Agri-Fab 24206 Owner's manual

Agri-Fab
Brand
Agri-Fab
Model
24206
Type
Owner's manual

This manual is also suitable for

DISC CULTIVATOR
(SLEEVE HITCH)
the fastest way to purchase parts
www.speedepart.com
™
OWNERS MANUAL
MANUAL DEL USUARIO
NOTICE D’UTILISATION
Model No.
Modelo No.
Modèle No.
45-02662
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
ATTENTION:
Lire et suivre attentivement
les instructions et consignes
de sécurité de cette notice.
PRECAUCION:
Lea cuidadosamente
los Procedimientos e
Instrucciones para la
Operación Segura de la
Máquina.
• Safety
• Assembly
• Operation
• Maintenance
• Parts
• Seguridad
• Montaje
• Operación
• Mantenimiento
• PiezasdeRepuesto
• Sécurité
• Assemblage
• Fonctionnement
• Maintenance
• PiècesdeRechange
CULTIVATEUR À DISQUES
(CHAPE D’ATTELAGE)
ARADO CULTIVADOR A DISCO
(ENGANCHE TIPO CAMISA)
PRINTEDINU.S.A. FORMNO.40107rev,(8/9/10)
Page is loading ...
3
REF. QTY. DESCRIPTION
A 1 HexBolt,1/2"x1-1/2"Lg.
B 4 CarriageBolt,1/2"x1-1/2"
C 4 CarriageBolt,3/8"x1"Lg.
D 4 NylockNut,3/8"
E 5 NylockNut,1/2"
REF. QTY. DESCRIPTION
F 4 HexNut,3/4"
G 16 FlatWasher,3/4"
H 2 Bearing Sleeve
I 4 Spacer
REF. CTD DESCRIPCIÓN
A 1 Pernodecabezahexagonalde1/2"x1-1/2" Lg.
B 4 Pernodecarroceríade1/2"x1-1/2"Lg.
C 4 PernodeCarroceríade3/8"x1"Lg.
D 4 Tuercahexagonalde3/8"
E 5 Tuercahexagonaldecierrede1/2"
REF. CTD DESCRIPCIÓN
F 4 Tuercahexagonalde3/4"
 G 16 Arandelaplanade3/4"
H 2 CamisadelCojinete
I 4 Espaciador
RÉF. QTÉ DESCRIPTION
A 1 BoulonsHexagonaux,1/2"x1-1/2"Grands
B 4 Boulonsdecarrosserie,1/2"x1-1/2"
C 4 Boulonsdecarrosserie,3/8"x1"Grands
D 4 ÉcrousHexagonaux,3/8"
E 5 Contre-écrousHexagonaux,1/2"
RÉF. QTÉ DESCRIPTION
F 4 ÉcrousHexagonaux,3/4"
 G 16 RondellesPlates,3/4"
H 2 Chemised’arbresouscoussinet
I 4 Entretoise
HARDWARE CHART - CONTENTS SHOWN ACTUAL SIZE
HERRAJES – PIEZAS MOSTRADAS A TAMAÑO REAL
GRAPHIQUE DE QUINCAILLERIE – PIÈCES EN TAILLE RÉELLE
A B C
D
E
F
G
I
H
4
Anypowerequipmentcancauseinjuryifoperatedimproperlyoriftheuserdoesnotunderstandhowtooperatetheequipment.
Exercisecautionatalltimes,whenusingpowerequipment.
SAFETY RULES
Lookforthissymboltopointoutimportantsafetyprecautions.Itmeans–Attention!!
Become alert!! Your safety is involved.
1. Readthisownersmanualandyourvehicleandsleeve
hitchownersmanualsbeforeusingthisequipment.
2. Do not allow children to operate vehicle or disc
cultivator.
3. Donotallowadultstooperatevehicleordisccultivator
withoutproperinstructions.
4. Donotallowanyonetorideonthedisccultivator.
5. Before lowering and operating the disc cultivator, be
surenooneisneartheareaofoperation.
6. Lowerdisccultivatorwhenleavingvehicleunattended.
7. Wearsubstantialfootwearwhenusingdisccultivator.
Thediscedgesaresharp!
8. Vehiclebrakingandstabilitymaybeaffectedwiththe
attachmentofthisequipment.Driveslowlywhendisc
cultivator is in transport position. Stay off of steep
slopes.
9. Stopandinspectfordamageafterstrikinganobject.
Repairanydamagebeforecontinuingoperation.
10.Keep all nuts and bolts tight and be sure that the
equipment is in safe operating condition.
11.Locktractorlifthandleindownpositionwhenattaching
orremovingdisccultivatorfromsleevehitch.
ENGLISH
5
FIGURE 2
TOOLS REQUIRED FOR ASSEMBLY
(2) 9/16"Wrenches
(2) 3/4"Wrenches
(2) 1-1/8"Wrenchesor10"AdjustableWrenches
(1) GreaseGun
CAUTION: Discbladeshavesharpedges.Use
careinhandlingandassembly.Weargloves for
extra protection against cuts.
Removeloosepartsandhardwarepackagefromthecarton.
Layoutandidentifyasshownonpages2and3.
1. Assemblefour discs to each bearing hangerbracket
usingabearingsleeve(unplated),a3/4"x16"hexbolt,
eight3/4"atwashers,twospacersandtwo3/4"hex
nuts.Besurethediscsfacethesamedirectionrelative
tothehangerbracketasshowninthegure1.Tighten
thersthexnutandthentightenthesecondhexnut
againsttherst.
2. Lubricatethebearingsthroughthegreasettingsinthe
bearinghangerbracketassembliesuntilgreaseisforced
outthroughthebearings.
FIGURE 1
1/2" x 1-1/2"
CARRIAGE BOLT
1/2" NYLOCK NUT
DRAW BAR
HITCH BRACKET
3. Assemblethehitchbrackettothedrawbarusingtwo
1/2"x1-1/2"carriageboltsand1/2"nylocknuts.See
gure2.
4. Position the tray with the slots angled either toward
rearcenterorfrontcenterasshowningure3.(Refer
to Operation section on page 6 for more information.)
Assemblethedrawbartothebottomofthetrayusing
two1/2"x1-1/2"carriageboltsand1/2"nylocknuts.
Seegure3.
FIGURE 3
SPACER
BEARING SLEEVE
3/4" x 16"
HEX BOLT
DISC BLADE
3/4" HEX NUTS
3/4" FLAT WASHER
BEARING HANGER
BRACKET
SPACER
ASSEMBLY INSTRUCTIONS
ENGLISH
1/2" x 1-1/2"
CARRIAGE BOLT
1/2" NYLOCK NUT
THROWS SOIL
TO INSIDE
THROWS SOIL
TO OUTSIDE
6
ASSEMBLY OF SINGLE CULTIVATOR
Thefollowinginstructionsdescribethetwotypesofdisc
arrangement.Thediscscanalsobemountedfartherapart
byusingtheouterslotsinthetray.
5. Assemblethediscassembliestothetrayusingfour3/8"
x1"carriageboltsand3/8"nylocknuts.Swivelthedisc
assembliessothatthecarriageboltiscenteredinthe
angleadjustmentslot.Tighten. Thisplacesthediscs
atthestandard15degreeangle.Seegures4and5.
ASSEMBLY OF TANDEM CULTIVATORS
(Requirespurchaseofasecondcultivator.)
Thefrontcultivatorshouldbeassembledasshowningure
4.Therearcultivatorshouldbeassembledusingthefollowing
instructions.Notethatthepositionofthetrayanddrawbar
arethereverseofthefrontcultivator.
6. Assemblethediscassembliestotheouterslotsinthe
trayusingfour3/8"x1"carriageboltsand3/8"nylock
nuts.Swivelthediscassembliessothatthecarriagebolt
iscenteredintheangleadjustmentslot.Thisplacesthe
discsatthestandard15degreeangle.Tighten. See
gure6.
FIGURE 6
FIGURE 5
3/8" x 1"
CARRIAGE BOLT
ANGLE
ADJUSTMENT
SLOT
3/8" NYLOCK NUT
CONCAVE (DISHED) SIDE OF DISC FACES OUTWARD.
CONCAVE (DISHED) SIDE OF DISC FACES INWARD.
FIGURE 4
CONCAVE (DISHED) SIDE OF DISC FACES INWARD.
ENGLISH
3/8" x 1"
CARRIAGE BOLT
3/8" NYLOCK NUT
ANGLE
ADJUSTMENT
SLOT
3/8" x 1"
CARRIAGE BOLT
ANGLE
ADJUSTMENT
SLOT
3/8" NYLOCK NUT
THIS END
AT FRONT
7
CAUTION:Locktractorlifthandleindownposition
when attaching or removing the disc cultivator
fromsleevehitch.
ATTACHING CULTIVATOR TO TRACTOR
Refertoyoursleevehitchownersmanual.
1. Removethestabilizerboltsfromthetractor’ssleevehitch
asshowningure7toallowsidetosidemotionofthe
diskcultivator.
2. Attach the disc cultivatorto thesleeve hitch on your
tractorusingthesleevehitchpin.
4. Adjustthesleevehitchsothatthedisccultivatorisfree
tolowerbelowgroundlevelbutcanstillberaisedan
adequatedistanceabovegroundfortransport.
OPERATION
1. Checkforlooseboltsaftereachuse.
2. Cleanthedisksandlightlyoilanyexposedmetalafter
eachuse.
3. Removealldirtandrustandtouchupwithpaintbefore
storing.
4. Storeinsideadryarea.
Thedisccultivatorisusedtobreakupclodsofdirtinplowed
soil.Itcanalsobeusedtocultivatebetweenrowsofyoung
plants.
1. Before starting make sure the soil is dry enough by
squeezing some in your hand. If it forms a ball that
doesn’tcrumblethenthesoilistoowetfordiscing.Wet
soilwillpackbetweenthediscblades.
2. Adjustthediscstothedesiredanglesetting.Theangle
canbevariedfrom10to20degrees.Startwithasetting
of15degrees(thecarriageboltcenteredintheangle
adjustment slot in the bearing hanger bracket). The
greatertheangle,thegreaterthediscingaction.
3. Tobreakupdirtclodsinplowedsoil,startdiscingslowly
atrst.Astheclodsarebrokenupthespeedmaybe
gradually increased. Disc the soil using a crisscross
patternforbestresults.
4. Tocultivateyoungcropsbystraddlingtherows,move
thediscstothemaximumwidthsetting.Tothrowthe
dirttotheoutside,theconcavesideofthediscsshould
faceoutwardwiththediscassembliesangledtoward
therearcenter.Tothrowdirttotheinside,tosmother
youngweedsinthecroprow,theconcavesideofthe
discsshouldfaceinwardwiththediscassembliesangled
towardthefrontcenter.
5. Tousetwocultivatorsintandem,thediscassemblies
shouldbepositionedasshowningure8,withtheinside
discsalmosttouchingonthefrontcultivatorand8"to
10"apartontherearcultivator.Withthisarrangement
thefrontcultivatorwillthrowthedirttotheoutsideand
therearcultivatorwillthrowthedirtbacktotheinside.
6. Upto100lbs.ofweightmaybeaddedtohelpincrease
penetration.Concreteblocksorotherweightmaybetied
orstrappedtothecultivatortray.Beforeaddingweight,
thecultivatorshouldbeattachedtothetractorwiththe
sleevehitchinthedownposition.
MAINTENANCE
FIGURE 8
CAUTION: Donot attempt toraisethe tractor
sleevehitchwhenconnectedtodisccultivators
in tandem arrangement.
ATTACHING TANDEM CULTIVATORS
1. Attachthefrontcultivatorasinstructedabove.
2. Attachtherearcultivatortothefrontcultivatorbyfastening
thereardrawbarstogetherusinga1/2"x1-1/2"hexbolt
anda 1/2" nylock nut.Do not completely tighten the
nut,allowingaslightamountofplaybetweentherear
drawbars.Seegure8.
FIGURE 7
STABILIZER BOLTS
(REMOVE)
TRACTOR SLEEVE HITCH
1/2" x 1-1/2"
HEX BOLT
1/2" NYLOCK
NUT
8"-10"
ENGLISH
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
REPAIR PARTS FOR MODEL 45-02662 - DISC CULTIVATOR
REF. PART QTY. DESCRIPTION
NO. NO.
10 46859 4 Spacer,3/4"I.D.x4-1/4"Lg.
11 1540-162 16 FlatWasher,3/4"Std.Wrt.
12 46860 4 HexNut,3/4-10Thread
13 43350 4 CarriageBolt,3/8-16x1"Lg.
14 HA21362 4 NylockNut,3/8-16Thread
15 47660 4 CarriageBolt,1/2-13x1-1/2"Lg.
16 43020 1 HexBolt,1/2-13x1-1/2"Lg.
17 712-3083 5 NylockNut,1/2-13Thread
40107 1 OwnersManual
REF. PART QTY. DESCRIPTION
NO. NO.
1 24850 1 DrawBar
2 24851 1 HitchBracket
3 24852 1 Tray
4 40106 8 NotchedBladeDisc
5 63510 2 BearingHangerBrkt.Assembly
6 44488 4 Bearing(Includedin#63510)
7 46858 2 GreaseFitting(Includedin#63510)
8 46857 2 HexBolt,3/4-10x16"Lg.
9 24240 2 BearingSleeve
the fastest way to purchase parts
www.speedepart.com
REPAIR PARTS
Agri-Fab,Inc.
809SouthHamilton
Sullivan,IL.61951
217-728-8388
www.agri-fab.com
©2004Agri-Fab,Inc.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Agri-Fab 24206 Owner's manual

Agri-Fab
Brand
Agri-Fab
Model
24206
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents