Armstrong Flooring User manual

Brand: Armstrong

Model: Flooring

Type: User manual

LUXE PLANK

™

and the Lynx

™

Installation System

Patent pending.

THANK YOU FOR CHOOSING ARMSTRONG

FLOORING. Properly installed and cared for your new ﬂooring will be easy to maintain and will keep its great look

for years. If you have questions or comments, please visit us at www.armstrong.com or call our Customer Relations and Technical Services at 1 800 233 3823.

Product Adhesive Comment

LUXE PLANK Lynx technology with overlapping pressure sensitive

adhesive.

Planks are bonded to each other, not to the

substrate.

WARNING: EXISTING IN-PLACE RESILIENT FLOOR COVERING AND ASPHALTIC ADHESIVES. DO NOT SAND, DRY SWEEP, DRY

SCRAPE, DRILL, SAW, BEADBLAST, OR MECHANICALLY CHIP OR PULVERIZE EXISTING RESILIENT FLOORING, BACKING, LINING

FELT, ASPHALTIC “CUTBACK” ADHESIVE, OR OTHER ADHESIVE.

These existing in-place products may contain asbestos ﬁbers and/or crystalline silica. Avoid creating dust. Inhalation of such dust is a cancer and respiratory

tract hazard. Smoking by individuals exposed to asbestos ﬁbers greatly increases the risk of serious bodily harm. Unless positively certain that the existing in-place

product is a non-asbestos-containing material, you must presume it contains asbestos. Regulations may require that the material be tested to determine asbestos

content and may govern removal and disposal of material.

See current edition of the Resilient Floor Covering Institute (RFCI) publication Recommended Work Practices for Removal of Resilient Floor Coverings for

instructions on removing all resilient ﬂoor covering structures or contact your retailer or Armstrong World Industries, Inc. 1 800 233 3823.

The ﬂoor covering or adhesive in this package does NOT contain asbestos.

General Information

The Lynx installation system allows the planks to be

bonded together by an overlapped edge method. The

planks are not bonded directly to the subﬂoor and

this will help hide some minor substrate irregularities

without telegraphing through to the face of the

planks. The planks should be installed 1/8˝ away from

all vertical surfaces such as walls, cabinets, pipes, etc.

(a larger gap could cause excessive ﬂoor movement).

When installed in bathrooms, the gap should be ﬁlled

and sealed with a good quality siliconized or acrylic

caulk. The gap will then be covered with molding or

wall base. Base cabinets should not be installed on

top of the planks.

Included in each carton are two LUXE PLANK

transition strips. These can be used to change

direction during the installation process or to

make repairs as discussed in the Repair Procedure

instructions.

Keys to Successful LUXE PLANK Installation

 • Mostinstallationswillneedapproximately10%

cutting allowance added to the square footage

of the room.

 • Properconditioningofboththejobsiteandthe

ﬂooring is necessary. LUXE PLANK should not

be exposed to sudden changes in temperature

or moisture/humidity.

 • Store,transportandhandleLUXE PLANK so

as to prevent any distortions. Store cartons ﬂat,

never on edge. Distortions will not disappear

over time. Insure that the planks are laying ﬂat

at time of installation.

 • Donotcompresstheedgesoftheoating

installation in any way when installing other

ﬂooring materials next to LUXE PLANK.

Installation of carpet, metal strips and other

transition moldings should not push fullness

into the ﬂooring and should allow for some

slight movement wherever practical.

 • Protecttheoorfromheavyrollingloads,other

trades and replacement and/or movement of

appliances by using sheets of plywood or similar.

Suitable Substrates

All substrates listed must be properly prepared

and meet certain requirements. There may be

other exceptions and special conditions for these

substrates to be suitable for the Lynx Installation

System as noted below. (Refer to the Subﬂoors and

Underlayments section of the Armstrong Guaranteed

Installation System manual, F-5061, for more details,

or visit www.ﬂoorexpert.com.)

 • Concrete–dryandsmoothonallgradelevels

 • Suspendedwoodsuboorswithapproved

woodunderlayments–musthaveminimumof

18˝ well-ventilated crawl space underneath

 • Suspendedhardwoodooringthatisfully

adhered, smooth and square edge without

texture

 • Single-layer,fullyadhered,existingresilient

oors–mustnotbefoam-backedorcushion-

backed

 • Ceramictile,Terrazzo,Marble

 • PolymericPoured(seamless)Floors

DO NOT INSTALL OVER

 • Particleboardorwaferboard

 • Single-layerwoodsuboors*

 • Existingresilienttileoorsthatarebelowgrade

 • Existingcushion-backedvinylooring

 • Carpet

 • Hardwoodooringthathasbeeninstalled

directly over concrete

 • Onstairs,or,inroomswithslopingoorsor

ﬂoor drains

* Installation directly over single-layer wood subﬂoors

in new construction is not recommended. New

construction should have additional underlayment on

top of the subﬂooring and be installed as late in the

building schedule as possible; after permanent HVAC

is running, the home is properly conditioned, and other

trades have completed their work.

If it is unavoidable to install over single-layer wood

subﬂoors, it should only happen in remodel work

where the home has been occupied and conditioned

for a minimum of 1 year, having gone through the

initial winter season and dry-out of the new home. The

subﬂooring must meet all the substrate requirements

noted below.

Job Conditions/Preparations

• Allsubstratesmustbestructurallysound,dry,

clean, ﬂat, and smooth with minimal deﬂection.

Substrates must be free from excessive

moisture or alkali. Remove dirt, paint, varnish,

wax, oils, solvents, other foreign matter and

contaminates that could cause staining or

interfere with the bond of the adhesive.

 • Highspotsonthesubstrateshouldbe

leveled and low areas ﬁlled with appropriate

underlayments.

 • Donotuseproductscontainingpetroleum,

solvents or citrus oils to prepare substrates as

they can cause staining and expansion of the

new ﬂooring.

 • Inrenovationorremodelwork,removeany

existingadhesiveresiduesothat100%ofthe

overall area of the original substrate is exposed.

 • Wheninstallingoveranexistingresilientoor,

use S-199 One-Part Embossing Leveler or S-194

Patch, Underlayment & Embossing Leveler/S-195

Underlayment Additive to ﬁll and smooth any

embossing in the old ﬂoor.

 • Embossedceramictileoors,ceramicand

marblegroutjoints,andirregularitiesin

concrete should be ﬁlled and leveled using

S-194 Patch, Underlayment & Embossing

Leveler/S-195 Underlayment Additive or other

Armstrong cementitious underlayments.

 • Theareatoreceiveresilientooring,ooring

materials and adhesives should be maintained

between 65° F (18° C) and 85° F (29° C) for

48 hours before installation, during installation,

and 48 hours after completion. Maintain

temperatures between 55° F (13° C) and 85° F

(29° C) thereafter.

 • Resilientooringshouldonlybeinstalledin

temperature-controlled environments. It is

necessary to maintain a constant temperature.

Therefore, the permanent HVAC system

must be in operation before the installation

of resilient ﬂooring. Portable heaters are not

recommended as they may not heat the room

and subﬂoor sufﬁciently. Kerosene heaters

should never be used.

 • Forconcretesuboors,thewatervapor

emission level should be 5 lbs. /1000 sq.ft./24

hours, or less, as determined by calcium

chloride testing.

 • Radiantheatedsubstratesmustnotexceeda

maximum surface temperature of 85° F (29° C).

 • LUXE PLANK should not be exposed to direct

sunlight for prolonged periods. It can result

in discoloration and excessive temperatures

that may cause expansion. The use of drapes

or blinds is recommended during peak sunlight

exposure.

Procedure

Remove baseboard, quarter-round moldings, wall

base, appliances and furniture from room. For best

results, door trim should be under-cut to allow

ﬂooring to move freely without being pinched. After

preparation work, sweep and vacuum the entire

work area to remove all dust and debris.

Note: Planks are easily cut with a tile cutter or

by using a straight edge and utility knife. Score

the face of the plank several times and snap it.

If it doesn’t separate, lightly cut through the

back on the fold mark.

Layout

Wheneverpossible,planthelayoutsothatthejoints

intheplanksdonotfallontopofjointsorseamsin

theexistingsubstrate.Theendjointsoftheplanks

should be staggered a minimum of 6˝ apart. Do not

installoverexpansionjoints.

Determine which direction the planks will run.

Find the center of each of the end walls (the walls

perpendicular to the long dimension of the planks)

and place a pencil mark on the ﬂoor. Connect these

points by striking a chalk line down the center of the

room. Do a dry layout of planks from the center line

to the wall running parallel to the long direction of

the planks to determine the width of the last row of

planks.

CENTER

OF ROOM

Fig. 1 – Dry layout to determine width of border plank.

Avoid having border pieces less than 2-1/4˝ (5.7cm)

wide for the 4-1/2˝ (11.4cm) wide planks and less

than 3˝ (7.6cm) wide for the 6˝ (15.2cm) wide planks.

If you ﬁnd the border planks will be less than 1/2 the

width of the plank, the center starting line should be

shifted a distance equal to 1/2 the plank width. This

will “balance” the room and provide for a larger cut

piece at the wall.

Installation

Most installations will start along the longest, straight

wall in the room. The planks will be installed starting

in the corner of the room on the left side of the

starting wall (as you are facing it). The bottom

overlap ﬁlm should be exposed on the side and end

of the plank facing away from the left corner of the

starting wall (Figure 2). Remove the paper release

liner exposing the adhesive on the bottom overlap

ﬁlm.

Note: The pressure sensitive adhesive has a long

working time after the release paper has been

removed. It must, however, be protected from dust

and debris after the release paper is removed and

untilitiscoveredwithanotherplank.Ifthejobis

stopped prior to completion, leave the release paper

intact on the long edge only, of the last row of planks.

This will prevent dust or trafﬁc from other trades

from interfering with the adhesive’s performance.

Starting Wall

Pared Inicial

Mur de départ

Bottom overlap of plank base

Sobrelapamiento de debajo de la base de la tablilla

Rebord inférieur de la base de la planche

Fig. 2 – Left corner of starting wall.

CAUTION – Do not stand or walk on release

paper liner, as it is extremely slippery. Place it in a

wastebasket immediately upon removal from the plank.

Begin laying the ﬁrst row of planks. Place the top

overlap on the exposed bottom overlap ﬁlm (with

adhesive) of the preceding plank. Press into place

to obtain adhesion. Use a hand roller if available, or,

rub the seam with moderate hand pressure using

a clean dry cloth. Neatly butt the plank face edges

together. Continue, left to right, with the ﬁrst row of

planks until you near the end and need to cut the last

plank to ﬁt. Try to avoid having planks shorter than

8˝ at the ends of rows. You may have to cut some

additional length off the starting plank and slide the

ﬁrst row toward the left so the last plank will be at

least 8˝ in length. Remember to leave a gap of 1/8˝

from the end wall and cut the last piece in that row

to ﬁt.

Start the second row on the left side with a piece

cut to about 2/3 the length of the starting plank in

therstrow.Itisimportanttokeeptheendjoints

staggeredaminimumof6˝inadjacentrows

(Figure 3). Both the long side edges and the short

ends of planks should be neatly butted against

adjoiningplanksandthoseinadjacentrows.Useone

hand to hold the plank, and the other hand to guide

the edges into place by lowering the plank as you go.

It’s important to butt the edges together neatly. Press

into place or use a hand roller to obtain adhesion.

Ifthejointsarenottight,pulluptheplankand

reposition it immediately.

Note: LUXE PLANK

™

is precisely made to size

and squareness. After the ﬁrst 3 rows of planks are

installed they should be checked with a string line

to insure that rows are still running straight. If they

are not, it could be that the starting wall has some

irregularities that caused bowing in the installation. If

so, the starting row of planks may have to be scribed

and retrimmed to account for any unevenness in the

wall. This can be done without having to disassemble

the beginning rows.

Minimum 8” Length

Longitud Mínima de 8”

Longueur minimale de 20,32 cm (8 po)

Minimum 6” overlap at the joints

Mínimo de 6” de solapamiento en las uniones

Chevauchement minimal de 15,24 cm (6 po) aux joints

1/8” gap

De 1/8” de espacio

Espace de 13 mm (1/8 po)

Starting Wall

Pared Inicial

Mur de départ

Fig, 3 – Stagger end joints by 6˝, cut pieces at ends of

row should be 8˝ or greater.

Continue installing the remaining rows in similar

fashion.Maintainthe6˝minimumstaggeredendjoints

between rows and maintain the gap at perimeter

and vertical surfaces. After you have enough rows

in place, you may ﬁnd it easier to turn around and

work on top of the newly installed planks for the

remainder of the room.

LUXE PLANK transition strips, included in each

carton, can be used when changing direction of the

installation to return into a closet or alcove area of

the room. LUXE PLANK transition strips are also

recommended in the repair procedures for damaged

planks (see below).

After the installation is completed, roll the entire

ﬂoor, in both directions with a 100-pound roller. Use

a hand roller in conﬁned areas where the large roller

will not reach, such as under toe kicks.

Finishing the Installation

Replace molding or wall base, allowing slight

clearance between the molding and the planks. Nail

the molding to the wall surface, not through the

ﬂooring. At doorways and at other areas where

LUXE PLANK may meet other ﬂooring surfaces, it is

preferable to use a “T” molding or similar to cover

the exposed edge but not pinch the planks. Leave

asmallgapbetweentheplanksandtheadjoining

surface.

When replacing appliances, or whenever moving

heavy furniture over the ﬂooring, place a wood panel

undertheobject.Withoutmovingthepanel,slideor

rolltheobjectoverit.Followwithadditionalpanels

as needed. This prevents scratches, tears or buckling

of the ﬂooring material.

Care and Maintenance

IMPORTANT: Do not wash or scrub the new

LUXE PLANK ﬂooring for at least 5 days after the

installation. This will allow the planks to become

“seated” in the adhesive and prevent excess moisture

and cleaning agents from interfering with the

adhesive bond.

Proactive Protection for Your Floor

 • Whenmovingappliancesorheavyfurnitureit

is always wise to lay a plywood panel on your

ﬂoor and “walk” the item across it. This protects

your ﬂoor from scufﬁng and tears.

 • Useoorprotectors,suchasArmstrong

Floor Protectors, under furniture to reduce

indentation. As a general rule of thumb, the

heavier the item, the wider the ﬂoor protector

needed.

 • Placeawalk-offmatatoutsideentrancesto

reduce the amount of dirt brought into your

home. We strongly recommend mats without a

latex or rubber backing since these backings can

cause permanent discoloration.

 • AllArmstrongoorcareproductshavebeen

speciﬁcally developed to care for Armstrong

ﬂoors.

Caring for Your Floor

 • Sweeporvacuumregularly,toremoveloose

dirt which can scratch your ﬂoor.

Note: We do not recommend vacuums that

have a beater bar since it can visibly damage

your ﬂooring surface. Additionally, we do not

recommend electric brooms with hard plastic

bottoms with no padding as use may result in

discoloration and deglossing.

 • Wipeupspillsassoonaspossible.Neveruse

highly abrasive scrubbing tools on any resilient

ﬂoor.

 • Washyouroorregularlywithavinyloor

cleaner such as Armstrong Once ’n Done

Resilient & Ceramic Floor Cleaner.

 • DoNOTusedetergents,abrasivecleaners,or

“mop and shine” products. These products may

leave a dull ﬁlm on your ﬂoor.

 • Overtime,iftheshineonyouroorbeginsto

dull, apply Armstrong SatinKeeper

Resilient

Low Gloss Floor Finish to restore the

appearance of LUXE PLANK. Do NOT use

paste wax or solvent based polishes.

 • Vinylooring,likeothertypesofsmoothoors,

can become slippery when wet. Allow time for

ﬂoor to dry after washing. Immediately wipe up

wet areas from spills, foreign substance, or wet

feet.

Repair Procedure

For damaged bottom overlap ﬁlm on plank

prior to installation.

If the exposed ﬁlm with adhesive is severely wrinkled

or damaged prior to installation the damaged

portion can be removed and replaced with a piece

of the LUXE PLANK transition strips supplied in

everycarton.Sometimes,justbendingitintheother

direction will allow the ﬁlm to lay ﬂat enough for

normal installation. If this doesn’t work:

1. Turn the plank over so the back is exposed

2. Use a utility knife to score through the back

ﬁlm with a straight cut 2 inches from and

parallel to the edge of the damaged ﬁlm

3. Make additional cuts to isolate the damaged

portion of ﬁlm from the undamaged areas

4. Carefully peel the damaged area from the back

of the plank, leaving the undamaged areas intact

5. Cut a piece of the LUXE PLANK transition

strip to the proper length to replace the

damaged ﬁlm

6. Strip release paper from the LUXE PLANK

transition strip and adhere it to the back of

the plank in the void where the damage was

removed (do not overlap the LUXE PLANK

Page is loading ...

Armstrong Flooring User manual

Brand: Armstrong

Model: Flooring

Type: User manual

Download PDF

report

in other languages

français: Armstrong Flooring Manuel utilisateur
español: Armstrong Flooring Manual de usuario

Armstrong Flooring User manual

Armstrong Flooring User manual

in other languages

Related papers

Other documents