VTech VM3252-2 Quick start guide
- Category
- Baby video monitors
- Type
- Quick start guide
What’s in the box
Once you power on your baby monitor, your parent unit displays image from baby unit, and the LINK LED light
turns on.
The POWER LED light of baby unit turns on.
Status checkConnect and power on - Baby unit Connect and power on - Parent unit
CAUTION
• The default volume of your parent unit
is level 4. If you experience high-pitched
screeching noise from your baby monitor
while positioning:
- Make sure your baby unit and parent unit
are more than 3 feet (1 meter) apart, OR
- Turn down the volume of your parent unit.
VM3252-2 baby monitor system
Baby’s room Living room
Go to www.vtechphones.com
to register your product for
enhanced warranty support
and latest VTech product news.
VM3252-2
Quick start guide
> 3ft (1m)
Install the battery
Overview - Parent unit
Stand
On/off
TALK
Zoom
Light indicators
LCD ON /OFF
Arrow keys
MENU/SELECT
Power jack
Speaker
VOL
-
VOL
+
3ft (1m)
3ft (1m)
Overview - Baby unit
Camera
Microphone
Light sensor
Infrared LEDs
Speaker
ON/OFF switch
THIS SIDE UP
POWER LED light
6U]KXOTMUT
6U]KXOTMUT
2s
Specifications are subject to change without notice.
© 2017 VTech Communications, Inc. All rights reserved.
10/17. VM3252-2_QSG_V1.
Document order number: 96-011939-010-100
Basic operation - Parent unit
Adjust speaker volume
Press VOL - or VOL +
to adjust your parent unit
speaker volume. It determines the volume of sound
transmitted from your baby units.
Zoom
Press to zoom in or out.
Talk to your baby unit
Press and hold TALK and speak to your parent unit.
Your voice is transmitted to the baby unit.
Turn off the screen
Press and hold LCD ON/OFF to switch off the screen.
You can still hear sound from the selected baby unit.
Turn off the parent unit
Press and hold to power off your parent unit.
Basic operation - Baby unit
Night vision
The baby unit has infrared LEDs that allow you to
see your baby at night or in a dark room. When
the baby unit detects low light levels, the infrared
LEDs turn on automatically. The images from this
baby unit is in black and white, and appears
on screen.
NOTES
• I t is norma l if you see a s hort wh ite glare on your
parent un it screen as the ba by unit is ad apting t o the
dark environment.
• W hen the in frared LED s are on, th e image is i n
black an d white. Th is is nor mal due to ex ternal l ight
sources.
TIP
• Depending on the surroundings and other
interfering factors, like lightings, objects, colors and
backgrounds, the display resolution may vary. Adjust
the baby unit’s angle, or place the baby unit at a
higher level to prevent glare and blurry display.
Turn off the baby unit
Slide the ON/OFF switch to OFF to power off
your baby unit.
Drill two holes in the wall (7/32
inch drill bit). If you drill the holes
into a stud, insert the screws into
the holes.
Tighten the screws until only 1/4
inch of the screws are exposed.
Mount the baby monitor (optional)
Use a pencil to mark two holes in
parallel. Make sure they are the
same distance apart as the mount-
ing holes on the baby unit.
NOTES
• Check for reception strength and
camera angle before drilling the holes.
Align the mounting holes on the
baby unit with the screws on the
wall.
Slide the mounting holes on the
baby unit down until it locks into
place.
6U]KXOTMULL
6U]KXOTMULL
2s
Long press
Press to switch to another camera in SINGLE-CAM mode.
Change different views - View
Change different views - Patrol
In PATROL mode:
1. Press MENU when the parent unit is idle.
2. Press or to choose , then press .
3.
Press or to switch on or off PATROL mode, then press SELECT to confirm your selection.
Sound activation
Automatically turns on the parent unit screen when the baby
unit being viewed detects a sound after the screen is turned
off. When no sound is detected within 50 seconds, the
screen is automatically turned off to save power.
Press .
10s
63℉
> More than 1
meter (3 feet)
63℉
Long press
Use the menu
Press MENU to enter the main menu, or save a setting.
While in the main menu:
• Press or to scroll among the menu options.
• Press to enter the desired submenu.
• Press MENU to exit the main menu.
While in the submenu:
• Press or to scroll among the submenu options.
• Press to enter the desired 2nd level submenu.
• Press SELECT to confirm your selection.
• Press to exit the submenu.
-
1
-
2
VTech VM3252-2 Quick start guide
- Category
- Baby video monitors
- Type
- Quick start guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
VTech VM3252-2 Quick start guide
-
VTech VM3252 Quick start guide
-
VTech VM3261 Quick start guide
-
-
-
-
-
-
-