Genexis Pulse EX600 Installation guide

Brand: Genexis

Model: Pulse EX600

Type: Installation guide

Genexis Pulse EX600 is a versatile networking device that can be used as a router, wireless extender, or wired extender. It features dual-band Wi-Fi (2.4GHz and 5GHz) for faster speeds and better coverage, and it's easy to set up using the Genexis EasyWiFi app. With its compact design and multiple placement options, the Pulse EX600 is a great choice for expanding your home network and eliminating Wi-Fi dead zones.

EX

Pulse Series

Installation Guide

Wi-Fi EasyMeshTM suppoted

Box contents

• Genexis Pulse EX

• Power adapter

• Nework cable

• Labels (self-adhesive)

• Plugs & screws

Placement

Pulse EX suppots wo placement

options; desktop and mounted

to a wall. It is recommended to place

the device ‘away’ from objects.

Desktop

. Place the device horizontally on a

lat suface.

Wall mount

. Download and print the drilling

guide from htps:genexis.eu

productpulsedownloads

. Use the drilling guide to drill the

holes, inset plugs and put

screws into place.

Use the wall mount points on the back of the

Pulse EX to mount the device to the screws.

Various translations of this document (if available) and additional product

information can be foundon htps:genexis.euproductpulsedownloads

Installation guide

Pulse EX can be setup as a router or wirelesswired extender.

You're just a few steps away to install your device

via the Genexis EasyWiFi app

Installation with use of app

Scan QR-code

Download app and

follow the steps





Extender placement

For optimal peformance of the

Pulse EX as extender; place the

Pulse EX halfway in beween

your router and the problem area (as

shown below). Make sure placement

is within WiFi range of your router. If

the extender is placed too far away, it

cannot connect to the router.

Pulse EX

Router

Problem area, improved

by Pulse EX

Area that is good for

placing Pulse EX

Area covered by your

router

Installation of your Pulse device(s)

This installation guide is for installing

the Pulse EX as a router, as

explained on the right. In addition, an

extra Pulse EX can be installed as

a wireless or wired extender behind

the Pulse EX router.

If you already have a dierent router

(not a Pulse EX) and want to

install it as an extender, then look for

installation options: htps:genexis.

eupulse-installation-guide

Router

If you do not have a router installed,

stat installing your Pulse EX here:

. Place your Pulse EX near your

broadband outlet.

. Connect a nework cable beween

your broadband outlet and the

Pulse EX WAN pot (red pot).

. Plug the power adapter into an

electrical socket and connect it to

the power pot at the back of

the Pulse EX.

. Flip the ONOFF switch at the

back of the device to turn it on.

. Wait until the Status LED stops

blinking and turns solid green.

Your Pulse EX is now setup as a

router. Your nework is now ready to

be extended with a wireless or

wired extender, as explained on the

next pages.

Switching the WiFi ONOFF

The WiFi function of the Pulse EX

can be switched ON or OFF by

means of the Mode buton.

• Switch OFF: On the Pulse EX,

press and hold the Mode buton until

the Status LED turns solid yellow.

• Switch ON: On the Pulse EX,

press and hold the Mode buton until

the Status LED stats blinking green

or turns solid green.

Connecting to the wireless nework

You can connect your personal

device (e.g., mobile phone) to the

Pulse EX via manual pairing. If

automated pairing is prefered, please

check for your speciic device how

this can be initiated. Before pairing,

make sure the Status LED is solid

green. If not, switch the WiFi ON as

described in this installation guide.

Manual pairing

The WiFi nework name and WiFi key

are printed on the labels of the

Pulse EX router.

. Peform a search of available

wireless neworks on your personal

device or scan the QR-code on the

label on the botom of the

Pulse EX.

. Select the WiFi nework name

printed on the label on the botom

of the Pulse EX.

. Enter the WiFi key printed on the

label of the Pulse EX.

Follow the instructions of the router

in case the Pulse EX is in

extender mode.

Wireless extender

. Place the additional Pulse EX

as described on the let.

. Plug the power adapter into an

electrical socket and connect it to

the power pot at the back of

the Pulse EX.

. Flip the ONOFF switch at the

back of the device to turn it on.

. Wait until the Status LED

surrounding the Mode buton

stats blinking green.

. On the Pulse EX, press and

release the Mode buton once. The

status LED will stat blinking blue.

. Press the same Mode buton on

the Pulse EX router within

wo minutes.

. Automated pairing is now stated.

. The Status LED turns solid blue

indicating that pairing of the Pulse

EX extender with the router

is successful (the Pulse EX will

automatically reboot ater the

automated pairing; this may take

up to several minutes).

. Wait until the Status LED stops

blinking and turns solid green.

Your Pulse EX is now setup as a

wireless extender.

Wired extender

. Connect a nework cable beween

the LAN pot (yellow connector)

of the Pulse EX router and the

WAN pot (red connector) of the

Pulse EX extender.

. Plug the power adapter into an

electrical socket and connect it to

the power pot at the back of the

Pulse EX extender.

. Flip the ONOFF switch at the

back of the device to turn it on.

. Wait until the Status LED stops

blinking and turns solid green

(the Pulse EX extender will

automatically reboot during the

setup; this may take up to

several minutes).

Your Pulse EX is now setup as a

wired extender.

LED & buton oveview

Status

Green – system is operational ready

Green (blinking) – connectiviy lost

Yellow – system statup or WiFi OFF

Yellow (blinking) – system is not ready

Blue – automated pairing (WPS) successful

Blue (blinking) – automated pairing (WPS) in progress

Red – system  booting failure

O – power o

Mode buton

Pairing (WPS) – press and release once

WiFi ON – press and hold until Status LED turns green

(blinking or solid)

WiFi OFF – press and hold until Status LED turns solid

yellow

Changing your nework setings

You can access the Pulse EX

web inteface (GUI) to change your

nework setings. The Pulse EX

must be in router mode to access

the GUI.

. Use a web browser on your

personal device and navigate to

the GUI URL as printed on the label

on the botom of the Pulse EX

. Login using the credentials as

printed on the labels on the

botom of the Pulse EX.

Power saving options

Power saving options are available via

the web inteface.

Pot oveview

Power pot

ONOFF

switch

LAN pots Reset

buton

WAN pot

USB .

pot

ONOFF switch

Switch ON – lip the switch to ON

Switch OFF – lip the switch to OFF

Reset buton (recessed)

Reboot – press and release once

Factoy reset – press and hold until the

Status LED stats fast blinking green

Troubleshooting

Is the Status LED solid red?

Contact your sevice provider.

Is the Status LED solid yellow?

The WiFi of the Pulse EX is turned

OFF. Please turn the WiFi ON as

described in this installation guide.

Is the Status LED not solid blue ater

automated pairing (WPS)?

Automated pairing (WPS) beween

the Pulse EX and Genexis router

or personal device failed. Please follow

the instructions again to setup the

Pulse EX as a wireless extender

or connecting your personal device

to the wireless nework. It might be

helpful to move the Pulse EX

closer to your Genexis router.

Is the Status LED blinking green for

 minutes?

• Router: Pulse EX does not have

a connection with the broadband

nework. Please verify your wired

connection with the broadband

outlet or contact your

sevice provider.

• Wirelesswired extender:

Connection beween the Genexis

router and the Pulse EX is

not stable. Please check the cable

connection with the Genexis router

or move the Pulse EX closer to

the Genexis router.

Is the Status LED blinking yellow?

The Pulse EX is being upgraded

with new soware. Please wait until

the Status LED turns solid green

again.

Return the Pulse EX to factoy

default setings

With the reset buton you can reset

the Pulse EX to its factoy default

setings. You can press this buton

with a small pin or paperclip.

. Press and hold the reset buton

until the Status LED stats fast

blinking green.

. Wait until the Status LED turns

solid green again.

Your Pulse EX is now setup as

a router again with the setings as

printed on the label of

the Pulse EX.

Company Name

Genexis Netherlands B.V.

Company Address

Lodewijkstraat a

 AC Eindhoven

The Netherlands

Name and title of authorized person

Maaten Egmond, CTO

Signature of authorized person

Place of issue Date of issue

Eindhoven --

The Netherlands

Hereby, Genexis Netherlands B.V. declares that the product Pulse EX is in

compliance with Directives EU, EC, EU and

Delegated directive .

The full text of the EU declaration of conformiy is available at the following

internet address: htps:genexis.euproductpulseredpulse-ex

EU Declaration of Conformiy

Frequency bands and maximum radio frequency power transmited

The Pulse EX operates in the frequency bands of , Ghz and Ghz.

The maximum radio frequency power transmited in these bands is:

•  dBm( mW) (EIRP)for the  MHz – . MHz band

•  dBm ( mW) (EIRP)for the  MHz –  MHz band *

•  dBm ( mW) (EIRP) for the  MHz –  MHz band

* In EU,  –  MHz is restricted to indoor.

Genexis assumes no responsibiliy for any inaccuracies in this document. Genexis reseves

the right to change, modify, transfer, or othewise revise this publication without notice.

Genexis Pulse EX600 Installation guide

Genexis Pulse EX600 Installation guide

Genexis Pulse EX600 Installation guide

Related papers

Other documents