Winners Only DQT145124E Assembly Instructions

Type
Assembly Instructions
Page 1 of 2 MADE IN MALAYSIA
PART NO FIGURE DESCRIPTION Q'TY
Wood Seat
Chair Back
PARTS LIST
1 Pce
Seat Frame 1 Pce
1 Pce
1 Pce
1 Pce
Hardware Bag
DQT145124-02
DQT145124-03
DQT145124-04
DQT145124-05 Front Leg (Right)
1 Pce
DQT145124-06 Front Leg (Left)
2 Pcs
DQT145124-07 Side Stretcher (Right / Left)
DQT145124-01
ALR-11279D-SHM
Front Stretcher 1 Pce
DQT145124-10
NAPOLEON BARSTOOL
DQT145124
DQT145124-02
DQT145124-03 DQT145124-04
DQT145124-05
DQT145124-06
DQT145124-07
DQT145124-07
DQT145124-10
Turn the chair upright. Check its balance and tighten all screws and bolts to complete the assembly.
STEP 3
NAPOLEON BARSTOOL
HARDWARE PARTS :
JCBC Bolt
(Short)
2 pcs
Pan Head
Screw
6 pcs JCBC Bolt
(Long)
6 pcs Lock Washer
8 pcs Flat Washer
8 pcs Allen Key
1 pce Glue
1 pce
ASSEMBLY :
1. Position the chair back on a soft surface such as a carpet. Place the box system assembly (Hardseat is pre-attached to the seat
frame in assembly) on to the middle rail of the chair back with the dowel fully inserted into the pre-drilled hole.
1.1. Insert JCBC Bolt (Long) through a Lock Washer and a Flat Washer into the pre-drilled holes on the apron frame at rear corners.
1.2. Insert the JCBC Bolt (Short) through a Lock Washer and a Flat Washer into the pre-drilled holes on the apron frame at rear rail.
2. Apply Glue to all the pre-drilled holes before attaching all stretchers. Insert each side stretcher into pre-drilled holes on both of the
rear legs, make sure that screw holes on the stretcher are facing down. Insert the front stretcher into the pre-drilled holes on the front
legs. Place the assembled front legs to corner block of the frame, and insert side stretcher into the legs.
2.1. Insert the JCBC Bolt (Long) through a Lock Washer, a Flat Washer and the pre-drilled holes of corner block into the pre-drilled holes
on the front leg, tighten the JCBC Bolt with Allen Key provided. But do not fully tighten the bolts yet.
2.2. Insert Pan Head Screw into front stretcher and side stretcher through the pre-drilled holes, tighten with screw driver. (Not Provided)
Chair Back
Dowel
STEP 1
(Fig 1)
Allen Key
JCBC Bolt(Short)
Lock Washer
Flat Washer
(Fig.1.2)
Box
System
Assembly
Flat Washer
Lock Washer
JCBC Bolt (Long)
Allen Key
(Fig.2.1)
Left Leg
Left & Right
Side Stretcher
Right Leg
Front
Stretcher
STEP 2
Apply Glue and insert stretcher
with screw holes facing down.
(Fig 2)
Page 2 of 2 MADE IN MALAYSIA
ALR-11279D-SHM
DQT145124
CARE INSTRUCTION
~ Be sure to use the same type of polish consistenly.
Your furniture will appear cloudy or streaky if oil
based or wax based polishes are interchanged.
~ Spray your furniture surface evenly. Wipe in a
circular motion with a soft clean cloth.
(Fig.2.2)
Pan Head Screw
Apply Glue
Allen Key
JCBC Bolt(Long)
Lock Washer
Flat Washer
(Fig.1.1)
  • Page 1 1
  • Page 2 2

Winners Only DQT145124E Assembly Instructions

Type
Assembly Instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI