Gilson ASTM D4791 Operating instructions

Gilson
Brand
Gilson
Model
ASTM D4791
Type
Operating instructions

Gilson ASTM D4791 is a Four-Station Proportional Caliper designed to determine the relative shape characteristics of coarse aggregates. It can be used to classify particles as flat, elongated, or neither, based on their width-to-thickness and length-to-width ratios. The device is compliant with ASTM D4791 standards and requires minimal maintenance, involving periodic cleaning and oiling. With its ease of use and accurate measurements, the Gilson ASTM D4791 is a valuable tool for aggregate testing and quality control in construction and engineering applications.

Gilson ASTM D4791 is a Four-Station Proportional Caliper designed to determine the relative shape characteristics of coarse aggregates. It can be used to classify particles as flat, elongated, or neither, based on their width-to-thickness and length-to-width ratios. The device is compliant with ASTM D4791 standards and requires minimal maintenance, involving periodic cleaning and oiling. With its ease of use and accurate measurements, the Gilson ASTM D4791 is a valuable tool for aggregate testing and quality control in construction and engineering applications.

Rev: 06/15/2015
Four-Station Proportional Caliper
HM-38B
PHONE: 800-444-1508 P.O. Box 200, Lewis Center, Ohio 43035-0200 FAX: 800-255-5314
740-548-7298 E-mail: customerservice@gilsonco.com Website: www.globalgilson.com 740 -548-5314
OPERATING MANUAL
INTRODUCTION:
These instructions are a general guide for operation of this
device. The complete procedure for determination of relative
shape characteristics of coarse aggregates using the Four-
Station Caliper is described in ASTM D4791. The user should
carefully review the ASTM procedure before testing.
OPERATING INSTRUCTIONS:
Individual particles of aggregate of specific sieve sizes are
measured to determine the ratios of width to thickness and
length to width. The applied ratios are 1:2, 1:3, 1:4, and 1:5
according to desired specifications.
A. For Classification of Flat Particle Testing:
The user should set the larger opening of the Caliper
equal to the particle width. If the thickness of the same
particle can be placed within the smaller opening without
readjusting the Caliper, the particle is classified as Flat.
HM-38B
A. Test for Flatness B. Test for Elongation
(Continued on back.)
ASTM D4791
B. For Classification of Elongated Particle Testing:
The user should set the larger opening of the Caliper equal
to the particle length. If the width of the same particle can
be placed within the smaller opening without readjusting
the Caliper, the particle is classified as Elongated.
If the particle does not meet either classification of Flat or
Elongated, it is classified as Neither Flat nor Elongated.
DEFINITIONS:
Flat Particles — The particles having a ratio of width to thick-
ness greater than a specified value.
Elongated Particles — The particles having a ratio of length
to width greater than a specific value.
MAINTENANCE:
Very little maintenance is required for the Four-Station Caliper.
Clean the Caliper before each test to avoid foreign particles
which may effect results. Every six months add a drop of oil
into the ratio holes for smooth operation. Periodically, inspect
parts for wear to ensure compliance with ASTM D4791.
  • Page 1 1
  • Page 2 2

Gilson ASTM D4791 Operating instructions

Gilson
Brand
Gilson
Model
ASTM D4791
Type
Operating instructions

Gilson ASTM D4791 is a Four-Station Proportional Caliper designed to determine the relative shape characteristics of coarse aggregates. It can be used to classify particles as flat, elongated, or neither, based on their width-to-thickness and length-to-width ratios. The device is compliant with ASTM D4791 standards and requires minimal maintenance, involving periodic cleaning and oiling. With its ease of use and accurate measurements, the Gilson ASTM D4791 is a valuable tool for aggregate testing and quality control in construction and engineering applications.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents