Auscrown CS900 Installation & Operation Manual

Brand: Auscrown

Model: CS900

Type: Installation & Operation Manual

Stainless Steel Canopy Rangehood

INSTALLATION & OPERATION MANUAL

Thank you for choosing an Auscrown Rangehood.

PLEASE READ CAREFULLY AND UNDERSTAND THIS MANUAL BEFORE INSTALLING

AND OPERATING THE CANOPY RANGEHOOD

C600G

CS900

IMPORTANT: THIS APPLIANCE MUST BE INSTALLED AND SERVICED BY A LICENSED ELECTRICIAN

IMPORTANT: PLEASE READ FULLY PRIOR TO INSTALLATION OR OPERATION

 This canopy rangehood is an indoor appliance and has been manufactured and tested to comply with

Australian Standard/New Zealand AS/NZS60335.2.31:2004 inc amendment 1 & 2 with Electrical Approval

Number ITACS A/10752EA.

 This canopy rangehood is for domestic use only and not for commercial use.

 Always switch power off prior to installing, servicing or cleaning the appliance.

 Never use the appliance without filters.

 Please read the notes on maintenance / cleaning, especially the filters.

 Exhaust air must not be discharged into a heating flue or wall cavity, unless the cavity is designed for that

purpose.

 If the rangehood is to be installed in an area that also has gas, oil or coal fired heaters, the area must be

well ventilated to prevent a partial vacuum in the room. This includes gas hobs. (A partial vacuum in the

room could result in too high a concentration of gas in the atmosphere and excessive consumption of

oxygen).

 The appliance is supplied with an approved power cable which must not be changed. If the supply cord of

this equipment is damaged, it must only be replaced by the manufacturer, its service agent or similarly

qualified person in order to avoid hazard.

 Care and attention should always be taken when cooking with oils, alcohol, etc; which give off flammable

vapours. Pre-used oil is especially dangerous in this respect. Do not use any uncovered electrical grill with

this rangehood.

 To avoid possible risks of fire always comply with the maintenance instruction below.

ATTENTION: THIS APPLIANCE MUST BE EARTHED

When making the electrical connection, check that the socket has an earth connection and that the voltage

values correspond to those indicated on the rating plate inside the appliance. The power socket connection is

to be easily accessible after installation.

WARNING: FOR YOUR SAFETY

 This appliance is not intended for use by young children or infirm persons without supervision.

 Children should be supervised to ensure that they do not play with the appliance.

 There should be adequate ventilation of the room when the rangehood is used at the same time with

appliances burning gas or other fuels.

 You must read the details concerning the method and frequency of cleaning.

 There is a fire risk if cleaning is not carried out in accordance with the instructions.

 Do not flambé (pour alcohol over food and set fire to it during cooking) under the rangehood.

 Exhaust air must not be discharged into an existing flue which is used for exhausting fumes from

appliances burning gas or other fuels.

 Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air

is fulfilled.

INSTALLATION

Notes

 Prior to installation. Please ensure that any existing or proposed roof ducting installation for connection to

this appliance is suitable and complies with local municipal building codes and other statutory/ building

regulations. If you are unsure, please check with appropriate authorities or a qualified roof ducting installer.

 This appliance must be installed in accordance with any local municipal building codes and other statutory

regulations.

 Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air

is fulfilled.

 Ensure that the fully installed canopy has the clearance of 650 mm to 700mm between the lowest part of

the hood and the cooking hob.

 Before drilling any holes check the wall and ceiling are clear of any electrical cables, pipes etc.

 For wall-mount type rangehood, the unit is supplied with a mounting bracket that must be fixed onto the

wall first. If the wall where the rangehood is to be mounted on is a cavity wall then a solid noggin or stud

(horizontal or vertical timber/metal house framing behind the wall) is required for the mounting bracket to

screw into. Due to the heavy weight of the rangehood, it must not be mounted onto the plasterboard wall

without solid support from behind the wall surface.

 For dimensions, see “Product Dimensions” diagrams below.

Product Dimensions

CS900

C600G

Parts Name

CS900

C600G

Installation Procedure

FOR C600G and CS900

1. Put the canopy on the wall over the cooker, and mark the height position where the distance from the

bottom of the canopy to the top edge of the cooker is at least 650mm. (See Figure 1)

Figure 1

Figure 2 (C600G)

2. Mark the hole positions on the wall and install wallmates and screws. (See Figure 2 & 3)

3. Hang the canopy on the wall and tighten the screws.

For CS600 model — Tighten the lower screws to secure the canopy. If the canopy seems acclivitous, use

the adjustable screws to adjust it to level. (See Figure 4)

Figure 3 (CS600)

Figure 4

4. Insert the exhaust pipe onto the outlet of the canopy. (See Figure 5)

5. Install the duct brackets onto the inner duct cover. (See Figure 6)

Figure 5

Figure 6

6. Slide the inner duct cover into the outer duct cover. (See Figure 7)

7. Install the duct covers onto the canopy. (See Figure 8)

Figure 7

Figure 8

8. Draw up the inner duct cover up to the preferred height, and mark down position of screw holes of the duct

bracket onto the wall, then push it down. Drill hole through the marks and insert a expanding tube.

9. Elongate the exhaust pipe and connect to the inlet of the exhaust flue. (See Figure 9)

10. Lift up the duct cover and match the duct bracket keyholes with the expanding tube, and secure with 2

screws. Then pull down the outer duct cover and fit it back onto the canopy. (See Figure 10)

Figure 9

11. Fix the outer duct cover with 2 pieces of M4x10

screw.

12. Plug the power cord into the power point.

Figure 10

OPERATION

HOW TO USE THE CONTROL

CS900

C600G

Button A: On/off switch for Lights

Button B: High fan speed.

Button C: Medium fan speed.

Button D: Low fan speed.

Button E: On/Off switch for fan.

Button A: On/Off switch for Lights.

Button B: High fan speed.

Button C: Medium fan speed

Button D: Low fan speed

Button E: On/Off switch for fan

MAINTENANCE / CLEANING

 Particular care must be taken with any sharp edges on the rangehood.

 When cleaning stainless surfaces, use a damp cloth and mild detergent. Never use products containing

abrasives (e.g. scouring pads, steel wool, abrasive liquid cleaner etc.)

 In high humidity and coastal environments, cleaning should be carried out frequently.

 Ensure the canopy rangehood is switched off before cleaning.

 Wipe the rangehood body and flue with mild detergent or soapy water using a sponge or soft cloth. Do not

use oven cleaners, caustic solutions or abrasive materials.

 Ensure the fan and light switches are switched off before removing and replacing filters. To maintain

efficiency and reduce fire risk, the filters should be cleaned monthly. Press the clamp of the filter lightly and

take off the filter. Wash the filter in warm soapy water using a mild detergent and a soft brush. Or place in

top rack of dishwasher. Do not use oven cleaners, caustic solutions or corrosive agents.

 Ensure the fan and light switches are set to ‘Off’ before removing and replacing the light globe.

TO REPLACE A LIGHT BULB

 It is recommended replacing light bulb to be carried out by a licensed electrician.

 CAUTION! Lamp unit may be hot! Wait until the unit is cool and use the same type of light bulb.

 Make sure all switch controls are off and the rangehood is unplugged.

1) Make sure the bulb is cool to touch

2) Use a flathead screwdriver to take out the lamp assembly, then disconnect lamp from the internal wires

3) Loosen the screws and remove the lamp cover to take out the lamp bulb

4) Replace with a new lamp bulb (check specification for which type), put bulb securely into lamp socket.

5) Put the lamp bulb back into the lamp cover and fix with screws

6) Connect the lamp assembly with internal electrical wire and push the light into the hood lamp hole

TROUBLESHOOTING - CAUTION: DISCONNECT THE POWER SUPPLY BEFORE SERVICING

Problem Cause and Method of Repairing

The power supply is

damaged

Please call Austcrown or a licensed electrician for repairs. Do not attempt to repair yourself

The lamps are working

but the motor does not

run

1) The fan or the motor may be blocked, check they are in the correct position

2) The motor is damaged – replace with a new one

3) The switch control is damaged – replace with a new one

4) The capacitance is damaged – replace with a new one

The canopy body shakes

1) Check the rangehood has been installed securely and correctly.

2) The fan is broken so there is imbalance – replace with a new one

3) The blower is not installed correctly, check it is in the correct position

4) The motor is not installed securely, check it is securely installed

Loud Noise

1) The blower is not in balance, adjust the screws to re-balance it or replace with new one

2) Something has come loose and dropped onto the blower. Check for any loose items and

remove it

Light does not work Replace with a new light bulb or light assembly

SPECIFICATIONS

MODEL CS600 C600GH

Mount Wall Wall

Finish Stainless Steel Stainless Steel & Tempered Glass

Width 900mm 600mm

Motor 250W 170W

Speed Level 3 Speed 3 Speed

Light 2 x 2W LED 2 x 10W Halogen

Air Outlet

150mm 150mm

Max Air Capacity 1000m

/hr 660m

/hr

Max Noise Level 70 dB 70 dB

Voltage 220V-240V (60Hz) 220V-240V (60Hz)

Exhaust Pipe 2m 2m

Gross Weight 23.5kg 16kg

Austcrown Pty Ltd will not be liable in respect of any misuse of this appliance not in accordance with the instructions and

precautions specified in this booklet.

FOR SERVICES AND ENQUIRY, PLEASE CONTACT:

Austcrown Pty Ltd

18 / 634 Mitcham Road, VERMONT VIC 3133, AUSTRALIA

Ph: (03) 9873 5811 Fax: (03) 9873 5311 Email: [email protected]

Website: www.auscrown.com

Auscrown CS900 Installation & Operation Manual

Brand: Auscrown

Model: CS900

Type: Installation & Operation Manual

Download PDF

report

Auscrown CS900 Installation & Operation Manual

Auscrown CS900 Installation & Operation Manual

Other documents