Commax IDentry-T45-T Owner's manual

Brand: Commax

Model: IDentry-T45-T

Category: Serial converters/repeaters/isolators

Type: Owner's manual

This manual is also suitable for

IDentry-T45-K

Installation Manual

T45

www.commax.com

Thank you for purchasing COMMAX products.

Please carefully read this User’s Guide (in particular, precautions for safety) before using a product and

follow instructions to use a product exactly.

The company is not responsible for any safety accidents caused by abnormal operation of the product.

Back of T45

LAN CON12 CON2

CON1 CON4 CON13

CON12) Relay 1, 2

- Connects with door lock and alarm devices

CON4) Card Reader

- Connects with external card reader

CON2) Sensor Input

- Connects with various sensors (door contact, alarm sensor etc)

and exit button

CON13) Wiegand output

- Outputs CARD data

(Used when it is integrated with other main controller)

CON1) Power Input / RS 485

- Supply 12V power to T-45 through power supply

- Communicate RS-485 with PC

LAN_CON9) TCP/IP Connector

- Communicate TCP/IP with PC

LAN CON12 CON2

CON1 CON4 CON13

T45 CONNECTIONS

RS-485

Converter

RS-232

#16

DIAGRAM (RS-485)

It is possible to connect numerous

T45 with computer.

Maximum number of connection with

one serial port is 16 T45.

Must give unique address to each

T45 (Refer to user manual for the setup)

If not, arouses communication collision and

cannot communicate.

RS-485

Converter

RS-232

#33

#34

#35

#48

RS-485

Converter

#49

#50

#51

#64

RS-485

#17

#30

#31

#32

#14

#15

RS-485

RS-232

RS-485

Converter

RS-485

Converter

RS-485

RS-232

#16

Multi

Port

RS-232

T45(Units) 포트 (No)

Maximum number of connection

with one serial port is 16units.

If main computer controls above

6units of T45, needs to prepare

additional port. CAMS S supports

up to 4 RS-485 converters.

NETWORK DIAGRAM (RS-485)

TCP/IP

HUB

DIAGRAM (LAN)

Shows LAN composition connecting numerous T45

Must give unique IP address to each T45 (Refer to user manual for the setup)

TCP/IP

HUB

TCP/IP

WAN

DIAGRAM (WAN)

Shows the connection with

64units of T45.

(Needs 64 IP address)

LAN CON12 CON2

CON1 CON4 CON13

DC 12V

GNC

VCC

Transformer

AC220V

60Hz

DC_IN

CON1

GNC VCC

(Red) (Black)

CN700(DC-In) connects with DC12V and GND.

Doesn’t matter the direction of the GND and VCC.

CABLE CONNECTION (POWER)

CON1

DC_IN

from : PC

RS-232RS-485

MAX : 1200m (4000ft)

+12V

GND

RX-

RX+

TX=/A=

TX+/A+

ex) RS232-485 CONVERTER

LAN CON12 CON2

CON1 CON4 CON13

Shows the connection CN700(DC-IN) and RS-232/485 Converter

CABLE CONNECTION (RS-485)

LAN CON12 CON2

CON1 CON4 CON13

HUB

TCP/IP

CABLE CONNECTION (TCP/IP)

Shows TCP/IP connects with T45 using the HUB.

No distance limits using TCP/IP and configure access control system with LAN or WAN

(Refer to user manual or CAMS S software manual for the IP setup)

LAN CON12 CON2

CON1 CON4 CON13

12V

GND

WIG 0

WIG 1

GND

CON13

LMP

RNT

DATA0

DATA1

PWR

RDE-A

RELAY1

RELAY2

ACU

(ex: PCSC IQ-Serise)

Shows LAN composition connecting numerous T45

Must give unique IP address to each T45 (Refer to user manual for the setup)

CABLE CONNECTION (WIEGAND OUT)

If connected to other main controller, it works as a card reader or fingerprint reader only not controller.

CN506(Wiegand out) connects with card reader port of main controller and transmit the data via Wiegand

CON4

Reader

(ex : KP-10)

Red:12V

Black : GND

Green : Date 0

White : Date 1

Blue : LED Control

LAN CON12 CON2

CON1 CON4 CON13

CABLE CONNECTION (RF CARD READER)

Connects the cable of the RF card reader to CN503.

Connection would be variable for each reader. (Follow the manual of each RF card reader)

CON2

Sliding Door

EXIT BUTTON

Invasion Sensor

(or Fire Alram)

Door Contact

Embedded

AutoDoor Sensor

Exit

GND

Door Contact

GND

Invasion(Fire)

Timed Input

+5V

LAN CON12 CON2

CON1 CON4 CON13

CABLE CONNECTION (SENSOR)

Shows T45 connected with sliding door and relevant controls ; door contact, door sensor, exit button, infrared sensor.

LAN CON12 CON2

CON1 CON4 CON13

RELAY-1

RELAY-2

CON12

N.O.

N.C.

COM

N.C.

N.O.

Alram

Alert

Device

GND

Transfomer

Electric Magnetic

Lock

DC12V

CABLE CONNECTION (RELAY)

Shows physical access controls of T45 by connecting many devices which detect certain situation through the sensors explained in the above.

Electric strike or alarm devices to be operated with T45 using the connection of CN501.

Commax IDentry-T45-T Owner's manual

Brand: Commax

Model: IDentry-T45-T

Category: Serial converters/repeaters/isolators

Type: Owner's manual

This manual is also suitable for

IDentry-T45-K

Download PDF

report

Commax IDentry-T45-T Owner's manual

This manual is also suitable for

Commax IDentry-T45-T Owner's manual

Related papers

Other documents