Ohlins YA974 Mounting Instruction

Type
Mounting Instruction
Öhlins Racing AB
Box 722
S-194 27 Upplands Väsby, Sweden
Phone +46 8 590 025 00
fax +46 8 590 025 80
© Öhlins Racing AB. All rights
reserved. Any reprinting or
unauthorized use without the written
permission of Öhlins Racing AB
is prohibited.
www.ohlins.com
Öhlins products are subject to
continuous improvement and
development, therefore, although
these instructions include the most
up-to-date information available at
the time of printing, minor updates
may occur.
To find the latest information contact
your Öhlins distributor. Please
consult your Öhlins dealer if you
have any questions regarding the
contents in this document.
Shock Absorber for ATV Yamaha Raptor 250 - Front
YA 974
Mounting Instructions
Part No Pcs
Shock absorber YA 974 2
C-spanner 00710-01 2
Öhlins Sticker 00197-01 2
Memo Notes Sticker 01180-01 1
Owner’s Manual ATV 07235-01 1
Before installing this product, check the
contents of the kit. If anything is missing, please
contact your nearest Öhlins dealer.
Kit Contents
Recommended set-up
Rebound damping 15 clicks
Compression damping 15 clicks
Shock absorber data
Length 353 mm
Stroke 109 mm
Free sag and Ride height
Free sag, front 60±5 mm
2½±¼’
Free sag, rear 30±5 mm
1¼±¼’
Ride height, front 80±5 mm
3¼±¼’
Ride height, rear 105±5 mm
4½±¼’
Set-up Data
Please note that during storage and
transportation, especially at high ambient
temperature, some of the oil and grease used for
assembling may leak and stain the packaging.
This is in no way detrimental to the product,
wipe off the excessive oil/grease with a cloth.
Part no. YA974_0
Issued 2009-06-01
Warning!
Before installing this product, read the Öhlins
Owner’s Manual. The shock absorber is an
important part of your vehicle and may affect the
stability.
Rider’s weight A-arm: Standard
65kg /165Lb Long spring 06390-04
Spring rate Prog 21-30 N/mm
80kg /187Lb Long spring 06390-05
Spring rate Prog 24-33 N/mm
95kg /209Lb Long spring 06390-06
Spring rate Prog 27-36 N/mm
Total spring preload: 4 mm
Cross-over 18 mm
Spring Guide
Adjustments
Rebound
Damping Adjuster
Warning!
Before riding, always make sure that the
basic settings made by Öhlins are according
to recommended Set-up Data. Read about
adjustments and setting up in the Öhlins
Owner’s Manual before you make any
adjustments. Contact an Öhlins dealer if you
have any questions about setting up the shock
absorber.
Spring Preload
Adjuster
Compression
Damping Adjuster
1 2
Adjust Spring How to install
Warning!
It is advisable to have an Öhlins dealer install the
shock absorber.
When installing, read the Vehicle Service Manual.
1
Raise the front end of the vehicle so that
the original shock absorbers are in a neutral
position.
Warning!
Make sure the vehicle is securely supported so
that it will not tip.
2
Remove the original shock absorbers.
3
Install the Öhlins shock absorbers in the
same positions as the original units. Fasten
the upper attachment rst. The piggy back
reservoirs should be at the top and facing
outwards.
4
Fasten the lower attachment. Raise or lower
the wheels slightly to make the attachment t.
5
Tighten the attachment screws to the correct
torque. Consult your ATV Owners manual.
1
4
3
6
Check sag and ride height according to the
Öhlins owners manual. See also Set-up data
for this specic shock absorber kit on the
next page.
Caution!
Make sure that all screws are tightened to the
correct torque and that nothing fouls or restricts
movement of the shock absorber when the
suspension is fully compressed or extended.
A
Spring
platform
clamp
Spring
platform
Spring Preload = A - B
A Free spring length
B Installed spring length
A
B
1
Measure the free length of the spring (A).
2
Loosen the screw on the spring platform
clamp so that you can move the spring
platform as far up as needed to install the
spring.
3
Put the shock absorber up-side-down in a
vice so that you can install the spring and the
spring clip.
Note!
The spring platform and spring are press fitted.
Push hard to install the spring.
4
Measure the spring length. Adjust the spring
preload to the recommended setting, see
section Set-up data in this folder.
5
Install the shock absorber to the vehicle
according to the procedure in this folder.
Check sag and ride height (see Owner’s
Manual) and adjust spring preload again if
necessary.
Note!
Tighten the screw on the spring platform clamp
before riding the motorcycle.
1
2
3
Spring
Spring clip
4
  • Page 1 1
  • Page 2 2

Ohlins YA974 Mounting Instruction

Type
Mounting Instruction

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI