Bosch PST 700 E Owner's manual

Robert Bosch GmbH

Power Tools Division

70745 Leinfelden-Echterdingen

Germany

www.bosch-pt.com

2 609 003 949 (2009.09) T / 123 WEU

Low Vibr

ation

PST 700 E

de Originalbetriebsanleitung

en Original instructions

fr Notice originale

es Manual original

pt Manual original

it Istruzioni originali

nl Oorspronkelijke gebruiksaanwijzing

da Original brugsanvisning

sv Bruksanvisning i original

no Original driftsinstruks

fi Alkuperäiset ohjeet

el Πρωτότυπο οδηγιών χρήσης

tr Orijinal işletme talimat

OBJ_BUCH-1067-001.book Page 1 Monday, September 28, 2009 8:32 AM

2 609 003 949 | (28.9.09) Bosch Power Tools

2 |

0°

45°

45

°

0

°

45

°

45

°

12

10

11

43

5

13 88713

6789

PST 700 E

1 2

A

OBJ_BUCH-1067-001.book Page 2 Monday, September 28, 2009 8:35 AM

| 3

Bosch Power Tools 2 609 003 949 | (28.9.09)

0

˚

45

˚

45

˚

0˚

45

˚

45

˚

16

17

7

8

5

17

18

1 2

5159

10

14

5

D E

F

CB

OBJ_BUCH-1067-001.book Page 3 Monday, September 28, 2009 8:35 AM

2 609 003 949 | (28.9.09) Bosch Power Tools

4 |

15 1520 19 20 21

G H

OBJ_BUCH-1067-001.book Page 4 Monday, September 28, 2009 8:35 AM

| 5

Bosch Power Tools 2 609 003 949 | (28.9.09)

Deutsch. . . . . . . . . . . . . . . . . . . . . . . . . . . . Seite 6

English. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 15

Français. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 24

Español . . . . . . . . . . . . . . . . . . . . . . . . . . . Página 34

Português . . . . . . . . . . . . . . . . . . . . . . . . . Página 44

Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . Pagina 53

Nederlands . . . . . . . . . . . . . . . . . . . . . . . . Pagina 62

Dansk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Side 71

Svenska. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sida 79

Norsk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Side 87

Suomi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sivu 95

Ελληνικά . . . . . . . . . . . . . . . . . . . . . . . . . . . Σελίδα 103

Türkçe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sayfa 113

OBJ_BUCH-1067-001.book Page 5 Monday, September 28, 2009 8:35 AM

6 | Deutsch

2 609 003 949 | (28.9.09) Bosch Power Tools

de

Sicherheitshinweise

Allgemeine Sicherheitshinweise für

Elektrowerkzeuge

Lesen Sie alle Sicherheitshin-

weise und Anweisungen. Ver-

säumnisse bei der Einhaltung der Sicherheits-

hinweise und Anweisungen können elektrischen

Schlag, Brand und/oder schwere Verletzungen

verursachen.

Bewahren Sie alle Sicherheitshinweise und An-

weisungen für die Zukunft auf.

Der in den Sicherheitshinweisen verwendete

Begriff „Elektrowerkzeug“ bezieht sich auf netz-

betriebene Elektrowerkzeuge (mit Netzkabel)

und auf akkubetriebene Elektrowerkzeuge

(ohne Netzkabel).

1) Arbeitsplatzsicherheit

a) Halten Sie Ihren Arbeitsbereich sauber

und gut beleuchtet. Unordnung oder un-

beleuchtete Arbeitsbereiche können zu

Unfällen führen.

b) Arbeiten Sie mit dem Elektrowerkzeug

nicht in explosionsgefährdeter Umge-

bung, in der sich brennbare Flüssigkei-

ten, Gase oder Stäube befinden. Elektro-

werkzeuge erzeugen Funken, die den

Staub oder die Dämpfe entzünden können.

c) Halten Sie Kinder und andere Personen

während der Benutzung des Elektro-

werkzeugs fern. Bei Ablenkung können

Sie die Kontrolle über das Gerät verlieren.

2) Elektrische Sicherheit

a) Der Anschlussstecker des Elektrowerk-

zeuges muss in die Steckdose passen. Der

Stecker darf in keiner Weise verändert

werden. Verwenden Sie keine Adapterste-

cker gemeinsam mit schutzgeerdeten

Elektrowerkzeugen. Unveränderte Stecker

und passende Steckdosen verringern das

Risiko eines elektrischen Schlages.

b) Vermeiden Sie Körperkontakt mit geer-

deten Oberflächen wie von Rohren, Hei-

zungen, Herden und Kühlschränken. Es

besteht ein erhöhtes Risiko durch elektri-

schen Schlag, wenn Ihr Körper geerdet ist.

c) Halten Sie Elektrowerkzeuge von Regen

oder Nässe fern. Das Eindringen von Was-

ser in ein Elektrowerkzeug erhöht das Ri-

siko eines elektrischen Schlages.

d) Zweckentfremden Sie das Kabel nicht,

um das Elektrowerkzeug zu tragen, auf-

zuhängen oder um den Stecker aus der

Steckdose zu ziehen. Halten Sie das Ka-

bel fern von Hitze, Öl, scharfen Kanten

oder sich bewegenden Geräteteilen. Be-

schädigte oder verwickelte Kabel erhöhen

das Risiko eines elektrischen Schlages.

e) Wenn Sie mit einem Elektrowerkzeug im

Freien arbeiten, verwenden Sie nur Ver-

längerungskabel, die auch für den Außen-

bereich geeignet sind. Die Anwendung ei-

nes für den Außenbereich geeigneten

Verlängerungskabels verringert das Risiko

eines elektrischen Schlages.

f) Wenn der Betrieb des Elektrowerkzeu-

ges in feuchter Umgebung nicht ver-

meidbar ist, verwenden Sie einen Fehler-

stromschutzschalter. Der Einsatz eines

Fehlerstromschutzschalters vermindert

das Risiko eines elektrischen Schlages.

3) Sicherheit von Personen

a) Seien Sie aufmerksam, achten Sie darauf,

was Sie tun, und gehen Sie mit Vernunft

an die Arbeit mit einem Elektrowerkzeug.

Benutzen Sie kein Elektrowerkzeug,

wenn Sie müde sind oder unter dem Ein-

fluss von Drogen, Alkohol oder Medika-

menten stehen. Ein Moment der Unacht-

samkeit beim Gebrauch des Elektrowerk-

zeuges kann zu ernsthaften Verletzungen

führen.

b) Tragen Sie persönliche Schutzausrüstung

und immer eine Schutzbrille. Das Tragen

persönlicher Schutzausrüstung, wie

Staubmaske, rutschfeste Sicherheitsschu-

he, Schutzhelm oder Gehörschutz, je nach

Art und Einsatz des Elektrowerkzeuges,

verringert das Risiko von Verletzungen.

c) Vermeiden Sie eine unbeabsichtigte Inbe-

triebnahme. Vergewissern Sie sich, dass

das Elektrowerkzeug ausgeschaltet ist,

bevor Sie es an die Stromversorgung

WARNUNG

OBJ_BUCH-1067-001.book Page 6 Monday, September 28, 2009 8:35 AM

Page is loading ...

Deutsch | 13

Bosch Power Tools 2 609 003 949 | (28.9.09)

Hubzahl steuern

Sie können die Hubzahl des eingeschalteten Elek-

trowerkzeugs stufenlos regulieren, je nachdem,

wie weit Sie den Ein-/Ausschalter 2 eindrücken.

Bei arretiertem Ein-/Ausschalter 2 ist die Redu-

zierung der Hubzahl nicht möglich.

Die erforderliche Hubzahl ist vom Werkstoff und

den Arbeitsbedingungen abhängig und kann

durch praktischen Versuch ermittelt werden.

Eine Verringerung der Hubzahl wird beim Auf-

setzen des Sägeblattes auf das Werkstück sowie

beim Sägen von Kunststoff und Aluminium emp-

fohlen.

Bei längerem Arbeiten mit kleiner Hubzahl kann

sich das Elektrowerkzeug stark erwärmen. Ent-

nehmen Sie das Sägeblatt und lassen Sie das

Elektrowerkzeug zur Abkühlung ca. 3 min mit

maximaler Hubzahl laufen.

Arbeitshinweise

f Ziehen Sie vor allen Arbeiten am Elektro-

werkzeug den Netzstecker aus der Steck-

dose.

f Verwenden Sie beim Bearbeiten kleiner

oder dünner Werkstücke immer eine stabile

Unterlage oder eine Sägestation (Bosch

PLS 300).

Tauchsägen (siehe Bild F)

f Es dürfen nur weiche Werkstoffe wie Holz,

Gipskarton o.Ä. im Tauchsägeverfahren be-

arbeitet werden!

Verwenden Sie zum Tauchsägen nur kurze Säge-

blätter. Tauchsägen ist nur mit einem Gehrungs-

winkel von 0° möglich.

Setzen Sie das Elektrowerkzeug mit der vorde-

ren Kante der Fußplatte 5 auf das Werkstück

auf, ohne dass das Sägeblatt 8 das Werkstück

berührt, und schalten Sie es ein. Wählen Sie bei

Elektrowerkzeugen mit Hubzahlsteuerung die

maximale Hubzahl. Drücken Sie das Elektro-

werkzeug fest gegen das Werkstück und lassen

Sie das Sägeblatt langsam in das Werkstück ein-

tauchen.

Sobald die Fußplatte 5 ganzflächig auf dem

Werkstück aufliegt, sägen Sie entlang der ge-

wünschten Schnittlinie weiter.

Parallelanschlag mit Kreisschneider (Zubehör)

Für Arbeiten mit dem Parallelanschlag mit Kreis-

schneider 19 (Zubehör) darf die Stärke des

Werkstückes maximal 30 mm betragen.

Entfernen Sie den Sockel für „Cut Control“ 10

aus der Fußplatte 5. Drücken Sie dazu den So-

ckel leicht zusammen und nehmen Sie ihn aus

der Führung 15 heraus.

Parallelschnitte (siehe Bild G): Lösen Sie die

Feststellschraube 20 und schieben Sie die Skala

des Parallelanschlags durch die Führung 15 in

der Fußplatte. Stellen Sie die gewünschte

Schnittbreite als Skalenwert an der Innenkante

der Fußplatte ein. Drehen Sie die Feststell-

schraube 20 fest.

Kreisschnitte (siehe Bild H): Bohren Sie an der

Schnittlinie innerhalb des zu sägenden Kreises

ein Loch, das zum Durchstecken des Sägeblat-

tes ausreicht. Bearbeiten Sie die Bohrung mit ei-

ner Fräse oder Feile, damit das Sägeblatt bündig

an der Schnittlinie anliegen kann. Setzen Sie die

Feststellschraube 20 auf die andere Seite des

Parallelanschlags. Schieben Sie die Skala des

Parallelanschlags durch die Führung 15 in der

Fußplatte. Bohren Sie im Werkstück in der Mitte

des zu sägenden Ausschnittes ein Loch. Stecken

Sie die Zentrierspitze 21 durch die innere Öff-

nung des Parallelanschlags und in das gebohrte

Loch. Stellen Sie den Radius als Skalenwert an

der Innenkante der Fußplatte ein. Drehen Sie

die Feststellschraube 20 fest.

Kühl-/Schmiermittel

Beim Sägen von Metall sollten Sie wegen der Er-

wärmung des Materials entlang der Schnittlinie

Kühl- bzw. Schmiermittel auftragen.

OBJ_BUCH-1067-001.book Page 13 Monday, September 28, 2009 8:35 AM

Page is loading ...

English | 15

Bosch Power Tools 2 609 003 949 | (28.9.09)

en

Safety Notes

General Power Tool Safety Warnings

Read all safety warnings and all

instructions. Failure to follow

the warnings and instructions may result in elec-

tric shock, fire and/or serious injury.

Save all warnings and instructions for future

reference.

The term “power tool” in the warnings refers to

your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit. Clut-

tered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away

while operating a power tool. Distrac-

tions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do not

use any adapter plugs with earthed

(grounded) power tools. Unmodified

plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or

grounded surfaces, such as pipes, radia-

tors, ranges and refrigerators. There is

an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges and moving parts.

Damaged or entangled cords increase the

risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for out-

door use. Use of a cord suitable for out-

door use reduces the risk of electric

shock.

f) If operating a power tool in a damp loca-

tion is unavoidable, use a residual cur-

rent device (RCD) protected supply. Use

of an RCD reduces the risk of electric

shock.

3) Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool

while you are tired or under the influ-

ence of drugs, alcohol or medication.

A moment of inattention while operating

power tools may result in serious person-

al injury.

b) Use personal protective equipment. Al-

ways wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protec-

tion used for appropriate conditions will

reduce personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or bat-

tery pack, picking up or carrying the tool.

Carrying power tools with your finger on

the switch or energising power tools that

have the switch on invites accidents.

d) Remove any adjusting key or wrench be-

fore turning the power tool on. A wrench

or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in unex-

pected situations.

f) Dress properly. Do not wear loose cloth-

ing or jewellery. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewellery or long hair can

be caught in moving parts.

WARNING

OBJ_BUCH-1067-001.book Page 15 Monday, September 28, 2009 8:35 AM

16 | English

2 609 003 949 | (28.9.09) Bosch Power Tools

g) If devices are provided for the connec-

tion of dust extraction and collection fa-

cilities, ensure these are connected and

properly used. Use of dust collection can

reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the cor-

rect power tool for your application. The

correct power tool will do the job better

and safer at the rate for which it was de-

signed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the

switch is dangerous and must be re-

paired.

c) Disconnect the plug from the power

source and/or the battery pack from the

power tool before making any adjust-

ments, changing accessories, or storing

power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfa-

miliar with the power tool or these in-

structions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for mis-

alignment or binding of moving parts,

breakage of parts and any other condi-

tion that may affect the power tool’s op-

eration. If damaged, have the power tool

repaired before use. Many accidents are

caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Prop-

erly maintained cutting tools with sharp

cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool

bits etc. in accordance with these in-

structions, taking into account the work-

ing conditions and the work to be per-

formed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qual-

ified repair person using only identical

replacement parts. This will ensure that

the safety of the power tool is maintained.

Safety Warnings for Jigsaws

f Hold power tool by insulated gripping sur-

faces, when performing an operation where

the cutting accessory may contact hidden

wiring or its own cord. Cutting accessory

contacting a “live” wire may make exposed

metal parts of the power tool “live” and

could give the operator an electric shock.

f Keep hands away from the sawing range.

Do not reach under the workpiece. Contact

with the saw blade can lead to injuries.

f Apply the machine to the workpiece only

when switched on. Otherwise there is dan-

ger of kickback when the cutting tool jams in

the workpiece.

f Pay attention that the base plate 5 rests

securely on the material while sawing.

A jammed saw blade can break or lead to

kickback.

f When the cut is completed, switch off the

machine and then pull the saw blade out of

the cut only after it has come to a standstill.

In this manner you can avoid kickback and

can place down the machine securely.

f Use only sharp, flawless saw blades. Bent or

unsharp saw blades can break or cause kick-

back.

f Do not brake the saw blade to a stop by ap-

plying side pressure after switching off. The

saw blade can be damaged, break or cause

kickback.

f Use suitable detectors to determine if utili-

ty lines are hidden in the work area or call

the local utility company for assistance.

Contact with electric lines can lead to fire

and electric shock. Damaging a gas line can

lead to explosion. Penetrating a water line

causes property damage or may cause an

electric shock.

OBJ_BUCH-1067-001.book Page 16 Monday, September 28, 2009 8:35 AM

English | 17

Bosch Power Tools 2 609 003 949 | (28.9.09)

f Secure the workpiece. A workpiece clamped

with clamping devices or in a vice is held

more secure than by hand.

f Keep your workplace clean. Blends of mate-

rials are particularly dangerous. Dust from

light alloys can burn or explode.

f Always wait until the machine has come to

a complete stop before placing it down. The

tool insert can jam and lead to loss of control

over the power tool.

f Never use the machine with a damaged ca-

ble. Do not touch the damaged cable and

pull the mains plug when the cable is dam-

aged while working. Damaged cables in-

crease the risk of an electric shock.

f Products sold in GB only: Your product is fit-

ted with an BS 1363/A approved electric

plug with internal fuse (ASTA approved to

BS 1362).

If the plug is not suitable for your socket out-

lets, it should be cut off and an appropriate

plug fitted in its place by an authorised cus-

tomer service agent. The replacement plug

should have the same fuse rating as the orig-

inal plug.

The severed plug must be disposed of to

avoid a possible shock hazard and should nev-

er be inserted into a mains socket elsewhere.

Products sold in AUS and NZ only: Use a re-

sidual current device (RCD) with a rated re-

sidual current of 30 mA or less.

Functional Description

Read all safety warnings and all in-

structions. Failure to follow the

warnings and instructions may re-

sult in electric shock, fire and/or se-

rious injury.

Intended Use

The machine is intended for making separating

cuts and cut-outs in wood, plastic, metal, ce-

ramic plates and rubber while resting firmly on

the workpiece. It is suitable for straight and

curved cuts with mitre angles to 45°. The saw

blade recommendations are to be observed.

Product Features

The numbering of the product features refers to

the illustration of the machine on the graphics

page.

1 Lock-off button for On/Off switch

2 On/Off switch

3 Vacuum hose*

4 Vacuum connection

5 Base plate

6 Switch for sawdust blowing device

7 Guide roller

8 Saw blade*

9 “Cut Control” viewing window*

10 “Cut Control” base*

11 Contact protector

12 Handle (insulated gripping surface)

13 Saw blade holder

14 Splinter guard*

15 Lead for the parallel guide

16 Holder for guide roller

17 Screw

18 Scale for mitre angle

19 Parallel guide with circle cutter*

20 Locking screw for parallel guide*

21 Centring tip of the parallel guide*

22 Cutting mark, 0°

23 Cutting mark, 45°

*Accessories shown or described are not part of the

standard delivery scope of the product. A complete

overview of accessories can be found in our acces-

sories program.

OBJ_BUCH-1067-001.book Page 17 Monday, September 28, 2009 8:35 AM

18 | English

2 609 003 949 | (28.9.09) Bosch Power Tools

Technical Data

Noise/Vibration Information

Measured sound values determined according

to EN 60745.

Typically the A-weighted noise levels of the prod-

uct are: Sound pressure level 88 dB(A); Sound

power level 99 dB(A). Uncertainty K =3 dB.

Wear hearing protection!

Vibration total values (triax vector sum) deter-

mined according to EN 60745:

Cutting board: Vibration emission value

a

h

=10 m/s

2

, Uncertainty K=3 m/s

2

,

Cutting sheet metal: Vibration emission value

a

h

=11 m/s

2

, Uncertainty K=3 m/s

2

.

The vibration emission level given in this infor-

mation sheet has been measured in accordance

with a standardised test given in EN 60745 and

may be used to compare one tool with another.

It may be used for a preliminary assessment of

exposure.

The declared vibration emission level repre-

sents the main applications of the tool. However

if the tool is used for different applications, with

different accessories or poorly maintained, the

vibration emission may differ. This may signifi-

cantly increase the exposure level over the total

working period.

An estimation of the level of exposure to vibra-

tion should also take into account the times

when the tool is switched off or when it is run-

ning but not actually doing the job. This may sig-

nificantly reduce the exposure level over the to-

tal working period.

Identify additional safety measures to protect

the operator from the effects of vibration such

as: maintain the tool and the accessories, keep

the hands warm, organisation of work patterns.

Declaration of Conformity

We declare under our sole responsibility that

the product described under “Technical Data” is

in conformity with the following standards or

standardization documents: EN 60745 accord-

ing to the provisions of the directives

2004/108/EC, 98/37/EC (until 28 Dec 2009),

2006/42/EC (from 29 Dec 2009).

Technical file at:

Robert Bosch GmbH, PT/ESC,

D-70745 Leinfelden-Echterdingen

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

Leinfelden, 02.09.2009

Jigsaw PST 700 E

Article number

3 603 CA0 0..

Stroke rate control

z

Rated power input

W 500

Output power

W 300

Stroke rate at no load n

0

min

-1

500–3100

Stroke

mm 20

Cutting capacity, max.

–in wood

– in aluminium

– in non-alloy steel

mm

70

10

4

Bevel cuts (left/right),

max.

°45

Weight according to

EPTA-Procedure

01/2003

kg 1.6

Protection class

/II

The values given are valid for nominal voltages [U] of

230/240 V. For lower voltage and models for specific

countries, these values can vary.

Please observe the article number on the type plate of

your machine. The trade names of the individual ma-

chines may vary.

Dr. Egbert Schneider

Senior Vice President

Engineering

Dr. Eckerhard Strötgen

Head of Product

Certification

OBJ_BUCH-1067-001.book Page 18 Monday, September 28, 2009 8:35 AM

English | 19

Bosch Power Tools 2 609 003 949 | (28.9.09)

Assembly

f Before any work on the machine itself, pull

the mains plug.

Replacing/Inserting the Saw Blade

f When mounting the saw blade, wear protec-

tive gloves. Danger of injury when touching

the saw blade.

Selecting a Saw Blade

An overview of recommended saw blades can

be found at the end of these instructions. Use

only T-shank saw blades or saw blades with 1/4"

universal shank (U-shank). The saw blade

should not be longer than required for the in-

tended cut.

Use a thin saw blade for narrow curve cuts.

Inserting the Saw Blade (see figure A1)

f Clean the shank of the saw blade before in-

serting it. An unclean shank cannot be fas-

tened securely.

Push the saw blade holder 13 upward in the di-

rection of the arrow. Insert the saw blade 8

(teeth in cutting direction) to the stop into the

saw blade holder.

While inserting the saw blade, pay attention that

the back of the saw blade is positioned in the

groove of the guide roller 7.

Precise cuts are only possible when the guide

roller 7 faces closely but not too tight against

the back of the saw blade (the saw blade 8 may

not be bent by the guide roller). If required,

loosen screw 17 and move the holder 16 of the

guide roller in such a manner that the guide roll-

er faces closely against the back of the saw

blade. Tighten screw 17 again.

f Check the tight seating of the saw blade. A

loose saw blade can fall out and lead to inju-

ries.

Removing the Saw Blade (see figure A2)

Push the saw blade holder 13 upward in the di-

rection of the arrow and remove the saw blade 8.

Splinter Guard (see figure B)

The splinter guard 14 (accessory) can prevent

fraying of the surface while sawing wood. The

splinter guard can only be used for certain saw

blade types and only for cutting angles of 0°.

When sawing with the splinter guard, the base

plate 5 must not be moved back for cuts that are

close to the edge.

Press the splinter guard 14 from the bottom into

the base plate 5.

“Cut Control” (Accessory)

“Cut Control” enables precise guiding of the

power tool along a cutting line marked on the

workpiece. The “Cut Control” kit includes the

viewing window 9 with cutting marks and the

base 10 for attachment to the power tool.

Attaching “Cut Control” to the Base Plate

(see figure C)

Clamp the “Cut Control” 9 viewing window into

the holders of the base 10. Then, lightly press

the base together and allow it to engage into the

lead 15 of the base plate 5.

Dust/Chip Extraction

f Dusts from materials such as lead-containing

coatings, some wood types, minerals and

metal can be harmful to one’s health. Touch-

ing or breathing-in the dusts can cause aller-

gic reactions and/or lead to respiratory infec-

tions of the user or bystanders.

Certain dusts, such as oak or beech dust, are

considered as carcinogenic, especially in

connection with wood-treatment additives

(chromate, wood preservative). Materials

containing asbestos may only be worked by

specialists.

– Use dust extraction whenever possible.

– Provide for good ventilation of the work-

ing place.

– It is recommended to wear a P2 filter-

class respirator.

Observe the relevant regulations in your

country for the materials to be worked.

OBJ_BUCH-1067-001.book Page 19 Monday, September 28, 2009 8:35 AM

20 | English

2 609 003 949 | (28.9.09) Bosch Power Tools

Connecting the Dust Extraction

Place a vacuum hose 3 (accessory) onto the vac-

uum connection 4. Connect the vacuum hose 3

with a vacuum cleaner (accessory). An overview

for the connection of various vacuum cleaners

can be found at the end of these instructions.

Switch the saw dust blower off when a dust ex-

traction system is connected (see “Sawdust

Blower Device”).

The vacuum cleaner must be suitable for the ma-

terial being worked.

When vacuuming dry dust that is especially det-

rimental to health or carcinogenic, use a special

vacuum cleaner.

Operation

Operating Modes

f Before any work on the machine itself, pull

the mains plug.

Adjusting the Cutting Angle (see figures D–E)

The base plate 5 can be swivelled by 45° to the

left or right for mitre cuts.

Insert a saw blade 8.

The splinter guard 14 can not be inserted for mi-

tre cuts.

Loosen the screw 17 and lightly slide the base

plate 5 toward the vacuum connection 4.

For adjustment of precise mitre angles, the base

plate has adjustment notches on the left and

right at 0°, 22.5° and 45°. Swivel the base plate

5 to the desired position according to the scale

18. Other mitre angles can be adjusted using a

protractor.

Afterwards, push the base plate 5 to the stop in

the direction of the saw blade 8.

Position the holder for the guide roller 16 in

such a manner that the guide roller 7 faces

against the back of the saw blade. Precise cuts

are possible only when the guide roller faces

tightly against the back of the saw blade.

Tighten the screw 17 again.

Cut Control for Bevel Cuts

For cutting-line control of bevel cuts, the “Cut

Control” viewing window 9 has a mark 22 for 0°

right-angle cuts and a mark 23 each for the left-

or rightward sloping 45° bevel cut according to

scale 18.

The cutting mark for bevel cuts between 0° and

45° results proportionally. It can additionally be

drawn on the “Cut Control” viewing window 9

with a non-permanent marker, and easily be re-

moved again.

For accurate working, it is best to carry out a

test cut.

Offsetting the Base Plate (see figure D)

For sawing close to edges, the base plate 5 can

be offset to the rear.

Insert a saw blade 8.

Loosen the screw 17 and slide the base plate 5

toward the vacuum connection 4 to the stop.

Position the holder for the guide roller 16 in

such a manner that the guide roller 7 faces

against the back of the saw blade. Precise cuts

are possible only when the guide roller faces

tightly against the back of the saw blade.

Tighten the screw 17 again.

Sawing with the base plate 5 offset is possible

only at a 0° bevel angle. Additionally, “Cut Con-

trol” may not be used together with the base 10,

the parallel guide with circle cutter 19 (accesso-

ry), as well as the splinter guard 14.

45°

0°

45°

0°

45°

0°

22

,5°

45°

22 239105 18

OBJ_BUCH-1067-001.book Page 20 Monday, September 28, 2009 8:35 AM

English | 21

Bosch Power Tools 2 609 003 949 | (28.9.09)

Sawdust Blower Device

With the air jet of the sawdust blower device 6,

the cutting line can be kept free of dust and

chips.

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V

can also be operated with 220 V.

Switching On and Off

To start the machine, press the On/Off switch 2.

To lock the On/Off switch 2, keep it depressed

and push the lock-on button 1 to the right or

left.

To switch off the machine, release the On/Off

switch 2. When the On/Off switch 2 is locked,

press it first and then release it.

Controling the Stroke Rate

Increasing or reducing the pressure on the

On/Off switch 2 enables stepless stroke-rate

control of the switched-on machine.

When the On/Off switch 2 is locked, it is not

possible to reduce the stroke rate.

The required stroke rate is dependent on the

material and the working conditions and can be

determined by a practical trial.

Reducing the stroke rate is recommended when

the saw blade engages in the material as well as

when sawing plastic and aluminium.

After longer periods of work at low stroke rate,

the machine can heat up considerably. Remove

the saw blade from the machine and allow the

machine to cool down by running it for approx.

3 minutes at maximum stroke rate.

Working Advice

f Before any work on the machine itself, pull

the mains plug.

f When working small or thin workpieces, al-

ways use a stable support or a saw station

(Bosch PLS 300).

Plunge Cutting (see figure F)

f Plunge cuts may only be applied to soft ma-

terials, such as wood, gypsum plaster

boards, etc.!

Use only short saw blades for plunge cutting.

Plunge cutting is possible only with the mitre an-

gle set at 0°.

Place the machine with the front edge of the

base plate 5 on to the workpiece without the

saw blade 8 touching the workpiece and switch

on. For machines with stroke rate control, select

the maximum stroke rate. Firmly hold the ma-

chine against the workpiece and by tilting the

machine, slowly plunge the saw blade into the

workpiece.

When the base plate 5 fully lays on the work-

piece, continue sawing along the desired cutting

line.

Parallel Guide with Circle Cutter (Accessory)

For cuts using the parallel guide with circle cut-

ter 19 (accessory), the thickness of the material

must not exceed a maximum of 30 mm.

Remove the “Cut Control” base 10 from base

plate 5. For this, lightly press the base together

and remove it from the guide 15.

Parallel Cuts (see figure G): Loosen the locking

screw 20 and slide the scale of the parallel guide

through the lead 15 in the base plate. Set the

desired cutting width as the scale value on the

inside edge of the base plate. Tighten the lock-

ing screw 20.

Switching on the sawdust blow-

er device: For cuts in materials

with high removal rate, such as

in wood, plastic, etc., push the

switch 6 toward the vacuum

connection.

Switching off the sawdust blow-

er device: For cuts in metal and

when a dust extraction system is

connected, push the switch 6 to-

ward the saw blade.

OBJ_BUCH-1067-001.book Page 21 Monday, September 28, 2009 8:35 AM

22 | English

2 609 003 949 | (28.9.09) Bosch Power Tools

Circular Cuts (see figure H): Drill a hole (large

enough to accomodate the saw blade) close to

the cutting line within the circle to be sawn.

Work the drill hole with a router or file to ensure

that the saw blade faces flush against the cut-

ting line. Reposition the locking screw 20 on the

other side of the parallel guide. Slide the scale

of the parallel guide throught the lead 15 in the

base plate. Drill a hole in the centre of the cut-

out to be sawn. Insert the centring tip 21

through the inside opening of the parallel guide

and into the drilled hole. Adjust the radius as

scale value at the inside edge of the base plate.

Tighten the locking screw 20.

Coolant/Lubricant

When sawing metal, coolant/lubricant should be

applied alongside cutting line because of the

material heating up.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

Clean the saw blade holder regularly. For this,

remove the saw blade from the machine and

lightly tap out the machine on a level surface.

Heavy contamination of the machine can lead to

malfunctions. Therefore, do not saw materials

that produce a lot of dust from below or over-

head.

f In extreme conditions, always use dust ex-

traction as far as possible. Blow out ventila-

tion slots frequently and install a residual

current device (RCD). When working metals,

conductive dust can settle in the interior of

the power tool. The total insulation of the

power tool can be impaired.

Lubricate the guide roller 7 occasionally with a

drop of oil.

Check the guide roller 7 regularly. If worn, it

must be replaced through an authorised Bosch

after-sales service agent.

If the machine should fail despite the care taken

in manufacturing and testing procedures, repair

should be carried out by an after-sales service

centre for Bosch power tools.

In all correspondence and spare parts order,

please always include the 10-digit article

number given on the type plate of the machine.

After-sales Service and Customer As-

sistance

Our after-sales service responds to your ques-

tions concerning maintenance and repair of your

product as well as spare parts. Exploded views

and information on spare parts can also be

found under:

www.bosch-pt.com

Our customer service representatives can an-

swer your questions concerning possible appli-

cations and adjustment of products and acces-

sories.

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham

Uxbridge

UB 9 5HJ

Tel. Service: +44 (0844) 736 0109

Fax: +44 (0844) 736 0146

E-Mail: [email protected]

Ireland

Origo Ltd.

Unit 23 Magna Drive

Magna Business Park

City West

Dublin 24

Tel. Service: +353 (01) 4 66 67 00

Fax: +353 (01) 4 66 68 88

OBJ_BUCH-1067-001.book Page 22 Monday, September 28, 2009 8:35 AM

English | 23

Bosch Power Tools 2 609 003 949 | (28.9.09)

Australia, New Zealand and Pacific Islands

Robert Bosch Australia Pty. Ltd.

Power Tools

Locked Bag 66

Clayton South VIC 3169

Customer Contact Center

Inside Australia:

Phone: +61 (01300) 307 044

Fax: +61 (01300) 307 045

Inside New Zealand:

Phone: +64 (0800) 543 353

Fax: +64 (0800) 428 570

Outside AU and NZ:

Phone: +61 (03) 9541 5555

www.bosch.com.au

Republic of South Africa

Customer service

Hotline: +27 (011) 6 51 96 00

Gauteng – BSC Service Centre

35 Roper Street, New Centre

Johannesburg

Tel.: +27 (011) 4 93 93 75

Fax: +27 (011) 4 93 01 26

E-Mail: [email protected]

KZN – BSC Service Centre

Unit E, Almar Centre

143 Crompton Street

Pinetown

Tel.: +27 (031) 7 01 21 20

Fax: +27 (031) 7 01 24 46

E-Mail: [email protected]

Western Cape – BSC Service Centre

Democracy Way, Prosperity Park

Milnerton

Tel.: +27 (021) 5 51 25 77

Fax: +27 (021) 5 51 32 23

E-Mail: [email protected]

Bosch Headquarters

Midrand, Gauteng

Tel.: +27 (011) 6 51 96 00

Fax: +27 (011) 6 51 98 80

E-Mail: [email protected]

Disposal

The machine, accessories and packaging should

be sorted for environmental-friendly recycling.

Only for EC countries:

Do not dispose of power tools in-

to household waste!

According the European Guideline

2002/96/EC for Waste Electrical

and Electronic Equipment and its

implementation into national

right, power tools that are no longer usable

must be collected separately and disposed of in

an environmentally correct manner.

Subject to change without notice.

OBJ_BUCH-1067-001.book Page 23 Monday, September 28, 2009 8:35 AM

Page is loading ...

Français | 27

Bosch Power Tools 2 609 003 949 | (28.9.09)

Eléments de l’appareil

La numérotation des éléments de l’appareil se

réfère à la représentation de l’outil électroporta-

tif sur la page graphique.

1 Bouton de blocage de l’interrupteur

Marche/Arrêt

2 Interrupteur Marche/Arrêt

3 Tuyau d’aspiration*

4 Tubulure d’évacuation des poussières

5 Plaque de base

6 Commutateur pour dispositif de soufflerie

7 Guide-lame à rouleau

8 Lame de scie*

9 Voyant de contrôle pour le contrôle de tracé

«Cut Control»*

10 Socle pour le contrôle de tracé « Cut Con-

trol »*

11 Protège-mains

12 Poignée (surface de préhension isolante)

13 Porte-lame

14 Pare-éclats*

15 Guidage pour la butée parallèle

16 Fixation du guide-lame à rouleau

17 Vis

18 Echelle de graduation des angles de coupes

biaises

19 Butée parallèle avec dispositif pour coupes

circulaires*

20 Vis de blocage pour la butée parallèle*

21 Tige de centrage pour la butée parallèle*

22 Marquage de la coupe 0°

23 Marquage de la coupe 45°

*Les accessoires décrits ou illustrés ne sont pas tous

compris dans la fourniture. Vous trouverez les acces-

soires complets dans notre programme d’accessoi-

res.

Caractéristiques techniques

Scie sauteuse PST 700 E

N° d’article

3 603 CA0 0..

Variateur de vitesse

z

Puissance nominale

absorbée

W 500

Puissance utile débitée

W 300

Nombre de courses à

vide n

0

tr/min 500–3100

Amplitude de course

mm 20

Profondeur de coupe

max.

– dans le bois

– dans l’aluminium

– dans l’acier (non-

allié)

mm

70

10

4

Angle de coupe biaise

(gauche/droite) max.

°45

Poids suivant

EPTA-Procedure

01/2003

kg 1,6

Classe de protection

/II

Ces indications sont valables pour des tensions nomi-

nales de [U] 230/240 V. Ces indications peuvent varier

pour des tensions plus basses ainsi que pour des ver-

sions spécifiques à certains pays.

Respectez impérativement le numéro d’article se trou-

vant sur la plaque signalétique de l’outil électroportatif.

Les désignations commerciales des différents outils

électroportatifs peuvent varier.

OBJ_BUCH-1067-001.book Page 27 Monday, September 28, 2009 8:35 AM

Page is loading ...

30 | Français

2 609 003 949 | (28.9.09) Bosch Power Tools

Mise en marche

Modes opératoires

f Avant d’effectuer des travaux sur l’outil

électroportatif, retirez la fiche de la prise

de courant.

Réglage de l’angle pour coupes biaises

(voir figures D–E)

La plaque de base 5 peut s’orienter vers la droite

ou vers la gauche pour le réglage des angles de

coupe jusqu’à 45° dans le cas de coupes biaises.

Mettre une lame de scie 8 en place.

Le pare-éclats 14 ne peut pas être utilisé pour

les coupes biaises.

Desserrez la vis 17 et repoussez la plaque de

base 5 légèrement en direction de la tubulure

d’aspiration 4.

Pour le réglage des angles de coupes biaises avec

précision, la plaque de base dispose à gauche et à

droite de crans préréglés à 0°, 22,5° et 45°. Bas-

culez la plaque de base 5 suivant l’échelle de gra-

duation 18 dans la position souhaitée. D’autres

angles de coupes biaises peuvent être sélection-

nés à l’aide d’un rapporteur.

Repoussez ensuite la plaque de base 5 à fond en

direction de la lame de scie 8.

Déplacer la fixation 16 de sorte que le guide-la-

me à rouleau 7 repose sur le dos de la lame de

scie. Les coupes précises ne sont possible que

quand le guide-lame à rouleau repose bien sur le

dos de la lame de scie.

Resserrez la vis 17.

Contrôle du tracé pour coupes biaises

Pour le contrôle du tracé, un marquage 22 pour la

coupe rectangulaire de 0° et un marquage 23 pour

la coupe biaise vers la droite ou vers la gauche de

45°, conformément à la graduation 18, se trouvent

sur le voyant de contrôle pour le « Cut Control » 9.

Le marquage du tracé pour coupes biaises entre

0° et 45° est proportionnel. Il est possible de

l’appliquer sur le voyant de contrôle pour le

« Cut Control » 9 à l’aide d’un marqueur non-

permanent qui se laisse facilement enlever.

Pour effectuer des travaux avec précision, nous

recommandons d’effectuer une coupe d’essai.

Avancement de la plaque de base

(voir figure D)

Pour un sciage près du bord, il est possible de

reculer la plaque de base 5.

Mettre une lame de scie 8 en place.

Desserrez la vis 17 et repoussez la plaque de base

5 à fond en direction de la tubulure d’aspiration 4.

Déplacer la fixation 16 de sorte que le guide-la-

me à rouleau 7 repose sur le dos de la lame de

scie. Les coupes précises ne sont possible que

quand le guide-lame à rouleau repose bien sur le

dos de la lame de scie.

Resserrez la vis 17.

Lorsque la plaque de base 5 est déplacée, on ne

peut scier qu’avec un angle de coupe de 0°. En

outre, il ne faut pas utiliser le contrôle du tracé

« Cut Control » avec le socle 10, la butée paral-

lèle avec butée pour coupe circulaire 19 (acces-

soire) tout autant que le pare-éclats 14.

Dispositif de soufflerie

Grâce au débit d’air du dispositif de soufflerie 6

la ligne de coupe reste dégagée de tous copeaux.

45°

0°

45°

0°

45°

0°

22

,5°

45°

22 239105 18

Mettre le dispositif de soufflerie

en fonctionnement : Pour les

travaux dans le bois, les matiè-

res plastiques et autres maté-

riaux produisant un enlèvement

important de matière, tourner le

commutateur 6 dans la direction

de la tubulure d’aspiration.

Mettre le dispositif de soufflerie

hors fonctionnement : Pour les

travaux dans les métaux ainsi

que lorsque l’aspiration des

poussières est raccordée à un

dispositif d’aspiration, pousser

l’interrupteur 6 dans la direction

de la lame de scie.

OBJ_BUCH-1067-001.book Page 30 Monday, September 28, 2009 8:35 AM

Page is loading ...

Français | 33

Bosch Power Tools 2 609 003 949 | (28.9.09)

France

Vous êtes un utilisateur, contactez :

Le Service Clientèle Bosch Outillage Electro-

portatif

Tel. : 0 811 36 01 22

(coût d’une communication locale)

Fax : +33 (0) 1 49 45 47 67

E-Mail :

contact.outillage-electr[email protected]

Vous êtes un revendeur, contactez :

Robert Bosch (France) S.A.S.

Service Après-Vente Electroportatif

126, rue de Stalingrad

93705 DRANCY Cédex

Tel. : +33 (0) 1 43 11 90 06

Fax : +33 (0) 1 43 11 90 33

E-Mail :

[email protected]

Belgique, Luxembourg

Tel. : +32 (070) 22 55 65

Fax : +32 (070) 22 55 75

E-Mail : [email protected]

Suisse

Tel. : +41 (044) 8 47 15 12

Fax : +41 (044) 8 47 15 52

Elimination des déchets

Les outils électroportatifs, ainsi que leurs acces-

soires et emballages, doivent pouvoir suivre

chacun une voie de recyclage appropriée.

Seulement pour les pays de l’Union

Européenne :

Ne jetez pas votre appareil élec-

troportatif avec les ordures

ménagères !

Conformément à la directive euro-

péenne 2002/96/CE relative aux

déchets d’équipements électri-

ques et électroniques et sa mise

en vigueur conformément aux législations natio-

nales, les outils électroportatifs dont on ne peut

plus se servir doivent être isolés et suivre une

voie de recyclage appropriée.

Sous réserve de modifications.

OBJ_BUCH-1067-001.book Page 33 Monday, September 28, 2009 8:35 AM

Page is loading ...

38 | Español

2 609 003 949 | (28.9.09) Bosch Power Tools

Información sobre ruidos y vibraciones

Ruido determinado según EN 60745.

El nivel de presión sonora típico del aparato, de-

terminado con un filtro A, asciende a: Nivel de

presión sonora 88 dB(A); nivel de potencia

acústica 99 dB(A). Tolerancia K=3 dB.

¡Colocarse unos protectores auditivos!

Nivel total de vibraciones (suma vectorial de

tres direcciones) determinado según EN 60745:

Serrado de tabla de aglomerado de madera:

Valor de vibraciones generadas a

h

=10 m/s

2

,

Tolerancia K=3 m/s

2

,

Serrado de chapa de metal: Valor de vibraciones

generadas a

h

=11 m/s

2

, Tolerancia K=3 m/s

2

.

El nivel de vibraciones indicado en estas instruc-

ciones ha sido determinado según el procedi-

miento de medición fijado en la norma

EN 60745 y puede servir como base de compa-

ración con otras herramientas eléctricas. Tam-

bién es adecuado para estimar provisionalmen-

te la solicitación experimentada por las

vibraciones.

El nivel de vibraciones indicado ha sido determi-

nado para las aplicaciones principales de la he-

rramienta eléctrica. Por ello, el nivel de vibracio-

nes puede ser diferente si la herramienta

eléctrica se utiliza para otras aplicaciones, con

útiles diferentes, o si el mantenimiento de la

misma fuese deficiente. Ello puede suponer un

aumento drástico de la solicitación por vibracio-

nes durante el tiempo total de trabajo.

Para determinar con exactitud la solicitación ex-

perimentada por las vibraciones, es necesario

considerar también aquellos tiempos en los que

el aparato esté desconectado, o bien, esté en

funcionamiento, pero sin ser utilizado realmen-

te. Ello puede suponer una disminución drástica

de la solicitación por vibraciones durante el

tiempo total de trabajo.

Fije unas medidas de seguridad adicionales para

proteger al usuario de los efectos por vibracio-

nes, como por ejemplo: Mantenimiento de la he-

rramienta eléctrica y de los útiles, conservar ca-

lientes las manos, organización de las

secuencias de trabajo.

Declaración de conformidad

Declaramos bajo nuestra responsabilidad, que

el producto descrito bajo “Datos técnicos” está

en conformidad con las normas o documentos

normalizados siguientes: EN 60745 de acuerdo

con las regulaciones 2004/108/CE, 98/37/CE

(hasta el 28.12.2009), 2006/42/CE (a partir del

29.12.2009).

Expediente técnico en:

Robert Bosch GmbH, PT/ESC,

D-70745 Leinfelden-Echterdingen

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

Leinfelden, 02.09.2009

Montaje

f Antes de cualquier manipulación en la he-

rramienta eléctrica, sacar el enchufe de red

de la toma de corriente.

Montaje y cambio de la hoja de sierra

f Al montar la hoja de sierra utilice unos

guantes de protección. Podría accidentarse

en caso de tocar la hoja de sierra.

Selección de la hoja de sierra

Al final de estas instrucciones encontrará una

relación de las hojas de sierra recomendadas.

Solamente utilice hojas de sierra de una sola le-

va (vástago tipo T) o de vástago universal de

1/4" (vástago tipo U). La longitud de la hoja de

sierra no debe ser mayor que aquella precisada

para el corte.

Para efectuar cortes en curva de radio pequeño

emplear una hoja de sierra estrecha.

Dr. Egbert Schneider

Senior Vice President

Engineering

Dr. Eckerhard Strötgen

Head of Product

Certification

OBJ_BUCH-1067-001.book Page 38 Monday, September 28, 2009 8:35 AM

Page is loading ...

Bosch PST 700 E, PST 8000 PEL, PST700E, PST750PEL, PST750PELPST 8000 PELPST700E Owner's manual

Related papers

Other documents