IS-52229-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
CLEANING:
Always be certain that electric current is turned o before
cleaning.
• Only a so damp cloth should be used. Harsh cleaning
products may damage the nish.
[A] Mounting
Strap
[B] Outlet Box
[C] Mounting
Screws
[D] Canopy
[E] Strap
Mounting
Screws
[F] Spacer
[G] Bulb
[H] Glass
[I] Socket Ring
[J] Bulb Cover
[K] Spanner Tool
1) Aach mounng strap[A] to outlet box[B] using the
strap mounng screws[E]. Mounng strap can be
adjusted to suit posion of xture.
2) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, and thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector aer following the above steps. Never connect
ground wire to black or white power supply wires.
3) Make wire connecons. Reference chart below for
correct connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
4) Push xture to wall carefully aligning the mounng
screw holes in the top and boom of the mounng strap
with mounng screw holes in the top and boom of
the canopy. NOTE: Fixture can be mounted with glass in
the up or down posion. Make sure all wires are inside
canopy and do not get pinched between canopy and
wall.
5) Screw in two (2) mounng screws[C]: one on top side of
canopy and one on boom side of canopy[D].
6) Carefully place the glass[H] over the socket to the
xture. Slip the smaller opening over the socket and t
the glass against the socket.
7) Place the spacer[F] over the socket and using the
spanner tool[K] thread the socket ring[I] onto the
socket. Tighten socket ring to secure glass in place. (DO
NOT over ghten). Do not discard the spanner wrench,
keep for future use if glass needs to be removed.
8) Insert recommended halogen bulb[G] (supplied). (Note:
Do not handle the bulb with bare hands).
9) Install bulb cover[J] over the installed bulb by twisng
into place, do not over ghten.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Installaon Instrucons
H
B
A
C
D
E
I
G
J
K
F
