Made In China
ASSEMBLY INSTRUCTIONS
BF-24686 PROVENCE SINGLE FILE CABINET
1/11
RIGHT
LEFT
A
DRAWER PANEL BOTTOM-1PCDRAWER PANEL BACK-1PC
DRAWER PANEL FRONT-1PC DRAWER PANEL SIDE-1PC DRAWER PANEL SIDE-1PC
BACK PANEL-1PC
JKL
IH
G
CAM-TOOL-1PC
RIGHT SIDE PANEL-1PCLEFT SIDE PANEL-1PC
BOTTOM PANEL-1PC
C
F
B
IMPORTANT NOTE:
model number and code letter of part(s) needed
ED
TOP PANEL-1PC
material carefully for small parts,which may have came loose inside the
Department.For efficient and speedy service please indicate the
Follow instructions listed below in proper sequence as
PARTS LIST
numbered to assure fast,easy and correct assembly.
missing or damaged,phone,fax,or mail to our Customer Service
compare with parts list to ensure all parts are present.If any parts are
carton during shipment. Count all parts and material hardware and
Thank you for purchasing this quality product.Be sure to check all packing
2/11
LEGS-4PCS
C1
B1
A1Z
HANGERS-4PCS
SCREWS-4PCS
SCREWS-4PCS
HOOKS-4PCS
CAM-LOCKS-8PCS
SCREWS-12PCS
Y
VWX
UT
S
P
Q
R
O
NM
ALLEN WRENCH-1PC
CAM-BOLTS-8PCS
SCREWS-8PCS SCREWS-12PCS
HANDLE-1PCSCREWS-2PCS
DOWELS-4PCS
FILE HANGERS-2PCS
OUTER SLIDES-2PCS
INNER SLIDES-2PCS
3/11
FEET-4PCS
D1
SCREWS-8PCS
4/11
NOTE:THE SURFACE WITH THE STICKER IS THE BACK SIDE.
E1 F1
MAT SLICES-8PCS
PLASTIC BELTS-2PCS
S
T
SAFETY RELEASE TAB
HOW TO SEPARATE GLIDES
5/11
SIMPLY PULL THE LEFT/RIGHT INNER GLIDES FROM THE OUTER GLIDES EXPOSING A SMALL
PRIOR TO ASSEMBLY,WE SUGGEST SEPARATING THE INNER GLIDES FROM THE OUTER-GLIDES,
BLACK SAFETY RELEASE TAB ,BY PUSHING THE SAFETY RELEASE TAB.YOU WILL BE ABLE TO
SEPARATE THE GLIDE
ARROW
ARE TIGHT, THE SHOULDER SHOULD BE
AGAINST THE SURFACE OF THE PART.
TURN THE CAM-BOLT SCREWS UNTIL THEY
AND DIRT THAT MAY HAVE SETTLED ONTO FINISH DURING SHIPMENT.IN ORDER
UPON OPENING THOROUGHLY CLEAN ALL WOOD SURFACES TO REMOVE DUST
TO PREVENT DAMAGE DURING ASSEMBLY,PLEASE ASSEMBLE THIS ITEM WITH AT
THE ARROWS ON THE HIDDEN CAM-LOCKS SHOULD POINT TO THE CAM-BOLTS
N
ARROW
NOTE:
6/11
M
LEAST TWO PEOPLE.
NOTE:
NOTE:
HOW TO USE THE CAM-TOOL
SHOULDER
U
Q
R
W
X
I
ATTACH THE HANDLE(X)INTO FRONT DRAWER PANEL(G)USING 2 SCREWS(W).
INSERT DRAWER PANEL BOTTOM(K)INTO SLOT IN SIDE DRAWER PANELS(H/I).
INSERT THE 2 DOWELS(U)INTO HOLES IN DRAWER PANEL BACK(J)AND ATTACH USING 4 SCREWS(Q).
INSERT THE FILE HANGERS(Y)INTO THE CUT-OUT OF DRAWER PANEL FRONT&BACK.
G
H
J
U
J
Q
Y
K
G
H
I
S
7/11
INSERT DOWELS(U)INTO HOLES IN PANEL(G)AND ATTACH SIDE PANELS(H/I)USING 4 SCREWS(Q).
ATTACH THE 2 INNER SLIDES(S)TO DRAWER PANEL SIDES(H/I)USING 6 SCREWS(R).
ATTACH OUTER SLIDES(T)TO SIDE PANELS(D/E)USING 6 SCREWS(R).
8/11
HOW TO USE THE ALLEN WRENCH
D1
P
O
E1
P
O
E1
B
C
T
D
R
E
D
E
N
M
A
B
E
D
N
M
ROTATE THE 4 CAM-BOLTS(M) INTO HOLES IN TOP PANEL(A).
ROTATE THE 4 CAM-BOLTS(M) INTO HOLES IN BOTTOM PANEL(B).
9/11
PLACE CAM-BOLTS(M) INTO HOLES IN PANELS(D/E)AND ATTACH USING 4 CAM-LOCKS(N).
PLACE CAM-BOLTS(M)INTO HOLES IN PANELS(D/E)AND ATTACH USING 4 CAM-LOCKS(N).
V
F
ATTACH 2 HOOKS(Z) USING 4 SCREWS(A1) IN THE PREDRILLED HOLES OF REAR TOP PANEL.
ATTACH THE BACK PANEL(F) USING 12 SCREWS(V).
INSERT THE DRAWER INNER SLIDES(S)TO OUTER SLIDES(T).
10/11
Z
A1
A1
Z
11/11
Z
Z
Z
C1
B1
F1
/
