SAM Electronics GmbH QO7NG3029S30KW User manual

Brand: SAM Electronics GmbH

Model: QO7NG3029S30KW

Type: User manual

This manual is also suitable for

Operating Instructions

RADARPILOT ATLAS 1000

CHARTRADAR ATLAS 1000

MULTIPILOT ATLAS 1000

Software Version 2.4

Radar Functions

Plotting Aids

Item No.: ED 3038 G 232 Revision: 01 (2002-06) Order No.: 300004937

b_r1_eti.fm / 21.06.02

This document is our property for which we reserve all rights, including

those relating to patents or registered designs. It must not be

reproduced or used otherwise or made available to any third party without

our prior permission in writing.

Alterations due to technical progress are reserved.

STN ATLAS Marine Electronics GmbH

D - 22763 Hamburg

Service

Customer Support Center

Phone: + 49 (0) 18 03 00 85 53

Fax: + 49 (0) 18 03 00 85 54

E-mail: shipservice@sam-electronics.de

ED 3038 G 232 / 01 (2002-06)

Operating Instructions General Safety Precautions

b_r1_esh.fm / 21.06.02

RADARPILOT / CHARTRADAR

General Safety Precautions

The radar can perform its safety function if, and only if, the transmission power and the receiver sensitivity

are adequate. Therefore, these characteristics must be checked regularly (by means of the Performance

Monitor – see Section 21).

Connected position receivers must fulfil the standard IEC 61162-1 1).

ARPA target data are directly dependent upon the accuracy and proper functioning of the selected speed

sensor and the gyro compass.

DANGER: High frequency radiation

Persons must definitely avoid being present in the radiation danger zone

of the rotating antenna.

In the case of work being done on the antenna unit, the antenna switch

situated there must be set to 0 and the transceiver must be discon-

nected from the ship’s mains.

☞There is no international agreement about the danger posed by high frequency radiation of the kind

produced by the radar systems. In most countries, a radiation density exceeding 100 W/m2 is consid-

ered to be dangerous; in some countries, values over 10 W/m2 are regarded as not being completely

safe.

1) IEC 61162-1 largely corresponds to NMEA 0183 Version 2.30 of 1st March 1998.

Antenna Type Transceiver

A=Up B=Down

Radius of the Radiation Danger Zone

Radiation Density

100 W/m2Radiation Density

10 W/m2

5 ft X-Band 12.5 kW, Version A 1.4 m 14 m

25 kW, Version B 1.65 m 16 m

8 ft X-Band 12.5 kW, Version A 0.65 m 7 m

14 ft S-Band 30 kW, Version A 1.3 m 13 m

30 kW, Version B 0.7 m 7.8 m

Particular attention must be paid to the notes and warnings refer-

ring to possible faults in the radar display, since such faults can

impair the detection of targets.

RADARPILOT / CHARTRADAR

ED 3038 G 232 / 01 (2002-06)

Operating Instructions

General Safety Precautions

b_r1_esh.fm / 21.06.02

DANGER: Injury caused by a rotating antenna

When the radar system is switched to "ON", it is possible that, instead

of the expected antenna, a different one will begin to rotate. Therefore, it

must be ensured beforehand that all antennas can rotate freely and that

are no persons near the antennas.

The units may be opened only by qualified, trained persons.

DANGER: Dangerous voltage

Even when the equipment is switched off, there can be a dangerous

voltage present at exposed contacts in the units. Therefore, before a unit

is opened, it must be ensured that the voltage supply to the unit is

disconnected from the ship’s mains, and that it remains disconnected.

Because of the capacitors contained in the units, there can be a

dangerous voltage present in any unit even several minutes (or several

hours in the case of monitors) after switching off and disconnection

from the power supply.

☞If the units are to be disconnected from the ship’s mains, it must be remembered that each antenna

unit, each transceiver electronics unit and each indicator normally has its own supply of power from

the ship’s mains.

If, for the transfer of signals (e.g. transfer of the heading signal from the compass system), synchro

transmitter are used, a dangerous voltage exists in the units until the reference voltage is switched

off.

ED 3038 G 232 / 01 (2002-06)

Operating Instructions List of Contents

b_r1seiv.fm / 21.06.02

RADARPILOT / CHARTRADAR

List of Contents

☞Please pay attention to the supplement (if any) at the end of the document.

General Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

List of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.1 RADARPILOT ATLAS 1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.2 CHARTRADAR ATLAS 1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.3 MULTIPILOT ATLAS 1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.4 The Equipment Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.5 Scope of Applicability of these Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2 Basic Settings; General Remarks about Operating . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.1 Switching the Radar System On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.2 General Remarks about the Operating and Display Elements . . . . . . . . . . . . . . . . . . . . . . 16

2.3 Brilliance and Colour Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.4 Degaussing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2.5 Display Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.6 An Overview of the Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2.7 The Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

2.8 Activating/Deactivating of Slave Keyboards/Trackballs . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

3 PPI Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion . . . . . . . . . . . . . . . . . . . . . . 29

3.2 PPI Orientation: Head-Up, North-Up, Course-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

3.3 Centering / Off-Centering of the Display (Center, Off-Center) . . . . . . . . . . . . . . . . . . . . . . 31

3.4 Range Selection (Range) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

3.5 Range Rings, Grid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots . . . . . . . . . . . . . . 32

3.7 Trails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

3.8 Setting the Display of Pre-planned Tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

3.9 Defining the System Track and the Next Waypoint; System Track Display . . . . . . . . . . . 39

3.10 Setting the Display of User Chart Objects on the RADARPILOT . . . . . . . . . . . . . . . . . . . . 41

3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR . . . . . . . . . 42

3.12 Setting the Display of the Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

3.13 Adjusting the Chart or Map to the Radar Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

4 Setting the Radar Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over . . . . . . . . . . . . 47

4.2 Basic Setting of the Radar Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

4.3 Selection of the Antenna Revolution Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

4.4 Radar Setting for High Speed of Own Vessel (HSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

RADARPILOT / CHARTRADAR

ED 3038 G 232 / 01 (2002-06)

Operating Instructions

List of Contents

b_r1seiv.fm / 21.06.02

4.5 Radar Setting for the Display of RACON Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

4.6 Radar Setting for SART Detection (X-Band only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

4.7 Suppression of the Synthetics and Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

5 Heading, Speed, Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

5.1 Compass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

5.2 Speed Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

5.3 Position Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

6 Bearing and Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

6.1 Cursor Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

6.2 Variable Range Markers (VRM’s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

6.3 Electronic Bearing Lines (EBL’s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

6.4 Operating the VRM and the EBL Jointly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

6.5 Parallel Index Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

7 ARPA Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

7.1 Symbols Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

7.2 Procedure of the Target Acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

7.3 Manual Target Acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone . . . . . . . . . . . . . 69

7.5 Deletion of Targets, Loss of Target . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

7.6 Target Data Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

7.7 Target Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

7.8 Selecting the Reference Targets for Reference Target Tracking . . . . . . . . . . . . . . . . . . . 73

8 EPA Functions (Electronic Plotting Aid) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

8.1 Manual Target Acquisition and Semi-Automatic Plotting . . . . . . . . . . . . . . . . . . . . . . . . . . 75

8.2 Deletion of Targets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

8.3 Target Data Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

8.4 Target Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

9 Collision Avoidance (TCPA, CPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

10 Trial Manoeuvres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

10.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

10.2 Switch-On of the Trial Manoeuvre Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

10.3 Setting the Trial Manoeuvre in Relative Display Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

10.4 Checking the Trial Manoeuvre in True Display Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

10.5 Switching Off the Trial Manoeuvre Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

11 Editing of Pre-planned Tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

11.1 Generating a New Pre-planned Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

11.2 Modifying an Existing Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

11.3 Generating a New Track on the Basis of an Existing Track . . . . . . . . . . . . . . . . . . . . . . . 90

ED 3038 G 232 / 01 (2002-06)

Operating Instructions List of Contents

b_r1seiv.fm / 21.06.02

RADARPILOT / CHARTRADAR

11.4 Managing the Pre-planned Tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

12 Editing the Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

12.1 Preparing the Editing of the Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

12.2 Editing of Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

12.3 Editing of Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

12.4 Ending the Editing of a Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

13 Displays in the Multidisplay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

13.1 Docking Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

13.2 Zoom Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

13.3 Depth Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

13.4 Wind/Set+Drift Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

14 Quick Info Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

14.1 Contents of the Quick Info Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

14.2 Operating Procedure for the Stopwatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

14.3 Setting the Zone Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

15 Evaluation of the Radar Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

15.1 Achievable Radar Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

15.2 Distortions of the Radar Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

15.3 Undesirable Echo Displays and Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

15.4 Sector Blanking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

16 The Radar Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

17 Alarm Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

18 List of Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

19 List of the Alarm Signal Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

20 Care and Maintenance Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

20.1 Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

20.2 Maintenance Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

21 Performance Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

22 System Maintenance Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

22.1 Determining the Versions of Software, Hardware and Documentation . . . . . . . . . . . . . . 134

22.2 Listing the System Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

22.3 Off-Line Selfcheck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

22.4 Checking / Correcting the Computer Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

22.5 Distribution and Deletion of Map Data; Data Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

RADARPILOT / CHARTRADAR

ED 3038 G 232 / 01 (2002-06)

Operating Instructions

List of Contents

b_r1seiv.fm / 21.06.02

22.6 Exchanging Track Files between the Indicators; Data Saving . . . . . . . . . . . . . . . . . . . . 143

22.7 The Handling of Diskettes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

22.8 Aborting and Restarting the Program of the Radar System . . . . . . . . . . . . . . . . . . . . . . 144

Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177

ED 3038 G 232 / 01 (2002-06)

Operating Instructions

1 Overview

1.1 RADARPILOT ATLAS 1000

b_r1_e11.fm / 21.06.02

RADARPILOT / CHARTRADAR

1 Overview

Subjects of this Section:

◆Brief overview of the parts of the system

◆Optional parts and functions

The radar system can be configured in two main versions:

- the basic version, called RADARPILOT ATLAS 1000

- an expanded version, called CHARTRADAR ATLAS 1000 (or MULTIPILOT ATLAS 1000, see

Section 1.3) which, in addition, offers the possibility to display selected parts of the Electronic Chart

on the radar screen in an alternative display mode.

Both versions are approved according to the published radar performance standards.

1.1 RADARPILOT ATLAS 1000

From the components of the RADARPILOT, it is possible to assemble radar sets and radar systems for

all types of ship.

In a RADARPILOT System, the following components can be combined with each other in any desired

manner:

- X-Band or S-Band transceiver and antenna

- Electronics Units with manual (EPA) or automatic (ARPA) plotting aids.

- 12" or 16" indicators

- Radar indicators as console versions or desk-top versions

The scope ranges from single systems to multiple systems consisting of five transceivers and five indica-

tors.

Not only the system configuration but also the manner of use is extremely flexible: with just a few oper-

ating steps, each radar indicator can be switched to act as the master indicator of any desired transceiver

or as a slave for any transceiver that is operating (interswitch function).

☞On the master indicator, all functions of the radar can be operated, i.e. both on the transmitter side

and on the receiver side. On the slave indicator, most functions on the reception side can be set

independently of the master.

All radar sets are suitable for high speed craft (HSC’s) too (if the antenna gearboxes are chosen appro-

priately), and on ships with normal speed they can be operated at twice the antenna rotation rate if this

is required by the situation.

1.2 CHARTRADAR ATLAS 1000

The CHARTRADAR consists of the same components as those of the RADARPILOT, and also has all

the characteristics of the RADARPILOT. In addition, it offers the possibility that the vector charts which

exist in the CHARTPILOT can be displayed on the radar. 1)

1) From the point of view of approval, the CHARTRADAR can be configured at service level in such a way that it fulfils the regulation IEC

60936-1, "Shipborne Radar" or the regulation IEC 60963-3, "Radar with Chart Functions". In the latter case, there are limitations in the

display of the chart - see footnotes on page 30 and page 43.

RADARPILOT / CHARTRADAR

ED 3038 G 232 / 01 (2002-06)

Operating Instructions

1 Overview

1.3 MULTIPILOT ATLAS 1000

b_r1_e11.fm / 21.06.02

The Electronic Charts are vector charts which are provided by a CHARTPILOT ATLAS 93xx via a data

bus connection.

A CHARTPILOT is therefore necessary for operation of the CHARTRADARs, but is also used together

with RADARPILOTs. CHARTPILOT and CHARTRADAR or RADARPILOT exchange a large quantity of

data with each other, especially relating to the navigation sensors, the tracks, and the alarms that are

generated by the ECDIS which is contained in the CHARTPILOT.

1.3 MULTIPILOT ATLAS 1000

The MULTIPILOT ATLAS 1000 has a different Electronics Unit. There, it can be specified at service level

whether the MULTIPILOT is to perform the functions of the CHARTRADAR or those of the CHART-

PILOT 1).

In the first case, the MULTIPILOT ATLAS 1000 does not differ from the CHARTRADAR as far as the

operating procedure and the functions are concerned. All statements made about the CHARTRADAR in

these Operating Instructions are also applicable to the MULTIPILOT ATLAS 1000.

In the second case, the MULTIPILOT ATLAS 1000 does not differ from the CHARTPILOT ATLAS 9330

as far as the operating procedure and the functions are concerned - see Operating Instructions ED 3032

G 232.

1.4 The Equipment Components

The radar systems (RADARPILOT and CHARTRADAR) consist of two segments which are connected to

one another via bus systems (CAN Bus) etc. These segments are the radar indicator and the transceiver/

antenna.

The radar indicator is the central operating and display unit. It consists of

- the monitor, with a high-resolution 21" colour screen for the 12" radar or a 29" colour screen for the

16" radar,

- the trackball, with which all operating inputs can be made,

- the radar keyboard, with which operating steps that are frequently used can be carried out particu-

larly conveniently by means of function keys and rotary knobs,

- the diskette drive, which permits very easy servicing and makes it possible to save data and to

exchange data with radar systems installed on other ships, and

- the display electronics unit, the heart of which consists of a high-performance computer which also

performs the communication with the display electronics units of the other radar sets installed. In

addition, the interface adaptation for navigation sensors having NMEA interfaces takes place here.

- On the radar interconnection box, all ship’s cables leading to the radar indicator are connected. If

necessary, special Interface electronics is also accommodated here.

The parts of the radar indicator are usually integrated within a console. However, they can also be

assembled as a desk-top version without integrating the display electronics and the interconnection box.

The display electronics unit is then installed together with the radar interconnection box to form a single

unit.

1) In a future version, this selection will be made by means of the normal operating procedure.

ED 3038 G 232 / 01 (2002-06)

Operating Instructions

1 Overview

1.5 Scope of Applicability of these Operating Instructions

b_r1_e11.fm / 21.06.02

RADARPILOT / CHARTRADAR

In addition,

-slave monitors can be installed, which repeat the display shown by the indicator to which they are

connected.

-slave keyboards or slave trackballs can be installed. Each slave keyboard or slave trackball is

assigned to a slave monitor. For each slave keyboard/trackball, there is an electronics unit called a

keyboard switch which, by means of a single operating step, makes it possible to assign the oper-

ating functions to a slave keyboard (trackball) / slave monitor pair.

-a video buffer is used, if there is more than one slave monitor connected to an indicator.

The RF components are

-the transceiver (electronics unit), which contains the X-Band transceiver or the S-Band transceiver

(transceiver version B = bulkhead), and

-the antenna (unit), consisting of

-the antenna gearbox (X-Band or S-Band) and

-the scanner (5 ft X-Band or 8 ft X-Band scanner or 14 ft S-Band scanner).

The transceiver can also be accommodated in the antenna gearbox, so that there is no need for a

separate transceiver electronics unit (transceiver version A = antenna/mast ahead).

In addition, a unit called

-the Interface Expander may be present. When there are more than two radar indicators or more

than two transceivers installed, the switch-over between the indicators and transceivers is performed

by the Interswitch installed in the Interface Expander. If additional interfaces or interfaces having a

non-standardised format have to be implemented, the electronics which is additionally installed in the

Interface Expander performs the necessary interfacing and data distribution.

Examples of various equipment configurations are given in the following illustrations.

☞The TVA 1) signals entered there are the combined reception signals of the transceivers. In the indi-

cators, these signals are used to generate the radar video signal, as well as the trigger signals and

antenna signals.

1.5 Scope of Applicability of these Operating Instructions

These operating instructions cover all of the above-mentioned variants of the RADARPILOT and CHAR-

TRADAR equipment and systems. It refers to RADARPILOT ATLAS 1000 and CHARTRADAR ATLAS

1000 systems which are approved under the software version stated on the title page. 2)

☞Unless the RADARPILOT or CHARTRADAR or MULTIPILOT is mentioned specifically, all state-

ments made in these Operating Instructions apply to these types of equipment.

1) TVA = Trigger, Video, Azimuth

2) On page 134, there is a description of how the software version of the radar system can be displayed.

RADARPILOT / CHARTRADAR

ED 3038 G 232 / 01 (2002-06)

Operating Instructions

1 Overview

1.5 Scope of Applicability of these Operating Instructions

b_r1_e11.fm / 21.06.02

Example of a single installation with minimum scope

A typical dual installation (IMO pair)

Display

electronics unit

Radar

TVA

X-Band antenna unit

with 5 ft scanner and

transceiver

CAN Bus

Navigation

sensors

12" EPA

radar indicator

Desk-top version

interconnection box

S-Band antenna unit with 14 ft scanner and transceiver

X-Band TVA

X-Band antenna unit

with 8 ft scanner

S-Band TVA

CAN Bus

16" EPA 16 " ARPA

TVA TVA

radar indicator radar indicator

Navigation

Alarm system

sensors

Redundant /

navigation

additional

sensors

Display

electronics unit

Radar

Transceiver

electronics unit

interconnection box

Display

electronics unit

Radar

interconnection box

ED 3038 G 232 / 01 (2002-06)

Operating Instructions

1 Overview

1.5 Scope of Applicability of these Operating Instructions

b_r1_e11.fm / 21.06.02

RADARPILOT / CHARTRADAR

Radar system and CHARTPILOT

Display

electronics unit

Interface

Interswitch

expander

CAN Bus

Ethernet LAN

TVA

Radar

CAN Bus

TVA

Radar indicator Radar indicator

CHARTPILOT

Printer

Digitizer

Transceiver

electronics unit

CHARTPILOT

electronics unit

Navigation

Bridge alarm system

Gyro

Position 2

Log 2

sensors

other sensors,

interfaces

(Example)

Gyro

Log 1

Position 1

non-standardised

Echosounder

S-Band antenna unit X-Band antenna unit

with 5 ft scanner and

transceiver

with 14 ft scanner

X-Band antenna unit

with 8 ft scanner and

transceiver

interconnection box

Display

electronics unit

Radar

interconnection box

with standardised or

Slave monitor

Keyboard

switch

Slave trackball

Stb wing:

Slave monitor

Keyboard

switch

Slave trackball

Port wing:

RADARPILOT / CHARTRADAR

ED 3038 G 232 / 01 (2002-06)

Operating Instructions

1 Overview

1.5 Scope of Applicability of these Operating Instructions

b_r1_e11.fm / 21.06.02

ED 3038 G 232 / 01 (2002-06)

Operating Instructions

2 Basic Settings; General Remarks about Operating

2.1 Switching the Radar System On and Off

b_r1_e12.fm / 21.06.02

RADARPILOT / CHARTRADAR

2 Basic Settings; General Remarks about Operating

Subjects of this Section:

◆Switching the radar system on and off

◆General remarks about the operating and display elements

◆The trackball and its keys

◆General remarks about menus

◆The input of numerical values and text

◆Brilliance and colour settings, degaussing

◆Display modes

◆Overview of the screen

◆The menu structure

2.1 Switching the Radar System On and Off

Switching the radar system ON is done by means of one of the ON/OFF switches or

POWER buttons situated on the radar indicators. When this is done, all indicators and

transceivers are switched on. 1) and

After the warm-up phase of the magnetron - 3 minutes for X-Band and 3.5 minutes for S-Band - stand-

by operation is achieved and the radar function can be switched on; see page 47.

☞The act of switching an indicator on never causes a transceiver to be switched directly into radar

Mode.

☞If an attempt to switch over to radar operation occurs before stand-by operation is achieved, the indi-

cation WARM UP appears instead of the list of transceivers.

Switching the radar system OFF: Switch off all indicators by means of the ON/OFF switch 2). As long

as there is one of the switches in the ON state, all electronics units of the indicators and transceivers

remain switched on and.

Stand-By Operation

The main difference between stand-by operation and radar operation is that, during stand-by operation,

the transceiver is not transmitting and the antenna is not rotating. Therefore, the radar video is absent on

the PPI, and none of the functions that depend on the transceiver can be operated yet.

During stand-by operation, the magnetron is kept at its operational temperature.

1) If an display electronics unit is exposed to very low temperatures (around -15°C or less), it can happen that its computer does not start up.

The screen of the associated monitor then remains dark, or becomes dark after a short time. In this case, the radar system must remain

switched on for about 30 minutes (in spite of the dark screen) so that the display electronics units will warm up. If the radar system is then

switched off and is switched on again after a waiting time of a few seconds, the computer will start up in the normal way.

2) If a indicator has a POWER key, that indicator is switched off by prolonged pressing of this key.

RADARPILOT / CHARTRADAR

ED 3038 G 232 / 01 (2002-06)

Operating Instructions

2 Basic Settings; General Remarks about Operating

2.2 General Remarks about the Operating and Display Elements

b_r1_e12.fm / 21.06.02

2.2 General Remarks about the Operating and Display Elements

On the indicators of the radar system, many screen display fields also act as switching areas or input

fields which can be operated quickly and intuitively by means of the trackball and cursor.

With these few elements, the entire radar system can be operated from the radar indicator with the aid

of its trackball. In addition, the optional radar keyboard contains function keys and rotary knobs for direct

access to some functions that are needed frequently.

☞The description of the operating procedure in these Operating Instructions normally refers to the

trackball and cursor. In Section 16, the operating procedure using the optional radar keyboard is

summarised.

Trackball and Cursor

☞If you are already familiar with graphic man-machine inter-

faces, you might be able to skip this section. Before doing so,

you should have a look at the picture of the trackball beside

this text.

Every operating step begins with the operator moving the cursor

by means of the trackball to a particular place on the screen (to a

text item, a numerical value, a symbol on the PPI or any desired

place on the PPI). The next step is always the pressing of one of

the trackball keys. In the following, this brief pressing of the key is

called clicking. What then happens depends on the key used, the

element on which clicking took place, and the operating situation,

and is the subject of these operating instructions.

The cursor has a resting position to which it goes 30 seconds after the last operating process. This

position is situated beside the PPI, below the ACQ TGT area.

If the cursor is situated outside the PPI, it is shaped like a hand or an arrow. Inside the PPI, it is a set of

crosswires.

The trackball has three keys with two different functions:

DO Key

The most important key is the middle (bigger) one. Almost all data areas react to this key, which performs

the functions that are needed the most frequently. In these operating instructions, it is called the "DO

key". In the following, "clicking" always means clicking with the DO key unless stated otherwise.

MORE Keys

The two keys situated above the DO key are called "MORE keys" in these operating instructions. They

have identical functions 1) which are not needed as frequently. Not all elements which can be operated by

means of the DO key react to the MORE key also, and if they do, then always with functions other than

those of the DO key. Furthermore, by pressing of the MORE key, open menus (for menus, see below)

can generally be closed without any results, and inputs can be aborted.

Data Areas

Some data areas are used only to display numerical values, names or stati.

Example: Target data display

In the case of most data areas, the operating procedure for the functions displayed there is likewise

performed by clicking on the data area.

1) There are two "MORE" keys so that both left-handed people and right-handed people can operate them ergonomically. Their functions are

identical.

DO key

MORE key...

for left-handed

people

for right-handed

people

ED 3038 G 232 / 01 (2002-06)

Operating Instructions

2 Basic Settings; General Remarks about Operating

2.2 General Remarks about the Operating and Display Elements

b_r1_e12.fm / 21.06.02

RADARPILOT / CHARTRADAR

Examples:

- Two switch Acquisition/Guard Zone 1 on and off, all that you need to do is to click on the AK / GZ1

button 1).

- If the transfer of the course is to be synchronised, click on the currently existing heading value. A

numeric keyboard is then displayed. Input the correct value by means of that keyboard.

And so on.

Basically, the following is true:

Coloured data areas indicate the activated state.

In the case of functions which only have an "on" state and an "off" state, the "on" state is indicated by a

coloured background. Example: IR on a grey background means that Interference Rejection is not

switched on; IR on a coloured background means that it is switched on.

Areas that are flashing in colour signify that the corresponding function (e.g. ACQ TGT, ADJUST etc.)

can be executed.

Sensitive and Insensitive Data Areas

Data areas that can be operated can be insensitive in particular operational states, i.e. they cannot be

operated. For example, after clicking on the TUNE area, tuning can be performed on the master indicator,

but not on a unit switched to act as a slave indicator. On the slave indicator, the TUNE area is displayed

as being insensitive.

☞Insensitive data area can be recognised from their low-contrast lettering or colouring.

Before pressing of the DO or MORE key, sensitive data areas can be recognised from the black

border which indicates the boundary of the sensitive area as soon as the cursor is situated in this

region. Furthermore, the shape of the cursor changes to that of a hand.

Operating Procedure for the Context Menus

Particular data areas react to clicking by presenting a list of further possibilities - the "context menu", as

it is called. If clicking takes place on one of the buttons contained in the context menu, the corresponding

change in the function takes place and the context menu disappears. In some cases, a further menu is

opened. By clicking on the background area, the context menu can be switched off without any change

of function.

☞ 30 seconds after the last operating process, the context menu switches off automatically.

The Function of the Menu Buttons

Clicking on the buttons MENU to BRILL situated at bottom right

opens menus in which basic settings can be made and which

contain other functions that are not needed very often. Most of

these menus contain several levels, i.e. from the menu that has

been called up, a submenu can be called up, and so on. The higher

levels are listed in the menu header. There, you can return to the

higher level by clicking. Clicking on the highest level or on the

menu button having the same name closes the menu.

☞30 seconds after the last operating process on the menu, it

switches itself off automatically.

☞The complete structure of the menu system is shown in

Section 2.7.

1) Data areas which produce an effect as a result of clicking are also called buttons in the following.

ZOOM

DOCKING

DEPTH

UTILITIES...

HELP

2.DO

USER SETTINGS...

USER SETTINGS

1.DO

BUZZER

DGPS ONLY

back: DO

USER SETTINGS

off: DO

RADARPILOT / CHARTRADAR

ED 3038 G 232 / 01 (2002-06)

Operating Instructions

2 Basic Settings; General Remarks about Operating

2.2 General Remarks about the Operating and Display Elements

b_r1_e12.fm / 21.06.02

The hidden OTHER button

To switch over the content of entire areas of the screen, e.g. the area containing the Multidisplay or the

radar target data, the OTHER button is used; this button is not continuously visible.

The OTHER button appears in miniaturised form in the top left-hand corner of the display as soon as the

cursor is situated in the relevant display. It appears in normal form as soon as the cursor is situated in

the area of the normal display of the OTHER button. By clicking of this button, a context menu with the

possible display-settings opens up.

Input of Numerical Values

In some areas, numerical values can be entered. This is done with the aid of a virtual keyboard which

appears on the screen as soon as clicking is performed on an area of this kind. With the MORE key, the

input can be aborted without any change occurring.

It is possible to choose between the input of a new value and the changing of the existing value. An

exception to this rule is the input of geographical coordinates, for which different algorithms are appli-

cable.

Entering of a New Value

1. Click on the numerical area; a virtual input-keyboard is

opened.

2. Click numerals one after another. They appear in the display

area of the keyboard.

☞Before the decimal places, click on the point button,

unless the point is entered automatically.

☞Signs, e.g. for the time zone, can be entered by means

of the button .

☞With the button , the character situated on the right in the display area can be deleted.

3. By clicking on the OK button, the value displayed is taken over and the keyboard disappears.

Changing of an Existing Value

1. Click on the numerical area; a virtual input-keyboard is

opened.

2. With the first pressing of the or button, the value

which exists at that time appears in the display area of the

keyboard.

As long as the button of the virtual keyboard is kept

pressed (with the DO key), the existing value increases. As

long as the button is kept pressed, it decreases.

3. By means of the OK button, the keyboard is made to disappear and the value entered is taken over.

NEW

STARBOARD

BUOY, LATER

OTHER

ZOOM

TRIAL MANOEUVRE

TRACK SYSTEM

EDIT MAP

OTHER

Area to be

switched over

2.DO

HDG 087. 5

1.DO

Input

3.DO

Take-over:

4 5 6

7 8 9

0 .

1 2 3

087.5

Increasing

Decreasing

the value

4 5 6

7 8 9

0 .

1 2 3

ED 3038 G 232 / 01 (2002-06)

Operating Instructions

2 Basic Settings; General Remarks about Operating

2.2 General Remarks about the Operating and Display Elements

b_r1_e12.fm / 21.06.02

RADARPILOT / CHARTRADAR

Input of Geographical Coordinates

1. Click on the numerical area; a virtual input-keyboard is

opened.

Here, the existing value appears on the display area of the

keyboard. Instead of the and buttons, the keyboard

has the buttons needed for the input of the relevant hemi-

sphere.

2. By the input of numerals, the existing value is overwritten, beginning at the most significant figure.

3. With the "point" button, you go from the "degrees" part to the "minutes" part, from there to the "thou-

sandths of a minute" part, and from there to the W/E, N/S input part.

4. By clicking on the OK button, the value displayed is taken over and the keyboard disappears.

Input of Texts

In some fields, a text line consisting of large and small

letters, numerals and punctuation marks can be entered.

The process corresponds to new input of numbers - see

above.

The virtual keyboard which appears after the clicking of

these fields is similar to the usual (English) computer

keyboard:

- By means of the Caps button, a switch-over between

large and small letters takes place.

- By means of the Shift button, all characters are

switched over.

- By means of the button, the character situated on

the right in the display field is deleted.

- The input is completed by clicking on the OK button.

Help Function

As soon as the cursor is situated on an area that can be operated,

the function of the DO key and (if applicable) the function of the

MORE key are displayed in the Quick Info Box at the bottom of the

picture if the Help function is switched on.

Switching the Help Function On and Off

Click on the MENU button, and then, in the USER SETTINGS

menu, click the HELP button.

4 5 6

7 8 9

0 .

1 2 3

008: 36. 437 W

9 0 –6 7 83 4 5‘ 1 2 =

o p [y u ie r tTab q w ]

l ; ’h j kd f g

Caps

a s

. /

Space

n m ,c v b

Shift

z x

( ) _^ & *# $ %~ ! @ +

O P {Y U IE R TTab Q W }

L : "H J KD F G

Caps

A S

> ?

Space

N M <C V B

Shift

Z X

USER SETTINGS

1.DO

HELP

3.DO

2.DO

RADARPILOT / CHARTRADAR

ED 3038 G 232 / 01 (2002-06)

Operating Instructions

2 Basic Settings; General Remarks about Operating

2.2 General Remarks about the Operating and Display Elements

b_r1_e12.fm / 21.06.02

Operating Procedure for the Lists

Lists are used for selection and display of the elements

contained in them. Marking of a list element is done by

clicking.

If the list contains more entries than can be simultaneously

displayed, it can be scrolled line-by-line by means of the

and buttons and from page to page by means of

the and buttons, or by clicking below or above the

scroll bar. Alternatively, click on the scroll bar and scroll by

means of the trackball.

Lists often indicate the files which are contained in a catalog.

For example, the list shown here indicates the files of tracks

which are contained in the catalog ATLANTIC. Other catalogs

too can exist. By clicking on the button, the higher level

is displayed, i.e. in this example the list of the catalogs.

☞Many lists also have a search function: If you click into the input field (at the top of the list), the

virtual keyboard which then opens up enables you to enter the number or the beginning of the name

of the list entry that is being searched for. If you click on ENTER, the list jumps to the entry that is

being searched for.

Special Features of the Lists of the System Maintenance Manager

The System Maintenance Manager, a subroutine which was created

for maintenance purposes and which the operator too needs from

time to time (see page 133), uses a different form of list which is

similar to that of other operating systems. Important special features

are:

Catalogs and files of the various levels are contained in one and the

same display.

Catalogs are designated by the symbol or , and files by the

symbol .

A minus sign in the square in front of the catalog symbol shows that

the catalog content is displayed. Clicking on a square with a plus

sign causes display of the catalog content.

☞At the top of the list, the character "/" stands for the root (the

basic list). Marking of this entry selects the sum of all catalogs

and files that are present in the list.

Load Track(s)

No.

/ATLANTIC

4a.DO

Name

BRIXAM-MIAMI 5

BRIXAM-MIAMI 2

FREEPORT-MIAMI

FREEPORT-MIAMI 1

BRIXAM-MIAMI 1

HELSINKI-BRIXAM

BRIXAM-MIAMI 3

BRIXAM-FREEPORT

1306

1305

1307

1308

1302

1301

1303

1304

Scroll bar

Page is loading ...

SAM Electronics GmbH QO7NG3029S30KW User manual

Brand: SAM Electronics GmbH

Model: QO7NG3029S30KW

Type: User manual

This manual is also suitable for

Download PDF

report

SAM Electronics GmbH QO7NG3029S30KW User manual

This manual is also suitable for

SAM Electronics GmbH QO7NG3029S30KW User manual

Related papers

Other documents