Classic Exhibits SYK-2039 Setup Instructions

Type
Setup Instructions
© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
10’
20’
Perspective View
SYK-2039 - 10’ x 20’ Portable Backlit Display
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq ft
Plan View
© 2023
Order #XXXXX
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, keep all
knobs & connectors attached to
extrusions during disassembly.
Part Identification - Numbering
7A
Engaged Lock
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
WARNING
General Information
© 2023
Order #XXXXX
TSP49 Profile
All knobs must be tightened securely to ensure a proper connection.
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Corner
Connector Corner
Connector
Corner
Connector
Corner
Connector
COMPLETED ASSEMBLY
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.
Straight Connection
3) Tighten all knobs to secure connection.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
Slide connector across seam of extrusions.
Tighten all knobs.
All knobs must be tightened securely to ensure a proper connection.
Straight Connector
2) Loosen all knobs, then slide straight
connector across the seam of extrusions.
Tool-less Frame Assembly
© 2023
Case 1 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1
(Bottom level)
Level 2 Level 3 Level 4 Level 5
13
14
2,4
1 3
8,10 6,9
11 12
5,7
Lights
Blocker
Setup Hardware
Graphics
Case Packing
© 2023
Case 2 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1
(Bottom level)
Level 2 Level 3
1 3
5,6
2 4
7,8
9
Level 4 Level 5
Lights
Blocker
Setup Hardware
Graphics
Case Packing
© 2023
Case 3 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1
(Bottom level)
Level 2 Level 3
1 3
5,6
2 4
7,8
9
Level 4 Level 5
Lights
Blocker
Setup Hardware
Graphics
Case Packing
© 2023
Step 1 of 7
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Item
1
2
3
4
5
6
7
8
9
10
13
14
Qty.
1
1
1
1
1
1
1
1
1
1
1
1
Steps:
Refer to the Tool-less Frame Assembly general information page.
1) Assemble vertical extrusions [1-2], [3-4] & horizontals [5-6-7], [8-9-10]
together, using Tool-less Spline Connector labeled [X]. Note: Hanging clips
on horizontals must face back of frame.
2) Connect vertical assemblies [1/2], [3/4] between horizontal
assemblies [5/6/7], [8/9/10], using Tool-less Corner Connectors labeled [A].
3) Install Base Plates [13] & [14] to bottom corners of frame assembly
as shown. See Base Plate Attachment detail.
Description
45”h TSP49 Vertical Extrusion
41”h TSP49 Vertical Extrusion
45”h TSP49 Vertical Extrusion
41”h TSP49 Vertical Extrusion
36.5”w TSP49 Horizontal Extrusion w/ 1 clip
36.5”w TSP49 Horizontal Extrusion w/ 5 clips
36.5”w TSP49 Horizontal Extrusion w/ 1 clip
36.5”w TSP49 Horizontal Extrusion w/ 1 clip
36.5”w TSP49 Horizontal Extrusion w/ 5 clips
36.5”w TSP49 Horizontal Extrusion w/ 1 clip
6” x 22” Base Plate w/ flange (right)
6” x 22” Base Plate w/ flange (left)
**
1
2
3
4
8
10
9
14
13
5
6
Tool-less Spline Connector
1. Place extrusions end-to-end.
2. Slide tool-less connectors
across seam of extrusions.
*
3. Tighten all knobs to secure connection.
Tool-less Corner Connector
1. Slide extrusion onto
Corner Connector.
2. Tighten all knobs to
secure connection.
*
Keep corner connectors attached to horizontal extrusions.
Assemble frame flat on ground.
7
FRONT VIEW
TOP VIEW
Right Base Plate
TOP VIEW
Left Base Plate
Base Plate Attachment
*
Place key hole over bolt on panel & slide down.
Twist knob to secure connection.
Front
Base Plate
key hole
bolt
*
X
*
X
*
X
A
*
A
*
A*
A
*
*
X
*X
*
X
*
*****
*
*****
clip
w/ S10
clip
w/ S10
*
Keep all clips attached to horizontal extrusions
DO NOT DISASSEMBLE
All Hanging Clips should the
face back of the booth.
Hanging Clip
clip
BACK VIEW
Middle Backwall Frame Assembly
© 2023
Step 2 of 7
Order #XXXXX
Locked layer contains
placeholder marks.
Item
1
2
3
4
5
6
7
8
9
Qty.
1
1
1
1
1
1
1
1
1
Description
45”h TSP49 Vertical Extrusion
45”h TSP49 Vertical Extrusion
45”h TSP49 Vertical Extrusion
45”h TSP49 Vertical Extrusion
27.35”w TSP49 Horizontal Extrusion
27.35”w TSP49 Horizontal Extrusion
27.35”w TSP49 Horizontal Extrusion
27.35”w TSP49 Horizontal Extrusion
6” x 22” End Base Plate w/ foot
When assembled
Tool-less Spline Connector
1. Place extrusions end-to-end.
2. Slide tool-less connectors
across seam of extrusions.
*
3. Tighten all knobs to secure connection.
Tool-less Corner Connector
1. Slide extrusion onto
Corner Connector.
2. Tighten all knobs to
secure connection.
*
Keep corner connectors attached to horizontal extrusions.
Assemble frame flat on ground.
Steps:
Refer to the Tool-less Frame Assembly general information page.
1) Assemble vertical extrusions [1-2], [3-4] & horizontal extrusions [5-6], [7-8]
together, using Tool-less Spline connectors labeled [X]. Note: Hanging clips
on horizontals must face back of frame.
2) Connect vertical assemblies [1/2], [3/4] between horizontal
assemblies [5/6], [7/8], using Tool-less Corner Connectors labeled [A].
3) Install Base Plate [9] to bottom corners of frame assembly
as shown. See Base Plate Attachment detail.
*
1
2
3
4
56
7
8
9
FRONT VIEW
*
X
A
*
A
*
A*
A
*
*
X
*X
*
X
1) Place key hole over bolt on panel
& slide down.
2) Twist knob to secure connection.
Base Plate Attachment
*
bolt
knob
Base Plate
threaded
hole
key hole
*
Keep all clips attached to horizontal extrusions
DO NOT DISASSEMBLE
All Hanging Clips should the
face back of the booth.
Hanging Clip
clip
BACK VIEW
****
****
Left Backwall Frame Assembly
© 2023
Step 3 of 7
Order #XXXXX
Locked layer contains
placeholder marks.
Item
1
2
3
4
5
6
7
8
9
Qty.
1
1
1
1
1
1
1
1
1
Description
45”h TSP49 Vertical Extrusion
45”h TSP49 Vertical Extrusion
45”h TSP49 Vertical Extrusion
45”h TSP49 Vertical Extrusion
27.35”w TSP49 Horizontal Extrusion
27.35”w TSP49 Horizontal Extrusion
27.35”w TSP49 Horizontal Extrusion
27.35”w TSP49 Horizontal Extrusion
6” x 22” End Base Plate w/ foot
When assembled
Tool-less Spline Connector
1. Place extrusions end-to-end.
2. Slide tool-less connectors
across seam of extrusions.
*
3. Tighten all knobs to secure connection.
Tool-less Corner Connector
1. Slide extrusion onto
Corner Connector.
2. Tighten all knobs to
secure connection.
*
Keep corner connectors attached to horizontal extrusions.
Assemble frame flat on ground.
3
4
1
2
65
8
7
9
FRONT VIEW *
Steps:
Refer to the Tool-less Frame Assembly general information page.
1) Assemble vertical extrusions [1-2], [3-4] & horizontal extrusions [5-6], [7-8]
together, using Tool-less Spline connectors labeled [X]. Note: Hanging clips
on horizontals must face back of frame.
2) Connect vertical assemblies [1/2], [3/4] between horizontal
assemblies [5/6], [7/8], using Tool-less Corner Connectors labeled [A].
3) Install Base Plate [9] to bottom corners of frame assembly
as shown. See Base Plate Attachment detail.
*
X
A
*
A
*
A*
A
*
*
X
*X
*
X
1) Place key hole over bolt on panel
& slide down.
2) Twist knob to secure connection.
Base Plate Attachment
*
bolt
knob
Base Plate
threaded
hole
key hole
*
Keep all clips attached to horizontal extrusions
DO NOT DISASSEMBLE
All Hanging Clips should the
face back of the booth.
Hanging Clip
clip
BACK VIEW
****
****
Right Backwall Frame Assembly
© 2023
Step 4 of 7
Order #XXXXX
Locked layer contains
placeholder marks.
**
Left Frame
Steps:
1) Connect vertical of Left Frame Assembly to
Base Plate of Middle Frame Assembly.
See Base Plate Attachment detail.
2) Attach vertical of Right Frame Assembly to
Base Plate of Middle Frame Assembly.
See Base Plate Connection detail.
When assembled
FRONT VIEW
1
2
3
4
3
4
3
4
TOP VIEW
Left Base Plate
TOP VIEW
Right Base Plate
bolt
key hole
Front
Base Plate Attachment
*
Place key hole over bolt on panel & slide down.
Twist knob to secure connection.
Base Plate
Right Frame
Backwall Frames Connection
© 2023
Step 5 of 7
Order #XXXXX
Locked layer contains
placeholder marks.
Center
light
curtain
BACK VIEW
OF MIDDLE FRAME
ELEVATION VIEW
Steps:
1) Install center Lattice Light curtain to back of middle frame.
2) Assemble vertical extrusions [11-12] together,
using Tool-less Spline Connector labeled [X].
3) Connect vertical assembly [11/12] between S10 extrusions
on lower & upper clips of middle frame, using Connection Lock w/ Knob.
4) Install remaining Lattice Light curtains to back of middle, left & right frames.
5) Connect power cords to lights as shown.
Item
11
12
--
--
--
Qty.
1
1
1
2
4
Description
45.209”h Z45 Vertical Extrusion
37.209”h Z45 Vertical Extrusion
19.125”w x 86”h Lattice Light Curtain
38”w x 86”h Lattice Light Curtain
19.125”w x 90”h Lattice Light Curtain
Lattice Light Installation
Rotate clips on top & bottom
extrusions so that groove
faces back of frame.
Top extrusion
Bottom extrusion
BACK VIEW
clip
clip
Groove
Groove
1Lift up lattice light curtain
& insert ball chain into
groove of upper clips
Lights should face front of booth.
Top extrusion
Lattice Lights
clip Ball
chain
Groove
BACK VIEW
2
Lattice Lights
clip Loop
Hook loops
at bottom of
light curtain
over lower clips
Bottom extrusion
BACK VIEW
3
+
-
Power
Female
Transformer
144W / 6 Amp / 24V
Light to Transformer Attachment
When assembled
Z45 vertical
locks into
S10 extrusion
on center
top & bottom
clips.
Z45
S10
Transformer
Connection Lock
w/ Knob
*
BACK VIEW
Knobs face back of assembly.
*
*
11
12
*X
TransformerTransformer Transformer
Backwall Lights Installation
© 2023
Step 6 of 7
Order #XXXXX
Locked layer contains
placeholder marks.
BACK VIEW
Light Blocker Attachment
Assemble top & bottom rods. Insert rods through
top & bottom pockets
of light blocker.
Lift up light blocker.
Hook top rod over upper clips,
then hook bottom rod
over lower clips.
12
Shock Cord
Connection
3
BACK
VIEW
clip
clip
Steps:
1) Assemble rods & insert into top & bottom
pockets of light blockers as shown.
2) Hook rods over top & bottom clips on back
of assembled frames to secure light blockers
in place.
Item
--
--
--
--
Qty.
2
4
1
2
Description
Approx. 55”w x 5/16” collapsible rod
Approx. 110”w x 5/16” collapsible rod
109.242”w x 85.843”h Light Blocker
54.542”w x 89.843”h Light Blocker
Ligh
t
B
l
o
c
ker
Ligh
t
B
l
o
c
ker
Ligh
t
B
l
o
c
ker
Light Blocker Attachment
© 2023
Step 7 of 7
Order #XXXXX
Locked layer contains
placeholder marks.
Steps:
1) Apply SEG Graphics to assembled frames.
SEG Graphic Installation
Corner A
Corner D
Corner B
Corner C
It is important to first insert
graphic into each alternate
corner, then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab. Gently pull up on
the tab to remove the fabric.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
FRONT VIEW
S
E
G
Grap
h
ic
S
E
G
Grap
h
ic
S
E
G
Grap
h
ic
When assembled
Fabric Graphics Application
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Classic Exhibits SYK-2039 Setup Instructions

Type
Setup Instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI