Fluke Calibration PPCH Instruction Sheet

Type
Instruction Sheet

Fluke Calibration PPCH is a high-performance hydraulic pressure controller designed to provide accurate and stable pressure control for a wide range of applications. With its ability to generate and control pressures up to 10,000 psi (690 bar), the PPCH is ideal for testing and calibrating pressure transducers, gauges, and other pressure-related devices.

The PPCH features a precision pressure regulator that provides excellent pressure stability and accuracy. The controller also includes a built-in pressure gauge that allows users to monitor the pressure output. Additionally, the PPCH has a variety of input and output connections that make it easy to connect to different types of pressure devices.

Fluke Calibration PPCH is a high-performance hydraulic pressure controller designed to provide accurate and stable pressure control for a wide range of applications. With its ability to generate and control pressures up to 10,000 psi (690 bar), the PPCH is ideal for testing and calibrating pressure transducers, gauges, and other pressure-related devices.

The PPCH features a precision pressure regulator that provides excellent pressure stability and accuracy. The controller also includes a built-in pressure gauge that allows users to monitor the pressure output. Additionally, the PPCH has a variety of input and output connections that make it easy to connect to different types of pressure devices.

PN 3152862
April 2014
© 2014 Fluke Corporation. All rights reserved. Specifications are subject to change without notice.
All product names are trademarks of their respective companies.
HIGH PRESSURE FILTER KIT, INCLUDES:
DESCRIPTION QTY PART NO.
High Pressure Filter 1 103739
Instruction Sheet 1 560083
INTRODUCTION
The High Pressure Filter (see Figure 1) is intended for use
with the PPCH Hydraulic Pressure Controller. The filter
connects to either a stand alone PPCH (see Figure 2) or to
a PPCH with a PG7302 (see Figure 3). This document
contains instructions for connecting the fittings and tubing
for optimal proper performance.
The filter has DH500 fittings at either end. This is the same
type of fitting that is on the PPCH TEST port. It is important
that the filter be positioned and oriented as shown in Figure
2 and Figure 3. In particular, the filter should not be installed
between the PPCH and the PG7302 piston gauge.
CLEANING OR REPLACING THE FILTER
Depending on operating conditions, the filter may become
filled with contaminants from the test circuit. This means the
filter is doing its job.
If the filter shows signs of reduced flow, the filter should be
replaced with a new filter. Alternatively the filter may be
backwashed to remove contaminants, however
backwashing must be done very carefully to avoid
introducing contaminants to the PPCH. The safest
backwash method is to disconnect the inlet (DUT side) of
the filter and use the PPCH prime function to run oil through
the filter and into a catch vessel.
Disconnecting the filter to run a high pressure solvent
through the filter elements may be done but great care must
be taken to ensure that the solvent is completely removed
and no particles or contaminants are introduced to the outlet
(PPCH side) of the filter.
If the filter becomes clogged in use then a pressure
difference between the PPCH or PPCH/PG and the DUT
may result during pressure ramps, including vent. This
could prevent proper operation and cause significant
measurement error.
Figure 1: High Pressure Filter
Figure 2: Installation of filter on stand alone PPCH.
Figure 3: Installation of filter on PPCH with a PG7302.
HIGH PRESSURE FILTER KIT
P/N 402376
INSTRUCTION SHEET
  • Page 1 1

Fluke Calibration PPCH Instruction Sheet

Type
Instruction Sheet

Fluke Calibration PPCH is a high-performance hydraulic pressure controller designed to provide accurate and stable pressure control for a wide range of applications. With its ability to generate and control pressures up to 10,000 psi (690 bar), the PPCH is ideal for testing and calibrating pressure transducers, gauges, and other pressure-related devices.

The PPCH features a precision pressure regulator that provides excellent pressure stability and accuracy. The controller also includes a built-in pressure gauge that allows users to monitor the pressure output. Additionally, the PPCH has a variety of input and output connections that make it easy to connect to different types of pressure devices.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI