Hitachi G 23SCY Handling Instructions Manual

Brand: Hitachi

Model: G 23SCY

Category: Power tools

Type: Handling Instructions Manual

This manual is also suitable for

Disc Grinder

Model G 18SCY

•

G 18SEY

G 18UBY

•

G 23SCY

G 23SEY

•

G 23UBY

Handling instructions

NOTE:

Before using this Electric Power Tool, carefully read through these

HANDLING INSTRUCTIONS to ensure efficient, safe operation. It

is recommended that these INSTRUCTIONS be kept readily

available as an important reference when using this power tool.

G23SEY

001Cover_G18SCY_Eng 7/18/07, 10:30 AM1

GENERAL SAFETY RULES

WARNING!

Read all instructions

Failure to follow all instructions listed below may result in

electric shock, fire and/or serious injury.

The term “power tool” in all of the warnings listed below

refers to your mains operated (corded) power tool or battery

operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

1) Work area

a) Keep work area clean and well lit.

Cluttered and dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust.

Power tools create sparks which may ignite the dust

of fumes.

c) Keep children and bystanders away while operating

a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodified plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol or medication.

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use safety equipment. Always wear eye protection.

Safety equipment such as dust mask, non-skid safety

shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch is in

the off position before plugging in.

Carrying power tools with your finger on the switch

or plugging in power tools that have the switch on

invites accidents.

d) Remove any adjusting key or wrench before turning

the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance

at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts.

Loose clothes, jewellery or long hair can be caught

in moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used.

Use of these devices can reduce dust related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power

tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not

turn it on and off.

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source before

making any adjustments, changing accessories, or

storing power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power

tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation.

If damaged, have the power tool repaired before

use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions and in the

manner intended for the particular type of power

tool, taking into account the working conditions

and the work to be performed.

Use of the power tool for operations different from

intended could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

PRECAUTION

Keep children and infirm persons away.

When not in use, tools should be stored out of reach

of children and infirm persons.

01Eng_G18SCY_Eng 7/18/07, 10:30 AM1

SPECIFICATIONS

*1 Be sure to check the nameplate on product as it is subject to change by areas.

*2 Weight: Only main body

*3 The starting current limiter produces the starting current to such an extent that a fuse (16A, slow-blow) is not

tripped.

STANDARD ACCESSORIES

(1) Wrench ........................................................................ 1

(2) Side handle ................................................................. 1

Depressed center wheels are not provided as standard

accessories.

Standard accessories are subject to change without

notice.

APPLICATIONS

䡬 Removal of casting fin and finishing of various types

of steel, bronze and aluminum materials and castings.

䡬 Grinding of welded sections or sections cut by means

of a cutting torch.

䡬 Grinding of synthetic resins, slate, brick, marble, etc.

䡬 Cutting of synthetic concrete, stone, brick, marble

and similar materials.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position. If

the plug is connected to a receptacle while the power

switch is in the ON position, the power tool will start

operating immediately, which could cause a serious

accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Fitting and adjusting the wheel guard

The wheel guard is a protective device to prevent

injury should the depressed center wheel shatter

during operation. Ensure that the guard is properly

fitted and fastened before commencing grinding

operation.

[Installing and adjusting the wheel guard]

䡬 Open the lever and insert the locating pin of wheel

guard, bringing it into line with the across flats of

packing ground.

䡬 Then, turn the wheel guard to a desired position (for

use).

䡬 Close the lever and fix it. If and when required, carry

out adjustments by tightening or loosening the screw.

䡬 If the lever does not move smoothly, apply some

lubricating oil to the sliding section between the set

piece and the lever.

䡬 Fasten the wheel guard at the position where the

across flats of the wheel guard positioning pin and

packing ground are aligned (the position where the

wheel guard is inserted), but do not use it.

Model G18SCY G18SEY G18UBY G23SCY G23SEY G23UBY

Voltage (by areas)*

(110V, 220V, 230V, 240V)

Input*

2400 W 2600 W 2400 W 2600 W

No-load speed 8500/min 6600/min

Outer dia. 180 mm 230 mm

Wheel Hole dia. 22 mm

Peripheral speed 80 m/s

Weight*

5.1 kg

Starting current limiter*

No No Yes No No Yes

PRECAUTIONS ON USING DISC GRINDER

1. Never operate these power tools without Wheel

Guards.

2. Check that speed marked on the wheel is equal to or

greater than the rated speed of the grinder.

Use only depressed center wheels rated at 80m/s or

more.

3. Ensure that the wheel dimensions are compatible

with the grinder and that the wheel fits the spindle.

4. Abrasive wheels shall be stored and handled with

care in accordance with manufacturer’s instructions.

5. Inspect the depressed center wheel before use, do

not use chipped, cracked or otherwise defective

products.

6. Always hold the body handle and side handle of the

power tool firmly. Otherwise the counterforce

produced may result in inaccurate and even

dangerous operation.

7. Do not use cutting-off wheels for side grinding.

8. Do not use of separate reducing bushings or adapters

to adapt large hole abrasive wheels.

9. The wheel continues to rotate after the tool is switched

off.

01Eng_G18SCY_Eng 7/18/07, 10:30 AM2

Fig. 1

5. Ensure that the depressed center wheel to be utilized

is the correct type and free of cracks or surface defects.

Also ensure that the depressed center wheel is

properly mounted and the wheel nut is securely

tightened, refer to the section on “Depressed Center

Wheel Assembly”.

6. Conducting a trial run

Ensure that the abrasive products is correctly mounted

and tightened before use and run the tool at no-load

for 30 seconds in a safe position, stop immediately if

there is considerable vibration or if other defects are

detected.

If this condition occurs, check the machine to

determine the cause.

7. Confirm the spindle lock mechanism

Confirm that the spindle lock is disengaged by pushing

push button two or three times before switching the

power tool on (See Fig. 3).

8. Fixing the side handle

Screw the side handle into the gear cover.

PRACTICAL GRINDER APPLICATION

1. Pressure

To prolong the life of the machine and ensure a first

class finish, it is important that the machine should

not be overloaded by applying too much pressure. In

most applications, the weight of the machine alone is

sufficient for effective grinding. Too much pressure

will result in reduced rotational speed, inferior surface

finish, and overloading which could reduce the life of

the machine.

2. Grinding angle

Do not apply the entire surface of the depressed

center wheel to the material to be ground. As shown

in Fig. 2, the machine should be held at an angle of

15° – 30° so that the external edge of the depressed

center wheel contacts the material at an optimum

angle.

Fig. 2

3. To prevent a new depressed center wheel from

digging into the workpiece, initial grinding should be

performed by drawing the grinder across the

workpiece toward the operator (Fig. 2 direction B).

Once the leading edge of the depressed center wheel

is properly abraded, grinding may be conducted in

either direction.

4. Switch operation

Switch ON: Push the locking button forward and

then press the switch lever.

* For continuous use, press the switch

lever. The switch lever is locked by

pushing the locking button forward

once again.

(*Subject to change depending on

area.)

Switch OFF: Press and release the switch lever.

5. Precautions immediately after finishing operation

After switching off the machine, do not put it down

until the depressed center wheel has come to a

complete stop. Apart from avoiding serious accidents,

this precaution will reduce the amount of dust and

swarf sucked into the machine.

CAUTION:

䡬 Check that the work piece is properly supported.

䡬 Ensure that ventilation openings are kept clear when

working in dusty conditions.

If it should become necessary to clear dust, first

disconnect the tool from the mains supply (use non-

metallic objects) and avoid damaging internal parts.

䡬 Ensure that sparks resulting from use do not create a

hazard e.g. do not hit persons, or ignite flammable

substances.

䡬 Always use eye and ear protection.

Other personal protective equipment such as dust

mask, gloves, helmet and apron should be worn

when necessary.

If in doubt, wear the protective equipment.

䡬 When the machine is not use, the power source

should be disconnected.

ASSEMBLING AND DISASSEMBLING THE

DEPRESSED CENTER WHEEL AND OTHER TOOLS

CAUTION:

Be sure to switch OFF and disconnect the attachment

plug from the receptacle to avoid a serious accident.

1. Assembling (Fig. 3)

(1) Turn the machine upside down so that the spindle is

facing upward.

(2) Mount the wheel washer onto the spindle.

(3) Fit the protruding part of the depressed center wheel

or cutting wheel or diamond wheel onto the wheel

washer.

Set piece

Locating pin

Lever

Screw

15 – 30°

01Eng_G18SCY_Eng 7/18/07, 10:30 AM3

Wrench

(4) Screw the wheel nut onto the spindle.

(For diamond wheel assembling, use the wheel nut

with the convex side against the diamond wheel.)

(5) Insert the push button to prevent rotation of the

spindle, and tighten the wheel nut with the accessory

wrench, as shown in Fig. 3.

2. Disassembling

Follow the above procedures in reverse.

CAUTION:

䡬 Comfirm that the depressed center wheel is mounted

firmly.

䡬 Confirm that the push button is disengaged by

pushing push button two or three times before

switching the power tool on.

MAINTENANCE AND INSPECTION

1. Inspecting the depressed center wheel

Ensure that the depressed center wheel is free of

cracks and surface defects.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Inspecting the carbon brushes

For your continued safety and electrical shock

protection, carbon brush inspection and replacement

on this tool should ONLY be performed by a Hitachi

Authorized Service Center.

4. Replacing supply cord

If the supply cord of Tool is damaged, the Tool must

be returned to Hitachi Authorized Service Center for

the cord to be replaced.

5. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool. Exercise due care to ensure the winding

does not become damaged and/or wet with oil or

water.

6. Service parts list

CAUTION:

Repair, modification and inspection of Hitachi Power

Tools must be carried out by an Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without

prior notice.

NOTE:

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

Wheel

nut

Brush cover

Socket for

side

handle

Push button

(Spindle lock)

Switch

Spindle

Side handle

Across flats

Wheel

washer

Diamond

wheel

Wheel

guard

Wheel

washer

Depressed

center

wheel

Wheel

nut

Wheel

nut

Cutting

wheel

Wheel

washer

Fig. 3

Lock button

01Eng_G18SCY_Eng 7/18/07, 10:30 AM4

G18SCY

Item

No.

Part Name Q’TY

SEAL LOCK HEX. SOCKET HD. BOLT M5

2 SPRING WASHER M5 2

TAPPING SCWER (W/FLANGE) D5

4 PUSHING BUTTON 1

5 SPRING 1

6 GEAR COVER ASS’Y 1

7 SPECIAL NUT M10 1

8 PINION 1

9 SEAL WASHER 1

10 FELT PACKING 1

11 BALL BEARING 6301DDCMPS2L 1

12 RUBBER RING (B) 1

13 BEARING COVER (A) 1

14 ARMATURE 1

15 FAN GUIDE 1

16 HEX. HD. TAPPING SCREW D5×75 2

17 STATOR 1

18 FELT WASHER 1

19 SIDE HANDLE 1

20 O-RING 1

21 LOCK PIN 1

22 GEAR ASS’Y 1

23 RETAINING RING FOR D10 SHAFT 1

24 COUPLING COVER 1

25 COUPLING DAMPER 4

26 COUPLING 1

27 GEAR 1

28 MACHINE SCREW M5×10 2

29 BEARING COVER (B) 1

30 BALL BEARING 6302DDCMPS2L 1

31 FELT PACKING (B) 1

32 SPINDLE 1

33 SEAL PLATE 1

34 PACKING GLAND 1

HEX. SOCKET HD. BOLT (W/FLANGE) M5×16

36 LABEL 1

37 SET PIN 1

38 LEVER 1

39 BOLT M8×22 1

40 SPRING WASHER M8 1

41 SET PIECE 1

RETAINING RING (E-TYPE) FOR D5 SHAFT

43 WHEEL GUARD ASS’Y 1

44 WHEEL WASHER (A) 1

45 D. C. WHEELS 180MM A24R 1

Item

No.

Part Name Q’TY

46 WHEEL NUT M14×21

47 DUST SEAL 1

48 BALL BEARING 6200VVCMPS2L 1

49 BEARING BUSHING 1

50 HOUSING 1

51 BRUSH COVER 1

52 HANDLE DAMPER 1

TAPPING SCREW (W/FLANGE) D4

54 CARBON BRUSH 7×17×22.5 2

55 BRUSH HOLDER SET 2

56 HANDLE (B) 1

57 BRUSH COVER 1

58 HITACHI LABEL 1

59 NAME PLATE 1

60 O-RING (I.D. 24.7) 1

61 O-RING (I.D. 31.2) 1

62 SWITCH 1

63 CORD CLIP 1

TAPPING SCREW (W/FLANGE) D4

65 SWITCH COVER 1

66 HANDLE (A) 1

67 TERMINAL M4.0 2

68 TUBE (D) 2

69 CORD ARMOR 1

70 CORD 1

501 WRENCH 1

02Back_G18SCY_Eng 7/18/07, 10:31 AM5

G18SEY

Item

No.

Part Name Q’TY

SEAL LOCK HEX. SOCKET HD. BOLT M5

2 SPRING WASHER M5 2

TAPPING SCWER (W/FLANGE) D5

4 PUSHING BUTTON 1

5 SPRING 1

6 GEAR COVER ASS’Y 1

7 SPECIAL NUT M10 1

8 PINION 1

9 SEAL WASHER 1

10 FELT PACKING 1

11 BALL BEARING 6301DDCMPS2L 1

12 RUBBER RING (B) 1

13 BEARING COVER (A) 1

14 ARMATURE 1

15 FAN GUIDE 1

16 HEX. HD. TAPPING SCREW D5×75 2

17 STATOR 1

18 FELT WASHER 1

19 SIDE HANDLE 1

20 O-RING 1

21 LOCK PIN 1

22 GEAR ASS’Y 1

23 RETAINING RING FOR D10 SHAFT 1

24 COUPLING COVER 1

25 COUPLING DAMPER 4

26 COUPLING 1

27 GEAR 1

28 MACHINE SCREW M5×10 2

29 BEARING COVER (B) 1

30 BALL BEARING 6302DDCMPS2L 1

31 FELT PACKING (B) 1

32 SPINDLE 1

33 SEAL PLATE 1

34 PACKING GLAND 1

HEX. SOCKET HD. BOLT (W/FLANGE) M5×16

36 LABEL 1

37 SET PIN 1

38 LEVER 1

39 BOLT M8×22 1

40 SPRING WASHER M8 1

41 SET PIECE 1

RETAINING RING (E-TYPE) FOR D5 SHAFT

43 WHEEL GUARD ASS’Y 1

44 WHEEL WASHER (A) 1

45 D. C. WHEELS 180MM A24R 1

Item

No.

Part Name Q’TY

46 WHEEL NUT M14×21

47 DUST SEAL 1

48 BALL BEARING 6200VVCMPS2L 1

49 BEARING BUSHING 1

50 HOUSING 1

51 BRUSH COVER 1

52 HANDLE DAMPER 1

TAPPING SCREW (W/FLANGE) D4×16

54 CARBON BRUSH 7×17×22.5 2

55 BRUSH HOLDER SET 2

56 HANDLE (B) 1

57 BRUSH COVER 1

58 HITACHI LABEL 1

59 NAME PLATE 1

60 O-RING (I.D. 24.7) 1

61 O-RING (I.D. 31.2) 1

62 SWITCH 1

63 CORD CLIP 1

TAPPING SCREW (W/FLANGE) D4×16

65 HANDLE (A) 1

66 TUBE (D) 2

67 CORD ARMOR 1

68 CORD 1

501 WRENCH 1

02Back_G18SCY_Eng 7/18/07, 10:31 AM6

G18UBY

Item

No.

Part Name Q’TY

SEAL LOCK HEX. SOCKET HD. BOLT

M5×14

TAPPING SCREW (W/FLANGE) D5

3 PUSHING BUTTON 1

4 SPRING 1

5 GEAR COVER ASS'Y 1

6 SPECIAL NUT M10 1

7 SEAL WASHER 1

8 FELT PACKING 1

9 BALL BEARING 6301VVCMPS2L 1

10 RUBBER RING (B) 1

11 BEARING COVER (A) 1

12 ARMATUR 1

13 FAN GUIDE 1

14 HEX. HD. TAPPING SCREW D5×75 2

15 STATOR 1

16 FELT WASHER 1

17 SIDE HANDLE 1

18 O-RING 1

19 LOCK PIN 1

20 GEAR AND PINION SET 1

21 RETAINING RING FOR D10 SHAFT 1

22 COUPLING COVER 1

23 COUPLING DAMPER 4

24 COUPLING 1

25 MACHINE SCREW M5×10 2

26 BEARING COVER (B) 1

27 BALL BEARING 6302VVCMPS2L 1

28 FELT PACKING (B) 1

29 SPINDLE 1

30 SEAL PLATE 1

31 PACKING GLAND 1

HEX. SOCKET HD. BOLT (W/FLANGE)

33 LABEL 1

34 SET PIN 1

35 LEVER 1

36 BOLT M8×22 1

37 SPRING WASHER M8 1

38 SET PIECE 1

RETAINING RING (E-TYPE) FOR D5

SHAFT

40 WHEEL GUARD ASS'Y 1

41 WHEEL WASHER (A) 1

42 D. C. WHEELS 180MM A24R 1

Item

No.

Part Name Q’TY

43 WHEEL NUT M14×21

44 DUST SEAL 1

45 BALL BEARING 6000VVCMPS2L 1

46 BEARING BUSHING 1

47 HOUSING ASS'Y 1

48 BRUSH COVER 1

49 HANDLE DAMPER 1

TAPPING SCREW (W/FLANGE) D4

51 CARBON BRUSH 7×17×22.5 1

52 BRUSH HOLDER SET 2

53 BRUSH COVER 1

54 HITACHI LABEL 1

55 NAME PLATE 1

56 O-RING 1

57 O-RING 1

58 RESISTOR 1

59 SWITCH 1

60 HANDLE (B) 1

61 CORD CLIP 1

TAPPING SCREW (W/FLANGE) D4

63 HANDLE (A) 1

64 TUBE (D) 2

65 CORD ARMOR D10.7 1

66 CORD 1

501 WRENCH 1

02Back_G18SCY_Eng 7/18/07, 10:31 AM7

G23SCY

Item

No.

Part Name Q’TY

SEAL LOCK HEX. SOCKET HD. BOLT

TAPPING SCREW (W/FLANGE) D5

3 PUSHING BUTTON 1

4 SPRING 1

5 GEAR COVER ASS'Y 1

6 SPECIAL NUT M10 1

7 SEAL WASHER 1

8 FELT PACKING 1

9 BALL BEARING 6301DDCMPS2L 1

10 RUBBER RING (B) 1

11 BEARING COVER (A) 1

12 ARMATURE ASS'Y 1

13 FAN GUIDE 1

14 HEX. HD. TAPPING SCREW D5×75 2

15 STATOR 1

16 FELT WASHER 1

17 SIDE HANDLE 1

18 O-RING 1

19 LOCK PIN 1

20 GEAR AND PINION SET 1

21 RETAINING RING FOR D10 SHAFT 1

22 COUPLING COVER 1

23 COUPLING DAMPER 4

24 COUPLING 1

25 MACHINE SCREW M5×10 2

26 BEARING COVER (B) 1

27 BALL BEARING 6302VVCMPS2L 1

28 FELT PACKING (B) 1

29 SPINDLE 1

30 SEAL PLATE 1

31 PACKING GLAND 1

HEX. SOCKET HD. BOLT (W/FLANGE)

33 LABEL 1

34 SET PIN 1

35 LEVER 1

36 BOLT M8×22 1

37 SPRING WASHER M8 1

38 SET PIECE 1

RETAINING RING (E-TYPE) FOR D5

SHAFT

40 WHEEL GUARD ASS'Y 1

41 WHEEL WASHER (A) 1

42 D. C. WHEELS 230MM A24R 1

Item

No.

Part Name Q’TY

43 WHEEL NUT M14×21

44 DUST SEAL 1

45 BALL BEARING 6000VVCMPS2L 1

46 BEARING BUSHING 1

47 HOUSING ASS'Y 1

48 BRUSH COVER 1

49 HANDLE DAMPER 1

TAPPING SCREW (W/FLANGE) D4

51 CARBON BRUSH 7×17×22.5 2

52 BRUSH HOLDER SET 2

53 BRUSH COVER 1

54 HITACHI LABEL 1

55 NAME PLATE 1

56 O-RING 1

57 O-RING 1

58 SWITCH 1

59 HANDLE (B) 1

60 CORD CLIP 1

TAPPING SCREW (W/FLANGE) D4

62 SWITCH COVER 1

63 HANDLE (A) 1

64 TERMINAL M4.0 2

65 TUBE (D) 2

66 CORD ARMOR 1

67 CORD 1

501 WRENCH 1

02Back_G18SCY_Eng 7/18/07, 10:31 AM8

G23SEY

Item

No.

Part Name Q’TY

SEAL LOCK HEX. SOCKET HD. BOLT M5

2 SPRING WASHER M5 2

TAPPING SCWER (W/FLANGE) D5

4 PUSHING BUTTON 1

5 SPRING 1

6 GEAR COVER ASS’Y 1

7 SPECIAL NUT M10 1

8 PINION 1

9 SEAL WASHER 1

10 FELT PACKING 1

11 BALL BEARING 6301DDCMPS2L 1

12 RUBBER RING (B) 1

13 BEARING COVER (A) 1

14 ARMATURE 1

15 FAN GUIDE 1

16 HEX. HD. TAPPING SCREW D5×75 2

17 STATOR 1

18 FELT WASHER 1

19 SIDE HANDLE 1

20 O-RING 1

21 LOCK PIN 1

22 GEAR ASS’Y 1

23 RETAINING RING FOR D10 SHAFT 1

24 COUPLING COVER 1

25 COUPLING DAMPER 4

26 COUPLING 1

27 GEAR 1

28 MACHINE SCREW M5×10 2

29 BEARING COVER (B) 1

30 BALL BEARING 6302DDCMPS2L 1

31 FELT PACKING (B) 1

32 SPINDLE 1

33 SEAL PLATE 1

34 PACKING GLAND 1

HEX. SOCKET HD. BOLT (W/FLANGE) M5×16

36 LABEL 1

37 SET PIN 1

38 LEVER 1

39 BOLT M8×22 1

40 SPRING WASHER M8 1

41 SET PIECE 1

RETAINING RING (E-TYPE) FOR D5 SHAFT

43 WHEEL GUARD ASS’Y 1

44 WHEEL WASHER (A) 1

45 D. C. WHEELS 230MM A24R 1

Item

No.

Part Name Q’TY

46 WHEEL NUT M14×21

47 DUST SEAL 1

48 BALL BEARING 6200VVCMPS2L 1

49 BEARING BUSHING 1

50 HOUSING 1

51 BRUSH COVER 1

52 HANDLE DAMPER 1

TAPPING SCREW (W/FLANGE) D4×16

54 CARBON BRUSH 7×17×22.5 2

55 BRUSH HOLDER SET 2

56 HANDLE (B) 1

57 BRUSH COVER 1

58 HITACHI LABEL 1

59 NAME PLATE 1

60 O-RING (I.D. 24.7) 1

61 O-RING (I.D. 31.2) 1

62 SWITCH 1

63 CORD CLIP 1

TAPPING SCREW (W/FLANGE) D4×16

65 HANDLE (A) 1

66 TERMINAL M4.0 2

67 CORD ARMOR 1

68 CORD 1

501 WRENCH 1

02Back_G18SCY_Eng 7/18/07, 10:31 AM9

G23UBY

Item

No.

Part Name Q’TY

SEAL LOCK HEX. SOCKET HD. BOLT M5

2 SPRING WASHER M5 2

TAPPING SCWER (W/FLANGE) D5

4 PUSHING BUTTON 1

5 SPRING 1

6 GEAR COVER ASS’Y 1

7 SPECIAL NUT M10 1

8 PINION 1

9 SEAL WASHER 1

10 FELT PACKING 1

11 BALL BEARING 6301DDCMPS2L 1

12 RUBBER RING (B) 1

13 BEARING COVER (A) 1

14 ARMATURE 1

15 FAN GUIDE 1

HEX. HD. TAPPING SCREW D5×75

17 STATOR 1

18 FELT WASHER 1

19 SIDE HANDLE 1

20 O-RING 1

21 LOCK PIN 1

22 GEAR ASS’Y 1

RETAINING RING FOR D10 SHAFT

24 COUPLING COVER 1

25 COUPLING DAMPER 4

26 COUPLING 1

27 GEAR 1

28 MACHINE SCREW M5

10 2

29 BEARING COVER (B) 1

30 BALL BEARING 6302DDCMPS2L 1

31 FELT PACKING (B) 1

32 SPINDLE 1

33 SEAL PLATE 1

34 PACKING GLAND 1

HEX. SOCKET HD. BOLT (W/FLANGE) M5

36 LABEL 1

37 SET PIN 1

38 LEVER 1

39 BOLT M8

22 1

40 SPRING WASHER M8 1

41 SET PIECE 1

RETAINING RING (E-TYPE) FOR D5 SHAFT

43 WHEEL GUARD ASS’Y 1

44 WHEEL WASHER (A) 1

45 D. C. WHEELS 230MM A24R 1

Item

No.

Part Name Q’TY

46 WHEEL NUT M14

47 DUST SEAL 1

48 BALL BEARING 6200VVCMPS2L 1

49 BEARING BUSHING 1

50 HOUSING 1

51 BRUSH COVER 1

52 HANDLE DAMPER 1

TAPPING SCREW (W/FLANGE) D4

54 CARBON BRUSH 7×17

22.5 2

55 BRUSH HOLDER SET 2

56 HANDLE (B) 1

57 BRUSH COVER 1

58 HITACHI LABEL 1

59 NAME PLATE 1

60 O-RING (I.D. 24.7) 1

61 O-RING (I.D. 31.2) 1

62 RESISTOR 1

63 SWITCH 1

64 CORD CLIP 1

TAPPING SCREW (W/FLANGE) D4

66 HANDLE (A) 1

67 TUBE (D) 2

68 CORD ARMOR 1

69 CORD 1

501 WRENCH 1

02Back_G18SCY_Eng 7/18/07, 10:31 AM10

709

Code No. C99155212

Printed in Malaysia

Hitachi Koki Co., Ltd.

001Cover_G18SCY_Eng 7/18/07, 10:30 AM2

Hitachi G 23SCY Handling Instructions Manual

Brand: Hitachi

Model: G 23SCY

Category: Power tools

Type: Handling Instructions Manual

This manual is also suitable for

Download PDF

report

Hitachi G 23SCY Handling Instructions Manual

This manual is also suitable for

Hitachi G 23SCY Handling Instructions Manual

Related papers

Other documents