2seeU 2CU-X241-IP Operating instructions

Brand
2seeU
Model
2CU-X241-IP
Category
Security cameras
Type
Operating instructions
Thank you for your purchase of this product.
Before attempting to connect or operate this
product, please read these instructions completely.
The above drawing is for reference only.
MODEL:
OUTDOOR FIXED LENS
IP IR DOME CAMERA
2CU-X241-IP
2.0 Mega-Pixel
1.Installation and maintenance should be carried out by professional personnel as per
relative regulations. All electrical work must obey the latest electrical regulations,
fire regulations and relevant regulations. Check whether the accessories of the unit
are complete according to packing list and confirm whether the place and method of
installation is in accord with required, if not, please contact your supplier. Please
use this product in required environment.
2.This IP camera is designed for outdoor use.
3.After re-installation or repair, you need to measure the resistance between the
circuit and shell to check whether the insulation is good and ensure there is no
short-circuit between the circuit and shell.
4.Confirm there is enough place to contain the product and its structural components.
Confirm the ceiling, wall and bracket for installation can take the total weight of the
product and its structural components, and materials used to support the weight
can sustain four times the weight of the product.
5.Please check the product package well. You can send the IP camera to factory with
that package if there is any problem that needs to service.
INSTALL PREPARATION
PACKAGE CONTENTS
1. IP CAMERA.........................................................................................................1pcs.
2. CD.......................................................................................................................1pcs.
3. MOUNTING TEMPLATE STICKER.........................................................................1pcs.
4. SCREW...............................................................................................................3pcs.
5. WALL PLUG........................................................................................................3pcs.
FEATURES
1.Do not attempt to disassemble the camera.
2.Handle the camera with care.
3.The installation should be made by qualified service personnel or system installers.
4.Do not use strong or abrasive detergents when cleaning the camera body.
5.Clean the CMOS faceplate with care.
6.Never face the camera towards the sun.
7.Use the camera at temperatures within –10 °C to +50 °C, and humidity below 90 %
RH and the storage temperatures should be within –20 °C to +60 °C and humidity
below 20% to 80 % RH.
8.Please operate the camera within the specified power source ratings. Avoid
connections during a lightning storm. Otherwise, an electric shock may be caused.
PRECAUTIONS
!
DO NOT OPEN
RISK OF ELECTRIC SHOCK
CAUTION
DO NOT REMOVE COVER (OR BACK),NO
USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
TO REDUCE THE RISK OF ELECTRIC SHOCK,
CAUTION
!
The lightning flash with arrowhead
symbol, within an equilateral
triangle, is intended to alert the user
to the presence of uninsulated
dangerous voltage within the
product’s enclosure that may be
sufficient magnitude to constitute a
risk of electric shock to a person.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in literature accompanying the appliance.
CAUTION
1/2.5” Sony Exmor Progressive Scan Sensor
2.0 Megapixel Resolution (1936*1097)
Image Resolution: 1080P (1920x1080)/720 (1280x720)/D1 (704x576)/CIF (352x288)
Frame Rate 1080P@25fps; 960P@25fps; 720P@25fps
Dual Stream: Support Main Stream and Sub-stream
3.6mm (3.0 Mega) Fixed Focal Lens
H.264 and MJPG Compression
255 CH Free Admin Vision NVR& CMS Software
Support Admin Vision DDNS
Support ONVIF Ver.2.0 or 3rd.Party NVR/HVR on Request
True Day/Night with ICR on Sensor
Support Protocol TCP/IP, HTTP, DHCP, DNS, DDNS, PPPoE, SMTP, etc.
Power Supply: 12VDC & PoE Input
Support D-WDR/Motion Detection/BLC/Image Setup/ Day/Night/AGC/Smart IR,
etc.
Lowest Power Consumption
Lowest Heat on Board for Long Life of Camera
30 Meters Visual Distance with 36pcs LED (14mil Oblong IR LED Supreme Night
Visibility & Uniform IR with Proprietary Split Beam Lens on LED)
CAMERA CONNECTION
Network Interface
Connect the network interface using RJ 45 network cable. It shows working when the
network indicator is on.
12 V DC Power Supply
Connect the 12 Volt DC power using DC Jack. Please make sure the polarity is correct.
Incorrect polarity may cause malfunction and/or damage to the camera.
Wiring Precautions
Do not bend the coaxial cable into a curve whose radius is smaller than 10 times the
cable’s diameter.
Never staple the cable even if with circular staples. Otherwise impedance mismatching
will occur.
Print V1.0 Nov, 2K14
0230-00224
TECHNICAL SPECIFICATIONS INSTALLATION OF CAMERA
DIMENSIONS
Unit: mm
MOUNTING TEMPLATE STICKER
The mentioned technical drawing is for Reference only. Actual size of Mounting
Template Sticker is matched with Dome Base.
The above mentioned technical drawings are for reference only.
All dimensions are in millimeters and approximate.
1.Stick Mounting Template Sticker supplied for drilling the mounting hole on the
mounting surface. The unit is intended to be mounted with three #10 screws through
the three outer holes at the base of dome camera.
2.Install the appropriate anchors or threaded fasteners.
Installation Template
Lens Type
Model Name
Min. illumination
S/N Ratio
Image Resolution
Exposure Mode
System Compatibility
Gain Control (AGC)
Slow Shutter
More than 50dB (AGC OFF)
Automatic/Manual(1/50, 1/120, 1/250, 1/500, 1/1000,
1/2000, 1/4000, 1/10000)
Support ONVIF2.0
Open/Close (Limit: 100)
Total Pixels
Image Sensor
Color: 0.1Lux @ F1.2, B/W: [email protected]
Slow Shutter
None/Low/Medium/High
Low/Medium/High
Day/Night Mode
Automatic/Color/Black and White
Profile
Automatic/Indoor/Outdoor
White Balance
Auto Multi-matrix White Balance (AWB)
AE Sensitivity
1-10, adjustable
Dnc Threshold
10-50, adjustable
Compression Type
H.264/MJPEG
Back Light Compensation
(BLC)
Close/Open
Anti-flicker control
Selectable 50Hz / 60Hz
On-camera real-time
Motion Detection
Support
Network Service
Support TCP/IP, HTTP, DHCP, DDNS, PPPoE, SMTP NTP, etc.
Dual Stream
Mobile Support Iphone, IPad, Android, Windows, Blackberry & Symbian
Power over Ethernet (PoE)
Support
Power Supply
Dimensions (mm)
Weight (g)
12V DC/PoE
3.6mm (3.0 Mega) Fixed Focal Lens
No heater: -10°C (14°F) to +50°C (122°F)
0% to 90% (non-condensing)
Operating Temperature
/ Humidity
Support Main Stream and Sub-stream
Ingress Protection
Waterproof Housing (IP66)
85.5 (Base Dia.) X 85.0 (H)
Approx. 286
1/2.5” Sony Exmor Progressive Scan Sensor
2.0 Megapixel Resolution (1936x1097)
1080P (1920x1080)/720 (1280x720)/D1 (704x576)/CIF (352x288)
Max. FPS
1080P@25fps; 960P@25fps; 720P@25fps
2CU-X241-IP
85.0
Ø85.5
Mounting Template
Sticker
Ceiling
  • Page 1 1
  • Page 2 2

2seeU 2CU-X241-IP Operating instructions

Brand
2seeU
Model
2CU-X241-IP
Category
Security cameras
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents