Acnodes PM6084 is an 8.4” TFT LCD monitor with a resolution of 800 x 600 pixels. It has a contrast ratio of 600:1 and a brightness of 250 cd/m2. The monitor has a viewing angle of 80 degrees in all directions. It is equipped with a VGA input and can be powered by an AC adapter or a 12VDC power supply. The monitor can be mounted on a wall, panel, or VESA mount. It is suitable for use in industrial, commercial, and home applications.
Acnodes PM6084 is an 8.4” TFT LCD monitor with a resolution of 800 x 600 pixels. It has a contrast ratio of 600:1 and a brightness of 250 cd/m2. The monitor has a viewing angle of 80 degrees in all directions. It is equipped with a VGA input and can be powered by an AC adapter or a 12VDC power supply. The monitor can be mounted on a wall, panel, or VESA mount. It is suitable for use in industrial, commercial, and home applications.
Industrial
Monitors
User Manual
All rights reserved. Product description and product specifications are subject to change without notice.
For lastest product information, please visit Acnodes’ website at www.acnodes.com
14628 Central Ave. Chino, CA 91710 Tel: 909.597. 7588 Fax: 909. 597.1939
© C opyright 2015 Acnodes C orp.
PM6084
8.4 ” 8 0 0 x 600 TFT LCD
Op e n F ra m e LCD M o n i to r
Wal l / P a ne l / VESA M o u n t Re a d y
L eg al Inf orm ation
F irst Eng Iish printing, O ctober 2002
Information in this doc ument has been carefu IIy checked for accuracy; however, no guarantee is given to the correctness
of the contents. T he information in this docum ent is subject to change without notice. W e are not Iiab Ie for any injury or
Ioss that resu Its from the use of this equipm ent.
Safet y Inst ru cti ons
Please read all of th ese in structio ns carefully before yo u use th e d e vice. Save this m anual for futu re reference.
● Unp Iug equipm ent before cIeaning. Don’t use Iiquid or spray detergent; use a moist cIoth.
● Keep equipm ent aw ay from excessive humidity and heat. PreferabIy, keep it in an air-conditioned envir onment with
temperatures not exceeding 40 º Ce Isius (104 º F ahrenheit).
● When insta IIing, pIace the equipment on a sturdy, Ieve I surface to prevent it from accidenta IIy fa IIing and causing dam
age to other equipment or injur y to persons nearby.
● When the equipment is in an open position, do not cover, b Iock or in any way obstruct the gap betw een it and the
pow er suppIy. Proper air convection is necessary to k eep it from overheating.
● Arrange the equipm ent’s power cord in such a way that others w on’t trip or fa II over it .
● If you are using a pow er cord that didn’t ship with the equipment, ensure that it is rated for the vo Itage and cur rent
Iabe Ied on the equipment’s eIectric aI ratings IabeI. T he vo Itage rating on the cord shou Id be higher than the one Iisted
on the equipment’s ratings Iabe I.
● Observ e a II precautions and warnings attached to the equipment.
● If you don’t intend on using the equipment for a Iong time, disconnect it from the power outIet to prevent being dam
aged by tr ansient over-voItage.
● Keep a II Iiquids aw ay fr om the equipment to minimize the risk of accidenta I spiIIage. Liquid spiIIed on to the pow er
suppIy or on other hardware may cause damage, fire or e Iectrica I shock.
● On Iy qua Iif ied service personne I shou Id open the chassis. O pening it yourseIf cou Id damage the equipm ent and inva Ii
date its w arranty.
● If any part of the equipment becomes damaged or stops functioning, have it c hecked by quaIified service personne I.
W hat the w arran ty d oes not co ver
● Any product, on which the seriaI number has been defaced, modified or rem oved.
● Damage, deterioration or ma Ifunction resu It ing from:
● Accident, m isuse, neg Iect, f ire, water, Iightning, or other acts of nature, unauthorized product modification, or
faiIure to fo IIow instructions supp Iied with the product.
● Repair or attempted repair by anyone not authorized by us.
● Any damage of the product due to shipment.
● RemovaI or ins taIIation of the product.
● Causes externa I to the product, such as e Iectric power f Iuctuation or faiIure.
● Use of supp Iies or parts not meeting our specifications.
● Norma I wear and tear.
● Any other causes w hich does not re Iate to a product defect.
● RemovaI, insta IIation, and s et-up service charges.
Regulato ry Notices Federal Co mm un ications Com m ission (FCC)
T his equipment has been tested and found to comp Iy with the Iimits for a CIass B digita I device, pursuant to Part 15 of the
F CC ru Ies. These Iimits are designed to provide reasonabIe protection against harmfuI interference in a residentia I insta I-
Iation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipm ent. This
equipment generates, uses, and can radiate radio frequency energy and, if not instaIIed and used in accordance with the
instructions, m ay cause harmfuI interference to radio communications.
How ever, there is no guar antee that interference wiII not occur in a particu Iar instaIIation. I f this equipment does caus e
harmfu I interference to radio or te Ievis ion reception, which c an be deter mined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the fo IIowing m easures:
● Re-pos ition or reIocate the receiving antenna.
● Increase the separation between the equipm ent and receiver.
● Connect the equipment into an outIet on a circuit different from that to which the receiver is connected.
Contents
< Part. 1 > PM 6084
1.1 Package Content
1.2 Structure Diagram & Dimension
1.3 Mounting Hardware & InstaIIation
P.1
P.2 - 3
P.4 - 5
< Part. 2 > Product Specifications & LCD OSD
2.1 Product Specifications
2.2 On-screen DispIay Operation ( OSD )
P. 6 - 7
P. 8
< Part. 3 >
Options
3.1 Option TabIe
3.2 S-Video + BNC & Audio
3.3 8.4" Touchscreen : Resistive, Capacitive
3.4 48V, 24V or 12VDC power
3.5 TV ( AnaIog )
P. 9
P.10
P.11
P.12
P.13 - 14
Before Installation
● It is very important to mount the equipment in a suitabIe cabinet or on a stabIe surface.
● Make sure the pIace has a good ventiIation, is out of direct sunIight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are
incIuded and in good condition. If anything is missing, or damaged, contact the suppIier immediateIy.
How To Clean Your LCD Monitor
Caution :
● To avoid the r isk of eIectric shock, make sure your hands are dry before unpIugging your monitor from or
pIugging your monitor into an eIectricaI outIet.
● When you cIean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your dispIay. Pressure damage is not covered under warranty.
● Use onIy cIeansers made specificaIIy for cIeaning monitors and monitor screens. CIeansers not made to
cIean monitors and monitor screens can scratch the LCD dispIay or strip off the finish.
● Do not spray any kind of Iiquid directIy onto the screen or case of your monitor. Spraying Iiquids directIy
onto the screen or case can cause damage which is not covered under warranty.
● Do not use paper toweIs or abrasive pads to cIean your monitor. Using an abrasive pad or any wood based
paper product such as paper toweIs can scratch your LCD screen.
Cleaning Your Monitor
To cIean your LCD safeIy, pIease foIIow these steps :
1
Disconnect the power cord.
2
GentIy wipe the surface using a cIean, dry microfiber cIoth. Use as IittIe pressure as possibIe.
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, pIease foIIow these steps :
1
Disconnect the power cord.
2
Spray a smaII amount of non-abrasive cIeanser on a microfiber cIoth.
Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your
microfiber cloth first, not directly on the parts you are cleaning.
3
GentIy wipe the surface. Use as IittIe pressure as possibIe.
4
Wait untiI your monitor is compIeteIy dry before pIugging it in and powering it up.
< Part 1 >
< 1.1 > Package Content - PM 6084
PM 6084
8.4" LCD display X 1
6ft VGA cable X 1
Power adapter X 1
Power cord X 1
Standard IIO
Power
VGA
AD1.2 upgrade IIO
Power S-Video BNC VGA
Audio
in - in - out
PC Video
- Options : S-Video + BNC, Audio
1
2
< 1.2 > Structure Diagram-PM6084
Front view
3
Rear view
1 Rear case
2 LCD paneI
4
3 Audio speaker ( for Audio or TV option )
5
4 UniversaI open frame mounting
5 LCD membrane
Model
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
PM 6084
262 x 57 x 189 mm
10.3 x 2.2 x 7.4 inch
515 x 117 x 429 mm
13.5 x 2.5 x 10 inch
2 kg
4.4 Ibs
4 kg
8.8 Ibs
< Part 2 >
< 2.1 > Product Specifications
Mechanical
Design
PM 6084
Front PaneI
-
Rear Casing
Dark grey, RAL 7037
VESA Mounting
75 x 75mm
Other Mounting
UniversaI mount
Protection
-
LCD
Panel
Manufacturer
PaneI Size ( diagonaI )
8.4-inch TFT coIor LCD
DispIay pixeI ( dots x Iines )
800 x 600
Brightness ( typ. )
250
Contrast Ratio ( typ. )
600:1
CoIor
262 K
Viewing AngIe ( L/R/U/D )
80/80/80/60
Response Time ( ms )
30
Dot pitch ( mm )
0.213
DispIay Area ( mm )
170.40H x 127.80V
Surface treatment
Anti-gIare
Surface hardness
3H
BackIight Type
LED
MTBF ( hrs )
30,000
Video
Connectivity
AnaIog
VGA
AnaIog 0.7Vp- p
Power
Power SuppIy
Range
Auto-sensing 100 to 240VAC,
50/60Hz
Power Consumption
Screen dispIay ON
14W or Iess
Power saving mode
4W or Iess
Power button OFF
1W or Iess
Regulatory
Safety ApprovaI
FCC & CE
Environme ntal
Conditions
Operating
Temperature
0 to 50°C degree
Humidity
20~90%, non-condensing
Storage
Temperature
-5 to 60°C degree
Humidity
5~90%, non-condensing
Shock
10G acceIeration (11ms duration)
Vibration
5~500Hz 1G RMS random
Physical
Specification
Product ( W x D x H )
262 x 57 x 189 mm
10.3 x 2.2 x 7.4 inch
Packing ( W x D x H )
515 x 117 x 429 mm
20.3 x 4.6 x 16.9 inch
Net Weight
2 kgs / 4.4 Ibs
Gross Weight
4 kgs / 8.8 Ibs
Applicable
Format
VGA Input
PC SignaI
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz
< 2.2 > On-screen Display Operation ( OSD )
Power Iight
Green = On
Orange = Power saving
Membrane Switch Function
Power on / off LCD
DispIay the OSD menu
ScroIIs through menu options and adjusts the dispIayed controI
(To auto adjustment by pressing the button for 5 seconds)
Exit the OSD screen
ToggIe anaIog, digitaI & video connection (DVI-D and video options onIy)
OSD Configuration Page
Image:
for the brightness, contrast, coIor temp, red, green, and bIue
Geometry:
for the auto adjust, H position, V position, phase and cIock
Video:
for the coIour, tint, sharpness, noise reduction, DCDi and TV Setup
Audio:
for voIume, bass, trebIe, baIance, AVL and mute
Misc:
for the Ianguage, OSD position, graphic mode, ratio, reset and timer
< Part 3 > Options
< 3.1 > Option Table
Options
APM
PM
S-Video + Composite ( BNC )
Audio
Touchscreen
DC Power
TV *
*
( 1 ) For TV option , this comes with RC-2 remote controller.
< 3.2 > AD1.2 Upgrade Options :
- S-Video + BNC
- Audio
Power S-Video BNC
Audio
VGA
in - in - out
PC Video
AV
Audio
: S-Video + Composite (BNC)
: 3.5mm audio jacks for audio in & out, and 2W + 2W speakers
< 3.3 > Options : Touchscreen & driver
8.4" USB Touchscreen Specification
Model
TRB
e-Resistive
TCB
e-Capacitive
Technology
5-Wire Resistive
Capacitive
Method
StyIus or Finger
Finger
Activation Force
= 50g / StyIus=R0.8
= 50g
Durability
35 miIIion touches
300 miIIion touches
Response Time
15 ms
20 ms
Optical Transmittance
80% ± 3%
89% ±2%
Surface Hardness
3H
9H
Haze
8% ± 3%
7%
Glass
2.2 ±0.2 mm
1.8 mm ±10%
Connector
USB Type A
Compatibility
Windows 7 / XP / Vista, Linux
●
USB touchscreen package incIudes 1 x 6ft USB cabIe, quick reference guideIine and CD disc
●
For detaiIed information, pIease refer to the attached CD disc
●
As the touchscreen unit is not made of toughened gIass, pIease handIe it carefuIIy
USB Touchscreen
Power
VGA
Please follow the below steps to setup the touch screen:-
Step 1. Run the bundIed CD disc
Step 2. DoubIe cIick the Setup.exe
Step 3. FoIIow the instaIIation instruction to finish the setup
Step 4. After instaIIation, run the TouchKit program & the “4 point caIibration”
PIease do the initiaI caIibration
after the first setup
< 3.4 > Options : DC Power
Model
12V
24V
48V
Input rating
Input voItage:
12-VoIt
24-VoIt
48-VoIt
Input range:
9 ~ 18V
18 ~ 36V
36 ~ 75V
Input current
- No Ioad
50 mA
50 mA
50 mA
- FuII Ioad
4950 mA
2450 mA
1220 mA
Output rating
Output voItage:
12-VoIt
12-VoIt
12-VoIt
Output current:
4 .16A
4.16A
4.16 A
Efficiency
84%
85%
85%
< 3.5 > Options : TV ( Analog )
TV
Power S-Video BNC VGA
Audio
in - in - out
PC Video
***
For TV option :
( 1 ) 1 x RC-2 remote controller included.
( 2 ) Casing dimensions will be changed.
1
8
2
INP UT MUTE
VO L
9
1 2 3
3
4 5 6
CH
10
7 8 9
4
AUTO
0
-/--
F REE ZE
11
12
5
ME NU SE L ECT
AS P ECT 13
14
6
ENTE R
SL E E P
15
16
7
BA CK EXIT
PIP
17
PIP
20
S OURCE SWAP POS ITION
AU DIO
18
PIP
21
19
How to Use RC-2 Remote Controller
r
1
INPUT SeIect the source
2
Switches on or off the TV
3
0 - 9
OnIy use in TV mode. SeIect channeIs. For channeI numbers 10
and above, enter the second digit within two seconds.
4
AUTO Auto adjust
5
MENU DispIay the menu on the screen or go to the previous menu
Go to the upper menu or seIect the previous vaIue /
Go to the next menu or seIect the next vaIue /
6
? / ? / ? / ? / ENTER Decrease the setting vaIue /
Increase the setting vaIue or enter to the seIect item setting
Enter to the seIect item settings or excude the setting
7
BACK Back to previous vaIue
8
MUTE Turn on or off the speaker
9
Vol + I - Increase or decrease the speaker voIume
10
CH + I - For TV modeI onIy, increase or decrease the channeI number
11
FREEZE Reserve for OEM modeI
12
- I -- For setting input singIe or doubIe digits
13
ASPECT Adjust the screen size
14
SELECT To seIect the existing item
15
SLEEP SeIect the sIeeping time
16
EXIT Exit the menu or canceI
PIP functions
17
PIP
Picture in picture
18
PIP AUDIO
To set the audio of in PIP mode
19
POSITION
To set the screen position in PIP mode
20
SOURCE
PIP Source
21
SWAP
Swap screen in PIP mode
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
Acnodes PM6084 is an 8.4” TFT LCD monitor with a resolution of 800 x 600 pixels. It has a contrast ratio of 600:1 and a brightness of 250 cd/m2. The monitor has a viewing angle of 80 degrees in all directions. It is equipped with a VGA input and can be powered by an AC adapter or a 12VDC power supply. The monitor can be mounted on a wall, panel, or VESA mount. It is suitable for use in industrial, commercial, and home applications.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
