HMDTALL
User guide
ULTRASONIC PORTABLE COOL
MIST HUMIDIFIER
USER GUIDE
About this guide
Before you start using the Macally HMDTALL,
be sure to read this guide in its entirety.
Package contents
• HMDTALL
• Micro USB cable
• 2 Filters (one in the filter chamber)
• User guide
Hardware basics
Action Button Actions
Safety intructions
Thank you for purchasing the Macally HMDTALL.
The Macally HMDTALL Ultrasonic Portable Cool
Mist Humidifier provides quick relief from dry air
making life pleasant for those with colds, allergies
and dry skin. The space-saving design, with an
easy-to-fill 6.7 oz tank and LED lighting makes it
ideal for use at work on your desk, or at home on
your nightstand. It disperses a fine mist into the air,
and is ultra-quiet making it ideal to have on while
you sleep. The humidifier is also equipped “Anti-Dry
technology” to prevent dry burning (turns off
automatically when the water level is low) and an
indicator light to let you know when it's time to refill
the water tank.
Please read the following carefully before using this
Macally product. Incorrect use of this product may
result in reduced performance, permanent
damage and void warranty:
1. Do not place this product near a heat source.
2. Operating temperature of -5°C to 40°C. Storage
temperature of -5°C to 40°C.
3. Do not place heavy objects on this product.
4. Do not drop this product.
5. Do not dispose this product in the garbage. Take
it to your local recycling centre.
Press and Release once
• First press - Start's continuous mist mode
• Second press - Changes the misting mode to 3
second intervals
• Third press - Turns the mist off
Press and Hold for 3 Seconds
• First press - Turns the LED's on in Aurora mode
• Second press - Pauses the Aurora effect and
locks in the current lighting color
• Third press - Turns the LED's off
Important notes
• Do not use any aroma scented oils or liquids with
this unit.
• Do not refill the tank by pouring water through
the top atomizing misting port of the humidifier.
• This humidifier is equipped with an Anti-Dry
probe which will cause the humidifier to shut down
automatically when the water level gets too low.
• The Anti-Dry probe relies on electrical
conductivity found in drinking water and since
purified water has a very low electrical conductivity
levels we do not recommend using purified water.
• To help extend the life of your humidifier please
use filtered water when possible.
• To clean the top Atomizing misting port, gently
rub the top surface with an ear swab and a little
rubbing alcohol.
Atomizing
Misting Port
LED Lighting
Anti-Dry
Probe
Filter Cover
Action Button
Water Level
Window
Water Filter
Micro USB cable
Micro
USB
Power
Port
Using the Humidifier
STARTING THE HUMIDIFIER
Twist off the humidifier lid
Fill the tank with water
Put the lid back on
*Do not use any aroma scented oils or liquids with
this unit.
"The humidifier has two missing options:
1. Continuous (default)
2. 3 second intervals"
To start the humidifier connect the Micro USB end
of the power cable to the back of the humidifier and
the USB end to any USB power adapter (adapter
not included)
Then press and release the action button to start
the humidifier in continuous mode (default). To
switch the mister to 3 second interval mode simply
press and release the action button a second time
and a 3rd time to turn it off.
Press and Release once
• First press - Start's continuous mist mode
• Second press - Changes the misting mode to 3
second intervals
• Third press - Turns the mist off
STARTING THE LED LIGHTING
REPLACING THE FILTER
Twist off the humidifier lid
Put the new filter into the filter opening of the
humidifier lid, pop the filter cover back into place
and reattach the humidifier lid.
1 2
1
2
3
4
Pull off the filter cover and take out the old filter.
*Note: There is spring located at the bottom of the
filter cover. Please put it back in if it should fall
out while replacing the filter.
"The humidifier has two LED options:
1. Aurora (default)
2. Solid"
To start the Aurora LED lighting effect simply press
and hold the action button for 3 seconds until the
light turns on. The LED lighting is set to Aurora
mode by default.
To pause the Aurora effect and lock in the current
lighting color simply press and hold the action
button a second time and a 3rd time to turn it off.
Press and Hold for 3 Seconds
• First press - Turns the LED's on in Aurora mode
• Second press - Pauses the Aurora effect and
locks in the current lighting color
• Third press - Turns the LED's off
Copyright © 2019 Macally Peripherals
Technical support
Warranty
Macally Peripherals warrants that this product will be free from defects
in title, materials and manufacturing workmanship for one year from
the date of the purchase. If the product is found to be defective then, as
your sole remedy and as the manufacturer’s only obligation, Macally
will repair or replace the product. This warranty is exclusive and is
limited to the Macally HMDTALL. This warranty shall not apply to
products that have been subjected to abuse, misuse, abnormal
electrical or environmental conditions, or any condition other than
what can be considered normal use. The liability of Macally Peripherals
arising from this warranty and sale shall be limited to a refund of the
purchase price. In no event shall Macally Peripherals be liable for costs
of procurement of substitute products or services, or for any lost prots,
or for any consequential, incidental, direct or indirect damages,
however caused and on any theory of liability, arising from this
warranty and sale. These limitations shall apply notwithstanding any
failure of essential purpose of any limited remedy.
For tech support please call +1 909 230 6888 or
e-mail us at [email protected]. Tech
support hours are from 8:30 AM to 5:30 PM
Monday through Friday (Pacific Standard Time).
/
