ACME LP-2304 User manual

Brand: ACME

Model: LP-2304

Category: Floodlights

Type: User manual

The ACME LP-2304 is a professional LED wash light fixture with 2304 0.8W RGBW LEDs, boasting a 110-degree beam angle and IP65 weather resistance, ideal for discotheques, clubs, bars, parties, and mobile DJs. It offers 13-channel modes, allowing for intricate color mixing and dynamic effects. The fixture has a total power consumption of 1500W and can be daisy-chained with up to 2 fixtures at 220V.

1. Safety Instructions ............................................................................................................................2

2. Technical Specifications ....................................................................................................................3

3. Installation and Connection .............................................................................................................4

4. How to set the unit ...........................................................................................................................5

4.1 Rear Panel .......................................................................................................................................5

4.2 Main Function.................................................................................................................................6

5. How to control the unit ..................................................................................................................12

6. DMX512 configuration ...................................................................................................................13

7. DMX512 Connection.......................................................................................................................15

8.Troubleshooting ...............................................................................................................................16

9. Fixture Cleaning ..............................................................................................................................17

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer will

not accept liability for any resulting defects or problems.

Unpack and check carefully to ensure that there is no transportation damage before using the

unit.

The equipment is suitable for wet/indoor use.

DO install and operate by qualified operator.

DO NOT allow children to operate the fixture.

Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head only.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots is blocked, otherwise the unit will be overheated.

Before operation, ensure that you are connecting this product to the proper voltage in

accordance with the specifications in this manual or on the product’s specification label.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃. Do not

operate this product at a lower or higher temperature.

DO NOT connect the device to any dimmer pack.

Keep flammable materials away from the fixture while operating to avoid fire hazard.

Make sure the power cord is not crimped or damaged; replace it immediately if damaged.

Unit’s surface temperature may reach up to 65℃. DO NOT touch the housing bare-handed

during its operation.

Avoid any flammable liquids, water or metal from entering the unit. Once it happens, cut off

the mains power immediately.

Please read the instruction carefully which includes important information about

the installation, usage and maintenance.

DO NOT operate in a dirty or dusty environment. DO clean the fixture regularly.

DO NOT touch any wire during operation as there might be a hazard of electric shock.

Avoid entanglement of the power cord with other wires.

The minimum distance to objects/surface must be more than 1 meters.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

DO NOT open the housing as there are no user serviceable parts inside.

DO NOT attempt to operate this unit if it becomes damaged. DO NOT attempt any repairs

yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center if needed.

Disconnect this product from its power source before servicing.

DO use the original packaging if the device is to be transported.

Avoid direct eye exposure to the light source while the product is on.

DO NOT operate this product if you see damage on the housing, shields, or cables. Have the

damaged parts replaced by an authorized technician at once.

1. Consignes de sécurité

ATTENTION

Veuillez conserver ce guide de l'utilisateur pour une consultation future. Si vous vendez l'appareil à

un autre utilisateur, assurez-vous qu'il reçoive également ce manuel d'instructions.

Important:

Les dommages causés par le non-respect de ce manuel d'utilisation ne sont pas couverts par la

garantie. Le revendeur n'acceptera aucune responsabilité pour les défauts ou problèmes qui en

résultent.

Déballez et vérifiez soigneusement qu'il n'y a pas de dommages dus au transport avant

d'utiliser l'appareil.

Équipement adapté aux endroits secs et aux environnements humides

L’installation et la mise en fonctionnement doit être effectué par un opérateur qualifié.

NE PAS permettre aux enfants d'utiliser l'appareil.

Utilisez une chaîne de sécurité lors de la fixation de l'unité. Manipulez l'appareil en portant sa

base au lieu de la tête uniquement.

L'unité doit être installée dans un endroit avec une ventilation adéquate, à au moins 50cm des

surfaces adjacentes.

Assurez-vous qu'aucune fente d'aération du luminaire n'est obstruée, sinon il risque de

surchauffer.

Avant toute utilisation, assurez-vous que vous connectez ce luminaire à la tension appropriée

conformément aux spécifications que vous trouverez dans ce manuel ou sur l'étiquette des

spécifications collée sur la base du luminaire.

Il est important de relier le file jaune/vert à la terre afin d'éviter tout choc électrique.

Température ambiante minimale TA: 0. Température ambiante maximale TA: 40. N'utilisez pas

ce luminaire à des températures inférieures ou supérieures.

NE PAS connecter le luminaire à un pack de gradateurs.

Gardez les matériaux inflammables à l'écart du luminaire pendant le fonctionnement pour

éviter tout risque d'incendie.

Veuillez lire attentivement les instructions qui contiennent des informations

importantes sur l'installation, l'utilisation et l'entretien.

Assurez-vous que le cordon d'alimentation n'est pas pincé ou endommagé; remplacez-le

immédiatement s'il est endommagé.

La température de surface de l'unité peut atteindre 65℃. NE PAS toucher les capots à mains

nues pendant son fonctionnement.

Évitez que des liquides inflammables, de l'eau ou du métal ne pénètrent dans l'appareil. Si cela

se produit, coupez immédiatement l'alimentation secteur.

NE PAS utiliser le luminaire dans un environnement sale ou poussiéreux. Cette appareil doit

être nettoyer régulièrement.

NE touchez AUCUN file pendant le fonctionnement car il pourrait y avoir un risque de choc

électrique.

Évitez l'enchevêtrement du cordon d'alimentation avec d'autres fils.

La distance minimale de projection sur des objets ou sur des surfaces doit être supérieure à 1

mètres.

En cas de problème de fonctionnement grave, arrêtez immédiatement d'utiliser l'appareil.

N'allumez et n'éteignez jamais ce luminaire à maintes reprises.

NE PAS ouvrir le boîtier car il ne contient aucune pièce réparable par l'utilisateur.

NE PAS mettre ce luminaire en fonctionnement s'il est endommagé. N'effectuez pas de

réparations vous-même. Les réparations ne doivent être effectuées par des personnes non

qualifiées, cela peut entraîner des dommages ou des dysfonctionnements. Veuillez contacter le

centre d'assistance technique agréé le plus proche si nécessaire.

Débranchez ce produit du secteur avant de procéder à l'entretien.

Utiliser l'emballage d'origine si l'appareil doit être transporté.

Évitez une exposition directe des yeux à la source lumineuse lorsque le produit est allumé.

N'utilisez PAS ce produit si vous constatez des dommages sur le boîtier, les blindages ou les

câbles. Faites remplacer immédiatement les pièces endommagées par un technicien agréé.

2. Technical Specifications

13 channel Modes;

Ideal for discotheques, clubs, bars, parties, Mobile DJs, etc.

Input Voltage:100-240V~ 50/60Hz

Total Power consumption: 1500W

Power Cord Daisy Chain: 1Fixtuer(120V); 2 Fixtuer(220V);

Beam Angle:110°

IP Grade:IP 65

LED Sources:

Dimension:

Weight:

0.8W RGBW x 2304

623x123x387mm

16 Kgs

3. Installation and Connection

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed

to avoid vibration and slipping while operating. Always ensure that the structure to which you are

attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always

use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch

of people and has no one pass by or under it. The unit should be mounted in the height of 0 to 30m.

Method for using lamp hook and safety rope

4. How to set the unit

4.1 Rear Panel

○ Display: Show the various menus and the selected functions；

○ Button：

MENU To select the programming functions

DOWN

To go forward in the selected functions

To go backward in the selected functions

ENTER

To confirm the selected functions

○

3Breathable punishment

○

4 Power input/output

For DMX512 link, use 3/5 -pin XLR plug cable to input DMX signal, and to link the next unit.

○

5 DMX input/output:

For DMX512 link, use 3/5 -pin XLR plug cable to input DMX signal, and to link the next unit.

○

6Ethernet in/ Ethernet Thru: For ArtNet link

4.2 Main Function

To select any functions, press MENU button until the required one is shown on the display. Select the

function by ENTER button. Use DOWN and UP button to change the mode. Once the required mode has

been selected, press ENTER button to setup or it will return to the main functions without any change

after idling 30 seconds automatically. Back to the functions without any change press MENU button.

The main functions are shown below:

Network

Art-Net Settings

Sacn Settings Sacn Settings

sACN Priority

1-32000

0-200

Connect Option

Auto

DMX

Art-Net

sACN

Standard

Quiet

RDM UIDxxxxxxxxxxxx

Power Mode

Fixture Errors

Reset Error Log

Error Logs

10H

DMX Address

Select the DMX Address, press enter to confirm, and the current DMX Address will be displayed on the

display screen. Use the UP / DOWN button to select 001 ~ 512 Addresses, and press the ENTER button

to save. Press the MENU button to return to the previous MENU or wait 30 seconds to automatically

exit the menu mode.

Channel Mode

Select the Channel Mode, press the ENTER button. Use the DOWN and UP button to select the Channel,

there are 11 channel Modes. Once selected, press the ENTER button to store. Press the MENU button

back to the last menu without any change or idling 30 seconds to exit menu mode.

DMX Last State

Select the DMX Last State, press the ENTER button. Use the DOWN and UP button to select Blackout or

Hold . Once selected, press the ENTER button to store. Press the MENU button back to the last menu

without any change or idling 30 seconds to exit menu mode.

DMX Settings

Enter MENU mode, select DMX settings, confirm by pressing ENTER on, and use UP / DOWN on

to select: DMX Address, Ethernet Setup and Connect Option.

Ethernet Setup

Select Ethernet Setup, press ENTER to confirm, and the current mode will be displayed on the display

screen. Select Network, Art-Net Settings or Sacn Settings through UP / DOWN button. When selecting

Network, select IP Address or Subnet Mask through UP / DOWN button. When selecting Art-Net

Settings , select Net, Sub-Net or Universe through UP / DOWN button, When the Art-Net setting is

selected, select the sACN Universe or sACN Priority the through UP / DOWN button, and press the

ENTER button to save. Each Network parameter of the lamp must be consistent with that on the

console before it can be controlled by the Network signal of the console. Press the menu button to

return to the previous MENU or wait 30 seconds to automatically exit the menu mode.

Connect Option

Select the Connect Option, press the ENTER button. The current mode will be displayed on the display

screen, which can be selected by UP / DOWN button: Auto, DMX, Art-Net or sACN, and press enter

button to save. Press the MENU button to return to the previous MENU or wait 30 seconds to

automatically exit the menu mode.

11H

Optically Linear Square Law Inverse-Square Law S-Curve

Mode 1(Optically Linear): The increase in light intensity appears to be linear as DMX value is increased.

Mode 2(Square Law): Light intensity control is finer at low levels and coarser at high levels.

Mode 3(Inverse Square Law): Light intensity control is coarser at low levels and finger at high levels.

Mode 4(S-cure): Light intensity control is finger at low levels and high levels and coarser at medium

levels.

Dimmer Speed

Select the Dimmer Speed, press the ENTER button. Use the DOWN and UP button to select Fast or

Smooth. Once selected, press the ENTER button to setup or exit menu mode without any change after

30 seconds. Back to the functions without any change press the MENU button again.

White Balance

Select the White Balance, press the ENTER button to confirm. It can be adjusted with the whole fixture,

or it can be adjusted independently for each block.Use the UP and DOWN button to select

Red/Green/Blu/White, press the ENTER button to store, then use the UP and DOWN button to adjust

the value from (125~255), press the ENTER button to confirm. (DMX signal will be the first priority under

Manual Mode.) Once selected, press the ENTER button to store. Press the MENU button back to the last

menu without any change or idling 30 seconds to exit menu mode.

Language

Select the Language, press the ENTER button to confirm. Use the UP and DOWN button to adjust

English or Chinese .Once selected, press the ENTER button to store. Press the MENU button back to

the last menu without any change or idling 30 seconds to exit menu mode.

12H

Manual Test

Select the Manual Mode, press the ENTER button to confirm. Use the UP and DOWN button to adjust

the value for Red,Green,Blue,White, Intensity, Durate or Rate from 0~255, press the ENTER button to

confirm. (DMX signal will be the first priority under Manual Mode.) Once selected, press the ENTER

button to store. Press the MENU button back to the last menu without any change or idling 30 seconds

to exit menu mode.

Auto Test

Select Auto Test, press the ENTER button to confirm. The unit will test by itself automatic. Press the

MENU button back to the last menu or idling 30 seconds to exit menu mode.

Temperature

Select Temp., press the ENTER button to confirm. Display will show the temperature of the fixture.

Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.

Fixture Hours

Select Fixture Hours, press the ENTER button to confirm. Display will show the number of working

hours of the unit. Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.

RDM UID

To select RDM UID, press the ENTER button to confirm, RDM UID will show on the display, press the

MENU button back to exit.

Select Power Mode, press ENTER to confirm that the current Mode is displayed on the display, select

either: Standard or Quiet by the UP/DOWN button, and press ENTER to save. Press the MENU button to

go back to the previous MENU or wait 30 seconds to automatically exit MENU mode.

Power Mode

13H

Fault report :

1、Fan.Error

Check that the fan is not running

Check the PCB board related detection circuit is damaged

2、Temp.Errot

Check that the test leads are in good contact and open

Check if the thermistor is broken

Check PCB board related circuit is damaged

Software Version

Select Software Version , press the ENTER button to confirm. The display will show the version of

software of the unit. Press the MENU button back to the last menu or idling 30 seconds to exit menu

mode.

Select Factory Reset, press the ENTER button to confirm. Use the UP and DOWN button to adjust the

NO/Yes. Select Yes, fixture will resume factory settings. Press the MENU button back to the last menu or

idling 30 seconds to exit menu mode.

Factory Reset

Error Logs

To select Error Logs, press the ENTER button to confirm. Use the UP/DOWN button to select Fixture

Errors or Reset Error Log, press the ENTER button to store. To select Reset Error Log, press the

ENTER button to confirm, use the UP/DOWN button to select No or Yes, press the ENTER button to

store. To select Yes, press the ENTER button to confirm, use the UP/DOWN button to set the

password 050, Press the MENU button to return to the previous menu or wait one minute to

automatically exit the menu mode.

14H

5. How to control the unit

1.By DMX controller；

No need to turn the unit off when you change the DMX address, as new DMX address setting will be

affected at once. Turn on the unit, under the DMX signal , the LED will display the saved channel address

（001-512）.

RDM function table

DMX START 0-512

MANUFAC TURER ACME

DEVICE MODEL DESCRIPTION THUNDERSTRUCK

DMX PERSONALITY DMX 4/4Channel( 8 bit)

DMX 8/8Channel (16

bit) DMX 8/8 Channel

DMX 52/52 Channel

DMX12/1 Piexl

DMX16/2V Piexl

DMX16/2H Piexl

DMX20/3 Piexl

DMX24/4 Piexl

DMX32/6V Piexl

DMX32/6H Piexl

DMX56/12 Piexl

DEVICE LABEL THUNDERSTRUCK

IDENTIFY DEVICE Off/On

DEVICE HOURS

SOFTWARE

RESET DEVICE Warm/Cold

15H

6. DMX512 configuration

Channel Mode：

16H

17H

18H

7. DMX512 Connection

Mode connection：

1. Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the fixture to

the input of the next fixture. The cable cannot be branched or split to a “Y” cable. Inadequate or

damaged cables, soldered joints or corroded connectors can easily distort the signal and shut down

the system

2. The DMX output and input connectors are pass-through to maintain the DMX circuit when one of

the units’ power is disconnected.

3. At last fixture, the DMX cable has to be terminated with a terminator to reduce signal errors. Solder

a 120-ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in

the DMX-output of the last fixture.

4. Each lighting fixture needs to have an address set to receive the data sent by the controller. The

address number is between 0-511 (usually 0 & 1 are equal to 1).

5. 3/5 pin XLR connectors:.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

8.Troubleshooting

Following are a few common problems that may occur during operation. Here are some suggestions for

easy troubleshooting:

A. The fixture does not work, no light

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

19H

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

2. If the DMX LED is on and no response to the channel, check the address settings and DMX polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the fixture

or the previous one.

4. Try to use another DMX controller.

5. Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or

interference to DMX interface circuit.

9. Fixture Cleaning

The cleaning of internal must be carried out periodically to optimize light output. Cleaning frequency

depends on the environment in which the fixture operates: damp, smoky or particularly dirty

surrounding can cause greater accumulation of dirt on the fixture’s optics.

 Clean with soft cloth using normal glass cleaning fluid.

 Always dry the parts carefully.

 Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.

Page is loading ...

ACME LP-2304 User manual

Brand: ACME

Model: LP-2304

Category: Floodlights

Type: User manual

Download PDF

report

in other languages

français: ACME LP-2304 Manuel utilisateur

ACME LP-2304 User manual

ACME LP-2304 User manual

in other languages

Related papers

Other documents