Classic Exhibits SYK-2003 Setup Instructions

Classic Exhibits
Brand
Classic Exhibits
Model
SYK-2003
Type
Setup Instructions
© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
10’
20’
Perspective View
SYK-2003 - 10’ x 20’ Portable Display
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
REV 06/2023
© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq ft
Plan View
© 2023
Order #XXXXX
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, keep all
knobs & connectors attached to
extrusions during disassembly.
Part Identification - Numbering
7A
Engaged Lock
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
WARNING
General Information
© 2023
Order #XXXXX
TSP49 Profile
All knobs must be tightened securely to ensure a proper connection.
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Corner
Connector Corner
Connector
Corner
Connector
Corner
Connector
COMPLETED ASSEMBLY
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.
Straight Connection
3) Tighten all knobs to secure connection.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
Slide connector across seam of extrusions.
Tighten all knobs.
All knobs must be tightened securely to ensure a proper connection.
Straight Connector
2) Loosen all knobs, then slide straight
connector across the seam of extrusions.
Tool-less Frame Assembly
© 2023
Case 1 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1
(Bottom level)
Level 2 Level 3 Level 4 Level 5 Level 6
9
14
1 3 2 4
8,106,9
11 12
5 7
Monitor Mount
Setup Hardware
Counter
Top
Counter
Legs
Workstation
Graphic
Case Packing
© 2023
Case 2 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1
(Bottom level)
Level 2
1 35,6 2 4
7,8
Lights
Graphics
Literature
Trays
Case Packing
© 2023
Case 3 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1
(Bottom level)
Level 2 Level 3
1 35,6 2 4
7,8
9
13
Graphics
Case Packing
© 2023
Step 1 of 8
Order #XXXXX
Locked layer contains
placeholder marks.
TOP VIEW
Right Base Plate
*
*
When assembled
Item
1
2
3
4
5
6
7
8
9
9
10
11
12
14
Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Steps:
Refer to the Tool-less Frame Assembly general information page.
1) Assemble vertical extrusions [1-2], [3-4], [11-12] & horizontals [5-6-7], [8-9-10]
together, using Tool-less Spline Connectors labeled [X].
2) Connect vertical assemblies [1/2], [3/4] between horizontal
assemblies [5/6/7], [8/9/10], using Tool-less Corner Connectors labeled [A].
3) Install Base Plates [9] & [14] to bottom corners of frame assembly
as shown. See Left Base Plate Attachment & Right Base Plate Attachment details.
4) Lift frame to upright position, then connect vertical assembly [11/12] between
horizontal assemblies [5/6/7], [8/9/10] using Connection Lock w/ Knob.
Description
45”h TSP49 Vertical Extrusion
41”h TSP49 Vertical Extrusion
45”h TSP49 Vertical Extrusion
41”h TSP49 Vertical Extrusion
36.5”w TSP49 Horizontal Extrusion
36.5”w TSP49 Horizontal Extrusion
36.5”w TSP49 Horizontal Extrusion
36.5”w TSP49 Horizontal Extrusion
36.5”w TSP49 Horizontal Extrusion
6” x 22” End Base Plate w/ foot
36.5”w TSP49 Horizontal Extrusion
45.209”h Z45 Vertical Extrusion
37.209”h Z45 Vertical Extrusion
6” x 22” Base Plate w/ flange (right)
*
1
2
3
4
8
10
12
11
9
9
14
5
6
Connection Lock
w/ Knob
*
BACK VIEW
Knobs face back of assembly.
Tool-less Spline Connector
1. Place extrusions end-to-end.
2. Slide tool-less connectors
across seam of extrusions.
*
3. Tighten all knobs to secure connection.
Tool-less Corner Connector
1. Slide extrusion onto
Corner Connector.
2. Tighten all knobs to
secure connection.
*
Keep corner connectors attached to horizontal extrusions.
Assemble frame flat on ground.
7
FRONT VIEW
1) Place key hole over bolt on panel
& slide down.
2) Twist knob to secure connection.
Left Base Plate Attachment
*
key hole
bolt
Base Plate
knob threaded
hole
Right Base Plate Attachment
*
bolt
knob
Front
key hole
1) Place key hole over bolt
on panel & slide down.
2) Twist knob to secure
connection.
threaded
hole
Base Plate
*
*
X
*
X
*
X
A
*
A
*
A*
A
*
*
X
*X
*X
*
X
Large Backwall Frame Assembly (Left Frame)
© 2023
Step 2 of 8
Order #XXXXX
Locked layer contains
placeholder marks.
Item
1
2
3
4
5
6
7
8
Qty.
1
1
1
1
1
1
1
1
Description
45”h TSP49 Vertical Extrusion
45”h TSP49 Vertical Extrusion
45”h TSP49 Vertical Extrusion
45”h TSP49 Vertical Extrusion
27.35”w TSP49 Horizontal Extrusion
27.35”w TSP49 Horizontal Extrusion
27.35”w TSP49 Horizontal Extrusion
27.35”w TSP49 Horizontal Extrusion
When assembled
Tool-less Spline Connector
1. Place extrusions end-to-end.
2. Slide tool-less connectors
across seam of extrusions.
*
3. Tighten all knobs to secure connection.
Tool-less Corner Connector
1. Slide extrusion onto
Corner Connector.
2. Tighten all knobs to
secure connection.
*
Keep corner connectors attached to horizontal extrusions.
Assemble frame flat on ground.
Steps:
Refer to the Tool-less Frame Assembly general information page.
1) Assemble vertical extrusions [1-2], [3-4] & horizontal
extrusions [5-6], [7-8] together, using Tool-less Spline connectors labeled [X].
2) Connect vertical assemblies [1/2], [3/4] between horizontal
assemblies [5/6], [7/8], using Tool-less Corner Connectors labeled [A].
1
2
3
4
56
7
8
FRONT VIEW
*
X
A
*
A
*
A*
A
*
*
X
*X
*
X
Small Backwall Frame Assembly (middle frame)
© 2023
Step 3 of 8
Order #XXXXX
Locked layer contains
placeholder marks.
Item
1
2
3
4
5
6
7
8
9
13
Qty.
1
1
1
1
1
1
1
1
1
1
Description
45”h TSP49 Vertical Extrusion
45”h TSP49 Vertical Extrusion
45”h TSP49 Vertical Extrusion
45”h TSP49 Vertical Extrusion
27.35”w TSP49 Horizontal Extrusion
27.35”w TSP49 Horizontal Extrusion
27.35”w TSP49 Horizontal Extrusion
27.35”w TSP49 Horizontal Extrusion
6” x 22” End Base Plate w/ foot
6” x 22” Base Plate w/ flange (left) When assembled
Tool-less Spline Connector
1. Place extrusions end-to-end.
2. Slide tool-less connectors
across seam of extrusions.
*
3. Tighten all knobs to secure connection.
Tool-less Corner Connector
1. Slide extrusion onto
Corner Connector.
2. Tighten all knobs to
secure connection.
*
Keep corner connectors attached to horizontal extrusions.
Assemble frame flat on ground.
3
4
1
2
65
8
7
9
FRONT VIEW *
Steps:
Refer to the Tool-less Frame Assembly general information page.
1) Assemble vertical extrusions [1-2], [3-4] & horizontal
extrusions [5-6], [7-8] together, using Tool-less Spline connectors labeled [X].
2) Connect vertical assemblies [1/2], [3/4] between horizontal
assemblies [5/6], [7/8], using Tool-less Corner Connectors labeled [A].
3) Install Base Plates [9] & [13] to bottom corners of frame assembly
as shown. See Left Base Plate Attachment & Right Base Plate Attachment details.
*
13
1) Place key hole over bolt on panel
& slide down.
2) Twist knob to secure connection.
Right Base Plate Attachment
*
bolt
knob
Base Plate
threaded
hole
key hole
Left Base Plate Attachment
*
bolt
knob
Front
key hole
1) Place key hole over bolt
on panel & slide down.
2) Twist knob to secure
connection.
threaded
hole
Base Plate
TOP VIEW
Left Base Plate
*
X
A
*
A
*
A*
A
*
*
X
*X
*
X
Small Backwall Frame Assembly (right frame)
© 2023
Step 4 of 8
Order #XXXXX
Locked layer contains
placeholder marks.
*
Left Frame
Middle Frame
Right Frame
Steps:
1) Connect middle frame to base plates of
left & right frames, as shown.
See Base Plate Attachment detail.
When assembled
FRONT VIEW
1
2
3
4
3
4
3
4
*TOP VIEW
Base Plate
TOP VIEW
Base Plate
Base Plate Attachment
*
Place key hole over bolt on panel & slide down.
Twist knob to secure connection.
Front
Base Plate
key hole
bolt
Backwall Frames Connection
© 2023
Step 5 of 8
Order #XXXXX
Locked layer contains
placeholder marks.
Steps:
1) Apply SEG Graphics to assembled frames.
SEG Graphic Installation
Corner A
Corner D
Corner B
Corner C
It is important to first insert
graphic into each alternate
corner, then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab. Gently pull up on
the tab to remove the fabric.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
When assembled
FRONT VIEW
S
E
G
Grap
h
ic
S
E
G
Grap
h
ic
S
E
G
Grap
h
ic
Fabric Graphics Application
© 2023
Step 6 of 8
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Attach clamp of
stem light to top of
horizontal extrusion
where desired.
Twist knob on back
to tighten in place.
Light Attachment
*
knob
Light
BACK VIEW
Steps:
1) Attach Workstation Mounting Bracket
to backwall vertical as shown.
See Workstation Bracket Attachment detail.
2) Assemble Workstation legs & counter top to
bracket. See Workstation Assembly detail.
3) Attach Lights to top of backwall as shown.
See Light Attachment detail.
Light
*
Light
*
Light
*
Workstation
*
Extrusion
Hook the Mounting Bracket
over the vertical extrusion.
Slide
Bracket
forward
Slide down onto
V4 connector
Tighten knobs
to secure.
Mounting
Bracket
Workstation Bracket Attachment
Slide bracket forward, then
down onto V4 connector.
Tighten thumb screws to
secure connection to inside
of frame.
Bracket
TOP VIEW SIDE VIEW
123
V4
V4 connectors stay permanently
attached to vertical extrusion.
*
Threaded
Studs
Wing
nuts
Counter Top
Mounting
Bracket
Counter
Legs
UNDERSIDE VIEW
3) Attach power cords to
wireless chargers.
2) Connect Counter Top to
Mounting Bracket, using
wing nuts.
1) Attach threaded studs on underside
of Counter Top to Counter Legs;
secure with wing nuts.
Workstation Assembly
Keep cords attached to
underside of counter top.
Underside View of Counter
To Power
USB
charging
pad
power
cords
charging
block
Counter Top
Backwall Attachments
© 2023
Step 7 of 8
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Steps:
1) Attach Literature Trays to backwall vertical, as
shown. See Literature Tray Attachment detail.
Attach Literature Tray to
angled extrusion of bracket;
tighten knob to secure lock.
Slide bracket over
V4 connector on
vertical extrusion.
Tighten knobs of V4 connector
to secure bracket in place.
Extrusion
Bracket
Bracket
Literature Tray
Slide
Bracket
forward
TOP VIEW
123
Literature Tray Attachment
*
Tighten knob
to secure
lock.
SIDE VIEW
Bracket
Tighten knobs
V4 Slide down onto
V4 connector
V4 connectors stay permanently
attached to vertical extrusion.
Literature
Tray
*
Literature
Tray
*
Literature
Tray
*
Backwall Attachments (cont’d)
© 2023
Step 8 of 8
Order #XXXXX
Locked layer contains
placeholder marks.
Completed Assembly
Steps:
1) Attach Monitor Mount to backwall vertical.
See Monitor Mount Attachment detail.
*
Monitor
Mount
S
E
G
G
r
a
p
h
i
c
Bolts
Z45
Monitor Mount Attachment
*
Attach Monitor Mount back piece to
vertical extrusion using bolts & nuts.
Wing
nuts
Note: Monitor mounts install through SEG graphic.
Monitor Mount
Back piece
Slide monitor mount
into back piece.
Backwall Attachments (cont’d)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Classic Exhibits SYK-2003 Setup Instructions

Classic Exhibits
Brand
Classic Exhibits
Model
SYK-2003
Type
Setup Instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents