1) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
2) Thread hexnut onto threaded pipe so that 5 threads are
exposed below hexnut. From underside of mounting strap,
thread long end of threaded pipe into hole in mounting strap
until hexnut touches mounting strap. Tighten hexnut against
mounting strap.
3) Thread second hexnut onto other end of threaded pipe.
Tighten hexnut up against mounting strap.
4) Attach mounting strap to outlet box. (Screws not provided)
5) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a hole
and two raise dimples. Wrap ground wire from outlet
box around green ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
(Not provided.) After following the above steps. Never connect
ground wire to black or white power supply wires.
6) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
7) Push fixture to wall, carefully passing threaded pipe through
hole in canopy.
8) Screw threaded cap onto threaded pipe. Tighten threaded
cap to secure fixture to wall.
9) Insert recommended bulbs.
10) Raise glass up to fixture. Pass hole in glass over bulb. Fit
top edge of glass inside cap on fixture.
11) Fit one bracket around indentation in glass. Align holes on
each end of bracket with holes at end of each arm on fixture.
12) Fit second bracket around indentation in glass. Align hole on
each end of bracket with holes at end of each arm on fixture
and holes in first bracket.
13) Slip end of one ball stud through holes in brackets and arm.
14) Thread ball knob onto end of ball stud protruding from hole
in bracket.
15) Repeats steps 13 and 14 for remaining ball stud and ball
knob.
16) Tighten both ball knobs to secure brackets in place.
Date Issued: 5/9/14 IS-45576-US
MOUNTING STRAP
PLANCHA PARA
MONTAR
FIXTURE
ARTEFACTO
GLASS
VIDRIO
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
THREADED CAP
TAPA ROSCADO
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
THREADED
PIPE
TUBO
ROSCADO
CAP
TAPA
ARM
BRAZO
BRACKET
MÉNSULA
BALL STUD
PERNO
ESFÉRICO
BALL KNOB
PERILLA
ESFÉRICA
HEXNUT
TUERCA
HEXAGONAL
Page is loading ...
1) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
2) Thread hexnut onto threaded pipe so that 5 threads are
exposed below hexnut. From underside of mounting strap,
thread long end of threaded pipe into hole in mounting strap
until hexnut touches mounting strap. Tighten hexnut against
mounting strap.
3) Thread second hexnut onto other end of threaded pipe.
Tighten hexnut up against mounting strap.
4) Attach mounting strap to outlet box. (Screws not provided)
5) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
6) Push fixture to wall, carefully passing threaded pipe through
hole in canopy.
7) Screw threaded cap onto threaded pipe. Tighten threaded
cap to secure fixture to wall.
8) Insert recommended bulbs.
9) Raise glass up to fixture. Pass hole in glass over bulb. Fit
top edge of glass inside cap on fixture.
10) Fit one bracket around indentation in glass. Align holes on
each end of bracket with holes at end of each arm on fixture.
11) Fit second bracket around indentation in glass. Align hole on
each end of bracket with holes at end of each arm on fixture
and holes in first bracket.
12) Slip end of one ball stud through holes in brackets and arm.
13) Thread ball knob onto end of ball stud protruding from hole
in bracket.
14) Repeats steps 12 and 13 for remaining ball stud and ball
knob.
15) Tighten both ball knobs to secure brackets in place.
1) COUPER LE COURANT.
IMPORTANT: TOUJOURS couper l’électricité avant de
commencer le travail.
a) Localiser le coffret à fusibles ou le disjoncteur du
domicile. Mettre l’interrupteur principal en position
d’Arrêt.
b) Dévisser le ou les fusibles (ou mettre le disjoncteur sur
Arrêt) qui contrôlent l’alimentation vers le luminaire ou la
pièce dans laquelle le travail est effectué.
c) Mettre l’interrupteur mural en position d’Arrêt. Si le luminaire
à remplacer est doté d’un interrupteur ou d’une chaîne
connectée à l‘interrupteur, placer ces éléments en
position d’Arrêt.
2) Serrer l’écrou hexagonal sur le tube fileté de sorte que 5
filets soient exposés en dessous de l’écrou hexagonal.
Depuis le dessous de la bride de montage, passer
l’extrémité longue du tube fileté dans le trou de la sangle de
montage jusqu’à ce que l’écrou hexagonal soit en contact
avec la bride de montage. *Resserrer l’écrou hexagonal
contre la bride de montage.
3) Serrer le deuxième écrou hexagonal sur l’autre extrémité du
tube fileté. Serrer l’écrou hexagonal contre la bride de montage.
4) Visser le collier de fixaiton à la boîte de jonction (vis non
fournies).
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 5/9/14 IS-45576-CB
INSTRUCTIONS
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
FIXTURE
LUMINAIRE
THREADED
PIPE
TUBO
FILETE
5) Connecter les fils (connecteurs non fournis). Se reporter au
tableau ci-dessous pour faire les connexions.
6) Plaquez l’applique contre le mur, en passant soigneusement
le tube fileté dans les trou.
7) Visser le bouchon fileté sur le tube fileté. Serrer le bouchon
fileté pour fixer le luminaire au mur.
8) Introduire l’ampoule recommandée.
9) Porter le verre au luminaire. Passez le trou dans le verre sur
l’ampoule. Monter le bord supérieur du verre à l’intérieur du
cache sur le luminaire.
10) Installer un support autour de l’indentation dans le verre.
Aligner les trous situés sur chaque extrémité du support
avec les trous situés à l’extrémité de chaque bras sur le
luminaire.
11) Installer un autre support autour de l’indentation dans le
verre. Aligner le trou situé sur chaque extrémité du support
avec les trous situés à l’extrémité de chaque bras sur le
luminaire et aux trous dans le premier support.
12) Glisser l’extrémité d’un goujon à bille par les trous situés
dans les supports et le bras.
13) Serrer le bouton à bille sur l’extrémité du goujon à bille
ressortant du trou du support.
14) Répéter les étapes 12 et 13 pour l’autre goujon à bille et
bouton à bille.
15) Serrer les deux goujons à bille pour fixer le support.
MOUNTING STRAP
COLLLIER DE
FIXATION
Connecter le fil noir ou
rouge de la boite
Connecter le fil blanc de la boîte
A Noir A Blanc
*Au cordon parallèle (rond et lisse)
*Au cordon parallele (à angles droits el strié)
Au bransparent, doré, marron, ou
noir sans fil distinctif
Au transparent, doré, marron, ou
noir avec un til distinctif
Fil isolé (sauf fil vert) avec
conducteur en cuivre
Fil isolé (sauf fil vert) avec
conducteur en argent
*Remarque: Avec emploi d’un fil paralléle
(SPT I et SPT II). Le fil neutre est á angles
droits ou strié et l’autre fil doit étre rond ou
lisse (Voir le schéma).
Fil Neutre
GLASS
VERRE
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
THREADED CAP
BOUCHON FILETE
CAP
CACHE
ARM
BRAS
BRACKET
SUPPORT
BALL STUD
GOUJON À
BILLE
BALL KNOB
BOUTON À
BILLE
HEXNUT
ECROU
HEXAGONAL
-
1
-
2
-
3
Kichler Lighting 45576OZ User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Kichler Lighting 43787PN User manual
-
Kichler Lighting 9886TZ User manual
-
Kichler Lighting 43436AUB User manual
-
Kichler Lighting 43436AUB User manual
-
Kichler Lighting Mount Vernon 9704 User manual
-
Kichler Lighting 43787PN User manual
-
Kichler Lighting 45637CHL18 User manual
-
Kichler Lighting 43603WZC User manual
-
Kichler Lighting 45568CHL18 User manual
-
Kichler Lighting 45568CHL18 User manual
