GETTING STARTED
1. Please read the safety section (page 2) in the main instructions before proceeding further. This section
contains vital information to ensure safe positioning and use of the TV
2. Unpack the TV and place on a flat level surface suitable to support the weight of the TV (9.14 kg). This will require
two persons to lift the TV safely. Place the TV face down and fit the base as described overleaf.
3. Connect the aerial into the TV Tuner connector at the rear of the TV (Fig 1).
Fig.2
4. Connect the mains power lead to the mains supply and switch on. The LED indicator
on the TV will illuminate and show red (Fig 2).
5. Open the battery compartment cover (Fig 3) on the reverse of the remote control.
Insert 2 x AAA 1.5V alkaline batteries in accordance with the diagram in the battery
compartment. Take care to observe the correct polarity (+/-). Refit the battery
compartment cover
6. Press the POWER button (Fig 4) to turn the TV set on. The LED indicator will turn
green and after a few seconds, the screen will activate and the first time installation
menu (Fig. 5) will appear.
7. Use the cursor ▼/▲ buttons on the remote control to move up and down the display
to highlight desired options.
8. The default language is “English” if you want another language select that language
using the ►/◄ buttons and press OK.
9. Select AUTOTUNING and press OK. Fig 6 will be displayed, using the ▲/▼ buttons
select to country of use (UK is default). Select START and press OK, the TV will now
search the entire UHF range for both digital and Analog TV stations. See Fig 7. When
search is complete the TV will display the first channel (BBC1) in DVBt mode.
Fig.5
Fig 1
Fig.7
WATCHING TV (basic operation)
10. To select a channel either enter the number of the channel using the number buttons
on the remote control or scroll through the channels using the channel CH+/-
buttons.
11. To view analogue TV channels press the SOURCE button to display the source
menu. Using the cursor ▲ / ▼ buttons highlight TV on the menu and press OK to
select. To view digital TV channels select DTV on this same menu.
12. To check the list of channels stored, press the CH.LIST button to display the channel
list and use the cursor ▲ / ▼ buttons to move up and down the display. To select a
channel, highlight the channel on the list and press OK to confirm.
13. Adjust the volume to the desired level using the volume or cursor ◄ / ►buttons.
The sound can be silenced by pressing the MUTE button on the remote control and
a mute symbol will appear on the screen. Press the MUTE button a second time to
restore the sound.
14. To switch off the TV for short periods, press the POWER button. The TV will go into
standby mode and the LED indicator will change to red. If not using the TV for
extended periods turn off at the mains switch to conserve electricity, all settings will
be retained.
ALED3211E 3U
Quick Start Guide and Base fitting Instructions
Fig.6
Fig.3
Fig.4
For advanced operation of this TV please consult the Instruction Manual.
Should you have difficulty in operating this unit, please consult the Trouble -
Shooting Guide in the Instruction Manual. If you suspect a fault, please contact
the Customer Help Line, details of which can be found in the Instruction Manual.
Base fitting and removal.
Place the TV face
down on a suitable
surface with the base
mounting facing
towards you (Fig 1).
Ensure the decorative ring is in position and place the base plate onto the TV
Fit the four screws (4mm x 12mm) provided into the holes as shown in Fig 2. Tighten
using a No 1 Posi screwdriver. Ensure the Base Plate is facing the correct way (Fig 3)
If wall mounting the TV see page 22 in the Main Instruction book.
Fig 1
Fig 2
Fig 3
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Akura APLDVD1621W-HDID Quick start guide
-
Akura APLDVD2YR1968VH Quick start guide
-
-
-
-
-
-
-
-