selects the DVD
drive.
PAGE –: (HDD) Selects the
internal HDD (hard disk drive).
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: (DRIVE SELECT)
Switches between HDD and DVD.
ȿ
CH +/–: Switches the channel up/
down (for DVD recorder).
Ɂ
ENTER: Enters the selected item.
Blu-ray Disc/HD-DVD player
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records (for BD recorder).
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȳ
MENU: Displays the Pop-up Menu/
Disc Menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +: (BD) Selects the BD drive.
PAGE –: (HDD) Selects the
internal HDD (hard disk drive).
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the options
menu.
Ɂ
ENTER: Enters the selected item.
DVR (digital video recorder)/PVR (personal video recorder)
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: (REPLAY*) Enables the Replay
function for DVR/Replay TV.
B: (Live TV*) Displays Master
Guide.
Ȱ
LIST: Displays the title of recorded
program.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +/–: Page up/down,
Thumbs* up/down
Ȼ
INFO: (DISPLAY) Displays the
playback information.
Ƚ
RECALL: Selects the channel
previously selected.
ȿ
CH +/–: Switches the channel up/
down.
Ɂ
ENTER: Enters the selected item.
* These buttons correspond to TiVo
service or the Replay service. Refer to
its instruction manual for details.
DVD Home Theater
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȱ
LIST: Enables the SOUND FIELD
function.
Ȳ
MENU: Displays the DVD menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the amplifier
menu.
Ƚ
RECALL: (BAND) Selects FM/AM.
ȿ
CH +/–: Presets or tunes frequency
up/down.
Ɂ
ENTER: Enters the selected item.
Notes on using the RM-VZ220
ˎ
The RM-VZ220 will not perform functions that the device is not designed for. For
example, if your TV does not have the muting function, MUTING on the RM-VZ220
will not function with your TV.
ˎ
The function of the buttons varies depending on settings/operating modes. The table
of “Remote Button Descriptions” shows how the RM-VZ220 generally operates for
each device in the preset mode.
ˎ
If your cable set top box can control volume, be sure to set its volume to a moderate
level. If the volume on the cable set top box is turned down completely, you will not be
able to adjust your TV’s volume with the RM-VZ220.
Manufacturer’s Code List /
Lista de códigos del fabricante
English
The following tables show brand names (Brand) and their corresponding
code numbers (Code No.).
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2 Enter the manufacturer’s code.
The SET indicator flashes three times and turns off.
Español
La siguiente tabla muestra los nombres de las marcas (Brand) y el número
de código correspondiente (Code No.).
1 Presione y mantenga presionado el botón SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras tiene presionado el botón SET, presione el botón de selección de
dispositivo deseado y luego suelte ambos botones.
2 Ingrese el código del fabricante.
El indicador SET parpadeará tres veces y se apagará.
Brand Code No.
Acer 01339
Action 00650
Admiral 00463
Akai 00812, 01675, 00702, 02232
Akira 01733
AOC 01365, 01589
Apex Digital 00748
Aventura 00171
Bell & Howell 00154
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Dynex 01463, 01810, 02049
Electroband 00000
Electrograph 01755
Electrohome 00463
Elektra 01661
Element 01687
Emerson 01864, 00154, 00463, 00171,
01661, 01394
Emprex 01765
Envision 01365, 01589
ESA 00812, 00171
Fisher 00154
Funai 00171
Gateway 01755, 01756
GE 01447, 00051, 02359
GFM 00171
Haier 01748, 01749, 02309, 02449
Harman/Kardon 00054
Hisense 00748, 01314, 02098
Hitachi 01643, 02215, 02433
iLo 01684
Infinity 00054
Insignia 01564, 00171, 02049
JBL 00054
JCB 00000
JVC 00731, 01253, 01601, 01774
KDS 01687
Kolin 01331
LG 01423, 02358
LXI 00054, 00154, 00156
MAG 01687
Magnavox 01454, 01866, 00054, 01254,
01365, 02372
Marantz 00054
Matsushita 00650
Maxent 01755
Memorex 00154, 00463, 00150
MGA 00150
Midland 00051
Brand Code No.
Mitsubishi 01250, 00150, 00836
NAD 00156
NEC 01797
NetTV 01755
Norcent 00748, 01365, 01589
Olevia 01610, 01144, 01331
Onida 01253, 02396
Optimus 00154, 00650
Orion 00463, 01463
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
Quasar 00051, 00650
RadioShack 00154
RCA 01447, 01781, 02187, 02247,
02403, 02429, 02434
Realistic 00154
Sampo 01755
Samsung 00812, 00702
Sansui 00463
Sanyo 00154, 01142
Sceptre 01360, 01599
Scott 01711
Sears 00054, 00154, 00156, 00171
Sharp 00818
Sony 00810, 00000
Spectroniq 01687
Squareview 00171
Superscan 00864
Supreme 00000
SVA 00748
Sylvania 01864, 00054, 00171, 01314,
01394
Symphonic 00171
Syntax 01610, 01144, 01331
Tatung 01756
TCL 02403, 02429
Technics 00051
Techwood 00051
Teknika 00054, 00150
Telefunken 00702
Toshiba 01524, 00154, 00156, 00650
TVS 00463
Venturer 01865
Videocon 01540, 01541, 02436
Vidikron 00054
Viewsonic 01755, 00864, 00885, 01627,
01742
Viore 01684, 02104, 02352
Vizio 01758, 00864, 00885, 01756
VU 02098
TV / TV
Brand Code No.
Wards 00054
Waycon 00156
Westinghouse 01712, 00885, 01577
White
Westinghouse
00463, 01661
Wyse 01365
Zenith 00463, 01661
Brand Code No.
Accurian 10675
Akai 10695
Allegro 10869
Apex Digital 10672, 11056
Bel Canto Design 11571
Broksonic 10695
CineVision 10869
Citizen 10695
CyberHome 11024
Daewoo 10869
Denon 10490, 11634, 12258
Disney 10675, 11270
Emerson 10591, 10675
Enterprise 10591
Funai 10675
GE 10522
GFM 10675
Go Video 10744, 10741, 10869, 11044,
11075
GoldStar 10741
Harman/Kardon 11229
Hitachi 10573, 10664
Hiteker 10672
Insignia 10675, 12428, 12596
Integra 11769, 10627, 12147
JVC 10623, 10867, 11164
Kenwood 10490
LG 10591, 10741, 10869
Magnavox 10503, 10539, 10646, 10675,
11354
Marantz 10539, 12414, 12432
Memorex 10695, 11270, 12213
Microsoft 10522, 12083
Mitsubishi 11521
NAD 10741, 12572
Olevia 12331
Onkyo 10503, 11769, 10627, 11627,
12147
Brand Code No.
Oppo 10575, 12545
Panasonic 10490, 11579, 11641
Philco 10675
Philips 10503, 10539, 12056, 12084,
10646, 10675, 11267, 11354,
12434
Pioneer 10142, 10631, 11571, 12442
Polk Audio 10539
Presidian 10675
Proscan 10522
RCA 10522, 11769, 10822, 12213,
12587, 12592, 12594
Rio 10869
Rotel 10623
Samsung 10490, 10573, 10199, 11044,
11075, 12329, 12489
Sansui 10695
Sanyo 10695
Sharp 10630, 10675, 12250
Shinsonic 10533
Sonic Blue 10869
Sony 11633, 10533, 10864, 11033,
11070, 11431, 11516
Sylvania 10675
Symphonic 10675
TCL 12587
Technics 10490
Tivo 11503
Toshiba 10503, 11769, 10695, 11154,
11503, 12006, 12277
Urban Concepts 10503
Viore 12553
Vizio 12563
Vtrek 12587
Xbox 10522, 12083
Yamaha 10490, 10539, 10497, 10817,
12298
Zenith 10503, 10591, 10741, 10869
DVD player / Reproductor de DVD
Brand Code No.
Accurian 10675
Apex Digital 11056
Funai 10675
Go Video 10741
JVC 11164
LG 10741
Magnavox 10646, 10675
Panasonic 10490, 11579
Philips 10646
Brand Code No.
Pioneer 10631
RCA 10522
Samsung 10490
Sharp 10675
Sony 11033, 11070, 11431
Sylvania 10675
Toshiba 12277
Zenith 10741
DVD recorder / Grabadora de DVD
Blu-ray Disc/HD-DVD player/
Reproductor de Blu-ray Disc/HD-DVD
Brand Code No.
Denon 12258
Insignia 10675, 12428, 12596
Integra 11769, 12147
LG 10741
Magnavox 10675
Marantz 12414, 12432
Microsoft 12083
NAD 12572
Olevia 12331
Onkyo 11769, 12147
Oppo 12545
Panasonic 11641
Brand Code No.
Philips 12084, 12434
Pioneer 10142, 12442
RCA 11769
Samsung 10199
Sharp 12250
Sony 11516
Sylvania 10675
Toshiba 11769
Viore 12553
Vizio 12563
Xbox 12083
Yamaha 12298
If your device is not listed, try the Search function (see “Searching for the correct code”).
2
Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
the desired Device Select button,
then release both buttons.
3
Enter the manufacturer’s code (01454).
The SET indicator flashes three times and
turns off.
Operate the device
1
Aim the RM-VZ220 directly at the device.
2
Press the Device Select button for the
device you want to operate.
3
Press POWER to turn on the device.
4
Press buttons on the RM-VZ220 to check that they function.
See “Remote Button Descriptions” for the functions of buttons for each device.
If the RM-VZ220 does not seem to be working…
Check that you have set the correct manufacturer’s code.
Try repeating the setup procedure using another manufacturer’s code (if listed for your device).
If you still cannot operate the RM-VZ220 after trying all the listed codes, try the Search function (see “Searching
for the correct code”).
Notes
If the setting is incomplete,
the SET indicator flashes once
and the indicators turn off.
Start again from the
beginning.
If no operations are
performed for 10 seconds
while setting, the setting will
be canceled, and must be
restarted.
To cancel the process, press
SET any time. The SET
indicator turns off.
SET
POWER
Device
Select
buttons
Number
buttons
The SET indicator
lights up.
Searching for the correct code
You can set the manufacturer’s code using the Search function.
1
Power on the device with its power switch.
2
Aim the RM-VZ220 at the device you want to set.
3
Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
4
Enter 9 - 2 - 2 using the number buttons.
The SET indicator flashes three times.
5
Press and hold to start searching.
When the device turns off, release the button.
If you overshoot the required code, you can search for the next or previous
code using the
or
button.
6
Press .
The SET indicator flashes three times and turns off.
7
Check if the code number works correctly (see “Remote Button
Descriptions”).
If you still cannot operate the device, repeat steps to search for another
code that works for most functions of your device.
Checking the manufacturer’s code you have set
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2
Enter 9 - 3 - 3 using the number buttons.
The SET indicator flashes three times.
3
Press .
4
When the SET indicator starts flashing, count the number of flashes.
Short flash(es) indicate which digit (first, second, etc.), followed by long
flash(es) to indicate the digit number (i.e., 2 long flashes represent the
number 2). “0” is indicated by rapid flashing.
Determine the 5-digit code number this way. To recheck, press .
5
Press SET to finish.
Clearing the automatic power-on control (Sony
devices only)
The Device Select buttons are preset to automatically turn on a device when
pressed.
To cancel the function:
1
Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press , then release both buttons.
2
Enter 9 - 7 - 7 using the number buttons.
The SET indicator flashes three times.
3
Press the desired Device Select button.
The SET indicator flashes three times and turns off.
To set the function again, perform the same procedure above.
Restoring the factory settings
You can clear all the settings and reset the RM-VZ220 to its factory settings.
1
Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press , then release both buttons.
2
Enter 9 - 0 - 0 using the number buttons.
The SET indicator flashes three times.
To cancel, press any button except .
3
Press .
The SET indicator flashes three times and turns off.
Remote Button Descriptions
General
SET: Press to set up the RM-VZ220. The indicator lights or flashes while
setting.
Device Select buttons: Press to select the device to operate.
GUIDE: Displays the program guide (EPG).
//// : Moves the cursor to select a menu item/enters the selected item.
RETURN: Returns to the previous display/exits the menu.
VOL +/–: Turns the volume up/down.
POWER: Turns the selected device on and off.
MUTING: Mutes the volume. Press again to turn muting off.
SLEEP: Enables the Sleep function (when available).
The number 5, CH+, and buttons each have a tactile dot for ease of use.
The GUIDE and RETURN buttons do not work for a VCR.
Note on the VOL+/– and MUTING buttons
When a TV or other video device is selected, the TV’s volume is controlled. When a
DVD Home Theater is selected, its volume can be controlled.
TV
: VIDEO 1 input
: VIDEO 2 input
: HDMI input
: RGB input
: (PIP INPUT) Changes the
input mode of the “window”
picture.
: (PIP) Turns the “window”
picture on and off.
: (PIP MOVE) Moves the
location of the “window” picture.
: (PIP STILL) Freezes the
“window” picture.
: (PIP SWAP) Switches between
“main” and “window” picture.
A: Red button
B: Green button
C: Yellow button
D: Blue button
LIST: (CAPTION) Displays closed
captioning.
MENU: Calls up the menu display.
INPUT: Changes the input mode.
1 – 9, 0, ENTER,
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
PAGE +/–: (PIP CH +/–) Changes
the channel up/down in the
“window” picture.
FAVORITES: Enables the Favorite
function.
INFO: Displays program
information.
OPTIONS: Displays the options
menu.
RECALL: Selects the channel
previously selected.
CH +/–: Switches the channel up/
down.
Cable set top box/IPTV
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
: Proceeds to the next location.
: Fast reverses.
: Plays.
: Fast forwards.
: Records.
: Pauses.
: Stops.
A, B, C buttons
D: (Live TV) Displays Master
Guide.
LIST: Displays the title of recorded
program.
MENU: Calls up the menu display.
INPUT: Changes the input mode.
1 – 9, 0, ENTER,
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
PAGE +/–: Page up/down
FAVORITES: Enables the Favorite
function.
INFO: Displays program
information.
OPTIONS: Displays the options
menu.
RECALL: Switches between the
current and previous channel.
CH +/–: Switches the channel up/
down.
Satellite receiver
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
: Proceeds to the next location.
: Fast reverses.
: Plays.
: Fast forwards.
: Records.
: Pauses.
: Stops.
A: Red button
B: Green button
C: Yellow button
D: Blue button
LIST: Displays the title of recorded
program/PVR menu.
MENU: Calls up the menu display.
INPUT: (TV/SAT) Switches the
output between SAT and TV.
1 – 9, 0, ENTER,
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
PAGE +/–: Page up/down
FAVORITES: Enables the Favorite
function.
INFO: Displays program
information.
OPTIONS: Displays the Satellite
dish menu/Station Index.
RECALL: Tunes to the last tuned
station.
CH +/–: Switches the channel up/
down.
VCR
: Rewinds.
: Plays.
: Fast forwards.
: Records.
: Pauses.
: Stops.
INPUT: Changes the input mode.
1 – 9, 0: Number buttons
: Ejects a tape.
INFO: (DISPLAY) Displays the
playback information.
OPTIONS: (ANT/SW) Switches
the antenna output.
RECALL: (DRIVE SELECT) Selects
the deck.
CH +/–: Switches the channel up/
down.
ENTER: Enters the selected item.
DVD player/recorder
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
: Skips to the next chapter/
track.
: Fast reverses.
: Plays.
: Fast forwards.
: Records (for DVD recorder).
: Pauses.
: Stops.
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
LIST: Displays the Title List.
MENU: Displays the DVD menu.
INPUT: Changes the input mode.
1 – 9, 0: Number buttons
(dot): (+10) Selects numbers 10
and above.
: Opens/closes the disc tray.
PAGE +: (DVD) Selects the DVD
drive.
PAGE –: (HDD) Selects the
internal HDD (hard disk drive).
FAVORITES: (TOP MENU)
Displays the Top Menu.
INFO: (DISPLAY) Displays the
playback information.
OPTIONS: Displays the options
menu.
RECALL: (DRIVE SELECT)
Switches between HDD and DVD.
CH +/–: Switches the channel up/
down (for DVD recorder).
ENTER: Enters the selected item.
Blu-ray Disc/HD-DVD player
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
: Skips to the next chapter/
track.
: Fast reverses.
: Plays.
: Fast forwards.
: Records (for BD recorder).
: Pauses.
: Stops.
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
MENU: Displays the Pop-up Menu/
Disc Menu.
INPUT: Changes the input mode.
1 – 9, 0: Number buttons
(dot): (+10) Selects numbers 10
and above.
: Opens/closes the disc tray.
PAGE +: (BD) Selects the BD drive.
PAGE –: (HDD) Selects the
internal HDD (hard disk drive).
FAVORITES: (TOP MENU)
Displays the Top Menu.
INFO: (DISPLAY) Displays the
playback information.
OPTIONS: Displays the options
menu.
ENTER: Enters the selected item.
DVR (digital video recorder)/PVR (personal video recorder)
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
: Proceeds to the next location.
: Fast reverses.
: Plays.
: Fast forwards.
: Records.
: Pauses.
: Stops.
A: (REPLAY*) Enables the Replay
function for DVR/Replay TV.
B: (Live TV*) Displays Master
Guide.
LIST: Displays the title of recorded
program.
MENU: Calls up the menu display.
INPUT: Changes the input mode.
1 – 9, 0: Number buttons
(dot): (+10) Selects numbers 10
and above.
: Opens/closes the disc tray.
PAGE +/–: Page up/down,
Thumbs* up/down
INFO: (DISPLAY) Displays the
playback information.
RECALL: Selects the channel
previously selected.
CH +/–: Switches the channel up/
down.
ENTER: Enters the selected item.
* These buttons correspond to TiVo
service or the Replay service. Refer to
its instruction manual for details.
DVD Home Theater
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
: Skips to the next chapter/
track.
: Fast reverses.
: Plays.
: Fast forwards.
: Records.
: Pauses.
: Stops.
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
LIST: Enables the SOUND FIELD
function.
MENU: Displays the DVD menu.
INPUT: Changes the input mode.
1 – 9, 0: Number buttons
(dot): (+10) Selects numbers 10
and above.
: Opens/closes the disc tray.
FAVORITES: (TOP MENU)
Displays the Top Menu.
INFO: (DISPLAY) Displays the
playback information.
OPTIONS: Displays the amplifier
menu.
RECALL: (BAND) Selects FM/AM.
CH +/–: Presets or tunes frequency
up/down.
ENTER: Enters the selected item.
Notes on using the RM-VZ220
The RM-VZ220 will not perform functions that the device is not designed for. For
example, if your TV does not have the muting function, MUTING on the RM-VZ220
will not function with your TV.
The function of the buttons varies depending on settings/operating modes. The table
of “Remote Button Descriptions” shows how the RM-VZ220 generally operates for
each device in the preset mode.
If your cable set top box can control volume, be sure to set its volume to a moderate
level. If the volume on the cable set top box is turned down completely, you will not be
able to adjust your TV’s volume with the RM-VZ220.
Manufacturer’s Code List /
Lista de códigos del fabricante
English
The following tables show brand names (Brand) and their corresponding
code numbers (Code No.).
1
Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2
Enter the manufacturer’s code.
The SET indicator flashes three times and turns off.
Español
La siguiente tabla muestra los nombres de las marcas (Brand) y el número
de código correspondiente (Code No.).
1
Presione y mantenga presionado el botón SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras tiene presionado el botón SET, presione el botón de selección de
dispositivo deseado y luego suelte ambos botones.
2
Ingrese el código del fabricante.
El indicador SET parpadeará tres veces y se apagará.
Brand Code No.
Acer 01339
Action 00650
Admiral 00463
Akai 00812, 01675, 00702, 02232
Akira 01733
AOC 01365, 01589
Apex Digital 00748
Aventura 00171
Bell & Howell 00154
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Dynex 01463, 01810, 02049
Electroband 00000
Electrograph 01755
Electrohome 00463
Elektra 01661
Element 01687
Emerson 01864, 00154, 00463, 00171,
01661, 01394
Emprex 01765
Envision 01365, 01589
ESA 00812, 00171
Fisher 00154
Funai 00171
Gateway 01755, 01756
GE 01447, 00051, 02359
GFM 00171
Haier 01748, 01749, 02309, 02449
Harman/Kardon 00054
Hisense 00748, 01314, 02098
Hitachi 01643, 02215, 02433
iLo 01684
Infinity 00054
Insignia 01564, 00171, 02049
JBL 00054
JCB 00000
JVC 00731, 01253, 01601, 01774
KDS 01687
Kolin 01331
LG 01423, 02358
LXI 00054, 00154, 00156
MAG 01687
Magnavox 01454, 01866, 00054, 01254,
01365, 02372
Marantz 00054
Matsushita 00650
Maxent 01755
Memorex 00154, 00463, 00150
MGA 00150
Midland 00051
Brand Code No.
Mitsubishi 01250, 00150, 00836
NAD 00156
NEC 01797
NetTV 01755
Norcent 00748, 01365, 01589
Olevia 01610, 01144, 01331
Onida 01253, 02396
Optimus 00154, 00650
Orion 00463, 01463
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
Quasar 00051, 00650
RadioShack 00154
RCA 01447, 01781, 02187, 02247,
02403, 02429, 02434
Realistic 00154
Sampo 01755
Samsung 00812, 00702
Sansui 00463
Sanyo 00154, 01142
Sceptre 01360, 01599
Scott 01711
Sears 00054, 00154, 00156, 00171
Sharp 00818
Sony 00810, 00000
Spectroniq 01687
Squareview 00171
Superscan 00864
Supreme 00000
SVA 00748
Sylvania 01864, 00054, 00171, 01314,
01394
Symphonic 00171
Syntax 01610, 01144, 01331
Tatung 01756
TCL 02403, 02429
Technics 00051
Techwood 00051
Teknika 00054, 00150
Telefunken 00702
Toshiba 01524, 00154, 00156, 00650
TVS 00463
Venturer 01865
Videocon 01540, 01541, 02436
Vidikron 00054
Viewsonic 01755, 00864, 00885, 01627,
01742
Viore 01684, 02104, 02352
Vizio 01758, 00864, 00885, 01756
VU 02098
TV / TV
Brand Code No.
Wards 00054
Waycon 00156
Westinghouse 01712, 00885, 01577
White
Westinghouse
00463, 01661
Wyse 01365
Zenith 00463, 01661
Brand Code No.
Accurian 10675
Akai 10695
Allegro 10869
Apex Digital 10672, 11056
Bel Canto Design 11571
Broksonic 10695
CineVision 10869
Citizen 10695
CyberHome 11024
Daewoo 10869
Denon 10490, 11634, 12258
Disney 10675, 11270
Emerson 10591, 10675
Enterprise 10591
Funai 10675
GE 10522
GFM 10675
Go Video 10744, 10741, 10869, 11044,
11075
GoldStar 10741
Harman/Kardon 11229
Hitachi 10573, 10664
Hiteker 10672
Insignia 10675, 12428, 12596
Integra 11769, 10627, 12147
JVC 10623, 10867, 11164
Kenwood 10490
LG 10591, 10741, 10869
Magnavox 10503, 10539, 10646, 10675,
11354
Marantz 10539, 12414, 12432
Memorex 10695, 11270, 12213
Microsoft 10522, 12083
Mitsubishi 11521
NAD 10741, 12572
Olevia 12331
Onkyo 10503, 11769, 10627, 11627,
12147
Brand Code No.
Oppo 10575, 12545
Panasonic 10490, 11579, 11641
Philco 10675
Philips 10503, 10539, 12056, 12084,
10646, 10675, 11267, 11354,
12434
Pioneer 10142, 10631, 11571, 12442
Polk Audio 10539
Presidian 10675
Proscan 10522
RCA 10522, 11769, 10822, 12213,
12587, 12592, 12594
Rio 10869
Rotel 10623
Samsung 10490, 10573, 10199, 11044,
11075, 12329, 12489
Sansui 10695
Sanyo 10695
Sharp 10630, 10675, 12250
Shinsonic 10533
Sonic Blue 10869
Sony 11633, 10533, 10864, 11033,
11070, 11431, 11516
Sylvania 10675
Symphonic 10675
TCL 12587
Technics 10490
Tivo 11503
Toshiba 10503, 11769, 10695, 11154,
11503, 12006, 12277
Urban Concepts 10503
Viore 12553
Vizio 12563
Vtrek 12587
Xbox 10522, 12083
Yamaha 10490, 10539, 10497, 10817,
12298
Zenith 10503, 10591, 10741, 10869
DVD player / Reproductor de DVD
Brand Code No.
Accurian 10675
Apex Digital 11056
Funai 10675
Go Video 10741
JVC 11164
LG 10741
Magnavox 10646, 10675
Panasonic 10490, 11579
Philips 10646
Brand Code No.
Pioneer 10631
RCA 10522
Samsung 10490
Sharp 10675
Sony 11033, 11070, 11431
Sylvania 10675
Toshiba 12277
Zenith 10741
DVD recorder / Grabadora de DVD
Blu-ray Disc/HD-DVD player/
Reproductor de Blu-ray Disc/HD-DVD
Brand Code No.
Denon 12258
Insignia 10675, 12428, 12596
Integra 11769, 12147
LG 10741
Magnavox 10675
Marantz 12414, 12432
Microsoft 12083
NAD 12572
Olevia 12331
Onkyo 11769, 12147
Oppo 12545
Panasonic 11641
Brand Code No.
Philips 12084, 12434
Pioneer 10142, 12442
RCA 11769
Samsung 10199
Sharp 12250
Sony 11516
Sylvania 10675
Toshiba 11769
Viore 12553
Vizio 12563
Xbox 12083
Yamaha 12298
Español
Para los clientes de EE. UU.
ADVERTENCIA
Este equipo ha sido probado y se ha encontrado que cumple con los límites para
dispositivos digitales de Clase B, de acuerdo con la Parte 15 de las normas de la FCC.
Estos límites han sido diseñados para proporcionar una protección razonable contra
interferencias perjudiciales en una instalación residencial.
Este equipo genera, usa y puede emitir energía de radiofrecuencia y, si no se instala y
utiliza de acuerdo con las instrucciones, puede provocar interferencias perjudiciales en
las radiocomunicaciones. Sin embargo, no existe ninguna garantía de que tales
interferencias no se produzcan en una instalación particular. Si este equipo llega a
producir interferencias dañinas en la recepción por radio o TV, lo que podrá
comprobarse encendiendo y apagando el aparato, se recomienda al usuario que intente
corregir la interferencia tocontrol remoto una o más de las siguientes medidas:
Reorientación o reubicación de la antena receptora.
Aumento de la separación entre el equipo y el receptor.
Conexión del equipo a un tomacorriente diferente del utilizado por el receptor.
Solicitud de ayuda al proveedor o a un técnico de radio/televisión experimentado.
Tenga en cuenta que cualquier cambio o modificación que no se apruebe expresamente
en este manual puede anular su derecho a utilizar este equipo.
Configuración del RM-VZ220
El RM-VZ220 está configurado de fábrica para funcionar con los
dispositivos de video de la marca Sony en cualquiera de los botones de
selección de dispositivos (consulte la tabla a continuación).
Para usar los dispositivos que no sean marca Sony, o dispositivos marca Sony
que no vengan configurados de fábrica, establezca el código del fabricante de
cada dispositivo.
Dispositivos Botón Configuración de
fábrica*
TV
TV
Televisor Sony (00810)
TV, decodificador de cable,
receptor de satéllite, IPTV,
reproductor de DVD, grabadora
de DVD, reproductor de Blu-ray
Disc, DVR (videograbadora
digital), PVR (videograbadora
personal), VCR, DVD con cine en
casa
CBL (SAT)
Decodificador de cable
(no de marca Sony)
(51376)
VCR
VCR Sony (60032)
DVD
Reproductor de DVD
Sony (11033)
* El código de cinco dígitos es el código establecido por el fabricante.
Nota
Solamente se puede asignar un TV al botón de selección de dispositivos del TV. Puede
asignar cualquier dispositivo a los otros botones de selección de dispositivos.
Instalación de las baterías
Abra el compartimiento de las baterías e inserte dos baterías tamaño AA
(R6) secas (no incluidas).
Inserte las baterías (primero el lado negativo) en el compartimiento tal como
se muestra abajo.
1 2
Vida útil de la batería
En condiciones normales, las baterías secas alcalinas AA (LR6) pueden
durar hasta un año. Si el RM-VZ220 no funciona apropiadamente, las
baterías pueden descargarse. Si ocurriera esto, reemplace ambas baterías con
un par nuevo.
Notas
Reemplace las baterías por nuevas dentro de los dos minutos, y no presione ningún
botón mientras las reemplaza. De hacerlo, se pueden borrar las configuraciones de los
códigos.
No usar una batería vieja con una nueva, ni usar diferentes tipos de baterías juntos.
Si se derraman los electrolitos contenidos dentro de la batería, limpie el área
contaminada del compartimiento de las baterías con un paño y reemplace las baterías
viejas con nuevas. Para evitar los derrames de electrolitos, quite las baterías si tiene
planeado no utilizar el RM-VZ220 durante un período de tiempo prolongado.
Especificaciones
Distancia de operación Aproximadamente 11 m (36 pies) (varía según los
dispositivos de los diferentes fabricantes)
Requisitos de alimentación
Dos baterías secas de tamaño AA (R6) (no incluidas)
Vida útil de la batería
Aproximadamente 1 año cuando se utilizan baterías alcalinas
de tamaño AA (LR6) (varía de acuerdo con la frecuencia del
uso de los botones, hasta un uso aproximado de 300 veces
por día.)
Dimensiones
Aproximadamente 53 × 213 × 27 mm
(2
1
/
8
× 8
1
/
2
× 1
1
/
8
pulgadas) (a × h × d)
Peso
Aproximadamente 100 g (3,5 onzas) (sin incluir las baterías)
El diseño y las especificaciones están sujetos a cambios sin previo aviso.
Solución de problemas
Si tiene problemas con la configuración o el funcionamiento del RM-VZ220:
Realice con cuidado el procedimiento de configuración de la “Guía de configuración”.
Si el RM-VZ220 no funciona, intente repetir el procedimiento de configuración con
otro código de fabricante (si hay otros en la enumeración de códigos de su
dispositivo). Si sigue sin poder operar el RM-VZ220, intente con la función Búsqueda
(consulte “Búsqueda del código del fabricante”).
Apunte el RM-VZ220 directamente al dispositivo.
Quite cualquier obstáculo en el camino entre el RM-VZ220 y el dispositivo.
Asegúrese de haber presionado el botón de selección de dispositivo correcto.
Controle que el dispositivo tenga capacidad para infrarrojo de control remoto. Por
ejemplo, si su dispositivo no incluía un control remoto, probablemente no sea capaz
de ser controlado por el RM-VZ220.
Las baterías están agotadas o no están insertadas correctamente. Reemplácelas por
nuevas o insértelas correctamente.
Para clientes en EE. UU.
Información de asistencia al cliente
Luego de leer este manual, si todavía no puede lograr que el RM-VZ220 funcione
apropiadamente, llame a la Línea de ayuda de asistencia al cliente de Sony
al 1-800-822-2217.
Guía de configuración
Esta guía muestra la configuración y uso del RM-VZ220 para operar sus dispositivos.
Si su dispositivo Sony ya ha sido configurado, consulte “Funcionamiento del dispositivo”.
Establezca el código del fabricante
Ejemplo: Para usar un televisor Philips
1
Encuentre el código del fabricante en la “Lista de códigos del fabricante”.
RM-VZ220_U [US,ES] 4-170-642-12(1)RM-VZ220_U [US,ES] 4-170-642-12(1)
4-170-642-12(1)
Remote Commander
RM-VZ220
©2010 Sony Corporation Printed in China
Operating Instructions
Manual de instrucciones (parte posterior)
English
For the Customers in the U.S.A.
WARNING
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
ˎ
Reorient or relocate the receiving antenna.
ˎ
Increase the separation between the equipment and receiver.
ˎ
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
ˎ
Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this
manual could void your authority to operate this equipment.
Setting Up the RM-VZ220
The RM-VZ220 is preset at the factory to operate Sony brand video devices
set to any of the Device Select buttons (see the table below).
To use with non-Sony devices, or Sony devices that are not preset at the
factory, set the manufacturer’s code for each device.
Devices Button Factory setting*
TV
TV
Sony TV (00810)
TV, Cable set top box, Satellite
receiver, IPTV, DVD player, DVD
recorder, Blu-ray Disc player, DVR
(digital video recorder), PVR
(personal video recorder), VCR,
DVD Home Theater
CBL (SAT)
Cable set top box (non-
Sony) (51376)
VCR
Sony VCR (60032)
DVD
Sony DVD player
(11033)
* The five-digit code is the preset manufacturer’s code.
Note
Only a TV can be assigned to the TV Device Select button. You can assign any device to
the other Device Select buttons.
Installing the batteries
Slide open the battery compartment and insert two size AA (R6) dry
batteries (not supplied).
Insert the batteries (negative end first) through the guide clamp within each
compartment as shown below.
1 2
Battery life
Under normal conditions, size AA (LR6) alkaline batteries will last up to one
year. If the RM-VZ220 does not operate properly, the batteries might be
drained. Replace both batteries with new ones.
Notes
ˎ
Replace the batteries within 2 minutes after removing them, and do not press any
button when replacing the batteries. Otherwise, your code settings may be cleared.
ˎ
Do not use an old battery with a new one, or mix different types of batteries together.
ˎ
If the electrolyte inside the battery should leak, wipe the contaminated area of the
battery compartment with a cloth and replace the old batteries with new ones. To
prevent electrolyte from leaking, remove the batteries when you plan not to use the
RM-VZ220 for a long period of time.
Specifications
Operating distance Approx. 11 m (36 ft) (varies depending on devices of
different manufacturers)
Power requirements Two size AA (R6) dry batteries (not supplied)
Battery life Approx. 1 year when using size AA (LR6) alkaline batteries
(varies depending on frequency of button use - up to approx.
300 times per day.)
Dimensions Approx. 53 × 213 × 27 mm (2
1
/
8
× 8
1
/
2
× 1
1
/
8
in.)
(w/h/d)
Mass Approx. 100 g (3.5 oz) (not including batteries)
Design and specifications are subject to change without notice.
Troubleshooting
If you have problems setting up or using the RM-VZ220:
ˎ
Carefully perform the setup procedure of “Startup Guide.” If the RM-VZ220 does not
work, try repeating the setup procedure using another manufacturer’s code (if listed
for your device). If you still cannot operate the RM-VZ220, try the Search function
(see “Searching for the correct code”).
ˎ
Aim the RM-VZ220 directly at the device.
ˎ
Remove any obstacles in the path between the RM-VZ220 and the device.
ˎ
Make sure you have pressed the correct Device Select button.
ˎ
Check that the device has infrared remote capability. For example, if your device did
not come with a remote control, it probably is not capable of being controlled by the
RM-VZ220.
ˎ
The batteries are weak, or not inserted correctly. Replace them with new ones or insert
them correctly.
For the customers in the U.S.A.
Customer Support Information
After you have read through this manual, if you still cannot get the RM-VZ220 to work
properly, call the Sony Customer Support Helpline at
1-800-822-2217.
Startup Guide
This guide shows you how to set up and use the RM-VZ220 to operate your devices.
If your Sony device has already been preset, see “Operate the device.”
Set the manufacturer’s code
Example: To set up a Philips TV
1
Find the manufacturer’s code in “Manufacturer’s Code List.”
Manufacturer’s Code List /
Lista de códigos del fabricante
English
The following tables show brand names (Brand) and their corresponding
code numbers (Code No.).
1Press and hold SET for more than 3 seconds.
TheSET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2Enter the manufacturer’s code.
TheSET indicator flashes three times and turns off.
Español
La siguiente tabla muestra los nombres de las marcas (Brand) y el número
de código correspondiente (Code No.).
1Presione y mantenga presionado el botón SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras tiene presionado el botón SET, presione el botón de selección de
dispositivo deseado y luego suelte ambos botones.
2Ingrese el código del fabricante.
El indicador SET parpadeará tres veces y se apagará.
Brand Code No.
Sony 00810, 00000
Acer 01339
Action 00650
Admiral 00463
Akai 00812, 01675, 00702, 02232
Akira 01733
AOC 01365, 01589
Apex Digital 00748
Aventura 00171
Bell & Howell 00154
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Dynex 01463, 01810, 02049
Electroband 00000
Electrograph 01755
Electrohome 00463
Elektra 01661
Element 01687
Emerson 01864, 00154, 00463, 00171,
01661, 01394
Emprex 01765
Envision 01365, 01589
ESA 00812, 00171
Fisher 00154
Funai 00171
Gateway 01755, 01756
GE 01447, 00051, 02359
GFM 00171
Haier 01748, 01749, 02309, 02449
Harman/Kardon00054
Hisense 00748, 01314, 02098
Hitachi 01643, 02215, 02433
iLo 01684
Infinity 00054
Insignia 01564, 00171, 02049
JBL 00054
JCB 00000
JVC 00731, 01253, 01601, 01774
KDS 01687
Kolin 01331
LG 01423, 02358
LXI 00054, 00154, 00156
MAG 01687
Magnavox 01454, 01866, 00054, 01254,
01365, 02372
Marantz 00054
Matsushita 00650
Maxent 01755
Memorex 00154, 00463, 00150
MGA 00150
Brand Code No.
Midland 00051
Mitsubishi 01250, 00150, 00836
NAD 00156
NEC 01797
NetTV 01755
Norcent 00748, 01365, 01589
Olevia 01610, 01144, 01331
Onida 01253, 02396
Optimus 00154, 00650
Orion 00463, 01463
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
Quasar 00051, 00650
RadioShack 00154
RCA 01447, 01781, 02187, 02247,
02403, 02429, 02434
Realistic 00154
Sampo 01755
Samsung 00812, 00702
Sansui 00463
Sanyo 00154, 01142
Sceptre 01360, 01599
Scott 01711
Sears 00054, 00154, 00156, 00171
Sharp 00818
Spectroniq 01687
Squareview 00171
Superscan 00864
Supreme 00000
SVA 00748
Sylvania 01864, 00054, 00171, 01314,
01394
Symphonic 00171
Syntax 01610, 01144, 01331
Tatung 01756
TCL 02403, 02429
Technics 00051
Techwood 00051
Teknika 00054, 00150
Telefunken 00702
Toshiba 01524, 00154, 00156, 00650
TVS 00463
Venturer 01865
Videocon 01540, 01541, 02436
Vidikron 00054
Viewsonic 01755, 00864, 00885, 01627,
01742
Viore 01684, 02104, 02352
Vizio 01758, 00864, 00885, 01756
VU 02098
TV / TV
Brand Code No.
Wards 00054
Waycon 00156
Westinghouse 01712, 00885, 01577
White
Westinghouse
00463, 01661
Wyse 01365
Zenith 00463, 01661
Brand Code No.
Sony 11633, 10533, 10864, 11033,
11070, 11431, 11516
Accurian 10675
Akai 10695
Allegro 10869
Apex Digital 10672, 11056
Bel Canto Design11571
Broksonic 10695
CineVision 10869
Citizen 10695
CyberHome 11024
Daewoo 10869
Denon 10490, 11634, 12258
Disney 10675, 11270
Emerson 10591, 10675
Enterprise 10591
Funai 10675
GE 10522
GFM 10675
Go Video 10744, 10741, 10869, 11044,
11075
GoldStar 10741
Harman/Kardon11229
Hitachi 10573, 10664
Hiteker 10672
Insignia 10675, 12428, 12596
Integra 11769, 10627, 12147
JVC 10623, 10867, 11164
Kenwood 10490
LG 10591, 10741, 10869
Magnavox 10503, 10539, 10646, 10675,
11354
Marantz 10539, 12414, 12432
Memorex 10695, 11270, 12213
Microsoft 10522, 12083
Mitsubishi 11521
NAD 10741, 12572
Olevia 12331
Brand Code No.
Onkyo 10503, 11769, 10627, 11627,
12147
Oppo 10575, 12545
Panasonic 10490, 11579, 11641
Philco 10675
Philips 10503, 10539, 12056, 12084,
10646, 10675, 11267, 11354,
12434
Pioneer 10142, 10631, 11571, 12442
Polk Audio 10539
Presidian 10675
Proscan 10522
RCA 10522, 11769, 10822, 12213,
12587, 12592, 12594
Rio 10869
Rotel 10623
Samsung 10490, 10573, 10199, 11044,
11075, 12329, 12489
Sansui 10695
Sanyo 10695
Sharp 10630, 10675, 12250
Shinsonic 10533
Sonic Blue 10869
Sylvania 10675
Symphonic 10675
TCL 12587
Technics 10490
Tivo 11503
Toshiba 10503, 11769, 10695, 11154,
11503, 12006, 12277
Urban Concepts 10503
Viore 12553
Vizio 12563
Vtrek 12587
Xbox 10522, 12083
Yamaha 10490, 10539, 10497, 10817,
12298
Zenith 10503, 10591, 10741, 10869
DVD player / Reproductor de DVD
Brand Code No.
Sony 11033, 11070, 11431
Accurian 10675
Apex Digital 11056
Funai 10675
Go Video 10741
JVC 11164
LG 10741
Magnavox 10646, 10675
Panasonic 10490, 11579
Brand Code No.
Philips 10646
Pioneer 10631
RCA 10522
Samsung 10490
Sharp 10675
Sylvania 10675
Toshiba 12277
Zenith 10741
DVD recorder / Grabadora de DVD
Blu-ray Disc/HD-DVD player/
Reproductor de Blu-ray Disc/HD-DVD
Brand Code No.
Sony 11516
Denon 12258
Insignia 10675, 12428, 12596
Integra 11769, 12147
LG 10741
Magnavox 10675
Marantz 12414, 12432
Microsoft 12083
NAD 12572
Olevia 12331
Onkyo 11769, 12147
Oppo 12545
Brand Code No.
Panasonic 11641
Philips 12084, 12434
Pioneer 10142, 12442
RCA 11769
Samsung 10199
Sharp 12250
Sylvania 10675
Toshiba 11769
Viore 12553
Vizio 12563
Xbox 12083
Yamaha 12298
Brand Code No.
Sony 00810, 00000
Acer 01339
Action 00650
Brand Code No.
Midland 00051
Mitsubishi 01250, 00150, 00836
NAD 00156
TV / TV
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
If your device is not listed, try the Search function (see “Searching for the correct code”).
2
Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
the desired Device Select button,
then release both buttons.
3
Enter the manufacturer’s code (01454).
The SET indicator flashes three times and
turns off.
Operate the device
1
Aim the RM-VZ220 directly at the device.
2
Press the Device Select button for the
device you want to operate.
3
Press POWER to turn on the device.
4
Press buttons on the RM-VZ220 to check that they function.
See “Remote Button Descriptions” for the functions of buttons for each device.
If the RM-VZ220 does not seem to be working…
ˎ
Check that you have set the correct manufacturer’s code.
ˎ
Try repeating the setup procedure using another manufacturer’s code (if listed for your device).
If you still cannot operate the RM-VZ220 after trying all the listed codes, try the Search function (see “Searching
for the correct code”).
Notes
ˎ
If the setting is incomplete,
the SET indicator flashes once
and the indicators turn off.
Start again from the
beginning.
ˎ
If no operations are
performed for 10 seconds
while setting, the setting will
be canceled, and must be
restarted.
ˎ
To cancel the process, press
SET any time. The SET
indicator turns off.
SET
POWER
Device
Select
buttons
Number
buttons
The SET indicator
lights up.
Searching for the correct code
You can set the manufacturer’s code using the Search function.
1 Power on the device with its power switch.
2 Aim the RM-VZ220 at the device you want to set.
3 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
4 Enter 9 - 2 - 2 using the number buttons.
The SET indicator flashes three times.
5 Press and hold à to start searching.
When the device turns off, release the button.
If you overshoot the required code, you can search for the next or previous
code using the
ß
or
ù
button.
6 Press .
The SET indicator flashes three times and turns off.
7 Check if the code number works correctly (see “Remote Button
Descriptions”).
If you still cannot operate the device, repeat steps to search for another
code that works for most functions of your device.
Checking the manufacturer’s code you have set
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2 Enter 9 - 3 - 3 using the number buttons.
The SET indicator flashes three times.
3 Press à.
4 When the SET indicator starts flashing, count the number of flashes.
Short flash(es) indicate which digit (first, second, etc.), followed by long
flash(es) to indicate the digit number (i.e., 2 long flashes represent the
number 2). “0” is indicated by rapid flashing.
Determine the 5-digit code number this way. To recheck, press à.
5 Press SET to finish.
Clearing the automatic power-on control (Sony
devices only)
The Device Select buttons are preset to automatically turn on a device when
pressed.
To cancel the function:
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
, then release both buttons.
2 Enter 9 - 7 - 7 using the number buttons.
The SET indicator flashes three times.
3 Press the desired Device Select button.
The SET indicator flashes three times and turns off.
To set the function again, perform the same procedure above.
Restoring the factory settings
You can clear all the settings and reset the RM-VZ220 to its factory settings.
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press , then release both buttons.
2 Enter 9 - 0 - 0 using the number buttons.
The SET indicator flashes three times.
To cancel, press any button except .
3 Press
.
The SET indicator flashes three times and turns off.
Remote Button Descriptions
General
ȩȪ
SET: Press to set up the RM-VZ220. The indicator lights or flashes while
setting.
ȫ
Device Select buttons: Press to select the device to operate.
Ȯ
GUIDE: Displays the program guide (EPG).
ȯ
j//V/p/
: Moves the cursor to select a menu item/enters the selected item.
ȱ
RETURN: Returns to the previous display/exits the menu.
ȳ
VOL +/–: Turns the volume up/down.
ȸ
POWER: Turns the selected device on and off.
Ⱦ
MUTING: Mutes the volume. Press again to turn muting off.
ɀ
SLEEP: Enables the Sleep function (when available).
The number 5,CH+, and à buttons each have a tactile dot for ease of use.
TheGUIDE and RETURN buttons do not work for a VCR.
Note on the VOL+/– and MUTING buttons
When a TV or other video device is selected, the TV’s volume is controlled. When a
DVD Home Theater is selected, its volume can be controlled.
TV
Ȭ
Ã
: VIDEO 1 input
: VIDEO 2 input
: HDMI input
Ñ
: RGB input
ù
: (PIP INPUT) Changes the
input mode of the “window”
picture.
à
: (PIP) Turns the “window”
picture on and off.
ß
: (PIP MOVE) Moves the
location of the “window” picture.
ê
: (PIP STILL) Freezes the
“window” picture.
Ą
: (PIP SWAP) Switches between
“main” and “window” picture.
ȭ
A: Red button
B: Green button
C: Yellow button
D: Blue button
Ȱ
LIST: (CAPTION) Displays closed
captioning.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵȶɁ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: (PIP CH +/–) Changes
the channel up/down in the
“window” picture.
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: Selects the channel
previously selected.
ȿ
CH +/–: Switches the channel up/
down.
Cable set top box/IPTV
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A, B, C buttons
D: (Live TV) Displays Master
Guide.
Ȱ
LIST: Displays the title of recorded
program.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵȶ Ɂ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: Page up/down
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: Switches between the
current and previous channel.
ȿ
CH +/–: Switches the channel up/
down.
Satellite receiver
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: Red button
B: Green button
C: Yellow button
D: Blue button
Ȱ
LIST: Displays the title of recorded
program/PVR menu.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: (TV/SAT) Switches the
output between SAT and TV.
ȵȶ Ɂ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: Page up/down
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the Satellite
dish menu/Station Index.
Ƚ
RECALL: Tunes to the last tuned
station.
ȿ
CH +/–: Switches the channel up/
down.
VCR
Ȭ
ù
: Rewinds.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȷ
ì: Ejects a tape.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: (ANT/SW) Switches
the antenna output.
Ƚ
RECALL: (DRIVE SELECT) Selects
the deck.
ȿ
CH +/–: Switches the channel up/
down.
Ɂ
ENTER: Enters the selected item.
DVD player/recorder
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records (for DVD recorder).
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȱ
LIST: Displays the Title List.
Ȳ
MENU: Displays the DVD menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +: (DVD) Selects the DVD
drive.
PAGE –: (HDD) Selects the
internal HDD (hard disk drive).
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: (DRIVE SELECT)
Switches between HDD and DVD.
ȿ
CH +/–: Switches the channel up/
down (for DVD recorder).
Ɂ
ENTER: Enters the selected item.
Blu-ray Disc/HD-DVD player
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records (for BD recorder).
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȳ
MENU: Displays the Pop-up Menu/
Disc Menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +: (BD) Selects the BD drive.
PAGE –: (HDD) Selects the
internal HDD (hard disk drive).
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the options
menu.
Ɂ
ENTER: Enters the selected item.
DVR (digital video recorder)/PVR (personal video recorder)
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: (REPLAY*) Enables the Replay
function for DVR/Replay TV.
B: (Live TV*) Displays Master
Guide.
Ȱ
LIST: Displays the title of recorded
program.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +/–: Page up/down,
Thumbs* up/down
Ȼ
INFO: (DISPLAY) Displays the
playback information.
Ƚ
RECALL: Selects the channel
previously selected.
ȿ
CH +/–: Switches the channel up/
down.
Ɂ
ENTER: Enters the selected item.
* These buttons correspond to TiVo
service or the Replay service. Refer to
its instruction manual for details.
DVD Home Theater
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȱ
LIST: Enables the SOUND FIELD
function.
Ȳ
MENU: Displays the DVD menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the amplifier
menu.
Ƚ
RECALL: (BAND) Selects FM/AM.
ȿ
CH +/–: Presets or tunes frequency
up/down.
Ɂ
ENTER: Enters the selected item.
Notes on using the RM-VZ220
ˎ
The RM-VZ220 will not perform functions that the device is not designed for. For
example, if your TV does not have the muting function, MUTING on the RM-VZ220
will not function with your TV.
ˎ
The function of the buttons varies depending on settings/operating modes. The table
of “Remote Button Descriptions” shows how the RM-VZ220 generally operates for
each device in the preset mode.
ˎ
If your cable set top box can control volume, be sure to set its volume to a moderate
level. If the volume on the cable set top box is turned down completely, you will not be
able to adjust your TV’s volume with the RM-VZ220.
Manufacturer’s Code List /
Lista de códigos del fabricante
English
The following tables show brand names (Brand) and their corresponding
code numbers (Code No.).
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2 Enter the manufacturer’s code.
The SET indicator flashes three times and turns off.
Español
La siguiente tabla muestra los nombres de las marcas (Brand) y el número
de código correspondiente (Code No.).
1 Presione y mantenga presionado el botón SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras tiene presionado el botón SET, presione el botón de selección de
dispositivo deseado y luego suelte ambos botones.
2 Ingrese el código del fabricante.
El indicador SET parpadeará tres veces y se apagará.
Brand Code No.
Acer 01339
Action 00650
Admiral 00463
Akai 00812, 01675, 00702, 02232
Akira 01733
AOC 01365, 01589
Apex Digital 00748
Aventura 00171
Bell & Howell 00154
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Dynex 01463, 01810, 02049
Electroband 00000
Electrograph 01755
Electrohome 00463
Elektra 01661
Element 01687
Emerson 01864, 00154, 00463, 00171,
01661, 01394
Emprex 01765
Envision 01365, 01589
ESA 00812, 00171
Fisher 00154
Funai 00171
Gateway 01755, 01756
GE 01447, 00051, 02359
GFM 00171
Haier 01748, 01749, 02309, 02449
Harman/Kardon 00054
Hisense 00748, 01314, 02098
Hitachi 01643, 02215, 02433
iLo 01684
Infinity 00054
Insignia 01564, 00171, 02049
JBL 00054
JCB 00000
JVC 00731, 01253, 01601, 01774
KDS 01687
Kolin 01331
LG 01423, 02358
LXI 00054, 00154, 00156
MAG 01687
Magnavox 01454, 01866, 00054, 01254,
01365, 02372
Marantz 00054
Matsushita 00650
Maxent 01755
Memorex 00154, 00463, 00150
MGA 00150
Midland 00051
Brand Code No.
Mitsubishi 01250, 00150, 00836
NAD 00156
NEC 01797
NetTV 01755
Norcent 00748, 01365, 01589
Olevia 01610, 01144, 01331
Onida 01253, 02396
Optimus 00154, 00650
Orion 00463, 01463
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
Quasar 00051, 00650
RadioShack 00154
RCA 01447, 01781, 02187, 02247,
02403, 02429, 02434
Realistic 00154
Sampo 01755
Samsung 00812, 00702
Sansui 00463
Sanyo 00154, 01142
Sceptre 01360, 01599
Scott 01711
Sears 00054, 00154, 00156, 00171
Sharp 00818
Sony 00810, 00000
Spectroniq 01687
Squareview 00171
Superscan 00864
Supreme 00000
SVA 00748
Sylvania 01864, 00054, 00171, 01314,
01394
Symphonic 00171
Syntax 01610, 01144, 01331
Tatung 01756
TCL 02403, 02429
Technics 00051
Techwood 00051
Teknika 00054, 00150
Telefunken 00702
Toshiba 01524, 00154, 00156, 00650
TVS 00463
Venturer 01865
Videocon 01540, 01541, 02436
Vidikron 00054
Viewsonic 01755, 00864, 00885, 01627,
01742
Viore 01684, 02104, 02352
Vizio 01758, 00864, 00885, 01756
VU 02098
TV / TV
Brand Code No.
Wards 00054
Waycon 00156
Westinghouse 01712, 00885, 01577
White
Westinghouse
00463, 01661
Wyse 01365
Zenith 00463, 01661
Brand Code No.
Accurian 10675
Akai 10695
Allegro 10869
Apex Digital 10672, 11056
Bel Canto Design 11571
Broksonic 10695
CineVision 10869
Citizen 10695
CyberHome 11024
Daewoo 10869
Denon 10490, 11634, 12258
Disney 10675, 11270
Emerson 10591, 10675
Enterprise 10591
Funai 10675
GE 10522
GFM 10675
Go Video 10744, 10741, 10869, 11044,
11075
GoldStar 10741
Harman/Kardon 11229
Hitachi 10573, 10664
Hiteker 10672
Insignia 10675, 12428, 12596
Integra 11769, 10627, 12147
JVC 10623, 10867, 11164
Kenwood 10490
LG 10591, 10741, 10869
Magnavox 10503, 10539, 10646, 10675,
11354
Marantz 10539, 12414, 12432
Memorex 10695, 11270, 12213
Microsoft 10522, 12083
Mitsubishi 11521
NAD 10741, 12572
Olevia 12331
Onkyo 10503, 11769, 10627, 11627,
12147
Brand Code No.
Oppo 10575, 12545
Panasonic 10490, 11579, 11641
Philco 10675
Philips 10503, 10539, 12056, 12084,
10646, 10675, 11267, 11354,
12434
Pioneer 10142, 10631, 11571, 12442
Polk Audio 10539
Presidian 10675
Proscan 10522
RCA 10522, 11769, 10822, 12213,
12587, 12592, 12594
Rio 10869
Rotel 10623
Samsung 10490, 10573, 10199, 11044,
11075, 12329, 12489
Sansui 10695
Sanyo 10695
Sharp 10630, 10675, 12250
Shinsonic 10533
Sonic Blue 10869
Sony 11633, 10533, 10864, 11033,
11070, 11431, 11516
Sylvania 10675
Symphonic 10675
TCL 12587
Technics 10490
Tivo 11503
Toshiba 10503, 11769, 10695, 11154,
11503, 12006, 12277
Urban Concepts 10503
Viore 12553
Vizio 12563
Vtrek 12587
Xbox 10522, 12083
Yamaha 10490, 10539, 10497, 10817,
12298
Zenith 10503, 10591, 10741, 10869
DVD player / Reproductor de DVD
Brand Code No.
Accurian 10675
Apex Digital 11056
Funai 10675
Go Video 10741
JVC 11164
LG 10741
Magnavox 10646, 10675
Panasonic 10490, 11579
Philips 10646
Brand Code No.
Pioneer 10631
RCA 10522
Samsung 10490
Sharp 10675
Sony 11033, 11070, 11431
Sylvania 10675
Toshiba 12277
Zenith 10741
DVD recorder / Grabadora de DVD
Blu-ray Disc/HD-DVD player/
Reproductor de Blu-ray Disc/HD-DVD
Brand Code No.
Denon 12258
Insignia 10675, 12428, 12596
Integra 11769, 12147
LG 10741
Magnavox 10675
Marantz 12414, 12432
Microsoft 12083
NAD 12572
Olevia 12331
Onkyo 11769, 12147
Oppo 12545
Panasonic 11641
Brand Code No.
Philips 12084, 12434
Pioneer 10142, 12442
RCA 11769
Samsung 10199
Sharp 12250
Sony 11516
Sylvania 10675
Toshiba 11769
Viore 12553
Vizio 12563
Xbox 12083
Yamaha 12298
RM-VZ220_U [US,ES] 4-170-642-12(1)RM-VZ220_U [US,ES] 4-170-642-12(1)
4-170-642-12(1)
Remote Commander
RM-VZ220
©2010 Sony Corporation Printed in China
Operating Instructions
Manual de instrucciones (parte posterior)
English
For the Customers in the U.S.A.
WARNING
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
ˎ
Reorient or relocate the receiving antenna.
ˎ
Increase the separation between the equipment and receiver.
ˎ
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
ˎ
Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this
manual could void your authority to operate this equipment.
Setting Up the RM-VZ220
The RM-VZ220 is preset at the factory to operate Sony brand video devices
set to any of the Device Select buttons (see the table below).
To use with non-Sony devices, or Sony devices that are not preset at the
factory, set the manufacturer’s code for each device.
Devices Button Factory setting*
TV
TV
Sony TV (00810)
TV, Cable set top box, Satellite
receiver, IPTV, DVD player, DVD
recorder, Blu-ray Disc player, DVR
(digital video recorder), PVR
(personal video recorder), VCR,
DVD Home Theater
CBL (SAT)
Cable set top box (non-
Sony) (51376)
VCR
Sony VCR (60032)
DVD
Sony DVD player
(11033)
* The five-digit code is the preset manufacturer’s code.
Note
Only a TV can be assigned to the TV Device Select button. You can assign any device to
the other Device Select buttons.
Installing the batteries
Slide open the battery compartment and insert two size AA (R6) dry
batteries (not supplied).
Insert the batteries (negative end first) through the guide clamp within each
compartment as shown below.
1 2
Battery life
Under normal conditions, size AA (LR6) alkaline batteries will last up to one
year. If the RM-VZ220 does not operate properly, the batteries might be
drained. Replace both batteries with new ones.
Notes
ˎ
Replace the batteries within 2 minutes after removing them, and do not press any
button when replacing the batteries. Otherwise, your code settings may be cleared.
ˎ
Do not use an old battery with a new one, or mix different types of batteries together.
ˎ
If the electrolyte inside the battery should leak, wipe the contaminated area of the
battery compartment with a cloth and replace the old batteries with new ones. To
prevent electrolyte from leaking, remove the batteries when you plan not to use the
RM-VZ220 for a long period of time.
Specifications
Operating distance Approx. 11 m (36 ft) (varies depending on devices of
different manufacturers)
Power requirements Two size AA (R6) dry batteries (not supplied)
Battery life Approx. 1 year when using size AA (LR6) alkaline batteries
(varies depending on frequency of button use - up to approx.
300 times per day.)
Dimensions Approx. 53 × 213 × 27 mm (2
1
/
8
× 8
1
/
2
× 1
1
/
8
in.)
(w/h/d)
Mass Approx. 100 g (3.5 oz) (not including batteries)
Design and specifications are subject to change without notice.
Troubleshooting
If you have problems setting up or using the RM-VZ220:
ˎ
Carefully perform the setup procedure of “Startup Guide.” If the RM-VZ220 does not
work, try repeating the setup procedure using another manufacturer’s code (if listed
for your device). If you still cannot operate the RM-VZ220, try the Search function
(see “Searching for the correct code”).
ˎ
Aim the RM-VZ220 directly at the device.
ˎ
Remove any obstacles in the path between the RM-VZ220 and the device.
ˎ
Make sure you have pressed the correct Device Select button.
ˎ
Check that the device has infrared remote capability. For example, if your device did
not come with a remote control, it probably is not capable of being controlled by the
RM-VZ220.
ˎ
The batteries are weak, or not inserted correctly. Replace them with new ones or insert
them correctly.
For the customers in the U.S.A.
Customer Support Information
After you have read through this manual, if you still cannot get the RM-VZ220 to work
properly, call the Sony Customer Support Helpline at
1-800-822-2217.
Startup Guide
This guide shows you how to set up and use the RM-VZ220 to operate your devices.
If your Sony device has already been preset, see “Operate the device.”
Set the manufacturer’s code
Example: To set up a Philips TV
1
Find the manufacturer’s code in “Manufacturer’s Code List.”
Manufacturer’s Code List /
Lista de códigos del fabricante
English
The following tables show brand names (Brand) and their corresponding
code numbers (Code No.).
1 Press and hold SET for more than 3 seconds.
TheSET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2 Enter the manufacturer’s code.
TheSET indicator flashes three times and turns off.
Español
La siguiente tabla muestra los nombres de las marcas (Brand) y el número
de código correspondiente (Code No.).
1 Presione y mantenga presionado el botón SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras tiene presionado el botón SET, presione el botón de selección de
dispositivo deseado y luego suelte ambos botones.
2 Ingrese el código del fabricante.
El indicador SET parpadeará tres veces y se apagará.
Brand Code No.
Sony 00810, 00000
Acer 01339
Action 00650
Admiral 00463
Akai 00812, 01675, 00702, 02232
Akira 01733
AOC 01365, 01589
Apex Digital 00748
Aventura 00171
Bell & Howell 00154
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Dynex 01463, 01810, 02049
Electroband 00000
Electrograph 01755
Electrohome 00463
Elektra 01661
Element 01687
Emerson 01864, 00154, 00463, 00171,
01661, 01394
Emprex 01765
Envision 01365, 01589
ESA 00812, 00171
Fisher 00154
Funai 00171
Gateway 01755, 01756
GE 01447, 00051, 02359
GFM 00171
Haier 01748, 01749, 02309, 02449
Harman/Kardon 00054
Hisense 00748, 01314, 02098
Hitachi 01643, 02215, 02433
iLo 01684
Infinity 00054
Insignia 01564, 00171, 02049
JBL 00054
JCB 00000
JVC 00731, 01253, 01601, 01774
KDS 01687
Kolin 01331
LG 01423, 02358
LXI 00054, 00154, 00156
MAG 01687
Magnavox 01454, 01866, 00054, 01254,
01365, 02372
Marantz 00054
Matsushita 00650
Maxent 01755
Memorex 00154, 00463, 00150
MGA 00150
Brand Code No.
Midland 00051
Mitsubishi 01250, 00150, 00836
NAD 00156
NEC 01797
NetTV 01755
Norcent 00748, 01365, 01589
Olevia 01610, 01144, 01331
Onida 01253, 02396
Optimus 00154, 00650
Orion 00463, 01463
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
Quasar 00051, 00650
RadioShack 00154
RCA 01447, 01781, 02187, 02247,
02403, 02429, 02434
Realistic 00154
Sampo 01755
Samsung 00812, 00702
Sansui 00463
Sanyo 00154, 01142
Sceptre 01360, 01599
Scott 01711
Sears 00054, 00154, 00156, 00171
Sharp 00818
Spectroniq 01687
Squareview 00171
Superscan 00864
Supreme 00000
SVA 00748
Sylvania 01864, 00054, 00171, 01314,
01394
Symphonic 00171
Syntax 01610, 01144, 01331
Tatung 01756
TCL 02403, 02429
Technics 00051
Techwood 00051
Teknika 00054, 00150
Telefunken 00702
Toshiba 01524, 00154, 00156, 00650
TVS 00463
Venturer 01865
Videocon 01540, 01541, 02436
Vidikron 00054
Viewsonic 01755, 00864, 00885, 01627,
01742
Viore 01684, 02104, 02352
Vizio 01758, 00864, 00885, 01756
VU 02098
TV / TV
Brand Code No.
Wards 00054
Waycon 00156
Westinghouse 01712, 00885, 01577
White
Westinghouse
00463, 01661
Wyse 01365
Zenith 00463, 01661
Brand Code No.
Sony 11633, 10533, 10864, 11033,
11070, 11431, 11516
Accurian 10675
Akai 10695
Allegro 10869
Apex Digital 10672, 11056
Bel Canto Design 11571
Broksonic 10695
CineVision 10869
Citizen 10695
CyberHome 11024
Daewoo 10869
Denon 10490, 11634, 12258
Disney 10675, 11270
Emerson 10591, 10675
Enterprise 10591
Funai 10675
GE 10522
GFM 10675
Go Video 10744, 10741, 10869, 11044,
11075
GoldStar 10741
Harman/Kardon 11229
Hitachi 10573, 10664
Hiteker 10672
Insignia 10675, 12428, 12596
Integra 11769, 10627, 12147
JVC 10623, 10867, 11164
Kenwood 10490
LG 10591, 10741, 10869
Magnavox 10503, 10539, 10646, 10675,
11354
Marantz 10539, 12414, 12432
Memorex 10695, 11270, 12213
Microsoft 10522, 12083
Mitsubishi 11521
NAD 10741, 12572
Olevia 12331
Brand Code No.
Onkyo 10503, 11769, 10627, 11627,
12147
Oppo 10575, 12545
Panasonic 10490, 11579, 11641
Philco 10675
Philips 10503, 10539, 12056, 12084,
10646, 10675, 11267, 11354,
12434
Pioneer 10142, 10631, 11571, 12442
Polk Audio 10539
Presidian 10675
Proscan 10522
RCA 10522, 11769, 10822, 12213,
12587, 12592, 12594
Rio 10869
Rotel 10623
Samsung 10490, 10573, 10199, 11044,
11075, 12329, 12489
Sansui 10695
Sanyo 10695
Sharp 10630, 10675, 12250
Shinsonic 10533
Sonic Blue 10869
Sylvania 10675
Symphonic 10675
TCL 12587
Technics 10490
Tivo 11503
Toshiba 10503, 11769, 10695, 11154,
11503, 12006, 12277
Urban Concepts 10503
Viore 12553
Vizio 12563
Vtrek 12587
Xbox 10522, 12083
Yamaha 10490, 10539, 10497, 10817,
12298
Zenith 10503, 10591, 10741, 10869
DVD player / Reproductor de DVD
Brand Code No.
Sony 11033, 11070, 11431
Accurian 10675
Apex Digital 11056
Funai 10675
Go Video 10741
JVC 11164
LG 10741
Magnavox 10646, 10675
Panasonic 10490, 11579
Brand Code No.
Philips 10646
Pioneer 106 31
RCA 10522
Samsung 10490
Sharp 10675
Sylvania 10675
Toshiba 12277
Zenith 10741
DVD recorder / Grabadora de DVD
Blu-ray Disc/HD-DVD player/
Reproductor de Blu-ray Disc/HD-DVD
Brand Code No.
Sony 11516
Denon 12258
Insignia 10675, 12428, 12596
Integra 11769, 12147
LG 10741
Magnavox 10675
Marantz 12414, 12432
Microsoft 12083
NAD 12572
Olevia 12331
Onkyo 11769, 12147
Oppo 12545
Brand Code No.
Panasonic 11641
Philips 12084, 12434
Pioneer 10142, 12442
RCA 11769
Samsung 10199
Sharp 12250
Sylvania 10675
Toshiba 11769
Viore 12553
Vizio 12563
Xbox 12083
Yamaha 12298
Brand Code No.
Sony 00810, 00000
Acer 01339
Action 00650
Brand Code No.
Midland 00051
Mitsubishi 01250, 00150, 00836
NAD 00156
TV / TV
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
If your device is not listed, try the Search function (see “Searching for the correct code”).
2
Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
the desired Device Select button,
then release both buttons.
3
Enter the manufacturer’s code (01454).
The SET indicator flashes three times and
turns off.
Operate the device
1
Aim the RM-VZ220 directly at the device.
2
Press the Device Select button for the
device you want to operate.
3
Press POWER to turn on the device.
4
Press buttons on the RM-VZ220 to check that they function.
See “Remote Button Descriptions” for the functions of buttons for each device.
If the RM-VZ220 does not seem to be working…
ˎ
Check that you have set the correct manufacturer’s code.
ˎ
Try repeating the setup procedure using another manufacturer’s code (if listed for your device).
If you still cannot operate the RM-VZ220 after trying all the listed codes, try the Search function (see “Searching
for the correct code”).
Notes
ˎ
If the setting is incomplete,
the SET indicator flashes once
and the indicators turn off.
Start again from the
beginning.
ˎ
If no operations are
performed for 10 seconds
while setting, the setting will
be canceled, and must be
restarted.
ˎ
To cancel the process, press
SET any time. The SET
indicator turns off.
SET
POWER
Device
Select
buttons
Number
buttons
The SET indicator
lights up.
Searching for the correct code
You can set the manufacturer’s code using the Search function.
1 Power on the device with its power switch.
2 Aim the RM-VZ220 at the device you want to set.
3 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
4 Enter 9 - 2 - 2 using the number buttons.
The SET indicator flashes three times.
5 Press and hold à to start searching.
When the device turns off, release the button.
If you overshoot the required code, you can search for the next or previous
code using the
ß
or
ù
button.
6 Press
.
The SET indicator flashes three times and turns off.
7 Check if the code number works correctly (see “Remote Button
Descriptions”).
If you still cannot operate the device, repeat steps to search for another
code that works for most functions of your device.
Checking the manufacturer’s code you have set
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2 Enter 9 - 3 - 3 using the number buttons.
The SET indicator flashes three times.
3 Press à.
4 When the SET indicator starts flashing, count the number of flashes.
Short flash(es) indicate which digit (first, second, etc.), followed by long
flash(es) to indicate the digit number (i.e., 2 long flashes represent the
number 2). “0” is indicated by rapid flashing.
Determine the 5-digit code number this way. To recheck, press à.
5 Press SET to finish.
Clearing the automatic power-on control (Sony
devices only)
The Device Select buttons are preset to automatically turn on a device when
pressed.
To cancel the function:
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
, then release both buttons.
2 Enter 9 - 7 - 7 using the number buttons.
The SET indicator flashes three times.
3 Press the desired Device Select button.
The SET indicator flashes three times and turns off.
To set the function again, perform the same procedure above.
Restoring the factory settings
You can clear all the settings and reset the RM-VZ220 to its factory settings.
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
, then release both buttons.
2 Enter 9 - 0 - 0 using the number buttons.
The SET indicator flashes three times.
To cancel, press any button except
.
3 Press
.
The SET indicator flashes three times and turns off.
Remote Button Descriptions
General
ȩȪ
SET: Press to set up the RM-VZ220. The indicator lights or flashes while
setting.
ȫ
Device Select buttons: Press to select the device to operate.
Ȯ
GUIDE: Displays the program guide (EPG).
ȯ
j//V/p/
: Moves the cursor to select a menu item/enters the selected item.
ȱ
RETURN: Returns to the previous display/exits the menu.
ȳ
VOL +/–: Turns the volume up/down.
ȸ
POWER: Turns the selected device on and off.
Ⱦ
MUTING: Mutes the volume. Press again to turn muting off.
ɀ
SLEEP: Enables the Sleep function (when available).
The number 5, CH+, and à buttons each have a tactile dot for ease of use.
The GUIDE and RETURN buttons do not work for a VCR.
Note on the VOL+/– and MUTING buttons
When a TV or other video device is selected, the TV’s volume is controlled. When a
DVD Home Theater is selected, its volume can be controlled.
TV
Ȭ
Ã
: VIDEO 1 input
: VIDEO 2 input
: HDMI input
Ñ
: RGB input
ù
: (PIP INPUT) Changes the
input mode of the “window”
picture.
à
: (PIP) Turns the “window”
picture on and off.
ß
: (PIP MOVE) Moves the
location of the “window” picture.
ê
: (PIP STILL) Freezes the
“window” picture.
Ą
: (PIP SWAP) Switches between
“main” and “window” picture.
ȭ
A: Red button
B: Green button
C: Yellow button
D: Blue button
Ȱ
LIST: (CAPTION) Displays closed
captioning.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵȶɁ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: (PIP CH +/–) Changes
the channel up/down in the
“window” picture.
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: Selects the channel
previously selected.
ȿ
CH +/–: Switches the channel up/
down.
Cable set top box/IPTV
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A, B, C buttons
D: (Live TV) Displays Master
Guide.
Ȱ
LIST: Displays the title of recorded
program.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵ ȶ Ɂ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: Page up/down
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: Switches between the
current and previous channel.
ȿ
CH +/–: Switches the channel up/
down.
Satellite receiver
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: Red button
B: Green button
C: Yellow button
D: Blue button
Ȱ
LIST: Displays the title of recorded
program/PVR menu.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: (TV/SAT) Switches the
output between SAT and TV.
ȵ ȶ Ɂ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: Page up/down
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the Satellite
dish menu/Station Index.
Ƚ
RECALL: Tunes to the last tuned
station.
ȿ
CH +/–: Switches the channel up/
down.
VCR
Ȭ
ù
: Rewinds.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȷ
ì: Ejects a tape.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: (ANT/SW) Switches
the antenna output.
Ƚ
RECALL: (DRIVE SELECT) Selects
the deck.
ȿ
CH +/–: Switches the channel up/
down.
Ɂ
ENTER: Enters the selected item.
DVD player/recorder
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records (for DVD recorder).
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȱ
LIST: Displays the Title List.
Ȳ
MENU: Displays the DVD menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +: (DVD) Selects the DVD
drive.
PAGE –: (HDD) Selects the
internal HDD (hard disk drive).
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: (DRIVE SELECT)
Switches between HDD and DVD.
ȿ
CH +/–: Switches the channel up/
down (for DVD recorder).
Ɂ
ENTER: Enters the selected item.
Blu-ray Disc/HD-DVD player
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records (for BD recorder).
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȳ
MENU: Displays the Pop-up Menu/
Disc Menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +: (BD) Selects the BD drive.
PAGE –: (HDD) Selects the
internal HDD (hard disk drive).
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the options
menu.
Ɂ
ENTER: Enters the selected item.
DVR (digital video recorder)/PVR (personal video recorder)
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: (REPLAY*) Enables the Replay
function for DVR/Replay TV.
B: (Live TV*) Displays Master
Guide.
Ȱ
LIST: Displays the title of recorded
program.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +/–: Page up/down,
Thumbs* up/down
Ȼ
INFO: (DISPLAY) Displays the
playback information.
Ƚ
RECALL: Selects the channel
previously selected.
ȿ
CH +/–: Switches the channel up/
down.
Ɂ
ENTER: Enters the selected item.
* These buttons correspond to TiVo
service or the Replay service. Refer to
its instruction manual for details.
DVD Home Theater
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȱ
LIST: Enables the SOUND FIELD
function.
Ȳ
MENU: Displays the DVD menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the amplifier
menu.
Ƚ
RECALL: (BAND) Selects FM/AM.
ȿ
CH +/–: Presets or tunes frequency
up/down.
Ɂ
ENTER: Enters the selected item.
Notes on using the RM-VZ220
ˎ
The RM-VZ220 will not perform functions that the device is not designed for. For
example, if your TV does not have the muting function, MUTING on the RM-VZ220
will not function with your TV.
ˎ
The function of the buttons varies depending on settings/operating modes. The table
of “Remote Button Descriptions” shows how the RM-VZ220 generally operates for
each device in the preset mode.
ˎ
If your cable set top box can control volume, be sure to set its volume to a moderate
level. If the volume on the cable set top box is turned down completely, you will not be
able to adjust your TV’s volume with the RM-VZ220.
Manufacturer’s Code List /
Lista de códigos del fabricante
English
The following tables show brand names (Brand) and their corresponding
code numbers (Code No.).
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2 Enter the manufacturer’s code.
The SET indicator flashes three times and turns off.
Español
La siguiente tabla muestra los nombres de las marcas (Brand) y el número
de código correspondiente (Code No.).
1 Presione y mantenga presionado el botón SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras tiene presionado el botón SET, presione el botón de selección de
dispositivo deseado y luego suelte ambos botones.
2 Ingrese el código del fabricante.
El indicador SET parpadeará tres veces y se apagará.
Brand Code No.
Acer 01339
Action 00650
Admiral 00463
Akai 00812, 01675, 00702, 02232
Akira 01733
AOC 01365, 01589
Apex Digital 00748
Aventura 00171
Bell & Howell 00154
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Dynex 01463, 01810, 02049
Electroband 00000
Electrograph 01755
Electrohome 00463
Elektra 01661
Element 01687
Emerson 01864, 00154, 00463, 00171,
01661, 01394
Emprex 01765
Envision 01365, 01589
ESA 00812, 00171
Fisher 00154
Funai 00171
Gateway 01755, 01756
GE 01447, 00051, 02359
GFM 00171
Haier 01748, 01749, 02309, 02449
Harman/Kardon 00054
Hisense 00748, 01314, 02098
Hitachi 01643, 02215, 02433
iLo 01684
Infinity 00054
Insignia 01564, 00171, 02049
JBL 00054
JCB 00000
JVC 00731, 01253, 01601, 01774
KDS 01687
Kolin 01331
LG 01423, 02358
LXI 00054, 00154, 00156
MAG 01687
Magnavox 01454, 01866, 00054, 01254,
01365, 02372
Marantz 00054
Matsushita 00650
Maxent 01755
Memorex 00154, 00463, 00150
MGA 00150
Midland 00051
Brand Code No.
Mitsubishi 01250, 00150, 00836
NAD 00156
NEC 01797
NetTV 01755
Norcent 00748, 01365, 01589
Olevia 01610, 01144, 01331
Onida 01253, 02396
Optimus 00154, 00650
Orion 00463, 01463
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
Quasar 00051, 00650
RadioShack 00154
RCA 01447, 01781, 02187, 02247,
02403, 02429, 02434
Realistic 00154
Sampo 01755
Samsung 00812, 00702
Sansui 00463
Sanyo 00154, 01142
Sceptre 01360, 01599
Scott 01711
Sears 00054, 00154, 00156, 00171
Sharp 00818
Sony 00810, 00000
Spectroniq 01687
Squareview 00171
Superscan 00864
Supreme 00000
SVA 00748
Sylvania 01864, 00054, 00171, 01314,
01394
Symphonic 00171
Syntax 01610, 01144, 01331
Tatung 01756
TCL 02403, 02429
Technics 00051
Techwood 00051
Teknika 00054, 00150
Telefunken 00702
Toshiba 01524, 00154, 00156, 00650
TVS 00463
Venturer 01865
Videocon 01540, 01541, 02436
Vidikron 00054
Viewsonic 01755, 00864, 00885, 01627,
01742
Viore 01684, 02104, 02352
Vizio 01758, 00864, 00885, 01756
VU 02098
TV / TV
Brand Code No.
Wards 00054
Waycon 00156
Westinghouse 01712, 00885, 01577
White
Westinghouse
00463, 01661
Wyse 01365
Zenith 00463, 01661
Brand Code No.
Accurian 10675
Akai 10695
Allegro 10869
Apex Digital 10672, 11056
Bel Canto Design 11571
Broksonic 10695
CineVision 10869
Citizen 10695
CyberHome 11024
Daewoo 10869
Denon 10490, 11634, 12258
Disney 10675, 11270
Emerson 10591, 10675
Enterprise 10591
Funai 10675
GE 10522
GFM 10675
Go Video 10744, 10741, 10869, 11044,
11075
GoldStar 10741
Harman/Kardon 11229
Hitachi 10573, 10664
Hiteker 10672
Insignia 10675, 12428, 12596
Integra 11769, 10627, 12147
JVC 10623, 10867, 11164
Kenwood 10490
LG 10591, 10741, 10869
Magnavox 10503, 10539, 10646, 10675,
11354
Marantz 10539, 12414, 12432
Memorex 10695, 11270, 12213
Microsoft 10522, 12083
Mitsubishi 11521
NAD 10741, 12572
Olevia 12331
Onkyo 10503, 11769, 10627, 11627,
12147
Brand Code No.
Oppo 10575, 12545
Panasonic 10490, 11579, 11641
Philco 10675
Philips 10503, 10539, 12056, 12084,
10646, 10675, 11267, 11354,
12434
Pioneer 10142, 10631, 11571, 12442
Polk Audio 10539
Presidian 10675
Proscan 10522
RCA 10522, 11769, 10822, 12213,
12587, 12592, 12594
Rio 10869
Rotel 10623
Samsung 10490, 10573, 10199, 11044,
11075, 12329, 12489
Sansui 10695
Sanyo 10695
Sharp 10630, 10675, 12250
Shinsonic 10533
Sonic Blue 10869
Sony 11633, 10533, 10864, 11033,
11070, 11431, 11516
Sylvania 10675
Symphonic 10675
TCL 12587
Technics 10490
Tivo 11503
Toshiba 10503, 11769, 10695, 11154,
11503, 12006, 12277
Urban Concepts 10503
Viore 12553
Vizio 12563
Vtrek 12587
Xbox 10522, 12083
Yamaha 10490, 10539, 10497, 10817,
12298
Zenith 10503, 10591, 10741, 10869
DVD player / Reproductor de DVD
Brand Code No.
Accurian 10675
Apex Digital 11056
Funai 10675
Go Video 10741
JVC 11164
LG 10741
Magnavox 10646, 10675
Panasonic 10490, 11579
Philips 10646
Brand Code No.
Pioneer 10631
RCA 10522
Samsung 10490
Sharp 10675
Sony 11033, 11070, 11431
Sylvania 10675
Toshiba 12277
Zenith 10741
DVD recorder / Grabadora de DVD
Blu-ray Disc/HD-DVD player/
Reproductor de Blu-ray Disc/HD-DVD
Brand Code No.
Denon 12258
Insignia 10675, 12428, 12596
Integra 11769, 12147
LG 10741
Magnavox 10675
Marantz 12414, 12432
Microsoft 12083
NAD 12572
Olevia 12331
Onkyo 11769, 12147
Oppo 12545
Panasonic 11641
Brand Code No.
Philips 12084, 12434
Pioneer 10142, 12442
RCA 11769
Samsung 10199
Sharp 12250
Sony 11516
Sylvania 10675
Toshiba 11769
Viore 12553
Vizio 12563
Xbox 12083
Yamaha 12298
RM-VZ220_U [US,ES] 4-170-642-12(1)RM-VZ220_U [US,ES] 4-170-642-12(1)
4-170-642-12(1)
Remote Commander
RM-VZ220
©2010 Sony Corporation Printed in China
Operating Instructions
Manual de instrucciones (parte posterior)
English
For the Customers in the U.S.A.
WARNING
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
ˎ
Reorient or relocate the receiving antenna.
ˎ
Increase the separation between the equipment and receiver.
ˎ
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
ˎ
Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this
manual could void your authority to operate this equipment.
Setting Up the RM-VZ220
The RM-VZ220 is preset at the factory to operate Sony brand video devices
set to any of the Device Select buttons (see the table below).
To use with non-Sony devices, or Sony devices that are not preset at the
factory, set the manufacturer’s code for each device.
Devices Button Factory setting*
TV
TV
Sony TV (00810)
TV, Cable set top box, Satellite
receiver, IPTV, DVD player, DVD
recorder, Blu-ray Disc player, DVR
(digital video recorder), PVR
(personal video recorder), VCR,
DVD Home Theater
CBL (SAT)
Cable set top box (non-
Sony) (51376)
VCR
Sony VCR (60032)
DVD
Sony DVD player
(11033)
* The five-digit code is the preset manufacturer’s code.
Note
Only a TV can be assigned to the TV Device Select button. You can assign any device to
the other Device Select buttons.
Installing the batteries
Slide open the battery compartment and insert two size AA (R6) dry
batteries (not supplied).
Insert the batteries (negative end first) through the guide clamp within each
compartment as shown below.
1 2
Battery life
Under normal conditions, size AA (LR6) alkaline batteries will last up to one
year. If the RM-VZ220 does not operate properly, the batteries might be
drained. Replace both batteries with new ones.
Notes
ˎ
Replace the batteries within 2 minutes after removing them, and do not press any
button when replacing the batteries. Otherwise, your code settings may be cleared.
ˎ
Do not use an old battery with a new one, or mix different types of batteries together.
ˎ
If the electrolyte inside the battery should leak, wipe the contaminated area of the
battery compartment with a cloth and replace the old batteries with new ones. To
prevent electrolyte from leaking, remove the batteries when you plan not to use the
RM-VZ220 for a long period of time.
Specifications
Operating distance Approx. 11 m (36 ft) (varies depending on devices of
different manufacturers)
Power requirements Two size AA (R6) dry batteries (not supplied)
Battery life Approx. 1 year when using size AA (LR6) alkaline batteries
(varies depending on frequency of button use - up to approx.
300 times per day.)
Dimensions Approx. 53 × 213 × 27 mm (2
1
/
8
× 8
1
/
2
× 1
1
/
8
in.)
(w/h/d)
Mass Approx. 100 g (3.5 oz) (not including batteries)
Design and specifications are subject to change without notice.
Troubleshooting
If you have problems setting up or using the RM-VZ220:
ˎ
Carefully perform the setup procedure of “Startup Guide.” If the RM-VZ220 does not
work, try repeating the setup procedure using another manufacturer’s code (if listed
for your device). If you still cannot operate the RM-VZ220, try the Search function
(see “Searching for the correct code”).
ˎ
Aim the RM-VZ220 directly at the device.
ˎ
Remove any obstacles in the path between the RM-VZ220 and the device.
ˎ
Make sure you have pressed the correct Device Select button.
ˎ
Check that the device has infrared remote capability. For example, if your device did
not come with a remote control, it probably is not capable of being controlled by the
RM-VZ220.
ˎ
The batteries are weak, or not inserted correctly. Replace them with new ones or insert
them correctly.
For the customers in the U.S.A.
Customer Support Information
After you have read through this manual, if you still cannot get the RM-VZ220 to work
properly, call the Sony Customer Support Helpline at
1-800-822-2217.
Startup Guide
This guide shows you how to set up and use the RM-VZ220 to operate your devices.
If your Sony device has already been preset, see “Operate the device.”
Set the manufacturer’s code
Example: To set up a Philips TV
1
Find the manufacturer’s code in “Manufacturer’s Code List.”
Manufacturer’s Code List /
Lista de códigos del fabricante
English
The following tables show brand names (Brand) and their corresponding
code numbers (Code No.).
1 Press and hold SET for more than 3 seconds.
TheSET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2 Enter the manufacturer’s code.
TheSET indicator flashes three times and turns off.
Español
La siguiente tabla muestra los nombres de las marcas (Brand) y el número
de código correspondiente (Code No.).
1 Presione y mantenga presionado el botón SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras tiene presionado el botón SET, presione el botón de selección de
dispositivo deseado y luego suelte ambos botones.
2 Ingrese el código del fabricante.
El indicador SET parpadeará tres veces y se apagará.
Brand Code No.
Sony 00810, 00000
Acer 01339
Action 00650
Admiral 00463
Akai 00812, 01675, 00702, 02232
Akira 01733
AOC 01365, 01589
Apex Digital 00748
Aventura 00171
Bell & Howell 00154
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Dynex 01463, 01810, 02049
Electroband 00000
Electrograph 01755
Electrohome 00463
Elektra 01661
Element 01687
Emerson 01864, 00154, 00463, 00171,
01661, 01394
Emprex 01765
Envision 01365, 01589
ESA 00812, 00171
Fisher 00154
Funai 00171
Gateway 01755, 01756
GE 01447, 00051, 02359
GFM 00171
Haier 01748, 01749, 02309, 02449
Harman/Kardon 00054
Hisense 00748, 01314, 02098
Hitachi 01643, 02215, 02433
iLo 01684
Infinity 00054
Insignia 01564, 00171, 02049
JBL 00054
JCB 00000
JVC 00731, 01253, 01601, 01774
KDS 01687
Kolin 01331
LG 01423, 02358
LXI 00054, 00154, 00156
MAG 01687
Magnavox 01454, 01866, 00054, 01254,
01365, 02372
Marantz 00054
Matsushita 00650
Maxent 01755
Memorex 00154, 00463, 00150
MGA 00150
Brand Code No.
Midland 00051
Mitsubishi 01250, 00150, 00836
NAD 00156
NEC 01797
NetTV 01755
Norcent 00748, 01365, 01589
Olevia 01610, 01144, 01331
Onida 01253, 02396
Optimus 00154, 00650
Orion 00463, 01463
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
Quasar 00051, 00650
RadioShack 00154
RCA 01447, 01781, 02187, 02247,
02403, 02429, 02434
Realistic 00154
Sampo 01755
Samsung 00812, 00702
Sansui 00463
Sanyo 00154, 01142
Sceptre 01360, 01599
Scott 01711
Sears 00054, 00154, 00156, 00171
Sharp 00818
Spectroniq 01687
Squareview 00171
Superscan 00864
Supreme 00000
SVA 00748
Sylvania 01864, 00054, 00171, 01314,
01394
Symphonic 00171
Syntax 01610, 01144, 01331
Tatung 01756
TCL 02403, 02429
Technics 00051
Techwood 00051
Teknika 00054, 00150
Telefunken 00702
Toshiba 01524, 00154, 00156, 00650
TVS 00463
Venturer 01865
Videocon 01540, 01541, 02436
Vidikron 00054
Viewsonic 01755, 00864, 00885, 01627,
01742
Viore 01684, 02104, 02352
Vizio 01758, 00864, 00885, 01756
VU 02098
TV / TV
Brand Code No.
Wards 00054
Waycon 00156
Westinghouse 01712, 00885, 01577
White
Westinghouse
00463, 01661
Wyse 01365
Zenith 00463, 01661
Brand Code No.
Sony 11633, 10533, 10864, 11033,
11070, 11431, 11516
Accurian 10675
Akai 10695
Allegro 10869
Apex Digital 10672, 11056
Bel Canto Design 11571
Broksonic 10695
CineVision 10869
Citizen 10695
CyberHome 11024
Daewoo 10869
Denon 10490, 11634, 12258
Disney 10675, 11270
Emerson 10591, 10675
Enterprise 10591
Funai 10675
GE 10522
GFM 10675
Go Video 10744, 10741, 10869, 11044,
11075
GoldStar 10741
Harman/Kardon 11229
Hitachi 10573, 10664
Hiteker 10672
Insignia 10675, 12428, 12596
Integra 11769, 10627, 12147
JVC 10623, 10867, 11164
Kenwood 10490
LG 10591, 10741, 10869
Magnavox 10503, 10539, 10646, 10675,
11354
Marantz 10539, 12414, 12432
Memorex 10695, 11270, 12213
Microsoft 10522, 12083
Mitsubishi 11521
NAD 10741, 12572
Olevia 12331
Brand Code No.
Onkyo 10503, 11769, 10627, 11627,
12147
Oppo 10575, 12545
Panasonic 10490, 11579, 11641
Philco 10675
Philips 10503, 10539, 12056, 12084,
10646, 10675, 11267, 11354,
12434
Pioneer 10142, 10631, 11571, 12442
Polk Audio 10539
Presidian 10675
Proscan 10522
RCA 10522, 11769, 10822, 12213,
12587, 12592, 12594
Rio 10869
Rotel 10623
Samsung 10490, 10573, 10199, 11044,
11075, 12329, 12489
Sansui 10695
Sanyo 10695
Sharp 10630, 10675, 12250
Shinsonic 10533
Sonic Blue 10869
Sylvania 10675
Symphonic 10675
TCL 12587
Technics 10490
Tivo 11503
Toshiba 10503, 11769, 10695, 11154,
11503, 12006, 12277
Urban Concepts 10503
Viore 12553
Vizio 12563
Vtrek 12587
Xbox 10522, 12083
Yamaha 10490, 10539, 10497, 10817,
12298
Zenith 10503, 10591, 10741, 10869
DVD player / Reproductor de DVD
Brand Code No.
Sony 11033, 11070, 11431
Accurian 10675
Apex Digital 11056
Funai 10675
Go Video 10741
JVC 11164
LG 10741
Magnavox 10646, 10675
Panasonic 10490, 11579
Brand Code No.
Philips 10646
Pioneer 106 31
RCA 10522
Samsung 10490
Sharp 10675
Sylvania 10675
Toshiba 12277
Zenith 10741
DVD recorder / Grabadora de DVD
Blu-ray Disc/HD-DVD player/
Reproductor de Blu-ray Disc/HD-DVD
Brand Code No.
Sony 11516
Denon 12258
Insignia 10675, 12428, 12596
Integra 11769, 12147
LG 10741
Magnavox 10675
Marantz 12414, 12432
Microsoft 12083
NAD 12572
Olevia 12331
Onkyo 11769, 12147
Oppo 12545
Brand Code No.
Panasonic 11641
Philips 12084, 12434
Pioneer 10142, 12442
RCA 11769
Samsung 10199
Sharp 12250
Sylvania 10675
Toshiba 11769
Viore 12553
Vizio 12563
Xbox 12083
Yamaha 12298
Brand Code No.
Sony 00810, 00000
Acer 01339
Action 00650
Brand Code No.
Midland 00051
Mitsubishi 01250, 00150, 00836
NAD 00156
TV / TV
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
If your device is not listed, try the Search function (see “Searching for the correct code”).
2
Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
the desired Device Select button,
then release both buttons.
3
Enter the manufacturer’s code (01454).
The SET indicator flashes three times and
turns off.
Operate the device
1
Aim the RM-VZ220 directly at the device.
2
Press the Device Select button for the
device you want to operate.
3
Press POWER to turn on the device.
4
Press buttons on the RM-VZ220 to check that they function.
See “Remote Button Descriptions” for the functions of buttons for each device.
If the RM-VZ220 does not seem to be working…
ˎ
Check that you have set the correct manufacturer’s code.
ˎ
Try repeating the setup procedure using another manufacturer’s code (if listed for your device).
If you still cannot operate the RM-VZ220 after trying all the listed codes, try the Search function (see “Searching
for the correct code”).
Notes
ˎ
If the setting is incomplete,
the SET indicator flashes once
and the indicators turn off.
Start again from the
beginning.
ˎ
If no operations are
performed for 10 seconds
while setting, the setting will
be canceled, and must be
restarted.
ˎ
To cancel the process, press
SET any time. The SET
indicator turns off.
SET
POWER
Device
Select
buttons
Number
buttons
The SET indicator
lights up.
Searching for the correct code
You can set the manufacturer’s code using the Search function.
1 Power on the device with its power switch.
2 Aim the RM-VZ220 at the device you want to set.
3 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
4 Enter 9 - 2 - 2 using the number buttons.
The SET indicator flashes three times.
5 Press and hold à to start searching.
When the device turns off, release the button.
If you overshoot the required code, you can search for the next or previous
code using the
ß
or
ù
button.
6 Press
.
The SET indicator flashes three times and turns off.
7 Check if the code number works correctly (see “Remote Button
Descriptions”).
If you still cannot operate the device, repeat steps to search for another
code that works for most functions of your device.
Checking the manufacturer’s code you have set
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2 Enter 9 - 3 - 3 using the number buttons.
The SET indicator flashes three times.
3 Press à.
4 When the SET indicator starts flashing, count the number of flashes.
Short flash(es) indicate which digit (first, second, etc.), followed by long
flash(es) to indicate the digit number (i.e., 2 long flashes represent the
number 2). “0” is indicated by rapid flashing.
Determine the 5-digit code number this way. To recheck, press à.
5 Press SET to finish.
Clearing the automatic power-on control (Sony
devices only)
The Device Select buttons are preset to automatically turn on a device when
pressed.
To cancel the function:
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
, then release both buttons.
2 Enter 9 - 7 - 7 using the number buttons.
The SET indicator flashes three times.
3 Press the desired Device Select button.
The SET indicator flashes three times and turns off.
To set the function again, perform the same procedure above.
Restoring the factory settings
You can clear all the settings and reset the RM-VZ220 to its factory settings.
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press
, then release both buttons.
2 Enter 9 - 0 - 0 using the number buttons.
The SET indicator flashes three times.
To cancel, press any button except
.
3 Press
.
The SET indicator flashes three times and turns off.
Remote Button Descriptions
General
ȩȪ
SET: Press to set up the RM-VZ220. The indicator lights or flashes while
setting.
ȫ
Device Select buttons: Press to select the device to operate.
Ȯ
GUIDE: Displays the program guide (EPG).
ȯ
j//V/p/
: Moves the cursor to select a menu item/enters the selected item.
ȱ
RETURN: Returns to the previous display/exits the menu.
ȳ
VOL +/–: Turns the volume up/down.
ȸ
POWER: Turns the selected device on and off.
Ⱦ
MUTING: Mutes the volume. Press again to turn muting off.
ɀ
SLEEP: Enables the Sleep function (when available).
The number 5, CH+, and à buttons each have a tactile dot for ease of use.
The GUIDE and RETURN buttons do not work for a VCR.
Note on the VOL+/– and MUTING buttons
When a TV or other video device is selected, the TV’s volume is controlled. When a
DVD Home Theater is selected, its volume can be controlled.
TV
Ȭ
Ã
: VIDEO 1 input
: VIDEO 2 input
: HDMI input
Ñ
: RGB input
ù
: (PIP INPUT) Changes the
input mode of the “window”
picture.
à
: (PIP) Turns the “window”
picture on and off.
ß
: (PIP MOVE) Moves the
location of the “window” picture.
ê
: (PIP STILL) Freezes the
“window” picture.
Ą
: (PIP SWAP) Switches between
“main” and “window” picture.
ȭ
A: Red button
B: Green button
C: Yellow button
D: Blue button
Ȱ
LIST: (CAPTION) Displays closed
captioning.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵȶɁ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: (PIP CH +/–) Changes
the channel up/down in the
“window” picture.
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: Selects the channel
previously selected.
ȿ
CH +/–: Switches the channel up/
down.
Cable set top box/IPTV
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A, B, C buttons
D: (Live TV) Displays Master
Guide.
Ȱ
LIST: Displays the title of recorded
program.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵ ȶ Ɂ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: Page up/down
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: Switches between the
current and previous channel.
ȿ
CH +/–: Switches the channel up/
down.
Satellite receiver
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: Red button
B: Green button
C: Yellow button
D: Blue button
Ȱ
LIST: Displays the title of recorded
program/PVR menu.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: (TV/SAT) Switches the
output between SAT and TV.
ȵ ȶ Ɂ
1 – 9, 0, ENTER,
ˎ
(dot):
Changes the channel. For example,
to change to channel 5, press 0 and
5 (or, press 5 and ENTER).
ȹ
PAGE +/–: Page up/down
Ⱥ
FAVORITES: Enables the Favorite
function.
Ȼ
INFO: Displays program
information.
ȼ
OPTIONS: Displays the Satellite
dish menu/Station Index.
Ƚ
RECALL: Tunes to the last tuned
station.
ȿ
CH +/–: Switches the channel up/
down.
VCR
Ȭ
ù
: Rewinds.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȷ
ì: Ejects a tape.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: (ANT/SW) Switches
the antenna output.
Ƚ
RECALL: (DRIVE SELECT) Selects
the deck.
ȿ
CH +/–: Switches the channel up/
down.
Ɂ
ENTER: Enters the selected item.
DVD player/recorder
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records (for DVD recorder).
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȱ
LIST: Displays the Title List.
Ȳ
MENU: Displays the DVD menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +: (DVD) Selects the DVD
drive.
PAGE –: (HDD) Selects the
internal HDD (hard disk drive).
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the options
menu.
Ƚ
RECALL: (DRIVE SELECT)
Switches between HDD and DVD.
ȿ
CH +/–: Switches the channel up/
down (for DVD recorder).
Ɂ
ENTER: Enters the selected item.
Blu-ray Disc/HD-DVD player
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records (for BD recorder).
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȳ
MENU: Displays the Pop-up Menu/
Disc Menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +: (BD) Selects the BD drive.
PAGE –: (HDD) Selects the
internal HDD (hard disk drive).
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the options
menu.
Ɂ
ENTER: Enters the selected item.
DVR (digital video recorder)/PVR (personal video recorder)
Ȭ
Ã
: Proceeds to the previous
location.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Proceeds to the next location.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: (REPLAY*) Enables the Replay
function for DVR/Replay TV.
B: (Live TV*) Displays Master
Guide.
Ȱ
LIST: Displays the title of recorded
program.
Ȳ
MENU: Calls up the menu display.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
ȹ
PAGE +/–: Page up/down,
Thumbs* up/down
Ȼ
INFO: (DISPLAY) Displays the
playback information.
Ƚ
RECALL: Selects the channel
previously selected.
ȿ
CH +/–: Switches the channel up/
down.
Ɂ
ENTER: Enters the selected item.
* These buttons correspond to TiVo
service or the Replay service. Refer to
its instruction manual for details.
DVD Home Theater
Ȭ
Ã
: Skips to the previous
chapter/track.
: Briefly replays the scene
(Flash –).
: Briefly fast forwards the
scene (Flash +).
Ñ
: Skips to the next chapter/
track.
ù
: Fast reverses.
à
: Plays.
ß
: Fast forwards.
Ć: Records.
ê
: Pauses.
Ą
: Stops.
ȭ
A: (SET UP) Calls up the system/
setup menu.
B: (SUBTITLE) Switches the
subtitle.
C: (AUDIO) Changes the sound.
D: (CLEAR) Clears the setting.
Ȱ
LIST: Enables the SOUND FIELD
function.
Ȳ
MENU: Displays the DVD menu.
ȴ
INPUT: Changes the input mode.
ȵ
1 – 9, 0: Number buttons
ȶ
ˎ
(dot): (+10) Selects numbers 10
and above.
ȷ
ì: Opens/closes the disc tray.
Ⱥ
FAVORITES: (TOP MENU)
Displays the Top Menu.
Ȼ
INFO: (DISPLAY) Displays the
playback information.
ȼ
OPTIONS: Displays the amplifier
menu.
Ƚ
RECALL: (BAND) Selects FM/AM.
ȿ
CH +/–: Presets or tunes frequency
up/down.
Ɂ
ENTER: Enters the selected item.
Notes on using the RM-VZ220
ˎ
The RM-VZ220 will not perform functions that the device is not designed for. For
example, if your TV does not have the muting function, MUTING on the RM-VZ220
will not function with your TV.
ˎ
The function of the buttons varies depending on settings/operating modes. The table
of “Remote Button Descriptions” shows how the RM-VZ220 generally operates for
each device in the preset mode.
ˎ
If your cable set top box can control volume, be sure to set its volume to a moderate
level. If the volume on the cable set top box is turned down completely, you will not be
able to adjust your TV’s volume with the RM-VZ220.
Manufacturer’s Code List /
Lista de códigos del fabricante
English
The following tables show brand names (Brand) and their corresponding
code numbers (Code No.).
1 Press and hold SET for more than 3 seconds.
The SET indicator lights up.
While keeping SET held down, press the desired Device Select button,
then release both buttons.
2 Enter the manufacturer’s code.
The SET indicator flashes three times and turns off.
Español
La siguiente tabla muestra los nombres de las marcas (Brand) y el número
de código correspondiente (Code No.).
1 Presione y mantenga presionado el botón SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras tiene presionado el botón SET, presione el botón de selección de
dispositivo deseado y luego suelte ambos botones.
2 Ingrese el código del fabricante.
El indicador SET parpadeará tres veces y se apagará.
Brand Code No.
Acer 01339
Action 00650
Admiral 00463
Akai 00812, 01675, 00702, 02232
Akira 01733
AOC 01365, 01589
Apex Digital 00748
Aventura 00171
Bell & Howell 00154
BPL 01543
Broksonic 00463
Carver 00054
Celebrity 00000
Coby 02306, 02345, 02348
Commercial
Solutions
01447
Crosley 00054
Curtis 02352
Curtis Mathes 00054, 00154, 00702, 01661
Daewoo 01661
Digital Lifestyles 01765
Durabrand 00463, 00171
Dynex 01463, 01810, 02049
Electroband 00000
Electrograph 01755
Electrohome 00463
Elektra 01661
Element 01687
Emerson 01864, 00154, 00463, 00171,
01661, 01394
Emprex 01765
Envision 01365, 01589
ESA 00812, 00171
Fisher 00154
Funai 00171
Gateway 01755, 01756
GE 01447, 00051, 02359
GFM 00171
Haier 01748, 01749, 02309, 02449
Harman/Kardon 00054
Hisense 00748, 01314, 02098
Hitachi 01643, 02215, 02433
iLo 01684
Infinity 00054
Insignia 01564, 00171, 02049
JBL 00054
JCB 00000
JVC 00731, 01253, 01601, 01774
KDS 01687
Kolin 01331
LG 01423, 02358
LXI 00054, 00154, 00156
MAG 01687
Magnavox 01454, 01866, 00054, 01254,
01365, 02372
Marantz 00054
Matsushita 00650
Maxent 01755
Memorex 00154, 00463, 00150
MGA 00150
Midland 00051
Brand Code No.
Mitsubishi 01250, 00150, 00836
NAD 00156
NEC 01797
NetTV 01755
Norcent 00748, 01365, 01589
Olevia 01610, 01144, 01331
Onida 01253, 02396
Optimus 00154, 00650
Orion 00463, 01463
Panasonic 01480, 00051, 00650
PARK 02104
Penney 00156, 00051
Petters 01523
Philco 00054
Philips 01454, 00054, 00690, 01744,
02372
Pioneer 01457, 01260
Polaroid 01523, 01276, 01314, 01687
Portland 01661
Prism 00051
Proscan 01447, 02147, 02256
Proview 01687
Quasar 00051, 00650
RadioShack 00154
RCA 01447, 01781, 02187, 02247,
02403, 02429, 02434
Realistic 00154
Sampo 01755
Samsung 00812, 00702
Sansui 00463
Sanyo 00154, 01142
Sceptre 01360, 01599
Scott 01711
Sears 00054, 00154, 00156, 00171
Sharp 00818
Sony 00810, 00000
Spectroniq 01687
Squareview 00171
Superscan 00864
Supreme 00000
SVA 00748
Sylvania 01864, 00054, 00171, 01314,
01394
Symphonic 00171
Syntax 01610, 01144, 01331
Tatung 01756
TCL 02403, 02429
Technics 00051
Techwood 00051
Teknika 00054, 00150
Telefunken 00702
Toshiba 01524, 00154, 00156, 00650
TVS 00463
Venturer 01865
Videocon 01540, 01541, 02436
Vidikron 00054
Viewsonic 01755, 00864, 00885, 01627,
01742
Viore 01684, 02104, 02352
Vizio 01758, 00864, 00885, 01756
VU 02098
TV / TV
Brand Code No.
Wards 00054
Waycon 00156
Westinghouse 01712, 00885, 01577
White
Westinghouse
00463, 01661
Wyse 01365
Zenith 00463, 01661
Brand Code No.
Accurian 10675
Akai 10695
Allegro 10869
Apex Digital 10672, 11056
Bel Canto Design 11571
Broksonic 10695
CineVision 10869
Citizen 10695
CyberHome 11024
Daewoo 10869
Denon 10490, 11634, 12258
Disney 10675, 11270
Emerson 10591, 10675
Enterprise 10591
Funai 10675
GE 10522
GFM 10675
Go Video 10744, 10741, 10869, 11044,
11075
GoldStar 10741
Harman/Kardon 11229
Hitachi 10573, 10664
Hiteker 10672
Insignia 10675, 12428, 12596
Integra 11769, 10627, 12147
JVC 10623, 10867, 11164
Kenwood 10490
LG 10591, 10741, 10869
Magnavox 10503, 10539, 10646, 10675,
11354
Marantz 10539, 12414, 12432
Memorex 10695, 11270, 12213
Microsoft 10522, 12083
Mitsubishi 11521
NAD 10741, 12572
Olevia 12331
Onkyo 10503, 11769, 10627, 11627,
12147
Brand Code No.
Oppo 10575, 12545
Panasonic 10490, 11579, 11641
Philco 10675
Philips 10503, 10539, 12056, 12084,
10646, 10675, 11267, 11354,
12434
Pioneer 10142, 10631, 11571, 12442
Polk Audio 10539
Presidian 10675
Proscan 10522
RCA 10522, 11769, 10822, 12213,
12587, 12592, 12594
Rio 10869
Rotel 10623
Samsung 10490, 10573, 10199, 11044,
11075, 12329, 12489
Sansui 10695
Sanyo 10695
Sharp 10630, 10675, 12250
Shinsonic 10533
Sonic Blue 10869
Sony 11633, 10533, 10864, 11033,
11070, 11431, 11516
Sylvania 10675
Symphonic 10675
TCL 12587
Technics 10490
Tivo 11503
Toshiba 10503, 11769, 10695, 11154,
11503, 12006, 12277
Urban Concepts 10503
Viore 12553
Vizio 12563
Vtrek 12587
Xbox 10522, 12083
Yamaha 10490, 10539, 10497, 10817,
12298
Zenith 10503, 10591, 10741, 10869
DVD player / Reproductor de DVD
Brand Code No.
Accurian 10675
Apex Digital 11056
Funai 10675
Go Video 10741
JVC 11164
LG 10741
Magnavox 10646, 10675
Panasonic 10490, 11579
Philips 10646
Brand Code No.
Pioneer 10631
RCA 10522
Samsung 10490
Sharp 10675
Sony 11033, 11070, 11431
Sylvania 10675
Toshiba 12277
Zenith 10741
DVD recorder / Grabadora de DVD
Blu-ray Disc/HD-DVD player/
Reproductor de Blu-ray Disc/HD-DVD
Brand Code No.
Denon 12258
Insignia 10675, 12428, 12596
Integra 11769, 12147
LG 10741
Magnavox 10675
Marantz 12414, 12432
Microsoft 12083
NAD 12572
Olevia 12331
Onkyo 11769, 12147
Oppo 12545
Panasonic 11641
Brand Code No.
Philips 12084, 12434
Pioneer 10142, 12442
RCA 11769
Samsung 10199
Sharp 12250
Sony 11516
Sylvania 10675
Toshiba 11769
Viore 12553
Vizio 12563
Xbox 12083
Yamaha 12298
Si su dispositivo no figura en la lista, intente con la función Búsqueda (consulte “Búsqueda del
código del fabricante”).
2
Presione y mantenga presionado el
botón SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras tiene presionado el botón
SET, presione el botón de selección
de dispositivo deseado y luego suelte
ambos botones.
3
Ingrese el código del fabricante (01454).
El indicador SET parpadeará tres veces y se
apagará.
Funcionamiento del dispositivo
1
Apunte el RM-VZ220 directamente al dispositivo.
2
Presione el botón de selección de dispositivo
del dispositivo que desee hacer funcionar.
3
Presione POWER para encender el dispositivo.
4
Presione los botones en el RM-VZ220 para comprobar que funcionan.
Consulte “Descripción de los botones del control remoto” para conocer las funciones de los botones para cada
dispositivo.
Si el RM-VZ220 parece no estar funcionando…
Compruebe que haya establecido el código del fabricante correcto.
Intente repetir el procedimiento de configuración usando otro código de fabricante (si hay otros en la
enumeración de códigos de su dispositivo).
Si sigue sin poder operar el RM-VZ220 después de probar todos los códigos de la lista, intente con la función
Búsqueda (consulte “Búsqueda del código del fabricante”).
Notas
Si la configuración está
incompleta, el indicador SET
parpadeará una vez y los
indicadores se apagarán.
Vuelva a comenzar desde el
principio.
Si no se realizan operaciones
en el transcurso de 10
segundos cuando se está
realizando la configuración, la
configuración se cancelará y
deberá volver a iniciarse.
Para cancelar el proceso,
presione SET en cualquier
momento. El indicador SET se
apaga.
SET
POWER
Botones de
selección
de
dispositivo
Botones
numéricos
Se encenderá la luz
indicadora SET.
Búsqueda del código del fabricante
Puede configurar el código del fabricante correcto usando la función
Búsqueda.
1
Encienda el dispositivo con su botón de encendido.
2
Apunte el RM-VZ220 al dispositivo que desea configurar.
3
Presione y mantenga presionado el botón SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras tiene presionado el botón SET, presione el botón de selección de
dispositivo deseado y luego suelte ambos botones.
4
Ingrese 9 - 2 - 2 usando los botones con números.
El indicador SET parpadea tres veces.
5
Presione y mantenga presionado para comenzar a buscar.
Cuando el dispositivo se apague suelte el botón.
Si se pasa del código que necesita, puede buscar el código anterior o
siguiente con los botones
o
.
6
Presione .
El indicador SET parpadeará tres veces y se apagará.
7
Compruebe si el número de código funciona correctamente (consulte
“Descripción de los botones del control remoto”).
Si sigue sin poder operar el dispositivo, repita los pasos para buscar otro
código que funcione con la mayoría de las funciones de su dispositivo.
Comprobación del código del fabricante que
configuró
1 Presione y mantenga presionado el botón SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras tiene presionado el botón SET, presione el botón de selección de
dispositivo deseado y luego suelte ambos botones.
2
Ingrese 9 - 3 - 3 usando los botones con números.
El indicador SET parpadea tres veces.
3
Presione .
4
Cuando el indicador SET comience a parpadear, cuente el número de
parpadeos.
Los parpadeos cortos indican el dígito (primero, segundo, etc.), seguidos
de los parpadeos largos que indican el número del dígito (p. ej., 2
parpadeos largos representan el número 2). Los parpadeos rápidos
representan el “0”.
Determine de esta forma el número de código de 5 dígitos. Para chequear
nuevamente, presione .
5
Presione SET para finalizar.
Para anular el control de encendido automático
(solamente de los dispositivos Sony)
Los botones de selección del dispositivo están configurados para encender
un dispositivo en forma automática cuando se presionan.
Para cancelar la función:
1
Presione y mantenga presionado SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras mantiene presionado SET, presione , luego suelte ambos
botones.
2
Ingrese 9 - 7 - 7 usando los botones con números.
El indicador SET parpadea tres veces.
3
Presione el botón de selección de dispositivos que desea.
El indicador SET parpadeará tres veces y se apagará.
Para volver a establecer la función, siga el mismo procedimiento descrito
arriba.
Recuperación de la configuración de fábrica
Puede eliminar todas las configuraciones y restablecer la configuración de
fábrica del RM-VZ220.
1
Presione y mantenga presionado SET durante más de 3 segundos.
Se encenderá la luz indicadora SET.
Mientras mantiene presionado SET, presione , luego suelte ambos
botones.
2
Ingrese 9 - 0 - 0 usando los botones con números.
El indicador SET parpadea tres veces.
Para cancelar presione cualquier botón excepto .
3
Presione .
El indicador SET parpadeará tres veces y se apagará.
Decodificador de cable/IPTV
: Va a la ubicación anterior.
: Muestra otra vez brevemente
la escena (Flash –).
: Avanza brevemente la escena
(Flash +).
: Va a la siguiente ubicación.
: Rebobina rápidamente.
: Reproduce.
: Avanza rápidamente.
: Graba.
: Pausa.
: Detiene.
Botones A, B, C
D: (Live TV) Muestra la guía
maestra.
LIST: Muestra el título del
programa grabado.
MENU: Muestra el menú.
INPUT: Cambia el modo de
entrada.
1 – 9, 0, ENTER,
(punto):
Cambia de canal. Por ejemplo, para
cambiar al canal 5, presione 0 y 5
(o presione 5 y ENTER).
PAGE +/–: Avanza/retrocede la
página.
FAVORITES: Habilita la función
Favorito.
INFO: Muestra información de
programación.
OPTIONS: Muestra el menú de
opciones.
RECALL: Cambia entre el canal
actual y el anterior.
CH +/–: Cambia el canal hacia
arriba/abajo.
Receptor de satélite
: Va a la ubicación anterior.
: Muestra otra vez brevemente
la escena (Flash –).
: Avanza brevemente la escena
(Flash +).
: Va a la siguiente ubicación.
: Rebobina rápidamente.
: Reproduce.
: Avanza rápidamente.
: Graba.
: Pausa.
: Detiene.
A: Botón rojo
B: Botón verde
C: Botón amarillo
D: Botón azul
LIST: Muestra el título del
programa grabado/el menú PVR.
MENU: Muestra el menú.
INPUT: (TV/SAT) Cambia la salida
entre SAT y TV (cuando está
conectado a un televisor).
1 – 9, 0, ENTER,
(punto):
Cambia de canal. Por ejemplo, para
cambiar al canal 5, presione 0 y 5
(o presione 5 y ENTER).
PAGE +/–: Avanza/retrocede la
página
FAVORITES: Habilita la función
Favorito.
INFO: Muestra información de
programación.
OPTIONS: Muestra el menú del
satélite/índice de la estación.
RECALL: Sintoniza la última
estación sintonizada.
CH +/–: Cambia el canal hacia
arriba/abajo.
VCR
: Rebobina.
: Reproduce.
: Avanza rápidamente.
: Graba.
: Pausa.
: Detiene.
INPUT: Cambia el modo de
entrada.
1 – 9, 0: Botones numéricos
: Expulsa la cinta.
INFO: (MOSTRAR) Muestra la
información de reproducción.
OPTIONS: (ANT/SW) Cambia la
salida de la antena.
RECALL: (SELECCIONAR LA
UNIDAD) Selecciona la casetera.
CH +/–: Cambia el canal hacia
arriba/abajo.
ENTER: Accede al elemento
seleccionado.
Reproductor/grabador de DVD
: Va al capítulo/pista anterior.
: Muestra otra vez brevemente
la escena (Flash –).
: Avanza brevemente la escena
(Flash +).
: Va al siguiente capítulo/pista.
: Rebobina rápidamente.
: Reproduce.
: Avanza rápidamente.
: Graba (para la grabadora de
DVD).
: Pausa.
: Detiene.
A: (CONFIGURACIÓN) Muestra
el menú del sistema/
configuración.
B: (SUBTÍTULO) Cambia el
subtítulo.
C: (AUDIO) Cambia el sonido.
D: (BORRAR) Borra la
configuración.
LIST: Muestra la lista de títulos.
MENU: Muestra el menú del DVD.
INPUT: Cambia el modo de
entrada.
1 – 9, 0: Botones numéricos
(punto): (+10) Selecciona los
números a partir del 10.
: Abre/cierra la bandeja del disco.
PAGE +: (DVD) Selecciona la
unidad de DVD.
PAGE –: (HDD) Selecciona el disco
duro interno.
FAVORITES: (MENÚ PRINCIPAL)
Muestra el menú principal.
INFO: (MOSTRAR) Muestra la
información de reproducción.
OPTIONS: Muestra el menú de
opciones.
RECALL: (SELECCIÓN DE LA
UNIDAD) Cambia entre HDD y
DVD.
CH +/–: Cambia el canal hacia
arriba/abajo (para la grabadora de
DVD).
ENTER: Accede al elemento
seleccionado.
Descripción de los botones del control
remoto
General
SET: Presione para configurar el RM-VZ220. El indicador se enciende o
parpadea durante la configuración.
Botones de selección de dispositivo: Presione para seleccionar el
dispositivo para operar.
GUIDE: Muestra la guía de programación (EPG).
//// : Mueve el cursor para seleccionar un elemento del menú. Accede
al elemento seleccionado.
RETURN: Vuelve a la visualización anterior/sale del menú.
VOL +/–: Sube/baja el volumen.
POWER: Enciende y apaga el dispositivo seleccionado.
MUTING: Silencia el volumen. Presione nuevamente para silenciar el volumen.
SLEEP: Habilita la función Sleep (cuando está disponible).
El número 5, CH+ y el botón tienen un punto táctil cada uno para facilitar el uso.
Los botones GUIDE y RETURN no funcionan con un VCR.
Nota sobre los botones VOL+/– y MUTING
Cuando se selecciona un TV u otro dispositivo de video, se controla el volumen del TV.
Cuando se selecciona un DVD con cine en casa, se puede controlar el volumen.
TV
: Entrada de VIDEO 1
: Entrada de VIDEO 2
: Entrada de HDMI
: Entrada de RGB
: (ENTRADA PIP) Cambia la
entrada de la imagen de la
“ventana”.
: (PIP) Enciende y apaga la
“ventana”.
: (MOVER PIP) Mueve la
ubicación de la imagen de la
“ventana”.
: (PAUSAR PIP) Congela la
imagen de la “ventana”.
: (CAMBIAR PIP) Cambia entre
la imagen “principal” y la “ventana”.
A: Botón rojo
B: Botón verde
C: Botón amarillo
D: Botón azul
LIST: (SUBTÍTULO) Muestra los
subtítulos.
MENU: Muestra el menú.
INPUT: Cambia el modo de
entrada.
1 – 9, 0, ENTER,
(
punto
):
Cambia de canal. Por ejemplo, para
cambiar al canal 5, presione 0 y 5
(o presione 5 y ENTER).
PAGE +/–: (CANAL DE PIP +/–)
PIP CH Cambia el canal hacia
arriba/abajo en la imagen de la
“ventana”.
FAVORITES: Habilita la función
Favorito.
INFO: Muestra información de
programación.
OPTIONS: Muestra el menú de
opciones.
RECALL: Selecciona el canal
seleccionado previamente.
CH +/–: Cambia el canal hacia
arriba/abajo.
Reproductor de Blu-ray Disc/HD-DVD
: Va al capítulo/pista anterior.
: Muestra otra vez brevemente
la escena (Flash –).
: Avanza brevemente la escena
(Flash +).
: Va al siguiente capítulo/pista.
: Rebobina rápidamente.
: Reproduce.
: Avanza rápidamente.
: Graba (para grabadora de BD).
: Pausa.
: Detiene.
A: (CONFIGURACIÓN) Muestra
el menú del sistema/
configuración.
B: (SUBTÍTULO) Cambia el
subtítulo.
C: (AUDIO) Cambia el sonido.
D: (BORRAR) Borra la
configuración.
MENU: Muestra el menú
emergente/menú del disco.
INPUT: Cambia el modo de
entrada.
1 – 9, 0: Botones numéricos
(punto): (+10) Selecciona los
números a partir del 10.
: Abre/cierra la bandeja del disco.
PAGE +: (BD) Selecciona la unidad
de BD.
PAGE –: (HDD) Selecciona el disco
duro interno.
FAVORITES: (MENÚ PRINCIPAL)
Muestra el menú principal.
INFO: (MOSTRAR) Muestra la
información de reproducción.
OPTIONS: Muestra el menú de
opciones.
ENTER: Accede al elemento
seleccionado.
DVR (videograbadora digital)/PVR (videograbadora personal)
: Va a la ubicación anterior.
: Muestra otra vez brevemente
la escena (Flash –).
: Avanza brevemente la escena
(Flash +).
: Va a la siguiente ubicación.
: Rebobina rápidamente.
: Reproduce.
: Avanza rápidamente.
: Graba.
: Pausa.
: Detiene.
A: (VOLVER A REPRODUCIR*)
Habilita la función para volver a
reproducir para DVR/Replay
TV.
B: (Live TV*) Muestra la guía
maestra.
LIST: Muestra el título del
programa grabado.
MENU: Muestra el menú.
INPUT: Cambia el modo de
entrada.
1 – 9, 0: Botones numéricos
(punto): (+10) Selecciona los
números a partir del 10.
: Abre/cierra la bandeja del disco.
PAGE +/–: Avanza/retrocede la
página, Buscar* arriba/abajo
INFO: (MOSTRAR) Muestra la
información de reproducción.
RECALL: Selecciona el canal
seleccionado previamente.
CH +/–: Cambia el canal hacia
arriba/abajo.
ENTER: Accede al elemento
seleccionado.
* Estos botones corresponden al servicio
TiVo o al servicio Replay. Consulte su
manual de instrucciones para obtener
más detalles.
DVD con cine en casa
: Va al capítulo/pista anterior.
: Muestra otra vez brevemente
la escena (Flash –).
: Avanza brevemente la escena
(Flash +).
: Va al siguiente capítulo/pista.
: Rebobina rápidamente.
: Reproduce.
: Avanza rápidamente.
: Graba.
: Pausa.
: Detiene.
A: (CONFIGURACIÓN) Muestra
el menú del sistema/
configuración.
B: (SUBTÍTULO) Cambia el
subtítulo.
C: (AUDIO) Cambia el sonido.
D: (BORRAR) Borra la
configuración.
LIST: Habilita la función CAMPO
DE SONIDO.
MENU: Muestra el menú del DVD.
INPUT: Cambia el modo de
entrada.
1 – 9, 0: Botones numéricos
(punto): (+10) Selecciona los
números a partir del 10.
: Abre/cierra la bandeja del disco.
FAVORITES: (MENÚ PRINCIPAL)
Muestra el menú principal.
INFO: (MOSTRAR) Muestra la
información de reproducción.
OPTIONS: Muestra el menú del
amplificador.
RECALL: (BANDA) Selecciona
FM/AM.
CH +/–: Configura o sintoniza la
frecuencia hacia arriba/abajo.
ENTER: Accede al elemento
seleccionado.
Notas sobre el uso del RM-VZ220
El RM-VZ220 no puede realizar funciones que el dispositivo no está diseñado para
realizar. Por ejemplo, si su TV no tiene una función para silenciar el sonido, la función
MUTING en el RM-VZ220 no funcionará con su TV.
La función de los botones varía dependiendo de los modos de configuración/
operación. La tabla de “Descripción de los botones del control remoto” muestra cómo
el RM-VZ220 opera en general con cada dispositivo en el modo configurado.
Si el decodificador de cable puede controlar el volumen, asegúrese de establecerlo en
un nivel moderado. Si el volumen en el decodificador de cable se baja por completo,
no podrá ajustar el volumen de su TV con el RM-VZ220.
Cable set top box / Decodificador de cable
Brand Code No.
ADB 51927
Bright House 51376, 51877
Cable One 51376, 51877
Cablevision 51376, 51877, 51006
Charter 51376, 51877, 52187
Cisco 51877, 50877, 51982
Comcast 51376, 51877, 51982, 52576
Cox 51376, 51877
Digeo 51187, 52187
Director 50476
General
Instrument
50476
Insight 51376, 51877
Jerrold 50476
Knology 51877
Mediacom 51376, 51877
Brand Code No.
Motorola 51376, 50476, 51187, 51982
NET 50277
Pace 51877, 51982
Panasonic 51982
Philips 51305
Pioneer 51877, 50877
Rogers 51877
Scientific Atlanta 51877, 50877, 50277
Shaw 51376
Sony 51006
StarHub 51927
Suddenlink 51376, 51877
Time Warner 51376, 51877, 52187
Tivo 52576
US Electronics 50277
WideOpenWest 51877
IPTV / IPTV
Brand Code No.
AT&T 50858
Azteca 52237
BesTV 52327
Cisco 52345
Motorola 51998, 50858, 52275, 52378
Reliance 52452
Brand Code No.
Scientific Atlanta 50858, 52345
SingTel 51998, 52275
Thomson 52237
UTStarcom 52327
Verizon 52378
Satellite receiver / Receptor de satélite
Brand Code No.
Airtel 42248
Astro 42600
Bell ExpressVu 40775
DirecTV 41377, 40566, 40749, 40099,
41442
Dish Network 40775
Dishpro 40775
Echostar 40775, 42527
Expressvu 40775
GE 40566
GOI 40775
Hisense 41535
HTS 40775
Hughes Network
Systems
40749, 41442
iLo 41535
Indovision 40856
JVC 40775
Magnavox 40722
Mitsubishi 40749
Brand Code No.
Multichoice 42059, 42060
NET 41883
Net Brazil 41883
Pace 40887
Philips 40749, 40722, 40099, 41442
Proscan 40566
Proton 41535
RCA 40566
Samsung 41377, 41442
SKY 40856, 42619
SKY Brazil 40856, 40887, 41499
SKY Mexico 40856, 42619
Telefonica 42527
Tivo 41442
Toshiba 40749
Uniden 40722
US Digital 41535
USDTV 41535
Zenith 40856
DVR (digital video recorder)/PVR (personal video recorder)
DVR (videograbadora digital)/PVR (videograbadora personal)
Brand Code No.
DirecTV 20739
Go Video 20614
Hughes Network
Systems
20739
Humax 20739
Panasonic 20614, 20616
Philips 20739, 20618
Brand Code No.
ReplayTV 20614, 20616
Samsung 20739
Sonic Blue 20614, 20616
Sony 20636
Tivo 20739, 20618, 20636
Toshiba 21008
VCR / VCR
Brand Code No.
Admiral 60048
Aiwa 60037
Allegro 61137
American High 60035
Audiovox 60037
Calix 60037
Canon 60035
Carver 60081
CineVision 61137
Citizen 60037
Craig 60037
Curtis Mathes 60060, 60035, 60162
Daewoo 61137
Denon 60042
DirecTV 60739
Durabrand 60038
Electrohome 60037
Electrophonic 60037
Emerex 60032
Emerson 60037, 60043
ESA 61137
Fuji 60035, 60033
GE 60060, 60035
Go Video 60614, 61137
GoldStar 60037, 60038, 61137
Gradiente 61137
Harman/Kardon 60081, 60038
Hitachi 60042
Hughes Network
Systems
60739, 60042
Humax 60739
Instant Replay 60035
JVC 60067
KEC 60037
Kenwood 60067, 60038
Kodak 60035, 60037
LG 61137
LXI 60037
Magnavox 60035, 60081
Marantz 60035, 60081
Marta 60037
Matsushita 60035, 60162
MEI 60035
Memorex 60035, 60162, 60037, 60048
MGA 60043
Minolta 60042
Mitsubishi 60067, 60043
Brand Code No.
Motorola 60035, 60048
NEC 60067, 60038
Nikko 60037
Olympus 60035
Optimus 61062, 60162, 60037, 60048
Panasonic 61062, 60035, 60162, 60614,
60616, 61562
Penney 60035, 60037, 60042, 60038
Pentax 60042
Philco 60035
Philips 60739, 60035, 60081, 60618
Pilot 60037
Pioneer 60067
Polk Audio 60081
Proscan 60060
Quasar 60035, 60162
Radix 60037
Randex 60037
RCA 60060, 60042
Realistic 60035, 60037, 60048
ReplayTV 60614, 60616
Rio 61137
Samsung 60739
Sanky 60048
Sansui 60067
Scott 60043
Sears 60035, 60037, 60042
Sensory Science 61155
Sharp 60048
Sonic Blue 60614, 60616, 61137
Sony 60032, 60033, 60636
STS 60042
Sylvania 60035, 60081, 60043
Tashiko 60037
Technics 60035, 60162
Teknika 60035, 60037
Tivo 60739, 60618, 60636
Toshiba 60043, 61008
Totevision 60037
Vector Research 60038
Videomagic 60037
Wards 60060, 60035, 60048, 60081,
60042
XR-1000 60035
Yamaha 60038
Zenith 60033, 61137
DVD Home Theater / DVD con cine en casa
Brand Code No.
Anam 31609
Bose 31229, 31629, 31933
Denon 32857
Harman/Kardon 31306
HitPlus 32483
Insignia 31751, 32175
Integra 31298
JBL 31306
JVC 31374, 32239, 32331
LG 31293, 32197, 32284
Magnavox 31514
NexxTech 31751
Norcent 31751
Brand Code No.
Onida 32482
Onkyo 31298, 31531
Panasonic 31288, 31548, 31633, 31763,
31764, 32452, 32967
Philco 31838
Philips 31266, 32311, 32459
Pioneer 31935
RCA 31609, 32041, 32426
Samsung 31295, 31500, 31868
Sony 31622, 31558, 31658, 31758,
31822, 31858, 32522
Vtrek 32426, 32483
Zenith 31293
-
1
-
2
Sony RM-VZ220 User manual
- Category
- Portable DVD/Blu-Ray players
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Vidao V7 User manual
-
Hisense Infinity E6 Hard reset manual
-
Coby DVDR-1100 Troubleshooting Instructions
-
COBY electronic DVDR-1100 User manual
-
-
Trojan Air Rope Owner's manual
-
Epson Bocs User manual
-
Speed Passion RS2 User manual
-
Gateway XHD3000 User manual
-
