Eaton 68504 Datasheet

Brand: Eaton

Model: 68504

Category: Uninterruptible power supplies (UPSs)

Type: Datasheet

This manual is also suitable for

Entreprise Networks

Telecom

Process and infrastructures

Redundancy for highly critical applications.

www.mgeups.com

Can be built in to high density racks.

Single phase UPS

Pulsar MX

4/5/8/10/15/20 kVA

Continuous power supply

◗ Two front access hot-swappables

sub-modules (power and battery)

for maintenance without load

interruption.

◗ Automatic battery test (test period

can be set).

◗ Internal bypass built-in to supply the

load even if the UPS fails.

◗ Large input voltage and frequency

ranges to avoid using the batteries

unnecessarily.

Flexible

◗ Can be used as a free-standing tower

unit or 19" rack-mounted: only 3U

for Pulsar MX 4000 and 5000,

16U for Pulsar MX Frame

◗ LCD multilingual display with mimic

and LEDs for rapid view of the UPS

status, diagnostics and event log

◗ Outputs: IEC 10A and 16A outlet

sockets and hardwired outputs

◗ Built-in Powershare system for remote

reboot of the equipment connected,

sequential start-up or load shedding

while operating from battery to

maintain the power to critical loads.

◗ Pulsar MX Frame is compatible with

three phase or single phase supplies.

◗ Backup time: 10 mins up to 2 hours

by adding 3U battery extension

modules.

Minimum total cost

of ownership (TCO)

◗ More power with an output

power factor of 0.9.

◗ When the power supply needs

to be upgraded, the Pulsar MX

4000 and 5000 can be paralleled

to provide 8 kVA or 10 kVA

using the ModularEasy kit:

without extra cost on the

initial purchase.

◗ Pulsar MX Frame is a modular

system with 5 kVA sub-modules

paralleled to provide up to 20 kVA

or 15 kVA with redundancy.

High performance UPS upgradeable

from 4 kVA to 20 kVA

Can be used for 20 to 110

servers, ideal for:

◗ departmental networks, servers

and workstations

Pulsar MX: 10 minutes

backup, tower/rack

mounting (3U), mimic,

LCD display.

Pulsar MX has 2 sub-modules

(power electronics and battery)

which are hot swappable.

Pulsar MX Frame 15

and 20 kVA tower

and rack-mounting (16U),

modular system with

5 kVA sub-modules.

Paralleling 2 Pulsar MXs

using ModularEasy for 2N

or N+1 redundancy.

The power level can be upgraded simply and without

interruption for the existing loads as the number

of loads supplied is increased.

PULMX515UK.qxd 16/02/06 15:13 Page 1

Single phase UPS - Pulsar MX

Headquarters

140, avenue Jean-Kuntzmann

ZIRST - Montbonnot Saint-Martin

38334 Saint-Ismier Cedex - France

Tel.: +33 (0)4 76 18 30 00

PULMX515UK-02/06

Due to developments in technical standards and the equipment described in this document, we cannot be held liable for compliance with the characteristics indicated by the images and text unless they are confirmed by us. All the brand names referred to in this document are protected by copyright.

Publication: MGE UPS SYSTEMS (February 2006) - Design and rewriting: 3c-evolution.com - Integration: Pamplemousse: +33 4 79 37 87 66 – Translation: TTP: +33 4 78 66 47 99.

Specifications

Pulsar MX 4000 RT Pulsar MX 5000 RT Pulsar MX 15000 Frame 16U Pulsar MX 20000 Frame 16U

Pulsar MX RT Tower or rack-mounting: standard backup time

68 501 68 504 68 513

(14)

68 514

(15)

Pulsar MX RT Netpack: standard backup time

68 502 68 505

(with rack kit, (with rack kit,

+ NMC + rack kit casters, NMC card) casters, NMC card)

Pulsar MX EXB RT : battery extension module 68 515 68 527

(Pulsar MX Frame EXB empty to be fitted with 4 or 8 Battery sub-modules)

Pulsar MX ModularEasy: paralleling kit (2 Pulsar MX)

68 520 -

MX / EXB RT Rack Kit: rail kit for 19" rack mounting

68 002 -

IEC 32 A kit , 2 X 2 m long cables: male to

68 525 -

hardwired and female to hardwired

Pulsar MX Battery / Power electronics sub-module

68 524 / 68 522 68 524 / 68 523 68 524 / 68 523

Part numbers

1: Available from November 2006. 2: 2 Pulsar MXs can be paralleled using ModularEasy. 3: At 70% load. 4: 4 IEC C13 (10A) 2 m long cables for use with retention clips (8 cables for use with Pulsar MX Frame).

5: Frequency conversion for non-paralleled units only. 6: Economy mode, 91% in normal mode. 7: At 70% nominal rating with power factor 0.7 typical values after 3 charge/discharge cycles, with 3-5 year old

batteries. Weekly battery test without interrupting the load (daily or monthly if required). EXB compatible with 0.8 power factor loads. 8: With Pulsar MX Frame EXB (4 battery units). 9: With Pulsar MX Frame EXB

(8 battery units). 10: Solution-Pac CD-ROM supplied as standard. 11: Applicable to US models. 12: 50 dbA above 5 kVA. 13: Depending on the country, see www.mgeups.com/service. 14: 68 513 = 68 526

(empty Pulsar MX Frame) + 3 x 68 524 + 3 x 68 523. 15: 68 514 = 68 526 (empty Pulsar MX Frame) + 4 x 68 524 + 4 x 68 523.

Pulsar MX RT 4 kVA 5 kVA 15 kVA

(1)

20 kVA

(1)

Rating (kVA) / (kW) 4 kVA / 3,6 kW 5 kVA / 4,5 kW 15 kVA / 13, 5 kW 20 kVA / 18 kW

Paralleling

Maximum rating /

8 kVA / 4 kVA + 4 kVA redundancy 10 kVA / 5 kVA + 5 kVA redundancy 15 kVA / 10 kVA + 5 kVA redundancy 20 kVA / 15 kVA + 5 kVA redundancy

redundancy

(2)

5 kVA + 2 x 5 kVA redundancy 10 kVA + 2 x 5 kVA redundancy

Inputs

Technology VFI-SS-113, on-line double conversion with power factor correction, convection cooled static bypass switch

Number of phases, input connections L + N, terminals up to 6 mm

L + N or 3P + N, terminals up to 35 mm

separate or common AC normal and AC bypass

Nominal voltage 200/208/220/230/240/250 V 200/208/220/230/240/250 V (L + N) or 380/400/415 V (3P + N)

Voltage range without using battery

(3)

120 - 280 V 120 - 280 V (L + N), 250 - 465 V (3P + N)

Input frequency range, THDI 40-70 Hz, < 7%

Outputs

Output connections

(4)

terminals + 8 IEC C13 (10A) + 2 IEC C19 (16A) terminals + 16 IEC C13 (10A) + 4 IEC C19 (16A)

Remotely controlled Powershare sockets 2 groups (2 IEC C13 10A per group) 2 groups (4 IEC C13 10A per group)

Output voltage and frequency

(5)

, THDU, efficiency

(6)

200/208/230/240 /250 V, 50 / 60 Hz autoselect, frequency converter as standard, <2%, 97%

Backup time

(7)

Pulsar MX standard backup time 10 minutes 8 minutes 8 minutes

Pulsar MX + EXB / MX + 2 EXB / MX + 3 EXB 45 / 80 / 120 minutes 35 / 60 / 95 minutes 20 minutes

(8)

/ 35 minutes

(9)

Communications

Slots 1 minislot or 2 minislots (Frame) compatible with Minislot NMC, NMC ModBus/JBus, MC Contacts/Serial

Ports Remote Power off (RJ11), 5 output contacts (DB9), setup using Solution-Pac

(10)

(USB and DB9-serial ports),

EXB module detection (RJ45), paralleling (DB 15)

Operating conditions, standards and approvals

Performance, safety, EMC, surge protection IEC/EN 62 040-3, IEC/EN 62 040-1-1, IEC/EN 62 040-2 class A (class B as option), 4 kV IEC 61 643, UL 1778 and CSA 22.2

(11)

Operating temperature, noise, approvals, guarantee

0°C to 40°C continuous, 45 dbA

(12)

, UL, TüV, GS mark, CB, C-Tick, CE, IEC 61 931, one year

(13)

Dimensions / weight

Pulsar MX RT standard backup tower 444.5 mm high x 130.6 mm wide x 735 mm deep / 57 kg

To wer 690 mm high (795 mm casters) x 444.5 mm wide x 735 mm deep /

Pulsar MX RT standard backup rack

3U x 444.5 mm wide compatible with 800-1000 mm deep rack

250 kg Rack 16U x 444.5 mm wide, compatible with 800-1000 mm deep rack