Powerplus POWLI20201 Owner's manual

Type
Owner's manual

Powerplus POWLI20201 is a powerful LED floodlight with a motion sensor, perfect for illuminating outdoor areas like gardens, job sites, and workshops. With a sturdy tempered glass facade and IP65 waterproof rating, it can withstand harsh weather conditions. Customize settings like duration (3 seconds to 5 minutes), sensitivity (1m to 6m), and light level activation (10lux to 1000lux) for optimal performance. Enjoy bright, energy-efficient lighting with a 1500 lumen output, 6500K cool white color temperature, and a wide 100° beam angle.

Powerplus POWLI20201 is a powerful LED floodlight with a motion sensor, perfect for illuminating outdoor areas like gardens, job sites, and workshops. With a sturdy tempered glass facade and IP65 waterproof rating, it can withstand harsh weather conditions. Customize settings like duration (3 seconds to 5 minutes), sensitivity (1m to 6m), and light level activation (10lux to 1000lux) for optimal performance. Enjoy bright, energy-efficient lighting with a 1500 lumen output, 6500K cool white color temperature, and a wide 100° beam angle.

POWLI20201 EN
Copyright © 2018 VARO P a g e | 1 www.varo.com
LED FLOODLIGHT 20W WITH SENSOR
POWLI20201
1 DOMAIN OF USE
Outdoor or indoor usage such as jobsite, garden, studio and workshop.
WARNING! Read this manual and general safety instructions
carefully before using the appliance, for your own safety. Your power
tool should only be passed on together with these instructions.
2 WARNING
This Product is Class I and must be Earthed.
Always switch off mains supply before fitting.
Replace any broken or damaged glass as soon as possible.
Ensure all seals are intact and operational after fitting or maintenance.
Do not touch the lamp in use or just after use as there is a risk of being burnt.
Do not cover it with paper or cloth.
Take off from flammable materials.
Do not wash the lamp.
Do not use the lamp where the ambient temperature is over 45°C and less than -
25°C.
Keep with a secure distance, the light could cause damage to your eyes.
To move or placed, the product must face up to avoid damage to the sensor.
3 ASSEMBLY
Find a suitable location to install this product.
Prepare the mains wiring.
Use the mounting bracket to mark the hole centres for fixing.
Drill holes suitable to accept wall plugs. Insert wall plugs.
Ensure mounting bracket.
Terminate wiring. (Fig. 1)
Replace all covers.
Fit the floodlight to the mounting bracket with the screws,
Check seals, gaskets and cable gland operation before testing the luminaire.
Turn on power supply and test luminaire.
4 SETTING THE LIGHT SYSTEM
4.1 TIME adjustment
The TIME adjustment controls how long the floodlight will
stay on after the motion has been detected.
You can adjust time from 3 seconds to 5 minutes.
4.2 LUX adjustment
POWLI20201 EN
Copyright © 2018 VARO P a g e | 2 www.varo.com
The LUX adjustment determines at what light level the
lighting system will start operating.
You can adjust LUX from 10lux to 1000lux.
4.3 SENS. adjustment
The sensitivity adjustment may be adjusted to compensate
for seasonal variations in temperature and to reduce
unwanted triggering. Detecting distance can be adjusted
from 1m to 6m.
5 TECHNICAL DATA
Type
Power
Voltage/frequency
Floodlight facade material
Waterproof protection grade
life-span
Lumen
Color temperature
Beam angle
Detection angle
Net weight
Dimensions
6 POSSIBLE PROBLEMS
Ventilators, such as the discharge from a vapor cap or dryer (hot air movement) can
cause the lamp to switch on when it is not required to do so.
Passing cars (warm engines) can also cause your lamp to switch on.
Nearby trees and bushes, sudden changes in temperature and gusts of wind can
also cause the lamp to switch on.
If the lamp has been placed under a roof or under trees, then the lamp can also burn
during daylight hours.
If your lamp does not work then the bulb or fuse could be defective or there may have
been a failure in the electrical circuit.
If the temperature difference between the object to be detected and surrounding area
is too small (in the summer for example), then your lamp will react later. The range of
detection is then 5 meters instead of 7 meters for example.
POWLI20201 EN
Copyright © 2018 VARO P a g e | 3 www.varo.com
If the electromagnetic interferences are strong enough (4KV electrostatic discharge,
3V/m electromagnetic HF-field and 500V electrical fast transient burst), then the lamp
may turn on unintentionally.
7 MAINTENANCE
This product has no user serviceable parts.
Clean with a damp cloth and dry with a lint free cloth or kitchen towel.
8 IMPORTANT INFORMATION
It is recommend that luminaires installed and fitted by a qualified electrician ensuring the
installation complies to the current building regulations. These products are designed for
connection to a 220-240V supply.
Any broken or damaged parts should be replaced as soon as possible.
9 ENVIRONMENT
Should your appliance need replacement after extended use, do not
discard it with the household rubbish but dispose of it in an environmentally
safe way.
Waste produced by electrical machine items should not be handled like
normal household rubbish. Please recycle where recycle facilities exist.
Check with your Local Authority or retailer for recycling advice.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Powerplus POWLI20201 Owner's manual

Type
Owner's manual

Powerplus POWLI20201 is a powerful LED floodlight with a motion sensor, perfect for illuminating outdoor areas like gardens, job sites, and workshops. With a sturdy tempered glass facade and IP65 waterproof rating, it can withstand harsh weather conditions. Customize settings like duration (3 seconds to 5 minutes), sensitivity (1m to 6m), and light level activation (10lux to 1000lux) for optimal performance. Enjoy bright, energy-efficient lighting with a 1500 lumen output, 6500K cool white color temperature, and a wide 100° beam angle.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI