Xilinx VCU110 User manual

February 2016

VCU110 Software Install

and Board Setup

XTP380

XILINX, the Xilinx logo, the Brand Window and other designated brands included herein are trademarks of Xilinx, Inc. All other trademarks are the property of

their respective owners.

NOTICE OF DISCLAIMER: The information disclosed to you hereunder (the “Information”) is provided “AS-IS” with no warranty of any kind, express or implied.

Xilinx does not assume any liability arising from your use of the Information. You are responsible for obtaining any rights you may require for your use of this

Information. Xilinx reserves the right to make changes, at any time, to the Information without notice and at its sole discretion. Xilinx assumes no obligation to

correct any errors contained in the Information or to advise you of any corrections or updates. Xilinx expressly disclaims any l iability in connection with technical

support or assistance that may be provided to you in connection with the Information. XILINX MAKES NO OTHER WARRANTIES, WHETHER EXPRESS,

IMPLIED, OR STATUTORY, REGARDING THE INFORMATION, INCLUDING ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR NONINFRINGEMENT OF THIRD-PARTY RIGHTS.

Revision History

Date Version Description

02/03/16 2.1 Added details on resetting Tera Term.

01/28/16 2.0 Updated for 2015.4 for ES3 Silicon.

11/20/15 1.2 Modified to match VCU110 Kit hardware.

10/22/15 1.1 Added ExaMax and Interlaken setup.

10/06/15 1.0 Initial version.

VCU110 Software Install and Board Setup

Xilinx VCU110 Board

Software Requirements

VCU110 Hardware Setup

UART Driver Install

Clock Setup

Ethernet Setup

Optional Hardware Setup

References

Note: This presentation applies to the VCU110

Xilinx VCU110 Board

Software Requirements

Xilinx Vivado Design Suite 2015.4, Design Edition with SDK

Note: Presentation applies to the VCU110

VCU110 Hardware Setup

Kit Hardware contents

– VCU110 Board

– One CFP4 Loopback

– One BullsEye cable (not

shown)

– Two XM107 FMC

Loopback boards

– Ethernet cable

– Two Micro USB cables

– 180 W Power supply (not

shown)

Note: Presentation applies to the VCU110

VCU110 Hardware Setup

CFP4 Loopback Adapter

– https://www.multilaneinc.com

– Part # ML4050

For the Board Interface Test, begin

with the CFP4 Loopback in slot MOD0

Note: Presentation applies to the VCU110

VCU110 Hardware Setup

Attach the two FMC XM107 boards to the FMC connectors, J2 and

J22

Note: Presentation applies to the VCU110

VCU110 Hardware Setup

Connect a USB Type-A to Micro-B

cable to the USB UART connector

(J4) on the VCU110 board

Connect a USB Type-A to Micro-B

cable to the USB JTAG (Digilent)

(J135) connector on the VCU110

board

Connect the Ethernet cable to P3

Connect these cables to your PC

Note: Presentation applies to the VCU110

VCU110 Hardware Setup

BullsEye Loopback Adapter

– www.avnet.com

– Part # HDR-155805-01-BEYE

Note: Presentation applies to the VCU110

VCU110 Hardware Setup

SMA Connector

– http://www.amphenolconnex.com

– Part # 132169

– Connect BullsEye cable:

– 003-005 and 004-006 (Link 3)

– 007-009 and 008-010 (Link 2)

– 011-013 and 012-014 (Link 1)

– 015-017 and 016-018 (Link 0)

Connect GTY Ref Clock to 175 MHz clock source (not included)

– Connect to BullsEye Clocks:

– 019 and 020 (GTY Ref Clock)

Note: Presentation applies to the VCU110

VCU110 Hardware Setup

BullsEye Loopback Adapter

– Elastomer must be installed

– Note the larger and smaller alignment pins

Note: Presentation applies to the VCU110

VCU110 Hardware Setup

BullsEye Loopback Adapter

– Attach to VCU110, observing the larger and smaller alignment pins

Note: Presentation applies to the VCU110

VCU110 Hardware Setup

Attach to J87, initially, for the Board Interface Test

Note: Presentation applies to the VCU110

VCU110 Hardware Setup

Connect the power supply to

the VCU110 (J15)

– Connect this power supply to a

power outlet

– Power on the VCU110 board for

the UART driver installation

Note: Presentation applies to the VCU110

VCU110 Hardware Setup

Watch your fingers around the fan when board is powered on

– Fan blades will break

– Fan model: Cofan F-7015HH12B

Note: Presentation applies to the VCU110

UART Driver Install

Install Si Labs CP210x USB UART Drivers

– Refer to UG1033 for details on installing the USB to UART Drivers

Note: Presentation applies to the VCU110

UART Driver Install

Determine the COM Port numbers for your system

Open the Device manager

Control Panel → System → Device Manager

– There will be two “Silicon Labs Dual CP210x” COM ports, Standard and

Enhanced

– The Standard COM Port is the FPGA UART COM Port

– The Enhanced COM Port is the System Controller COM Port

– The COM Port numbers will vary from system to system

These COM Port Numbers will be used in several of the tutorials

Note: Presentation applies to the VCU110

Terminal Setup

Refer to UG1036 regarding Tera Term installation

Board Power must be on before starting Tera Term

Start the Terminal Program and select the Enhanced USB Com Port

Note: See AR63771 regarding SDK Terminal Program

Terminal Setup

Set the baud to 115200

Note: Presentation applies to the VCU110

Page is loading ...

Xilinx VCU110 User manual

Xilinx VCU110 User manual

Related papers

Other documents