BLADEZ Milan Owner's manual

MILAN TREADMILL

OWNER’S MANUAL

BLADEZ FITNESS

BH North America Corporation

20155 Ellipse, Foothill Ranch, CA 92610

Phone: 949-206-0330

Fax: 949-206-0013

Email: fitness@bhnorthamerica.com

Web: www.bhnorthamerica.com and www.bhfitness.com

Issued: 20 August 2008 (v1)

MILAN TREADMILL

1

INTRODUCTION

Congratulations for selecting BLADEZ as your primary source of fitness. BLADEZ fitness equipment

offers many exercise programs that benefit users of all levels and ages. Your new machine is

designed to make your workouts more effective and enjoyable. Please read this entire manual

carefully before using your treadmill. This will allow you to get a full understanding of all the

features your BLADEZ’ machine provides. If you have any questions or concerns, please contact the

BLADEZ Corporation or any authorized BLADEZ FITNESS distributors in your area.

IMPORTANT SAFETY INSTRUCTIONS

User Safety

1. Users should pass a full medical examination before they begin an exercise program. Work at the

recommended exercise level. Do not over exert yourself. If you feel any pain or discomfort, stop

exercising immediately and consult your doctor.

2. Before exercising calculate your maximum heart rate using the formula shown in this manual.

3. Do warm up stretching exercises before using the unit.

4. Verify that all of the parts are attached and that the nuts, bolts, pedals and bar are correctly tightened

before use. Verify that there are not any cracks or sharp edges.

5. Do not wear loose clothing or high heels. Tie up shoe laces.

6. The maximum user weight is 350 pounds (159 Kg).

7. Keep hands away from moving parts.

8. Supervise children, invalids or disabled persons at all times. Children are curious and vulnerable to

accidents. Do not use the unit as a toy. Disabled people should not use the exercise equipment

without the assistance of a qualified person or doctor. Keep pets away from unit.

9. The owner is responsible for explaining safety instructions to each user.

10. The unit can only be used by one person at a time.

11. Wait for the unit to stop moving before stepping down.

12. Do not smoke or use fire near the equipment. Some of the plastic components are flammable.

13. Do not use the equipment in front of a burning stove and/or fireplace.

14. Persons suffering from a plastic allergy should consult their physician before using the equipment.

Unit Safety

1. For safety, maintain a minimum clearance around the unit. Maintain 18 inches on the front and on

each side of the unit plus 24 inches at the rear of the unit.

2. Always operate the unit with the safety switch (key) tether-cord securely affixed to your person

3. Install and use the unit on a flat, stable surface, with some type of protection for the floor or carpet. Do

not place it alongside walls or furniture. Check the unit before each use.

4. Please read all of the instructions before assembling or using this unit.

5. To reduce the dangers and risk of electric shock always unplug the unit from its electrical power

immediately after using, before cleaning, opening, disassembling or doing maintenance.

6. Do not place sharp objects near the exercise equipment.

7. Do not use the exercise equipment if it is not working correctly.

WARNING: To reduce the risk of fire, electric shock, injury to persons or inflicting the harm of a burn:

Please save these instructions.

MILAN TREADMILL

2

IMPORTANT SAFETY INSTRUCTIONS Continued

8. The unit should never be left unattended when plugged in. Unplug the unit from the electrical power

before leaving the room, when unused and before adding or removing parts.

9. Do not operate the unit under a blanket or pillow. Excessive heating can occur and cause fire, electric

shock, injury to persons or inflict the harm of a burn.

10. Use the unit only as described in this manual. Only use attachments recommended by the

manufacturer.

11. Never operate this unit if it has a damaged electrical cord or plug. Do not operate this unit if it is not

working properly. Do not operate this unit if it has been dropped or damaged. Do not operate this unit

if it has been immersed into water. Return the unit to a service center for examination and repair.

12. Do not pull or carry the unit by the electrical cord. Do not use the cord as a handle.

13. Keep the electrical cord away from heated surfaces.

14. Never operate the unit when the air openings are blocked. Keep the air openings free of lint, hair and

the like.

15. Do not drop or insert any objects into any openings.

16. Do not use outdoors or near water.

17. Do not operate where aerosol (spray) products are being used or where oxygen is being

administered.

Power Cord Safety & Grounding Instructions

This product is for use on a nominal 110-120-volt circuit and has a grounding plug that looks like the

plug illustrated in the figure. Make sure that the product is connected to an outlet having the same

configuration as the plug. No adapter or extension cord should be used with this product. Do not

change the plug in any way.

This product must be grounded. If it malfunctions or breaks down, grounding provides a path of least

resistance for electric currents, to reduce the risk of electric shock. This product is equipped with a cord

which has an equipment-grounding conductor and a grounding plug. The plug must be plugged into an

appropriate outlet that is properly installed and grounded in accordance with all local codes and

ordinances.

WARNING! – An improper connection of the equipment grounding conductor can result in a risk of an

electrical shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the

product is properly grounded. Do not modify the plug provided to you. If it does not fit the outlet, have a

proper outlet installed by a qualified electrician.

MILAN TREADMILL

3

PARTS LIST

No. Description Q’ty No. Description Q’ty

1 Base fame 1 50 End cap（Left） 1

2 Platform frame 1 51 End cap（Right） 1

3 Incline frame 1 52 Computer cover 1

4 Upright frame 2 53 Main overlay 1

5 Ezfit linking parts 2 54 LED overlay 1

6 Motor base frame 1 55 Accessory tray (left) 1

7 Computer frame 1 56 Accessory tray (right) 1

8 External extension tube frame 1 57 Bottle holder 2

9 Internal extension tube frame 1 58 Safety key 1

10 Running deck support 1 59 Hand pulse 2

11 Allen C.K.S half thread screwM10*65 1 60 Metal socket 1

12 Allen C.K.S half thread screwM10*50 4 61 Tube bushing 2

13 Allen C.K.S half thread screwM10*45 1 62 Tube plug 2

14 Allen C.K.S half thread screwM8*55 4 63 Foot cover 2

15 Allen C.K.S half thread screwM8*50 6 64 Upright lateral cover (left) 1

16 Allen C.K.S half thread screwM8*40 2 65 Upright lateral cover (right) 1

17 Allen C.K.S half thread screwM8*35 2 66 Motor base frame gasket (1) 2

18 Allen C.K.S full thread screwM8*20 8 67 Motor base frame gasket (2) 4

19 Allen socket head full thread screwM8*80 1 68 Back cover 1

20 Allen socket head full thread screwM8*75 2 69 Shock absorber (1) 4

21 Allen socket head full thread screwM8*30 2 70 Shock absorber (2) 2

22 Allen socket head full thread screwM8*10 4 71 Wheel 4

23 Hex full thread boltM8*50 1 72 Pop-pin knob 1

24 Hex full thread boltM8*40 1 73 Form tube 2

25 Hex full thread boltM8*20 2 74 Foot 4

26 Philips full thread screwM8*25 2 75 Cable right 1

27 Philips 沉头 full thread screwM6*25 6 76 Cable guide 3/8 1

28 Philips C.K.S full thread screwM5*20 3 77 Cable guide1/8 1

29 Philips C.K.S full thread screwM5*10 12 78 strape 8

30 Philips C.K.S full thread screwM4*10 13 79 Switch 1

31 Philips C.K.S self-tapping screw ST4*15 28 80 Rest switch 1

32 Philips C.K.S self-tapping screwST4*30 4 81 Controller 1

33 Philips C.K.S self-tapping screwST4*10 8 82 Power code 1

34 Philips self-tapping screw ST3*10 6 83 Speed sensor 1

35 Philips self-tapping screw ST4*15 8 84 Flat Washer Φ6*Φ20 6

36 Philips self-tapping screw ST3*10 2 85 Adaptor 1

37 Philips C.K.S steel tapping screw ST4*15 7 86 Motor 1

38 Flat washerΦ10 5 87 Incline motor 1

39 Flat washerΦ8 18 88 Running deck 1

40 Washer Φ5 1 89 Front roller 1

41 Curve washer Φ8 2 90 Rear roller 1

42 Self-fix bolt M10 6 91 Hydraulic 1

43 Self-fixing bolt M8 7 92 Transmission belt(HUTCHINSON) 1

44 Ferrite cover 4 93 Running belt 1

45 Lateral cover (left) 1 94 Ferrite 2

46 Motor cover 1 95 Cable ring 1

47 Lateral cover (left) 1 96 Upright tube guiding cable 1

48 Side rail 2 97 Main cable 1

49 Central side rail 2

MILAN TREADMILL

4

EXPLOSION DIAGRAM

MILAN TREADMILL

5

ASSEMBLY

Please read through these assembly instructions and familiarize yourself with each part of the treadmill

prior to commencing assembly. Always use two (2) people when moving and or assembling the treadmill

WARRANTY

MILAN TREADMILL

6

ASSEMBLY Continued

1. Lift the treadmill out of the carton and place on a flat floor.

Please pay extra attention not to turn any pivot points to prevent fingers from being pinched

2. Lift up the upright tube as the arrows show

Warning: Please be careful for pinch points

Fix upright tubes with 4 M8*50mm bolts

MILAN TREADMILL

7

ASSEMBLY Continued

3. Turn the computer as the drawing shows to proper position and fix the computer set with 2 wave

washers and 2 M8*20mm bolt on each side.

Warning: be careful to not pinch any wiring

Please fix tighten the bolts

4. Place the right and left upright lateral covers into upright tubes and fix on the base frame as the

drawing shows

MILAN TREADMILL

8

ASSEMBLY Continued

5. Fix the upright lateral covers with 4 ST4*15 screws on the base frame

For additional information on the operation of the computer console,

please contact Bladez Fitness.

Enjoy your new MILAN treadmill by Bladez Fitness

MILAN TREADMILL

9

CONSOLE INTRODUCTION

Console Display and Keys Description:

Described top to bottom, left to right

Display:

A: LCD (top and center) Program profile / graph / diagram

B: LED window (bottom left) Speed, program #

C: LED window (bottom center) Distance, Time, Calories

D: LED window (bottom right) Pulse, Incline

Keys:

Speed – Speed +

Quick Speed 1, 2, 4, 6, 8, 10 (miles per hour)

Program

Enter / Reset

Incline + Incline –

Quick Incline 1, 2, 4, 6, 8, 10, 12 (% incline)

Start (green)

Stop (red)

MILAN TREADMILL

10

CONSOLE INTRODUCTION Continued

Console Key Function

Described top to bottom, left to right

Speed – Press to decrease the speed of the walking belt

Speed + Press to increase the speed of the walking belt

Quick Speed 1, 2, 4, 6, 8, 10

Press these keys to change the speed of the belt to that specific mph

Program Press to view and select the various workout programs

P1 => P2 => P3 => P4 => P5 => P6 => P7 => P8

=> P9 => P10 => P11 => P12 => FAT test =>

Enter / Reset Press this key to

a) Select your workout goal Time, Calories or Distance

b) Reset the treadmill (press and hold for 5 seconds)

Incline – Press to decrease the incline of the machine

Incline + Press to increase the incline of the machine

Quick Incline 1, 2, 4, 6, 8, 10, 12

Press these keys to change the incline of the machine to that specific %

Start (green) Press to start the walking belt moving

Stop (red) Press to stop the walking belt from moving

COMPUTER PROGRAMS

Programs Description

Manual Program Normal mode (counting up of Time, Distance, Calorie)

Goal mode (counting down of Time, Distance or Calorie)

12 set programs P1, P2, P3, P4, P5, P6, P7, P8, P9, P10, P11, P12.

(see last page of manual for speed / incline parameters)

Body fat test

Program Operation

Manual Program – Normal

1) Attach the safety key clip to your clothing

2) Insert the safety key onto the computer board.

3) Press START key

4) The left LED window (speed/program) will show: 3 – 2 – 1. The unit will beep three times and the

belt will begin to move

5) Adjust your speed and incline as desired using the + , – or Quick keys

6) Press STOP during your workout if needed

7) Press START to restart

8) Pull the safety key off the console if you need to stop quickly. Reinsert and press START to restart

9) Press STOP once you have completed your workout

10) Remove the safety key from the treadmill when not in use

MILAN TREADMILL

11

COMPUTER PROGRAMS Continued

Manual Program – Goal

1) Attach the safety key clip to your clothing

2) Insert the safety key onto the computer board.

3) Press the PROGRAM key to select Time, Distance or Calories

Once your choice is flashing (Time, Distance ort calories), Press Enter / Reset

4) Enter your goal value

Time Default time goal is 30:00 Press + or – to adjust. The range is 5:00-99:00 minutes

Distance Default distance goal is 1.0M Press + or – to adjust. The range is 1.00-99.00 miles

Calories Default Calorie goal is 50.0 Press + or – to adjust. The range is 5-990

5) Press Start

6) The left LED window (speed/program) will show: 3 – 2 – 1, the unit will beep three times and the

belt will begin to move

7) Adjust your speed and incline as desired using the + , – or Quick keys

8) Press STOP during your workout if needed

9) Press START to restart

10) Pull the safety key off the console if you need to stop quickly. Reinsert and press START to

restart

11) Once you have reached your goal, the LCD display will show END and the unit will beep 10 times

12) Remove the safety key from the treadmill when not in use

Program 1 through 12

1) Attach the safety key clip to your clothing

2) Insert the safety key onto the computer board.

3) Press the PROGRAM to select the program of choice (P1 through P12)

4) Default time is 30:00 Press + or – to adjust. The range is 5:00-99:00 minutes

The program profile is divided into 16 parts. Each segment of the program profile is 1/16 of the total

time entered

5) Press START

6) The left LED window (speed/program) will show: 3 – 2 – 1, the unit will beep three times and the

belt will begin to move

7) Adjust your speed and incline as desired using the + , – or Quick keys

8) Press STOP during your workout if needed

9) Press START to restart

10) Pull the safety key off the console if you need to stop quickly. Reinsert and press START to

restart

11) Once you have reached your goal, the LCD display will show END and the unit will beep 10 times

12) Remove the safety key from the treadmill when not in use

MILAN TREADMILL

12

COMPUTER PROGRAMS Continued

Body Fat Program

1) Attach the safety key clip to your clothing

2) Insert the safety key onto the computer board.

3) Press the PROGRAM to select the Body Fat program. The LED display will show “s”

4) Enter your gender. Press Enter / Reset and the calorie window will show 01. The distance

window will show 01 for male or 02 for female. Press + or – keys to select your gender.

5) Enter your age. Press Enter / Reset and the calorie window will show 02. The distance window

will show 25 as the default age. Press + or – keys to adjust your age.

6) Enter your height. Press Enter / Reset and the calorie window will show 03. The distance window

will show 68 as the default height in inches. Press + or – keys to adjust your height.

7) Enter your weight. . Press Enter / Reset and the calorie window will show 04. The distance

window will show 154 as the default weight in pounds. Press + or – keys to adjust your weight.

8) Press Enter / Reset and the calorie window will show 05. The distance window will show 00 as the

body fat amount. Touch both hand pulse sensors (located on both the left and right handrails) and

wait for the unit to calculate your approximate body fat rate. This will take approximately 8 seconds.

Additional Functions / Notes

Incline function

The incline will remain at its last setting when the unit is stopped (by pressing STOP or removing the

safety key). Please be sure to reset it after each workout.

The incline must be set at 0% prior to attempting to fold the treadmill

Reset

To reset the panel, press the Enter / Reset key for 5 seconds

COMPUTER PARAMETERS

Numerical Range

Original Original value Designed range Display range

Time (min : sec) 0:00 30:00 5:00 - 99:00 0:00 – 99:59

Speed (Miles per Hour)

0.0 N/A N/A 0.6 - 10.0M/H

Incline (%) 00 N/A N/A 00 - 12

Distance (Miles) 0.00 1.00 1.00 - 99.00 0.0 - 99.99

Calories (approximate)

0 50 5 - 990 0.0 - 9999

MILAN TREADMILL

13

COMPUTER PARAMETERS Continued

Program Values

Programs 1 through 12

Segments 0 through 15 (16 total segments)

Speed mph

Incline %

P01 P02 P03 P04 P05 P06

NO

speed

Incline

speed

incline

speed

incline

speed

incline

speed

incline

speed

incline

0 0.6 0 0.6 0 0.6 0 0.6 0 0.6 0 0.6 0

1 1.8 1 1.2 1 1.8 0 1.8 5 1.8 0 3.1 2

2 1.8 2 3.1 2 3.1 2 3.1 5 4.3 4 4.3 2

3 4.3 3 3.1 2 4.3 2 3.1 5 0.6 4 1.8 0

4 3.1 4 4.3 3 5.6 4 4.3 5 1.2 0 4.3 3

5 3.1 5 4.3 3 5.6 4 4.3 5 4.3 0 5.6 3

6 5.6 6 5.6 2 6.8 3 5.6 4 5.6 3 1.8 0

7 3.1 6 3.1 2 8.1 3 5.6 4 0.6 3 4.3 4

8 3.1 4 3.1 3 8.1 3 5.6 4 1.8 0 6.8 4

9 3.1 4 3.1 3 8.1 3 6.8 4 2.5 0 3.1 0

10 5.6 4 1.8 2 6.8 4 6.8 4 6.8 2 4.3 5

11 5.6 4 1.8 2 5.6 3 8.1 3 0.6 2 8.1 5

12 5.6 5 5.6 3 4.3 2 8.1 3 1.8 0 1.8 0

13 3.1 3 5.6 2 3.1 1 8.1 2 4.3 0 3.1 6

14 1.8 3 3.1 2 1.8 1 3.1 2 8.1 1 8.1 6

15 0.6 0 1.2 0 0.6 0 1.8 0 3.1 0 4.3 0

P07 P08 P09 P10 P11 P12

NO

speed

incline

speed

incline

speed

incline

speed

incline

speed

incline

speed

incline

0 1.8 0 1.8 0 1.8 0 1.8 0 1.8 0 1.8 0

1 3.1 3 4.3 4 2.5 1 2.5 1 2.5 3 3.1 3

2 4.3 3 8.1 4 5.0 2 5.0 2 3.7 3 5.0 3

3 5.6 3 8.1 3 5.0 3 5.6 3 3.7 2 5.0 2

4 6.8 2 4.3 5 2.5 4 6.2 4 2.5 3 3.1 3

5 8.1 2 8.1 5 5.0 3 2.5 7 5.0 3 6.3 3

6 5.6 2 8.1 2 5.6 2 5.0 8 5.0 2 6.3 2

7 3.1 5 8.1 2 2.5 2 6.2 7 2.5 2 3.1 2

8 4.3 5 4.3 5 5.0 1 6.2 8 5.6 2 7.5 2

9 5.6 3 4.3 5 6.2 1 2.5 7 5.6 4 7.5 4

10 6.8 3 8.1 5 6.2 2 5.0 8 3.7 4 7.5 4

11 6.8 3 8.1 1 2.5 3 5.6 7 2.5 4 3.1 4

12 8.1 3 8.1 1 5.0 5 2.5 5 6.8 6 8.1 6

13 6.8 4 8.1 1 5.6 4 5.0 3 6.8 3 8.1 3

14 4.3 4 4.3 1 6.2 3 5.0 2 6.8 2 8.1 2

15 3.1 0 3.1 0 1.8 0 1.8 0 1.8 0 1.8 0

MILAN TREADMILL

14

North American Warranty

Warranties may vary in other countries. See your local Fitness Dealer.

WARRANTY SUBMITTAL

Please have the following information available when contacting your dealer or BH for warranty support.

• A copy of the dated purchase receipt or credit card statement.

• An explanation of the problem/malfunction or parts that are missing or damaged.

• Owner’s name, address and phone number.

• Model and Serial Number (when available).

Forward your information to BH North America by

FAX: (949) 206-0013

E-mail: fitness@bhnorthamerica.com

Mail to: 20155 Ellipse, Foothill Ranch, California 92610, USA

For troubleshooting assistance or to confirm your claim please phone:

(949) 206-8152

(800) 475-7899 (USA only)

(866) 325-2339 (USA & Canada)

BLADEZ FITNESS extends the following exclusive, limited warranty for this elliptical, which shall

apply only to the use of the device in the home, for residential, non-commercial purposes only.

Any other use of the device shall void this warranty.

FRAME & DRIVE MOTOR – Lifetime

BLADEZ Fitness warrants the Frame and Drive Motor against defects in workmanship and

materials for Lifetime, as long as it remains in the possession of the original owner.

ELECTRONICS & PARTS – 1 Year

BLADEZ Fitness warrants the Electronic components and all original parts against defects in

workmanship and materials for a period of one years from the date of original purchase, as long

as the device remains in the possession of the original owner.

LABOR – 1 Year

BLADEZ Fitness shall cover the labor cost for the repair of the device for a period of one year

from the date of original purchase, as long as the device remains in the possession of the

original owner. Labor warranty does not include the travel time and or expense that may result

from the unit being outside of the seller or repair technician’s normal service zone.

MILAN TREADMILL

15

WARRANTY continued

EXCLUSIVE REMEDY

The exclusive remedy for any of the above warranties shall be repair or replacement of defective

parts, or the supply of labor to cure any defect, provided that labor shall be limited to one year.

All labor shall be supplied by the local retailer and the product must be located within the

retailer’s service area. Labor warranty does not include the travel time and or expense that may

result from the unit being outside of the seller or repair technician’s normal service zone.

EXCLUSIONS AND LIMITATIONS

This warranty applies only to the original owner and is not transferable. This warranty is

expressly limited to the repair or replacement of a defective Frame, Electronic component, or

defective part and is the sole remedy of the warranty. The warranty does not cover normal wear

and tear.

BLADEZ FITNESS expressly disclaims all other warranties, express or implied, including but not

limited to all warranties of fitness for a particular purpose or of merchantability. This warranty

gives you specific legal rights and your rights may vary from state to state.

WARRANTY REGISTRATION

Your warranty card must be completed and sent to BLADEZ FITNESS before a warranty claim

can be processed.

BLADEZ Milan Owner's manual

BLADEZ Milan Owner's manual

Related papers

Other documents