IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
SAVE THESE INSTRUCTIONSSAVE THESE INSTRUCTIONS
SAVE THESE INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS EXERCISE EQUIPMENT.
* Keep children off your bike at all times.
* When the bike is in use, young childred and pets should be kept at least 10 feet away.
* Use this bike only for its intended use as described in the manual.
* Keep your hands away from all moving parts, Never turn the pedal crank arms by hand.
* Do not remove your feet from the pedals while they are in motion.
* After exercising, push down on the tension knob or turn the tension knob in a clockwise
direction to slow the flywheel down and decrease the potential for injury.
* Do not dismount the bike until both the pedals and flywheel have come to a complete
stop.
* Do not attempt to use this bike at high speeds or in standing positions until you have
practiced and are comfortable at lower speeds.
* Rotate the tension konb clockwise to add resistance to the flywheel prior to standing
on the pedals.
* Never drop or insert any object into any opening on this bike.
* Do not use without proper footwear.
To assure that the safety level of this bike is maintained, examine components for wear
and tear on a regular basis. Components that are worn excessively or inoperable should
be replaced immediately or the bike should be put out of use until it is repaired.
Caution:
if you experience chest pains, nausea, dizziness or shortness of breath, stop exercising
immediately and consult your physician before continuing.
P-10M – INSTRUCTIONS FOR USE
1) The model P-10M bike is designed to be used as a group cycle in fitness studios and
health clubs. It has a fixed wheel driven flywheel and should only be used under
professional supervision.
2) Installation – it is important that the P-10M bike is correctly assembled and we recommend
that installation and assembly be carried out by suitably qualified personnel.
3) Handlebar and seat adjustment. It is important that the handlebar and seat are set at the height
correct for your body. Ask your instructor for assistance.
Adjusting the handlebar height - Make sure it is securely tightened and that there is no lateral or
vertical movement of the handlebar. Undo the Quick Release lever which is located in front of
main tube. Slide stem tube in upward or downward to the required height position then
re-tighten again .
Adjusting the seat height – refer to above mention.
The stem/sliding tube position can also be adjusted forwards or backwards. Undo the Quick Release
lever located underneath of the bottom of sliding tube .
Slide the handlebar/top sliding tube in forwards or backwards until reach the required position then
securely re-tighten the Quick Release lever.
The seat/slider position can also be adjusted forwards or backwards. Undo the Quick Release
lever located underneath of the bottom slider.
Slide the seat/top slider forwards or backwards until reach the required position then securely
re-tighten the Quick Release lever.
NOTE: there is a safety line engraved on the seat post and handlebar stem. On no
account should the seat post or handlebar stem ever be raised above this line.
4) Pedals and toestraps – your feet should be securely positioned in the toe clips during the
exercise. Put your foot as far forward as you can into the toe-clip and then pull the strap tight.
5) Resistance system- P-10M bike is with durable belt direct drive transmission system, to
adjust the exercising resistance on the completed spinning bike, undo the simply loosen or
tighten using control lever to make adjustment.
For emergency stop then push control lever up-ward to the hardest position for stopping the wheel.
6) The P-10M bike should operate on a level surface with no lateral movement.
There are height adjust pads located on either side underneath of front and rear ground tube .
7) Maintenance – like any other mechanical cycling device, the P-10M bike should be regularly
maintained. Ask your supplier for a detailed mantenance programme.
P-10M ASSEMBLY
Step 1 (foot)
Attach the front foot (7) to the frame using the bolt (3) and washer (4).
Step 2 (foot)
Attach the rear foot (2) to the frame using the bolt (3) and washer (4).
Step 3. (pedals)
attach the pedals (76R/76L) into the crank arms (70R/70L), each pedal
is marked with the letter R(right) or R(right) to denote the side of the bike
they are on. NOTE: the right hand crank is on the same side as the
chain cover (78R). Be careful to align the threads correctly to avoid any
damaged. A little grease on the thread should help the pedals to screw in
easily and correctly, tighten using a 15mm spanner, both pedals threads
should tighten towards the front of the bike.
STEP 1
STEP 2
STEP 3
Step 4. &5 (handlebar & stem) and Console assemble
Insert stem into frame main tube then adjust handlebar stem (16) to a proper position
then using lock lever (21) to fixed .
Open safety screw(73) on the stem sliding tube then insert handlebar(11) onto stem's
sliding tube , move handlebar forward or backward until at a propor position then
use sliding tube's lock lever(21) to fix it and screw back the safety screw(73) .
Assemble console with cable and fix it onto bracket :
Unscrew console's fixing screw (8) from the console .
Connect cable (92) with console(9) then fix console on the bracket by screw back
4 fixing screw (8) .
Note:Be careful on the cable(92) do not be damage during it connect with the console
to assemble on the bracket .
92
8
STEP 4
14
13
11
92
21
8
9
22
STEP 5
Step 6&7. (saddle & seat post)
Insert seat post (32) into frame's seat tube and move upward or downward until at
a propor position then use stem lock lever(21) to fix it .
Assembly saddle (23) on saddle top slider (30) , sliding saddle in forward or backward
until at a propor postioon then use lock lever (31) to fix it .
NOTE: Do not arise above safety line.
Step 8. (bottle cage)
Attach bottle cage(14) on handlebar bottle hold bracket then use 2 screw
(13) to fix bottle cage on the bracket by a 4mm allen key .
STEP 6
STEP 7
14
13
STEP 8
P - 10M PART LIST
NO. Unit
UnitUnit
Unit Q'ty
Q'tyQ'ty
Q'ty Remark
RemarkRemark
Remark
1Frame
FrameFrame
Frame KIT 1
2Rear Ground Tube 60*86*3T*545L
Rear Ground Tube 60*86*3T*545LRear Ground Tube 60*86*3T*545L
Rear Ground Tube 60*86*3T*545L PCS 1
3Bolt M10×P1.5×30L
Bolt M10×P1.5×30LBolt M10×P1.5×30L
Bolt M10×P1.5×30L PCS 4 CP
CPCP
CP
4Washer
WasherWasher
Washer ψ
ψψ
ψ22×
22×22×
22×ψ
ψψ
ψ10×2t
10×2t10×2t
10×2t PCS 4 CP
CPCP
CP
5Adjustable Foot Pad M10×P1.5
Adjustable Foot Pad M10×P1.5Adjustable Foot Pad M10×P1.5
Adjustable Foot Pad M10×P1.5 PCS 4
6Foot Tube's End Cap 60×86
Foot Tube's End Cap 60×86Foot Tube's End Cap 60×86
Foot Tube's End Cap 60×86 PCS 4
7Front Foot Tube 60×86×3t×545L
Front Foot Tube 60×86×3t×545LFront Foot Tube 60×86×3t×545L
Front Foot Tube 60×86×3t×545L PCS 1
8Screw M5×P0.8×10L Stainless
Screw M5×P0.8×10L StainlessScrew M5×P0.8×10L Stainless
Screw M5×P0.8×10L Stainless PCS 4
9Vortec #8109 Consol
Vortec #8109 Consol Vortec #8109 Consol
Vortec #8109 Consol PCS 1
10 Handlebar sliding tube's F/R sleeve
Handlebar sliding tube's F/R sleeveHandlebar sliding tube's F/R sleeve
Handlebar sliding tube's F/R sleeve PCS 2
11 Handlebar Set
Handlebar SetHandlebar Set
Handlebar Set KIT 1
12 "V" locking piece 23*23L
"V" locking piece 23*23L"V" locking piece 23*23L
"V" locking piece 23*23L PCS 1 Stainless
StainlessStainless
Stainless
13 Water Bottle Cage fix Screw M5×P0.8)
Water Bottle Cage fix Screw M5×P0.8)Water Bottle Cage fix Screw M5×P0.8)
Water Bottle Cage fix Screw M5×P0.8) PCS 2 Stainless
StainlessStainless
Stainless
14 Water Bottle Cage UL-127A
Water Bottle Cage UL-127AWater Bottle Cage UL-127A
Water Bottle Cage UL-127A PCS 1
15 Stem's sliding tube's plastic end cap
Stem's sliding tube's plastic end capStem's sliding tube's plastic end cap
Stem's sliding tube's plastic end cap PCS 1
16 Stem
StemStem
Stem KIT 1 Alloy
Alloy Alloy
Alloy
17 Main tube &seat tube's Sleeve
Main tube &seat tube's SleeveMain tube &seat tube's Sleeve
Main tube &seat tube's Sleeve PCS 2 BK
BKBK
BK
18 Main Tube's Seal Ring 40×97
Main Tube's Seal Ring 40×97 Main Tube's Seal Ring 40×97
Main Tube's Seal Ring 40×97 PCS 2 BK
BKBK
BK
19 "V" Lock piece
"V" Lock piece"V" Lock piece
"V" Lock piece ψ
ψψ
ψ23×24L
23×24L23×24L
23×24L PCS 2
20 Washer
WasherWasher
Washer ψ
ψψ
ψ22×
22×22×
22×ψ
ψψ
ψ10×2t
10×2t10×2t
10×2t PCS 2 CP
CPCP
CP
21 Main tube & S/T's Lock Lever
Main tube & S/T's Lock Lever Main tube & S/T's Lock Lever
Main tube & S/T's Lock Lever PCS 3 CP
CPCP
CP
22 Set Screw M6×P0.8×8L W/ Locktile
Set Screw M6×P0.8×8L W/ LocktileSet Screw M6×P0.8×8L W/ Locktile
Set Screw M6×P0.8×8L W/ Locktile PCS 3 CP
CPCP
CP
23 Saddle
SaddleSaddle
Saddle PCS 1
24 Seat post upper slider's End Cap
Seat post upper slider's End CapSeat post upper slider's End Cap
Seat post upper slider's End Cap PCS 1 BK
BKBK
BK
25 Seat Post Bottom Slider's End Cap
Seat Post Bottom Slider's End CapSeat Post Bottom Slider's End Cap
Seat Post Bottom Slider's End Cap PCS 1 BK
BKBK
BK
26 Stem Upper Slider's End Cap
Stem Upper Slider's End CapStem Upper Slider's End Cap
Stem Upper Slider's End Cap PCS 1 BK
BKBK
BK
27 Stem Bottom Slider's End Cap
Stem Bottom Slider's End CapStem Bottom Slider's End Cap
Stem Bottom Slider's End Cap PCS 1 BK
BKBK
BK
28 Screw M6×P1.0×10L
Screw M6×P1.0×10LScrew M6×P1.0×10L
Screw M6×P1.0×10L PCS 3 Stainless
StainlessStainless
Stainless
29 Floating piece
Floating piece Floating piece
Floating piece ψ
ψψ
ψ22×
22×22×
22×ψ
ψψ
ψ9.5×15
9.5×159.5×15
9.5×15 PCS 1 Stainless
StainlessStainless
Stainless
30 Rear top slider
Rear top sliderRear top slider
Rear top slider KIT 1 Alloy
Alloy Alloy
Alloy
31 Lock Lever M12×P1.75×22L×
Lock Lever M12×P1.75×22L×Lock Lever M12×P1.75×22L×
Lock Lever M12×P1.75×22L× ψ
ψψ
ψ8×10L
8×10L8×10L
8×10L PCS 1
32 Seat Post
Seat PostSeat Post
Seat Post KIT 1 Alloy
AlloyAlloy
Alloy
33 Fly Wheel Axle
Fly Wheel AxleFly Wheel Axle
Fly Wheel Axle ψ
ψψ
ψ25×
25×25×
25×ψ
ψψ
ψ20×155.5L
20×155.5L20×155.5L
20×155.5L PCS 1
34 Bearing 6004 ZZ SKF
Bearing 6004 ZZ SKFBearing 6004 ZZ SKF
Bearing 6004 ZZ SKF PCS 2
35 Cast Wheel
Cast WheelCast Wheel
Cast Wheel ψ
ψψ
ψ359.8×
359.8×359.8×
359.8× ψ
ψψ
ψ334.7×86t×5PK
334.7×86t×5PK334.7×86t×5PK
334.7×86t×5PK PCS 1
36 Alloy Ring
Alloy RingAlloy Ring
Alloy Ring ψ
ψψ
ψ450×
450×450×
450×ψ
ψψ
ψ360×16t
360×16t360×16t
360×16t PCS 1
37 Fly wheel axle's Sleeve
Fly wheel axle's SleeveFly wheel axle's Sleeve
Fly wheel axle's Sleeve ψ
ψψ
ψ24×
24×24×
24×ψ
ψψ
ψ20.1×56L
20.1×56L20.1×56L
20.1×56L PCS 1 CP
CPCP
CP
38 Nut M17×P1.0×8t
Nut M17×P1.0×8tNut M17×P1.0×8t
Nut M17×P1.0×8t PCS 2 CP
CPCP
CP
39 Screw M5×P0.8×10L
Screw M5×P0.8×10LScrew M5×P0.8×10L
Screw M5×P0.8×10L PCS 5 Black
BlackBlack
Black
40 Nut M12×P1.25×9t
Nut M12×P1.25×9tNut M12×P1.25×9t
Nut M12×P1.25×9t PCS 2 CP
CPCP
CP
Item/Description
Item/DescriptionItem/Description
Item/Description
NO. Unit
UnitUnit
Unit Q'ty
Q'tyQ'ty
Q'ty Remark
RemarkRemark
Remark
41 Washer
WasherWasher
Washer ψ
ψψ
ψ27×
27×27×
27×ψ
ψψ
ψ13×3t
13×3t13×3t
13×3t PCS 2 CP
CPCP
CP
42 Washer
WasherWasher
Washer ψ
ψψ
ψ10×
10×10×
10×ψ
ψψ
ψ6×1t
6×1t6×1t
6×1t PCS 4 UCP
UCPUCP
UCP
43 Bolt M6×P1.0×50L
Bolt M6×P1.0×50LBolt M6×P1.0×50L
Bolt M6×P1.0×50L PCS 2
44 Cover for Magnet's Bass:31×88.7×2t
Cover for Magnet's Bass:31×88.7×2tCover for Magnet's Bass:31×88.7×2t
Cover for Magnet's Bass:31×88.7×2t KIT 2
45 Magnet
MagnetMagnet
Magnet ψ
ψψ
ψ25×10t ,Identify
25×10t ,Identify25×10t ,Identify
25×10t ,Identify：+ -
：+ - ：+ -
：+ - pole .
pole .pole .
pole . PCS 6
46 Plastic Bass for Magnet Set
Plastic Bass for Magnet SetPlastic Bass for Magnet Set
Plastic Bass for Magnet Set KIT 1
47 Magnet's Set Inner Sleeve .
Magnet's Set Inner Sleeve .Magnet's Set Inner Sleeve .
Magnet's Set Inner Sleeve . PCS 1 Stainless
StainlessStainless
Stainless
48 Screw M6×P1.0×35L
Screw M6×P1.0×35LScrew M6×P1.0×35L
Screw M6×P1.0×35L PCS 1 Stainless
StainlessStainless
Stainless
49 Nut w/Nylon insert M6×P1.0
Nut w/Nylon insert M6×P1.0Nut w/Nylon insert M6×P1.0
Nut w/Nylon insert M6×P1.0 PCS 2 cp
cpcp
cp
50 Magnet's set Fix plate
Magnet's set Fix plate Magnet's set Fix plate
Magnet's set Fix plate PCS 1 Nylon
NylonNylon
Nylon
51 Sleeve
SleeveSleeve
Sleeve ψ
ψψ
ψ8×15L
8×15L8×15L
8×15L PCS 1 Stainless
StainlessStainless
Stainless
52 Screw M5×P0.8×6L
Screw M5×P0.8×6LScrew M5×P0.8×6L
Screw M5×P0.8×6L PCS 2 Stainless
StainlessStainless
Stainless
53 Cable connecting bar
Cable connecting barCable connecting bar
Cable connecting bar ψ
ψψ
ψ10×54 .
10×54 .10×54 .
10×54 . PCS 1 Stainless
StainlessStainless
Stainless
54 Pully
PullyPully
Pully ψ
ψψ
ψ18×
18×18×
18×ψ
ψψ
ψ9.5×13.7L
9.5×13.7L9.5×13.7L
9.5×13.7L PCS 1 UCP
UCPUCP
UCP
55 Spring fixing Axle
Spring fixing AxleSpring fixing Axle
Spring fixing Axle ψ
ψψ
ψ9×20L .
9×20L .9×20L .
9×20L . PCS 2 CP
CPCP
CP
56 Screw M5×P0.8×5L
Screw M5×P0.8×5LScrew M5×P0.8×5L
Screw M5×P0.8×5L PCS 4 CP
CPCP
CP
57 Rebound Spring .
Rebound Spring .Rebound Spring .
Rebound Spring . PCS 1
58 Screw M5×P0.8×15L
Screw M5×P0.8×15LScrew M5×P0.8×15L
Screw M5×P0.8×15L PCS 4 Stainless
StainlessStainless
Stainless
59 Adjusting wire for tune adjustment .
Adjusting wire for tune adjustment .Adjusting wire for tune adjustment .
Adjusting wire for tune adjustment . KIT 1
60 PUMoving Wheel
PUMoving WheelPUMoving Wheel
PUMoving Wheel ψ
ψψ
ψ76×24t×85A Hardness.
76×24t×85A Hardness.76×24t×85A Hardness.
76×24t×85A Hardness. PCS 2
61 Bearing 608ZZ
Bearing 608ZZ Bearing 608ZZ
Bearing 608ZZ PCS 4
62 Nut
NutNut
Nutψ
ψψ
ψ8×30L
8×30L8×30L
8×30L PCS 2 CP
CPCP
CP
63 Screw M6×P1.0×12L.
Screw M6×P1.0×12L.Screw M6×P1.0×12L.
Screw M6×P1.0×12L. PCS 2 CP
CPCP
CP
64 B.B Sleeve
B.B SleeveB.B Sleeve
B.B Sleeve ψ
ψψ
ψ24×
24×24×
24×ψ
ψψ
ψ20.1×23.1L
20.1×23.1L20.1×23.1L
20.1×23.1L PCS 1 UCP
UCPUCP
UCP
65 Bearing 6204 ZZ SKF
Bearing 6204 ZZ SKFBearing 6204 ZZ SKF
Bearing 6204 ZZ SKF PCS 2
66 Nut w/Nylon Insert M20×P1.0
Nut w/Nylon Insert M20×P1.0Nut w/Nylon Insert M20×P1.0
Nut w/Nylon Insert M20×P1.0 PCS 1 BK
BKBK
BK
67 B.B Axle
B.B AxleB.B Axle
B.B Axle ψ
ψψ
ψ25×
25×25×
25×ψ
ψψ
ψ20×141.5L .
20×141.5L .20×141.5L .
20×141.5L . PCS 1
68 Belt Pully
Belt PullyBelt Pully
Belt Pully ψ
ψψ
ψ265×5PK.
265×5PK.265×5PK.
265×5PK. PCS 1 BK
BKBK
BK
69 BB axle's Dusty Cover
BB axle's Dusty Cover BB axle's Dusty Cover
BB axle's Dusty Cover PCS 1 BK
BKBK
BK
70L Crank for Left side.
Crank for Left side.Crank for Left side.
Crank for Left side. PCS 1
70R Crank for Right Side .
Crank for Right Side .Crank for Right Side .
Crank for Right Side . PCS 1
71 Spring Washer
Spring WasherSpring Washer
Spring Washer ψ
ψψ
ψ10
1010
10 PCS 4 CP
CPCP
CP
72 Screw M10×P1.5×15L
Screw M10×P1.5×15LScrew M10×P1.5×15L
Screw M10×P1.5×15L PCS 4 Stainless
StainlessStainless
Stainless
73 Alen key bolt M5*P0.8*10L
Alen key bolt M5*P0.8*10LAlen key bolt M5*P0.8*10L
Alen key bolt M5*P0.8*10L PCS 1
74 Flange Nuty M10×P1.25×7t
Flange Nuty M10×P1.25×7tFlange Nuty M10×P1.25×7t
Flange Nuty M10×P1.25×7t PCS 2 BK
BKBK
BK
75 Dusty Cover
Dusty Cover Dusty Cover
Dusty Cover PCS 2 BK
BKBK
BK
76L LU-214 alloy body w/ toe clip& strap.
LU-214 alloy body w/ toe clip& strap.LU-214 alloy body w/ toe clip& strap.
LU-214 alloy body w/ toe clip& strap. PCS 1
76R LU-214 alloy body w/ toe clip& strap.
LU-214 alloy body w/ toe clip& strap.LU-214 alloy body w/ toe clip& strap.
LU-214 alloy body w/ toe clip& strap. PCS 1
77 Belt 5PK(1180)
Belt 5PK(1180)Belt 5PK(1180)
Belt 5PK(1180) PCS 1
78L Left Out Cover
Left Out CoverLeft Out Cover
Left Out Cover PCS 1 BK,ABS
BK,ABSBK,ABS
BK,ABS
78R Right Out Cover
Right Out CoverRight Out Cover
Right Out Cover PCS 1 BK,ABS
BK,ABSBK,ABS
BK,ABS
79 POP Cover
POP CoverPOP Cover
POP Cover PCS 2 TPR
TPRTPR
TPR
80 Screw M5×P0.8×10L
Screw M5×P0.8×10LScrew M5×P0.8×10L
Screw M5×P0.8×10L PCS 5 BK
BKBK
BK
Item/Description
Item/DescriptionItem/Description
Item/Description
NO. Unit
UnitUnit
Unit Q'ty
Q'tyQ'ty
Q'ty Remark
RemarkRemark
Remark
81 Battery cover
Battery coverBattery cover
Battery cover PCS 1 ABS
ABSABS
ABS
82 Screw M6×P1.0×10L
Screw M6×P1.0×10LScrew M6×P1.0×10L
Screw M6×P1.0×10L PCS 1 Stainless
StainlessStainless
Stainless
83 Screw M5×P0.8×15L
Screw M5×P0.8×15LScrew M5×P0.8×15L
Screw M5×P0.8×15L PCS 6 Stainless
StainlessStainless
Stainless
84 RV adjusting lever 3t
RV adjusting lever 3tRV adjusting lever 3t
RV adjusting lever 3t PCS 1 UCP
UCPUCP
UCP
85 Alen bolt M8×P1.25×20L
Alen bolt M8×P1.25×20LAlen bolt M8×P1.25×20L
Alen bolt M8×P1.25×20L PCS 1 UCP
UCPUCP
UCP
86 Adjustment's Bolt M6×9.5×31.7L
Adjustment's Bolt M6×9.5×31.7LAdjustment's Bolt M6×9.5×31.7L
Adjustment's Bolt M6×9.5×31.7L PCS 2 UCP
UCPUCP
UCP
87 Battery case
Battery caseBattery case
Battery case PCS 1 Plastic
PlasticPlastic
Plastic
87A
87A87A
87A Battery
BatteryBattery
Battery
pcs
pcs pcs
pcs
2
22
2
88 Nut w/Nylon Insert M6×P1.0
Nut w/Nylon Insert M6×P1.0Nut w/Nylon Insert M6×P1.0
Nut w/Nylon Insert M6×P1.0 PCS 1 CP
CPCP
CP
89 Washer
WasherWasher
Washer ψ
ψψ
ψ16×
16×16×
16×ψ
ψψ
ψ8.5×1.5t
8.5×1.5t8.5×1.5t
8.5×1.5t PCS 8 UCP
UCPUCP
UCP
90 Nut W/Nylon Insert M8×P1.25
Nut W/Nylon Insert M8×P1.25 Nut W/Nylon Insert M8×P1.25
Nut W/Nylon Insert M8×P1.25 PCS 3 UCP
UCPUCP
UCP
91 RV fix bracket 3t
RV fix bracket 3tRV fix bracket 3t
RV fix bracket 3t PCS 1 UCP
UCPUCP
UCP
92 Console's connect wire
Console's connect wireConsole's connect wire
Console's connect wire PCS 1 UCP
UCPUCP
UCP
93 Screw M8×P1.25×60L
Screw M8×P1.25×60LScrew M8×P1.25×60L
Screw M8×P1.25×60L PCS 2 UCP
UCPUCP
UCP
94 Inner Sleeve
Inner SleeveInner Sleeve
Inner Sleeve ψ
ψψ
ψ12×
12×12×
12×ψ
ψψ
ψ8.5×4t
8.5×4t8.5×4t
8.5×4t PCS 2 UCP
UCPUCP
UCP
95 VR w/cable
VR w/cableVR w/cable
VR w/cable PCS 1
96 KIT 4
97 pc 1
98 Adjusting wire
Adjusting wireAdjusting wire
Adjusting wire PCS 1
99 Screw M2.5*15L
Screw M2.5*15LScrew M2.5*15L
Screw M2.5*15L PCS 2 CP
CPCP
CP
100 Alen bolt M6*1.0*40L
Alen bolt M6*1.0*40LAlen bolt M6*1.0*40L
Alen bolt M6*1.0*40L PCS 1 CP
CPCP
CP
101 Washer 20*6.5*2t
Washer 20*6.5*2tWasher 20*6.5*2t
Washer 20*6.5*2t PCS 2 CP
CPCP
CP
102 Spring 4*9L*3
Spring 4*9L*3Spring 4*9L*3
Spring 4*9L*3 PCS 1 CP
CPCP
CP
103 lock pin 4*2.6*2*10L
lock pin 4*2.6*2*10Llock pin 4*2.6*2*10L
lock pin 4*2.6*2*10L PCS 1 CP
CPCP
CP
104 Cable roller's fixing washer
Cable roller's fixing washerCable roller's fixing washer
Cable roller's fixing washer PCS 2 UCP
UCPUCP
UCP
105 Left roller's fixing plate
Left roller's fixing plateLeft roller's fixing plate
Left roller's fixing plate PCS 1 UCP
UCPUCP
UCP
106 Cable pulling roller
Cable pulling rollerCable pulling roller
Cable pulling roller PCS 1 Blk
BlkBlk
Blk
107 Right roller's fixing plate
Right roller's fixing plate Right roller's fixing plate
Right roller's fixing plate PCS 1 UCP
UCPUCP
UCP
108 Screw M4×P0.7×8L
Screw M4×P0.7×8LScrew M4×P0.7×8L
Screw M4×P0.7×8L PCS 4 UCP
UCPUCP
UCP
109 Screw M3×10L
Screw M3×10LScrew M3×10L
Screw M3×10L PCS 4 UCP
UCPUCP
UCP
110L PCS 1 Plastic
PlasticPlastic
Plastic
110R
PCS 1 Plastic
PlasticPlastic
Plastic
111 Sensor fixing bracket for SR212
Sensor fixing bracket for SR212 Sensor fixing bracket for SR212
Sensor fixing bracket for SR212 PCS 1
112 Sensor w/Cable:
Sensor w/Cable:Sensor w/Cable:
Sensor w/Cable: ψ
ψψ
ψ6×300L×46mm(2PIN)
6×300L×46mm(2PIN)6×300L×46mm(2PIN)
6×300L×46mm(2PIN) PCS 1
113 Plastic end seal cover
Plastic end seal cover Plastic end seal cover
Plastic end seal cover pcs 2Plastic
PlasticPlastic
Plastic
114 Top tube's protector
Top tube's protector Top tube's protector
Top tube's protector PCS 1 Plastic
PlasticPlastic
Plastic
Resistanceright side adjusting lever
Resistanceright side adjusting leverResistanceright side adjusting lever
Resistanceright side adjusting lever
VR fix screw
VR fix screwVR fix screw
VR fix screw
sleeve 12*15,2*8L
sleeve 12*15,2*8Lsleeve 12*15,2*8L
sleeve 12*15,2*8L
Resistance left side adjusting lever
Resistance left side adjusting leverResistance left side adjusting lever
Resistance left side adjusting lever
Item/Description
Item/DescriptionItem/Description
Item/Description
P-10 Explode Diagrams
89 86
42
49
16
94
85
89 90
84
112
111
91
89
93
82
81
20
19
21
17
22
18
67
65
40
41
41
40
43
42
77 79
78R
80
11
92
80
76R
70R
68
72
71
74 75
66 65 64
70L
74
75
76L
31
32
98
17
18
19
20
21
28
25
30
23
24
27
29
28
26
114
21
8
9
46 45
45 52
44
44
51 52
59
56
55
88
57
54
47
58
53
56
48
58
50
10
22
83
80
80
95
96
97
99 102
106
101
107 108
109
110R 113
15
87
87A
22
69
12
49
73
100
103 104
105
101
3
4
10
89
110L
1
23
4
3
4
56
75
60 61
61
62 6
63
60 61
61
62
63
89 90
14
13
78L
80
79
37
34
38
36
35 39 34
33
/
