2. Computers & electronics
  3. Networking
  4. Network switches
  5. Genexis
  6. E600
E600

Genexis E600 Installation guide

  • Hello! I have analyzed the provided installation guide for the genexis Pure Series E600 router. This document covers mounting options, initial setup, Wi-Fi configurations, and accessing the web interface. I can help with questions regarding router's operation, the LED indicators, and troubleshooting common issues.
  • How do I switch the WiFi on?
    How do I switch the WiFi off?
    What should I do if the Status LED is solid red?
    How do I return the Pure E600 to factory default settings?
E
Pure Series
Installation Guide
Wi-Fi EasyMeshTM suppoted
Pure E setup as an Ethernet based router
Geting stated
Check if the following items are in
the gitbox:
• Genexis Pure E
• Power adapter
• RJ nework cable
• Labels (self-adhesive)
• Rubber feet (self-adhesive)
• Plugs & screws
Placement
Pure suppots wo placement options;
standing (desktop) and mounted to a wall. It is
recommended to place the device ‘away’
from obstacles and objects.
Standing
. Place the device on a lat suface
using the stand.
. The rubber feet need to be atached to the
stand accessoy for stable placement.
Wall mount
. Download and print the drilling
guide from htps:genexis.euproduct
puredownloads
. Use the drilling guide to drill the holes,
inset plugs and put screws into place.
. Remove the stand from the device by
sliding it towards the front.
. Store the stand in a safe place.
. Use the wall mount points on the back
of the Pure E to mount the device
to the screws.
Warning: Do not cover the device with
anything, this will intefere with the
ventilation of the Pure E.
Operation Temperature °C ~ °C
Various translations of this document (if available) and additional product information can be
foundon htps:genexis.euproductpuredownloads
Installation guide
You're just a few steps away to install your device
via the Genexis EasyWiFi app
Installation with use of app
Scan QR-code
Download app and
follow the steps
Connecting to the wireless nework
You can connect your personal device to the
Pure E via manual pairing. If automated
pairing (WPS) is prefered, please check for
your speciic device how this can be initiated.
Before pairing , make sure the WiFi LED is on
(solid green). If not, switch the WiFi ON as
described in this installation guide.
Manual pairing
The WiFi nework name and WiFi key
are printed on the labels of the Pure E.
. Peform a search of available wireless
neworks on your personal device or scan
the QR-code on the label of the Pure E.
. Select the WiFi nework name printed on
the labels of the Pure E.
. Enter the WiFi key printed on the labels of
the Pure E.
Using the web inteface
You can access the Pure E web inteface
via a wired connection or wireless connection.
• Wired connection: Connect an RJ
nework cable beween your personal
device and the Pure E LAN pot
(yellow connector).
• Wireless connection: Connect your personal
device to the wireless nework as described
in this installation guide.
. Use a web browser on your personal
device and navigate to the GUI URL
as printed on the labels of the Pure E
. Login using the credentials as printed on
the labels of the Pure E.
Power saving options
Power saving options are available via the
web inteface.
Seting up the Pure
. Connect an RJ nework cable beween
your broadband outlet and the Pure E
WAN pot (red connector).
. If required, connect your telephone to the
FXS phone pot.
. Connect the supplied power adapter
to the Pure and plug the adapter into a
power socket.
. Flip the ONOFF switch at the back of the
device to turn it on.
. If the device is connected properly, the
Status, Uplink and Internet LEDs will have
a solid green color.
Switching the WiFi ONOFF
The WiFi function of the Pure E can be
switched ON or OFF by means of
the Mode buton.
• Switch OFF: On the Pure E, press and
hold the Mode buton until the WiFi LED
turns o.
• Switch ON: On the Pure E, press and
hold the Mode buton until the WiFi LED
turns on.
Reset buton (recessed)
Reboot – shot press (up to  seconds)
Factoy reset – long press (more than
 seconds)
ONOFF switch
Switch ON – lip the switch to ON
Switch OFF – lip the switch to OFF
WAN pot
Reset buton
LAN pots
USB . pot
FXS pots
ONOFF
switch
Power pot
Status
Green – system is operational ready
Yellow – system boot initialization
Yellow (blinking) - system is not ready yet
Blue – WPS pairing successfull
Blue (blinking) – WPS pairing in progress
Red – system  booting failure
O – power o
Uplink
Green – link ok
O – no link
Internet (IP connectiviy)
Green – connected (DNS available)
Green (blinking) – connection failed (no DNS available)
O – no IP connectiviy
Phone
Green – telephony sevice registered and operational
Green (blinking) – telephony sevice in progress to register
O – telephony sevice is disabled
Wireless (WiFi)
Green – wireless nework . GHz andor  GHz active
O – wireless neworks inactive
Mode buton
Pairing (WPS) – press and release once
WiFi ON – press and hold until WiFi LED turns solid green
WiFi OFF – press and hold until WiFi LED turns o
LED & buton oveview Pot oveview
Return the Pure E to factoy default
setings
With the reset buton you can reset the Pure
E to its factoy default setings. You can
press this buton with a small pin or paperclip.
. Press and hold the reset buton until all LED’s
stat fast blinking green.
. Wait until the Status LED turns solid
green again.
Your Pure E is returned to its default
setings as printed on the labels of
the Pure E.
Troubleshooting
Is the Status LED solid red?
Contact your sevice provider.
Is the Status LED not solid blue ater
Automated pairing (WPS)?
Automated pairing beween the Pure E
and your personal device failed. Please follow
the instructions again to connect your
personal device to the wireless nework.
Is the Status LED blinking yellow and the
Uplink LED is blinking green?
The Pure E is being upgraded with new
soware. Please wait until the status LED
turns solid green again.
Is the Uplink LED o?
Pure E does not have a connection with
the broadband nework. Please verify your
wired connection with the broadband outlet
or contact your sevice provider.
Is the Internet LED o?
Pure E does not have an internet
connection. Please contact your
sevice provider.
Is the WiFi LED o?
The WiFi of the Pure E is turned OFF.
Please turn the WiFi ON as described in this
installation guide.
EU Declaration of Conformiy
Company Name
Genexis Netherlands B.V.
Company Address
Lodewijkstraat a
 AC Eindhoven
The Netherlands
Name and title of authorized person
Maaten Egmond, CTO
Signature of authorized person
Place of issue Date of issue
Eindhoven --
The Netherlands
Hereby, Genexis Netherlands B.V. declares that the radio equipment ype Pure E is in
compliance with Directive EU, Directive EC, Directive EU and
Delegated Directive .
The full text of the EU declaration of conformiy is available at the following internet address:
htps:genexis.euproductpureredpure-e
Frequency bands and maximum radio frequency power transmited
The Pure E operates in the frequency bands of , Ghz and Ghz.
The maximum radio frequency power transmited in these bands is:
•  dBm( mW) (EIRP)for the  MHz – . MHz band
•  dBm ( mW) (EIRP)for the  MHz –  MHz band *
•  dBm ( mW) (EIRP) for the  MHz –  MHz band
* In EU,  –  MHz is restricted to indoor.
Revision . - September  - Copyright ©  Genexis Netherlands B.V. All rights reseved.
Genexis assumes no responsibiliy for any inaccuracies in this document. Genexis reseves the right to
change, modify, transfer, or othewise revise this publication without notice.
/