Carrier 30XV50037401 Installation guide

Brand: Carrier

Model: 30XV50037401

Type: Installation guide

This manual is also suitable for

30XV140-500

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 04-53300179-01 Printed in U.S.A. Form 30XV-4SI Pg 1 6-17 Replaces: New

Installation Instructions

Part No. 30XV70000501, 30XV70000601

SAFETY CONSIDERATIONS

Installing, starting up, and servicing air-conditioning equip-

ment can be hazardous due to system pressures, electrical com-

ponents, and equipment locations.

Only trained, qualified installers and service technicians

should install, start up, and service this equipment.

When installing this accessory, observe precautions in the

literature and on any labels attached to the equipment, and all

other safety precautions that may apply.

• Follow all safety codes.

• Wear safety glasses and work gloves.

• Use care in handling and installing this accessory.

INTRODUCTION

The accessory condenser hail guard is designed to protect

the 30XV chillers from harsh weather conditions and debris.

See Table 1 for accessory package usage and see Table 2 for

accessory package contents.

Check each item for shipping damage. If any damage is

found, file a claim with the shipping agent immediately. If any

item is missing or if any part does not assemble properly, notify

your Carrier representative.

Field-Supplied Material — Zinc-rich paint.

Table 1 — 30XV Accessory Package Usage

*Standard, medium, or high tier is represented by an S, M, or H in

the 10th position of the unit model number.

CAUTION

To avoid the possibility of electrical shock, open and tag all

disconnects before installing this equipment. Be aware that

there may be more than one disconnect.

CAUTION

Only trained, qualified installers and service technicians

should install, start up, and service this equipment.

Untrained personnel can perform basic maintenance func-

tions such as cleaning coils. All other operations should be

performed by trained service personnel. When working on

the equipment, observe precautions in the literature and on

tags, stickers, and labels attached to the equipment.

CAUTION

To avoid damage to the refrigerant coils and electrical com-

ponents, use extreme care when drilling screw holes and

screwing in fasteners.

30XV UNIT SIZE

AND TIER*

NO. OF PACKAGE(S)

REQUIRED FOR

ACCESSORY PART NO.

30XV70000501 30XV70000601

140-Std 10

140-Mid 10

140-High 11

160-Std 10

160-Mid 11

160-High 12

180-Std 10

180-Mid 11

180-High 12

200-Std 11

200-Mid 12

200-High 13

225-Std 11

225-Mid 12

225-High 13

250-Std 12

250-Mid 13

250-High 14

275-Std 12

275-Mid 13

275-High 14

300-Std 13

300-Mid 14

300-High 15

325-Std 14

325-Mid 15

325-High 16

350-Std 14

350-Mid 15

350-High 16

400-Std 15

400-Mid 16

400-High 17

450-Std 16

450-Mid 17

450-High 18

500-Std 17

500-Mid 18

30XV140-500

Hail Guard Accessory

Table 2 — Accessory Contents

INSTALLATION

NOTE: Numbers in parentheses are item numbers unless

indicated.

NOTE: Not all panels in kit will be used for every unit size.

1. Disconnect all power to unit.

2. Attach side uprights (1) between each V section on both

sides of unit. Use 2 screws at the top and 2 at the bottom

of each upright. See Fig. 1.

3. Attach side channel assemblies (2 and 3) horizontally be-

tween uprights (1) on sides of chiller. Use channel assem-

bly (3) on the end sections and channel assembly (2) in

the other locations. Use 4 screws, 2 on each end of each

side channel assembly. See Fig. 2.

4. Attach the end channel assembly (4) horizontally to the

end of the unit opposite the control box. Use 4 screws,

2 on each end of the end channel assembly. See Fig. 3.

ACCESSORY PART NO. DESCRIPTION ITEM NO. QTY

30XV70000601

Side Upright, 30XV50061901 1 6

Side Channel Assembly, 30XV40042601 2 4

Side Channel Assembly, 30XV40042501 3 4

End Channel Assembly, 30XV40036701 4 1

Control Box Angle Support, 30XV40036801 5 1

Control Box Angle Support, 30XV40036901 6 1

Louvered Side End Panel, 30XV50062101 7 4

Louvered Side End Panel, 30XV50062103 8 4

Louvered Side Panel, 30XV50062001 9 4

Louvered Side Panel, 30XV50062002 10 4

Louvered End Panel, 30XV50037601 11 2

Louvered End Panel, 30XV50037602 12 2

End Wire Guard, 30XV50036802 13 1

Louvered End Panel, 30XV50037301 14 1

Louvered End Panel, 30XV50037401 15 1

Louvered End Panel, 30XV50037501 16 1

Screws, 00PPN500000304A 17 284

30XV70000701

Side Upright, 30XV50061901 1 2

Side Channel Assembly, 30XV40042601 2 2

Louvered Side Panel, 30XV50062001 9 2

Louvered Side Panel, 30XV50062002 10 2

Screws, 00PPN500000304A 17 80

IMPORTANT: Hail guard accessory is designed for installa-

tion after unit is installed. The upright and lower panels will

block the lifting points for the chiller.

Fig. 1 — Side Uprights

A30-6314

SIDE UPRIGHTSA30-6318

Fig. 2 — Side Channel Assemblies

SIDE END CHANNEL ASSEMBLIES

SIDE CHANNEL ASSEMBLIES

Fig. 3 — End Channel Assembly

END CHANNEL ASSEMBLY

A30-6319

a30-3619

5. Attach the control box angle support to the control box.

See Fig. 4.

NOTE: Use angle (5) and 2 screws for unit sizes 140 to

200 and angle (6) and 4 screws for unit sizes 225 to 325.

Neither support is required for unit sizes 350 to 500.

6. Attach side end panels (7 and 8) to sides of the unit near-

est the end at 4 corners using one screw at each clearance

hole in each panel. See Fig. 5.

NOTE: Item 7 is the top panel and Item 8 is the bottom

panel.

7. Attach side panels (9 and 10) to each side of the unit to

cover the area between the side end grilles. Use one screw

at each clearance hole in each panel. See Fig. 6.

NOTE: Item 9 is the top panel and Item 10 is the lower

panel.

8. Attach end panels (11 and 12) and end wire guard (13) to

the end of unit (opposite the control box). Attach panels

with one screw at each clearance hole in each panel. Place

screws between grille rods that are spaced closely togeth-

er. See Fig. 7.

Unit Sizes 140 to 200

a30-

6320

CONTROL BOX

ANGLE SUPPORT

Fig. 4 — Angle Supports

Unit Sizes 225 to 325

a30-6321

CONTROL BOX

ANGLE SUPPORT

A30-6321

Fig. 5 — Side End Panels

A30-6396

SIDE END CHANNEL ASSEMBLIES

SIDE CHANNEL ASSEMBLIES

Fig. 6 — Side Panels

SIDE PANELSA30-6318

A30-6397

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 04-53300179-01 Printed in U.S.A. Form 30XV-4SI Pg 4 6-17 Replaces: New

NOTE: Item 11 is the top panel and Item 12 is the lower

panel.

9. Piping may exit through the end grille or side grille de-

pending on the unit. Cut grille rods as required to provide

opening for water lines. Coat ends of cut rods with zinc-

rich paint to protect against rust.

10. Attach end panel(s) to the control box end of unit using

one screw at each clearance hole in each panel. See

Fig. 8.

NOTE: Use panel 14 for unit sizes 140 to 200 and panels

15 and 16 for unit sizes 225 to 325. Neither panel is re-

quired for unit sizes 350 to 500.

NOTE: Item 15 is the top panel and Item 16 is the bottom

panel.

11. When all panels are installed and properly fastened, re-

store power to unit.

Fig. 7 — Louvered End Panels and End Wire Guard

A30-6398

LOUVERED

END PANELS

END WIRE GUARD

Fig. 8 — Louvered End Panel 30XV140-325

CONTROL BOX

END PANEL(S)

Carrier 30XV50037401 Installation guide

Brand: Carrier

Model: 30XV50037401

Type: Installation guide

This manual is also suitable for

30XV140-500

Download PDF

report

Carrier 30XV50037401 Installation guide

This manual is also suitable for

Carrier 30XV50037401 Installation guide

Related papers

Other documents