Minka Group 392-613-L User manual

Brand: Minka Group

Model: 392-613-L

Type: User manual

Minka Group 392-613-L is a dimmable wall mount fixture that can be used to replace an old fixture. It is designed to be installed by a qualified electrician and requires shutting off power at the fuse box or circuit breaker box before starting the installation. The fixture has a ground wire that must be connected to the home's electrical system for safety. It also comes with mounting screws and wire connectors for easy installation. The fixture can accommodate glass shades and uses LED modules for illumination.

IMPORTANT:

Fixture should be installed by a qualified

electrician to ensure proper wiring and installation.

Dimmable with ELV and/or LED compatible wall

dimmer switches.

INSTALLATION INSTRUCTIONS

FOR

613

For Wall Mount Fixture

W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .

A V E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O D I S J O N C T E U R

PREPARATION

1. Shut off power at the fuse box or circuit breaker box. If

necessary remove the old fixture and mounting hardware.

Carefully unpack your new fixture and lay out all the parts

on a clear area. Take care not to lose any small parts

necessary for installation

MOUNTING THE FIXTURE (FIG. 1)

Secure mounting back plate (C) to junction box (A) using

junction boxes screws (D) (Size: 8-32*1/2”L). The side of the

mounting back plate marked “GND” must face out.

CONNECTING THE WIRES (FIG. 2)

3. At this point, connect the electrical wires as shown in Fig. 2,

making sure that all wire connectors(B) are secured. If your

outlet has a ground wire (green or bare copper), connect

the fixtures ground wire to it. Otherwise, connect the fixture

ground wire directly to the mounting plate (C) using the

green screw provided. After wires are connected, tuck

them carefully inside the junction box.

4. Align the fixture’s back plate (E) over the mounting back

plate (C) and secure with screws (B).

FINISHING THE INSTALLATION (FIG.1).

5. Carefully slide glass shades G392/393 (I) into the bracket

(F) and secure the glass holders (G) to the bracket (F) with

screws (H).

CAUTION /ATTENTION:

When handling the fixture, do not

apply pressure to the LEDs. Hold the fixture by the back plate

(E) or bracket (F).

Replacing LED module (Fig. 3)

The LED module can be replaced by a qualified electrician

without cutting of wire and without damage to any decorative

element to which the fixture is attached. See installation steps

for more details (Fig 3.)

a. Shut off power. Remove screws (H) glass holders (G)

and glass shades G392/393 (I).

b. Remove the wire nuts located inside the fixture back plate

to disconnect the LED module.

c. Remove cover (J) on LED module (L) and screws (K) on

bracket (F). Carefully remove the LED module (L) from

bracket (F).

d. Reverse steps a-c for installing the new LED module.

e. Note: The LED module should be provided by a specified

supplier.

f. For better heat dissipation the LED module (L) should be

applied with thermal grease when re-lamping.

FIG.1

Back plate

Green screw

Mounting Screws(2)

Fig 3

Fig.2

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

HOUSE

WIRES

Green or

Bare

Copper(G

round)

Minka Group 392-613-L User manual

Minka Group 392-613-L User manual

Minka Group 392-613-L User manual

Related papers

Other documents