Australian Fitness V-V1200 User manual

Brand: Australian Fitness

Model: V-V1200

Type: User manual

BIKE V-V1200

MANUAL

V-V1200 INSTRUCTIONS FOR USE

1) The model V-V1200 is designed to be used as light commercial use or

or home use. It has a fixed wheel driven flywheel and should be used

under professional supervision. or asking your supplier before using.

2) Installation – it is important that the V-V1200 is correctly assembled and we recommend

that installation and assembly be carried out by suitably qualified personnel.

3) Handlebar and seat adjustment. It is important that the handlebar and seat are

set at the correct height for your body. Ask your instructor for assistance.

Adjusting the handlebar height - Make sure it is securely tightened and that there

is no lateral or vertical movement of the handlebar. Undo the Quick Release knob

which is located in front of head tube. Slide the handlebar/stem up or down to the

required height and then retighten.

The handlebar/stem position can also be adjusted forwards or backwards. Undo

the Quick Release lever located on below the slider. Slide the handlebar/stem

assembly forwards or backwards until you reach the required position. Then

securely re-tighten the Quick Release lever.

Adjusting the seat height – refer to above mention.

NOTE: there is a safety line engraved on the seat post. On no account

should the seat post ever be raised above this line.

4) Pedals and toestraps – your feet should be securely positioned in the toe clips

during the exercise. Put your foot as far forward as you can into the toe-clip and then pull the strap tight.

5) Resistance system- V-V1200 bike is with durable chain direct drive transmission system,

to adjust the exercising resistance on the completed bike, undo the simply loosen or tighten

using adjustment knob. Press down the brake lever for stopping the wheel.

6) The V-V1200 should operate on a level surface with no lateral movement.

There are height adjuster pads located on either side underneath the rear foot.

Turn these pads clockwise or anti-clockwise until the bike is totally stable on the ground.

7) Maintenance – like any other mechanical cycling device, the V-V1200 should be

regularly maintained. Ask your supplier for a detailed maintenance programme.

V-V1200 Assembly Diagrams

V-V1200 ASSEMBLY

Step 1 (foot)

Attach the front foot (6) to the frame using the bolt (3), washer (4) and nut (5).

Step 2 (foot)

Attach the rear foot (2) to the frame using the bolt (3), washer (4) and nut (5).

Step 3. (pedals)

attach the pedals (7R/7L) into the crank arms (62R/62L), each pedal

is marked with the letter R(right) or R(right) to denote the side of the bike

they are on. NOTE: the right hand crank is on the same side as the

chain cover (71). Be careful to align the threads correctly to avoid any damage.

A little grease on the thread should help the pedals to screw in easily

and correctly, tighten using a 15mm spanner, both pedals threads should

tighten towards the front of the bike.

Step 4. (handlebar & stem)

Attach handlebar (11) onto handle bar stem (19), silde handlebar (11) until reach

your required position. Using lock lever (17) for tightening. And then put the

handlebar-stem set onto front tube, adjust to your ideal position., and then

using lock lever to tighten. NOTE: Do not arise above safety line.

Step 5 (saddle & seat post)

Insert seat post (14) into frame's seat tube, assembly saddle (16) on

saddle top slider (16A). Adjust slider using lock lever (17) for forwards or backwards.

and then tighten until reach the proper position. Using lock lever (17)

adjust seat post (14) and tighten in proper position.

NOTE: Do not arise above safety line.

Step 6. 7. (bottle cage)

Attach screws (10) into bottle cage (9) on front fork in required position

using a 4mm allen key.

V-V1200 Diagrams

part no. description q'ty part no. description q'ty

Main Frame 1

Brake pad 1

Rear Ground Tube 1

Screw M6*P 1.0*20L 1

Groung Tube Fixed Bolt 4

Washer 13*6*1.5T 1

Washer 4

Nut M6*P1.0 1

Nut 4

Brake Arm 1

Front Ground Tube 1

Sleeve 10 OD*6.2*6.2L 1

Pedal 1

Spring 1.5D*4.5L 1

Nut M8*P1.25 2

Sleeve14D*14.9L 1

Bottle Cage 2

Bolt M6*P1.0*30 L 1

Bottle cages fixed screw 4

Adjustments Screw M6*P1.0*120L 2

Handle Bab 1

Washer 25OD*10ID*2T 2

Saddel clamp 1

Nut M10*P1.5 2

End plug for stem/post 6

PU Moving Wheel 64mm 2

Stem 1

Bolt 3/8"*16*15L 2

Seat Post 1

Bearing 608ZZ 4

Saddles Slider 1

Bolt nut 8*30L W/M6*P1.0 2

Saddle 1

Bolt nut M6*P1.0*12L 2

Lock Lever 4

Front Ground Tube End Cap 2

Lock Nut 23*23L 2

Belt 1

Screw M5*P1.0*8L 2

Sleeve 24OD*20.1ID*27L 1

V block 2

B.B Axle 25mm*20mm*116.5L 1

V Blocks Fixed Screw 4

62L

Left Crank 170L 1

Plastic Sleeve 8

62R

Right Crank 170L 1

Nylon sleeve 1

Flange Nut 2

Nut 3/8" x16TPI x 6t 1

Dusty Cover 2

Nut M20*1.0*12t 1

Bolt M10*P1.5*15L 4

Adjust Knob 1

Spring Washer 4

Moving Part 20 OD*34L 1

Pulley 210*5PK*20.5t 1

Lock Nut M8*P1.25 1

Inner blet Cover 1

Round Plate 20mm*3T 2

Screw M5*P0.8*10L 2

Spring 19mm*2.3mm*20L 1

Washer 10*5*1 T 2

Upper Stud 12.7 D*92L 1

Washer 16*6*2T 2

32A

Bottom Stud 12.7 D*28L 1

Outer blet cover 1

Guide Screw M8*P1.25*8L 1

Screw M5*p0.8*10L 5

Nut M6*P1.0 1

Screw M5*p0.8*15L 2

Spacer 24 OD*20.1 ID*51L 1

Adjustment screw 3/8”*16TPI*30L 2

Bearing 6004ZZ 2

Nut 3/8”*16TPI 2

Bearing 6004ZZ 2

Rear Ground Tube End Cap 2

Fly Wheels Axle 25*20*151 L 1

Fly Wheel 480*21kgs 1

Lock Nut M17*1.0*8T 2

V-V1200 Part List

Australian Fitness V-V1200 User manual

Brand: Australian Fitness

Model: V-V1200

Type: User manual

Download PDF

report

Australian Fitness V-V1200 User manual

Australian Fitness V-V1200 User manual

Other documents