Bosch GST 18 V-Li Specification

Category
Cordless jigsaws
Type
Specification

This manual is also suitable for

Robert Bosch GmbH
Power Tools Division
70745 Leinfelden-Echterdingen
Germany
www.bosch-pt.com
1 619 929 J70 (2011.09) T / 205 UNI
GST Professional
14,4 V-LI | 18 V-LI
de Originalbetriebsanleitung
en Original instructions
fr Notice originale
es Manual original
pt Manual original
it Istruzioni originali
nl Oorspronkelijke
gebruiksaanwijzing
da Original brugsanvisning
sv Bruksanvisning i original
no Original driftsinstruks
fi Alkuperäiset ohjeet
el Ðñùôüôõðï ïäçãéþí ÷ñÞóçò
tr Orijinal işletme talimat
pl Instrukcja oryginalna
cs Původní návod k používání
sk Pôvodný návod na použitie
hu Eredeti használati utasítás
ru Îðèãèíàëüíîå ðóêîâîäñòâî ïî
ýêñïëóàòàöèè
uk Îðèã³íàëüíà ³íñòðóêö³ÿ ç
åêñïëóàòàö³¿
ro Instrucţiuni originale
bg Îðèãèíàëíà èíñòðóêöèÿ
sr Originalno uputstvo za rad
sl Izvirna navodila
hr Originalne upute za rad
et Algupärane kasutusjuhend
lv Instrukcijas oriģinālvalodā
lt Originali instrukcija
ar
fa
ΕΎϤϴϠόΗϞϴϐθΘϟ΍ΔϴϠλϷ΍
̶Ϡλ΍ έΎ̯ ίήσ ̵ΎϤϨϫ΍έ
OBJ_BUCH-1257-002.book Page 1 Friday, September 23, 2011 11:38 AM
3 |
1 619 929 J70 | (23.9.11) Bosch Power Tools
GST 18 V-LI
Professional
1
3
13
12
2
5
8
9
10
11
7
6
4
14
OBJ_BUCH-1257-002.book Page 3 Friday, September 23, 2011 11:26 AM
1 619 929 J70 | (23.9.11) Bosch Power Tools
4 |
16 315
17
12
9
11
7
12
13
11
18
19
20
7
FE
DC
BA
OBJ_BUCH-1257-002.book Page 4 Friday, September 23, 2011 11:26 AM
5 |
1 619 929 J70 | (23.9.11) Bosch Power Tools
7
6
21
7
22
5
23
24 25
24 26
KJ
I
HG
OBJ_BUCH-1257-002.book Page 5 Friday, September 23, 2011 11:26 AM
English | 13
Bosch Power Tools 1 619 929 J70 | (23.9.11)
Akkus/Batterien:
Li-Ion:
Bitte beachten Sie die Hinweise im
Abschnitt „Transport“, Seite 12.
Änderungen vorbehalten.
English
Safety Notes
General Power Tool Safety Warnings
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
Work area safety
f Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
f Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
or fumes.
f Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
Electrical safety
f Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
f Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
f Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
f Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges and moving parts. Damaged
or entangled cords increase the risk of electric shock.
f When operating a power tool outdoors, use an exten-
sion cord suitable for outdoor use. Use of a cord suitable
for outdoor use reduces the risk of electric shock.
f If operating a power tool in a damp location is unavoid-
able, use a residual current device (RCD) protected
supply. Use of an RCD reduces the risk of electric shock.
Personal safety
f Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while op-
erating power tools may result in serious personal injury.
f Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
f Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising
power tools that have the switch on invites accidents.
f Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a ro-
tating part of the power tool may result in personal injury.
f Do not overreach. Keep proper footing and balance at
all times.
This enables better control of the power tool in
unexpected situations.
f Dress properly. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
f If devices are provided for the connection of dust ex-
traction and collection facilities, ensure these are con-
nected and properly used. Use of dust collection can re-
duce dust-related hazards.
Power tool use and care
f Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
f Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
f Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
f Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
f Maintain power tools. Check for misalignment or bind-
ing of moving parts, breakage of parts and any other
condition that may affect the power tool’s operation. If
damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
f Use the power tool, accessories and tool bits etc. in ac-
cordance with these instructions, taking into account
the working conditions and the work to be performed.
WARNING
OBJ_BUCH-1257-002.book Page 13 Friday, September 23, 2011 11:26 AM
14 | English
1 619 929 J70 | (23.9.11) Bosch Power Tools
Use of the power tool for operations different from those
intended could result in a hazardous situation.
Battery tool use and care
f Recharge only with the charger specified by the manu-
facturer. A charger that is suitable for one type of battery
pack may create a risk of fire when used with another bat-
tery pack.
f Use power tools only with specifically designated bat-
tery packs. Use of any other battery packs may create a
risk of injury and fire.
f When battery pack is not in use, keep it away from oth-
er metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
f Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally oc-
curs, flush with water. If liquid contacts eyes, addition-
ally seek medical help. Liquid ejected from the battery
may cause irritation or burns.
Service
f Have your power tool serviced by a qualified repair per-
son using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Safety Warnings for Jigsaws
f Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a “live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
f Keep hands away from the sawing range. Do not reach
under the workpiece. Contact with the saw blade can lead
to injuries.
f Apply the machine to the workpiece only when
switched on. Otherwise there is danger of kickback when
the cutting tool jams in the workpiece.
f Pay attention that the base plate 7 rests securely on
the material while sawing. A jammed saw blade can
break or lead to kickback.
f When the cut is completed, switch off the machine and
then pull the saw blade out of the cut only after it has
come to a standstill. In this manner you can avoid kick-
back and can place down the machine securely.
f Use only undamaged saw blades that are in perfect con-
dition. Bent or dull saw blades can break, negatively influ-
ence the cut, or lead to kickback.
f Do not brake the saw blade to a stop by applying side
pressure after switching off. The saw blade can be dam-
aged, break or cause kickback.
f Use appropriate detectors to determine if utility lines
are hidden in the work area or call the local utility compa-
ny for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage.
f Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
f Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
f Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e.g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
f In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and seek
medical help in case of complaints. The vapours can irri-
tate the respiratory system.
f Use the battery only in conjunction with your Bosch
power tool. This measure alone protects the battery
against dangerous overload.
f Use only original Bosch batteries with the voltage
listed on the nameplate of your power tool. When using
other batteries, e.g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries.
Product Description and
Specifications
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The machine is intended for making separating cuts and cut-
outs in wood, plastic, metal, ceramic plates and rubber while
resting firmly on the workpiece. It is suitable for straight and
curved cuts with mitre angles to 45°. The saw blade recom-
mendations are to be observed.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Lock-off button for On/Off switch
2 On/Off switch
3 Battery*
4 Battery unlocking button
5 Allen key
6 Plastic guide plate
7 Base plate
8 Adjusting lever for orbital action
9 Guide roller
10 Lead for the parallel guide
11 Saw blade*
12 SDS clamping lever for saw blade release
13 Contact protector
OBJ_BUCH-1257-002.book Page 14 Friday, September 23, 2011 11:26 AM
English | 15
Bosch Power Tools 1 619 929 J70 | (23.9.11)
14 Handle (insulated gripping surface)
15 Button for charge-control indicator*
16 Battery charge-control indicator*
17 Stroke rod
18 Vacuum connection*
19 Vacuum hose*
20 Splinter guard
21 Steel sliding shoe*
22 Screw
23 Scale for mitre angle
24 Locking screw for parallel guide*
25 Parallel guide with circle cutter*
26 Centring tip of the circle cutter*
*Accessories shown or described are not part of the standard
delivery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Noise/Vibration Information
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 19.09.2011
Assembly
f Before any work on the machine itself (e.g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
Cordless Jigsaw GST 14,4 V-LI
Professional
GST 18 V-LI
Professional
Article number
3 601 E8J 4.. 3 601 E8J 3..
Rated voltage
V= 14.4 18
Stroke rate at no load
n
0
min
-
1
0–2500 0–2700
Stroke
mm 23 23
Cutting capacity, max.
in wood
in aluminium
in non-alloy steel
mm
mm
mm
90
20
8
90
20
8
Bevel cuts
(left/right), max.
°4545
Weight according to
EPTA-Procedure
01/2003
kg 2.3 2.4
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
Please observe that when using “Compact” Bosch batteries with re-
duced capacity, the performance of your power tool is also reduced.
GST 14,4 V-LI
Professional
GST 18 V-LI
Professional
Measured sound values determined
according to EN 60745.
Typically the A-weighted noise levels
of the product are
Sound pressure level
Sound power level
Uncertainty K=
Wear hearing protection!
dB(A)
dB(A)
dB
80
91
3
81
92
3
Vibration total values a
h
(triax vector
sum) and uncertainty K determined
according to EN 60745:
Cutting board:
a
h
K
Cutting sheet metal:
a
h
K
m/s
2
m/s
2
m/s
2
m/s
2
5.5
1.5
6.5
1.5
6
1.5
8.5
1.5
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Engineering Director
PT/ESI
GST 14,4 V-LI
Professional
GST 18 V-LI
Professional
OBJ_BUCH-1257-002.book Page 15 Friday, September 23, 2011 11:26 AM
16 | English
1 619 929 J70 | (23.9.11) Bosch Power Tools
Battery Charging
f Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Do not continue to press the On/Off
switch after the machine has been au-
tomatically switched off. The battery can be damaged.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Observe the notes for disposal.
Removing the Battery
The battery 3 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery un-
locking button 4 unintentionally. As long as the battery is insert-
ed in the power tool, it is held in position by means of a spring.
To remove the battery 3, press the battery unlocking button 4
and pull the battery toward the rear out of the power tool. Do
not exert any force when doing this.
Battery Charge-control Indication
(only for 3.0 Ah battery) (see figure A)
The three green LEDs of the battery charge-control indicator
16 indicate the charge condition of the battery 3. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
Press button 15 to indicate the charge condition. This is also
possible when the battery 3 is removed.
When no LED lights up after pushing button 15, then the bat-
tery is defective and must be replaced.
Replacing/Inserting the Saw Blade
f When mounting the saw blade, wear protective gloves.
Danger of injury when touching the saw blade.
Selecting a Saw Blade
An overview of recommended saw blades can be found at the
end of these instructions. Use only T-shank saw blades. The saw
blade should not be longer than required for the intended cut.
Use a thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure B)
f Clean the shank of the saw blade before inserting it. An
unclean shank cannot be fastened securely.
Insert the saw blade 11 into the stroke rod 17 until it latches.
The SDS lever 12 automatically snaps to the rear and the saw
blade is locked. Do not manually press the lever 12 toward
the rear, otherwise you could damage the machine.
While inserting the saw blade, pay attention that the back of
the saw blade is positioned in the groove of the guide roller 9.
f Check the tight seating of the saw blade. A loose saw
blade can fall out and lead to injuries.
Ejecting the Saw Blade (see figure C)
f When ejecting the saw blade, hold the machine in such
a manner that no persons or animals can be injured by
the ejected saw blade.
Turn the SDS lever 12 forward towards the contact protector
13 to the stop. The saw blade is released and ejected.
Dust/Chip Extraction
f Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
As far as possible, use a dust extraction system suitable
for the material.
Provide for good ventilation of the working place.
It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
f Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Connecting the Dust Extraction (see figures DE)
Insert the vacuum connection 18 into the opening of base
plate 7.
Place a vacuum hose 19 (accessory) onto the vacuum connec-
tion 18. Connect the vacuum hose 19 with a vacuum cleaner
(accessory). An overview for the connection of various vacuum
cleaners can be found at the end of these instructions.
To enable optimum dust extraction, use the splinter guard 20
if possible.
The vacuum cleaner must be suitable for the material being
worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special vacuum cleaner.
Splinter Guard (see figure F)
The splinter guard 20 can prevent fraying of the surface while
sawing wood. The splinter guard can only be used with certain
saw blade types, and only at a cutting angle of 0°. When saw-
ing with the splinter guard, the base plate 7 may not be offset
to the rear for sawing close to edges.
Insert the splinter guard 20 into base plate 7 from the front.
LED Capacity
Continuous lighting 3 x green
2/3
Continuous lighting 2 x green
1/3
Continuous lighting 1 x green
<1/3
Flashing light 1 x green
Reserve
WARNING
OBJ_BUCH-1257-002.book Page 16 Friday, September 23, 2011 11:26 AM
English | 17
Bosch Power Tools 1 619 929 J70 | (23.9.11)
Sliding Shoe (see figure G)
The plastic guide plate 6 of base plate 7 reduces sensitive sur-
faces from being scratched up. When cutting metal, use the
steel sliding shoe 21.
To mount the steel sliding shoe 21, slide it onto base plate 7
from the front.
Operation
Operating Modes
f Before any work on the machine itself (e.g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
Orbital Action Settings
The four orbital action settings allow for optimal adaptation of
cutting speed, cutting capacity and cutting pattern to the ma-
terial being sawed.
The orbital action can be adjusted with the adjusting lever 8,
even during operation.
The optimal orbital action setting for the respective applica-
tion can be determined through practical testing. The follow-
ing recommendations apply:
Select a lower orbital action setting (or switch it off) for a fin-
er and cleaner cutting edge.
For thin materials such as sheet metal, switch the orbital
action off.
For hard materials such as steel, work with low orbital action.
For soft materials and when sawing in the direction of the
grain, work with maximum orbital action.
Adjusting the Cutting Angle (see figure H)
The base plate 7 can be swivelled by 45° to the left or right for
mitre cuts.
Remove the vacuum connection 18.
Loosen screw 22 with Allen key 5 and slide the base plate 7 in
toward the battery 3 to the stop.
For adjustment of precise mitre angles, the base plate has ad-
justment notches on the left and right at 0° and 45°. Swivel
the base plate 7 to the desired position according to the scale
23. Other mitre angles can be adjusted using a protractor.
Afterwards, push the base plate 7 to the stop in the direction
of the saw blade 11.
Tighten the screw 22 again.
The vacuum connection 18 and the splinter guard 20 cannot
be used for bevel cuts.
Offsetting the Base Plate (see figure H)
For sawing close to edges, the base plate 7 can be offset to
the rear.
Loosen screw 22 with Allen key 5 and slide the base plate 7 in
toward the battery 3 to the stop.
Tighten the screw 22 again.
When sawing with the base plate 7 offset, the parallel guide
with circle cutter 25 as well as the splinter guard 20 may not
be used.
Starting Operation
Inserting the Battery
f Use only original Bosch lithium ion batteries with the
voltage listed on the nameplate of your power tool. Using
other batteries can lead to injuries and pose a fire hazard.
Insert the charged battery 3 from the rear into the base of the
power tool. Press the battery completely into the base until
the red stripe can no longer be seen and the battery is secure-
ly locked.
Switching On and Off
To start the machine, firstly press on the safety switch 1 next
to the symbol to deactivate it. Then press and hold the
On/Off switch 2.
To switch off the machine, release the On/Off switch 2. Acti-
vate the safety switch 1 by pressing on it next to the
symbol .
Note: For safety reasons, the On/Off switch 2 cannot be
locked; it must remain pressed during the entire operation.
Controlling the Stroke Rate
Increasing or reducing the pressure on the On/Off switch 2
enables stepless stroke-rate control of the switched-on ma-
chine.
Light pressure on the On/Off switch 2 results in a low stroke
rate. Increasing the pressure also increases the stroke rate.
The required stroke rate is dependent on the material and the
working conditions and can be determined by a practical trial.
Reducing the stroke rate is recommended when the saw
blade engages in the material as well as when sawing plastic
and aluminium.
After longer periods of work at low stroke rate, the machine
can heat up considerably. Remove the saw blade from the ma-
chine and allow the machine to cool down by running it for ap-
prox. 3 minutes at maximum stroke rate.
Temperature Dependent Overload Protection
When using the machine as intended for, it cannot be subject
to overload. In case of excessive load or when not within the
permitted battery temperature range of 070 °C, the speed
is reduced or the machine switches off. With reduced speed,
the machine will not run at full speed again until after reaching
the permitted battery temperature or when the load is re-
duced. In case of automatic shut-off, switch the machine off,
allow the battery to cool down and then switch the machine
on again.
Protection Against Deep Discharging
The lithium-ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
No orbital action
Small orbital action
Medium orbital action
Large orbital action
OBJ_BUCH-1257-002.book Page 17 Friday, September 23, 2011 11:26 AM
18 | English
1 619 929 J70 | (23.9.11) Bosch Power Tools
Working Advice
f When sawing small or thin workpieces, always use a
firm support.
Contact Protector
The contact protector 13 attached to the casing prevents ac-
cidental touching of the saw blade during the working proce-
dure and may not be removed.
Plunge Cutting (see figure I)
f Plunge cuts may only be applied to soft materials, such
as wood, gypsum plaster boards, etc.!
Use only short saw blades for plunge cutting. Plunge cutting is
possible only with the mitre angle set at 0°.
Place the machine with the front edge of the base plate 7 on
to the workpiece without the saw blade 11 touching the work-
piece and switch on. For machines with stroke rate control,
select the maximum stroke rate. Firmly hold the machine
against the workpiece and by tilting the machine, slowly
plunge the saw blade into the workpiece.
When the base plate 7 fully lays on the workpiece, continue
sawing along the desired cutting line.
Parallel Guide with Circle Cutter (Accessory)
Parallel Cuts (see figure J): Loosen the locking screw 24 and
slide the scale of the parallel guide through the lead 10 in
the base plate. Set the desired cutting width as the scale
value on the inside edge of the base plate. Tighten the locking
screw 24.
Circular Cuts (see figure K): Set the locking screw 24 to the
other side of the parallel guide. Slide the scale of the parallel
guide through the lead 10 in the base plate. Drill a hole in the
workpiece centred in the section to be sawn. Insert the cen-
tring tip 26 through the inside opening of the parallel guide
and into the drilled hole. Set the radius as the scale value
on the inside edge of the base plate. Tighten the locking
screw 24.
Coolant/Lubricant
When sawing metal, coolant/lubricant should be applied
alongside cutting line because of the material heating up.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the machine itself (e.g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
f For safe and proper working, always keep the machine
and ventilation slots clean.
Clean the saw blade holder regularly. For this, remove the saw
blade from the machine and lightly tap out the machine on a
level surface.
Heavy contamination of the machine can lead to malfunc-
tions. Therefore, do not saw materials that produce a lot of
dust from below or overhead.
Lubricate the guide roller 9 occasionally with a drop of oil.
Check the guide roller 9 regularly. If worn, it must be replaced
through an authorised Bosch after-sales service agent.
The plastic guide plate 6 should be replaced when worn.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
After-sales Service and Customer Assistance
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Our customer service representatives can answer your ques-
tions concerning possible applications and adjustment of
products and accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: +61 (01300) 307 044
Fax: +61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
OBJ_BUCH-1257-002.book Page 18 Friday, September 23, 2011 11:26 AM
English | 19
Bosch Power Tools 1 619 929 J70 | (23.9.11)
Republic of South Africa
Customer service
Hotline: +27 (011) 6 51 96 00
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: +27 (011) 4 93 93 75
Fax: +27 (011) 4 93 01 26
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: +27 (031) 7 01 21 20
Fax: +27 (031) 7 01 24 46
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: +27 (021) 5 51 25 77
Fax: +27 (021) 5 51 32 23
Bosch Headquarters
Midrand, Gauteng
Tel.: +27 (011) 6 51 96 00
Fax: +27 (011) 6 51 98 80
People’s Republic of China
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Service Hotline: 400 826 8484
Fax: +86 571 8777 4502
www.bosch-pt.com.cn
HK and Macau Special Administrative Regions
Robert Bosch Hong Kong Co. Ltd.
21st Floor, 625 King’s Road
North Point, Hong Kong
Customer Service Hotline: +852 2101 0235
Fax: +852 2590 9762
www.bosch-pt.com.hk
Indonesia
PT. Multi Mayaka
Kawasan Industri Pulogadung
Jalan Rawa Gelam III No. 2
Jakarta 13930
Indonesia
Tel.: +62 (21) 46 83 25 22
Fax: +62 (21) 46 82 86 45/68 23
www.bosch-pt.co.id
Philippines
Robert Bosch, Inc.
28th Floor Fort Legend Towers,
3rd Avenue corner 31st Street,
Fort Bonifacio Global City,
1634 Taguig City, Philippines
Tel.: +63 (2) 870 3871
Fax: +63 (2) 870 3870
www.bosch-pt.com.ph
Bosch Service Center:
9725-27 Kamagong Street
San Antonio Village
Makati City, Philippines
Tel.: +63 (2) 899 9091
Fax: +63 (2) 897 6432
Malaysia
Robert Bosch (S.E.A.) Pte. Ltd.
No. 8A, Jalan 13/6
G.P.O. Box 10818
46200 Petaling Jaya
Selangor, Malaysia
Tel.: +60 (3) 7966 3194
Fax: +60 (3) 7958 3838
Toll-Free: 1800 880 188
www.bosch-pt.com.my
Thailand
Robert Bosch Ltd.
Liberty Square Building
No. 287, 11 Floor
Silom Road, Bangrak
Bangkok 10500
Tel.: +66 (2) 6 31 18 79 – 18 88 (10 lines)
Fax: +66 (2) 2 38 47 83
Robert Bosch Ltd., P. O. Box 2054
Bangkok 10501, Thailand
Bosch Service – Training Centre
2869-2869/1 Soi Ban Kluay
Rama IV Road (near old Paknam Railway)
Prakanong District
10110 Bangkok
Thailand
Tel.: +66 (2) 6 71 78 00 – 4
Fax: +66 (2) 2 49 42 96
Fax: +66 (2) 2 49 52 99
Singapore
Robert Bosch (SEA) Pte. Ltd.
11 Bishan Street 21
Singapore 573943
Tel.: +65 6571 2772
Fax: +65 6350 5315
Toll-Free: 1800 333 8333
www.bosch-pt.com.sg
OBJ_BUCH-1257-002.book Page 19 Friday, September 23, 2011 11:26 AM
20 | Français
1 619 929 J70 | (23.9.11) Bosch Power Tools
Vietnam
Robert Bosch Vietnam Co. Ltd
10/F, 194 Golden Building
473 Dien Bien Phu Street
Ward 25, Binh Thanh District
84 Ho Chi Minh City
Vietnam
Tel.: +84 (8) 6258 3690 ext. 413
Fax: +84 (8) 6258 3692
www.bosch-pt.com
Transport
The contained lithium-ion batteries are subject to the Danger-
ous Goods Legislation requirements. The user can transport
the batteries by road without further requirements.
When being transported by third parties (e.g.: air transport or
forwarding agency), special requirements on packaging and
labelling must be observed. For preparation of the item being
shipped, consulting an expert for hazardous material is re-
quired.
Dispatch batteries only when the housing is undamaged.
Tape or mask off open contacts and pack up the battery in
such a manner that it cannot move around in the packaging.
Please also observe possibly more detailed national regula-
tions.
Disposal
The machine, rechargeable batteries, accessories
and packaging should be sorted for environmental-
friendly recycling.
Do not dispose of power tools and batteries/rechargeable
batteries into household waste!
Only for EC countries:
According to the European Guideline
2002/96/EC, power tools that are no long-
er usable, and according to the European
Guideline 2006/66/EC, defective or used
battery packs/batteries, must be collected
separately and disposed of in an environ-
mentally correct manner.
Batteries no longer suitable for use can be directly returned at:
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
Battery packs/batteries:
Li-ion:
Please observe the instructions in sec-
tion “Transport”, page 20.
Subject to change without notice.
Français
Avertissements de sécurité
Avertissements de sécurité généraux pour l’outil
Lire tous les avertissements
de sécurité et toutes les ins-
tructions. Ne pas suivre les avertissements et instructions
peut donner lieu à un choc électrique, un incendie et/ou une
blessure sérieuse.
Conserver tous les avertissements et toutes les instruc-
tions pour pouvoir s’y reporter ultérieurement.
Le terme « outil » dans les avertissements fait référence à
votre outil électrique alimenté par le secteur (avec cordon
d’alimentation) ou votre outil fonctionnant sur batterie (sans
cordon d’alimentation).
Sécurité de la zone de travail
f Conserver la zone de travail propre et bien éclairée. Les
zones en désordre ou sombres sont propices aux accidents.
f Ne pas faire fonctionner les outils électriques en at-
mosphère explosive, par exemple en présence de liqui-
des inflammables, de gaz ou de poussières. Les outils
électriques produisent des étincelles qui peuvent enflam-
mer les poussières ou les fumées.
f Maintenir les enfants et les personnes présentes à
l’écart pendant l’utilisation de l’outil. Les distractions
peuvent vous faire perdre le contrôle de l’outil.
Sécurité électrique
f Il faut que les fiches de l’outil électrique soient adaptées
au socle. Ne jamais modifier la fiche de quelque façon
que ce soit. Ne pas utiliser d’adaptateurs avec des outils
à branchement de terre. Des fiches non modifiées et des
socles adaptés réduiront le risque de choc électrique.
f Eviter tout contact du corps avec des surfaces reliées à
la terre telles que les tuyaux, les radiateurs, les cuisi-
nières et les réfrigérateurs. Il existe un risque accru de
choc électrique si votre corps est relié à la terre.
f Ne pas exposer les outils à la pluie ou à des conditions
humides. La pénétration d’eau à l’intérieur d’un outil aug-
mentera le risque de choc électrique.
f Ne pas maltraiter le cordon. Ne jamais utiliser le cordon
pour porter, tirer ou débrancher l’outil. Maintenir le
cordon à l’écart de la chaleur, du lubrifiant, des arêtes
ou des parties en mouvement. Les cordons endommagés
ou emmêlés augmentent le risque de choc électrique.
AVERTISSEMENT
OBJ_BUCH-1257-002.book Page 20 Friday, September 23, 2011 11:26 AM
| 203
Bosch Power Tools 1 619 929 J70 | (23.9.11)
T 144 D
T 244 D
T 144 DP
T 101 B
T 308 B
T 308 BF
T 101 BIF
T 118 B
T 123 X
T 127 D
T 345 XF
OBJ_BUCH-1257-002.book Page 203 Friday, September 23, 2011 11:37 AM
1 619 929 J70 | (23.9.11) Bosch Power Tools
204 |
GAS 25
GAS 50
GAS 50 M
Ø 19 mm
2 607 002 161 (3 m)
2 607 002 162 (5 m)
2 608 438 692
(L-BOXX 136)
2 608 438 027
2 605 510 301
2 601 016 096
2 601 098 123
2 608 040 289
18 V (Li-Ion)
2 607 336 170 (1,3 Ah „compact“)
2 607 336 092 (2,6 Ah)
2 607 336 236 (3,0 Ah)
AL 1860 CV
(14,4/18 V)
2 607 225 322 (EU)
2 607 225 324 (UK)
AL 1820 CV
(14,4/18 V)
2 607 225 424 (EU)
2 607 225 426 (UK)
14,4 V (Li-Ion)
2 607 336 150 (1,3 Ah „compact“)
2 607 336 078 (2,6 Ah)
2 607 336 224 (3,0 Ah)
OBJ_BUCH-1257-002.book Page 204 Friday, September 23, 2011 11:37 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204

Bosch GST 18 V-Li Specification

Category
Cordless jigsaws
Type
Specification
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI