Jelanry BT-A2 Operating instructions

Brand: Jelanry

Model: BT-A2

Category: Mobile headsets

Type: Operating instructions

Jelanry BT-A2: Wireless Freedom at Your Fingertips!

Experience the convenience of true wireless earbuds with Jelanry BT-A2. These earbuds boast Bluetooth 5.0 for a stable connection, ensuring smooth music streaming and clear calls without interruptions. With a battery life of up to 4 hours on a single charge and a charging case that provides an additional 12 hours of playtime, you can enjoy your favorite tunes all day long.

Effortlessly control your music and calls with the intuitive touch controls located on each earbud. Play, pause, skip tracks, adjust volume, and even activate your phone's voice assistant with just a few taps.

Jelanry BT-A2: Wireless Freedom at Your Fingertips!

Pay Attention:

Packing List:

The earphones have built-in high-quality

lithium batteries. In order to get a better

battery life, be sure to charge the earphones

for 60 minutes when using it for the ﬁrst time.

* Bluetooth Headset (2pcs)

* Headset Charging Case

* USB to USB C Charging Cable

(If you encounter unsolvable product problems,

be sure to contact the dealer's customer service

staﬀ to obtain an eﬀective solution)

Speciﬁcations:

* User's Guide

* Zipper Storage Case

* Name: BT-A2/BT-A3

* Bluetooth Version: 5.0

* Power Input: DC 5V

* Battery Capacity: 3.7V / 50mA

* Working Time: 3-4 hours

* Support Agreement: HSP / HP / A2DP / ARCP

* Impedance: 32Ω

Product Instructions:

1. Power On / Oﬀ:

1.1 Automatic Startup:

TWS HEADSET

INSTRUCTIONS

BT-A2/BT-A3

If the headset is not used for a long time,

the headset enters the sleep state. When

you need to use it, put the headset into the

charging compartment, then take it out,

and it will automatically turn on.

1.2 Manual Startup:

Press and hold the headset touch area for 4

seconds, the blue light ﬂashes and the boot

is complete

1.3 Automatic Shutdown:

When not in use, put the headset in the

charging case to turn oﬀ automatically.

(Note: When the power of the charging

cabin is insuﬃcient, the headset will not

automatically switch on and oﬀ)

2. Pairing Mode

1.4 Manual Shutdown:

Press and hold the headset touch area for 5

seconds, the red light ﬂashes continuously

to complete the shutdown.

2.1 The ﬁrst time you use the headset, the

left and right headsets need to be paired.

This process takes about 10 to 30 seconds

to complete according to the environment.

Methods as below:

Open the charging compartment cover, the

headset is taken out to enter the automatic

pairing mode, and the left and right ears

alternately ﬂash red and blue. After

successful connection, any one of the

headset indicators will turn oﬀ, indicating

3. Paring with Mobile Phone

that the connection is successful, and at the

same time the headset will have a voice

prompt to indicate the connection status.

3.1 Android / IOS:

3.1.1 Turn on the Bluetooth of the mobile

phone, ﬁnd the device name of the BT-A2/

BT-A3 in the search list, click connect, and it

can be used after the connection is

successful (if the pairing with interference

fails, repeat above operation).

3.1.2 If the connection is successful, but there

is no sound from the headset, please ignore

this Bluetooth device in the phone search list,

and then reconnect.

3.1.3 When the mobile phone and the

Bluetooth headset have been paired

successfully, when the mobile phone

Bluetooth is turned on, the headset will

automatically connect to the mobile phone

when it is turned on.

4. Switch Single or Double Ear Mode

4.1 Binaural Mode:

The headset defaults to binaural mode, and

you can use both ears after successful

connection.

4.2 One Ear Mode:

After the connection is successful, when

playing music or answering the phone, put

any earphones back into the charging

compartment. The earphones that are still

wearing will continue to work and will not be

aﬀected. Put the earphones back into the

charging compartment and take out,

automatically restore the binaural mode .

(Note: If the earphone automatically becomes

the mono-ear mode, only one earphone

sounds, you can put both earbuds into the

charging compartment at the same time to

reset the earphones.)

5. Charging Instructions

5.1 Charging Headset:

Put the earphone back into the charging

compartment, the earphone will charge

automatically. The red light of the earphone

is always on when charging, the blue light

will be on when it is full, and it will go out

after 2 minutes. Full charge is about: 1 hour.

After a full charge, it automatically enters

sleep (please ensure that the charging

compartment has suﬃcient power).

5.2 Case Charging:

When the charging compartment is less than

20% of power, the charging case power

indicator ﬂashes. Please charge in time to

ensure the normal use of the headset. (For

your safety, be sure to use a USB charger

that complies with safety regulations.) It is

recommended that you use the original USB

charger of the mobile phone. The full time

is about 40 minutes. You can charge the

headset about 4 times when the charging

compartment is fully charged.

1. The headset should be stored in a dry and

ventilated environment, avoid contact with oil,

water vapor, steam, moisture and dust, so as

not to aﬀect the performance and life of the

product. It is strictly forbidden to place the

headset in a high temperature environment

exceeding 50 C, otherwise the battery may crack.

2. Avoid using harsh organic solvents or

objects containing these ingredients to clean

the headphones. The charging contacts of the

headset need to be regularly moistened with a

small amount of alcohol / rust-proof oil on a

cotton swab and wiped clean to keep the

headset charging function normal.

3. The headset should be used in accordance

with the speciﬁcations of the manual. Pay

attention to the impact of the use

environment on the headset. To ensure a

smooth connection, it is recommended that

the distance between the mobile phone and

the headset be within 10 meters of the

obstacle-free range.

4. If there are other problems such as the

headset is not connected or the communica-

tion is not smooth, please do not disassemble

the headset body and its accessories without

permission, otherwise the warranty will not

be granted.

5. To charge the headset, please choose a

household or car charger that complies with

safety regulations.

6. To ensure that you use the headset

normally, please ensure that the charging

case and headset have suﬃcient power.

6. Touch Control Description:

Touch the O area of the earbuds with your

ﬁnger to realize the operation function. If you

do not understand the touch function,

misoperation will occur, please read the

deﬁnition of touch function in detail. The

speciﬁc function description refers to the

following table:

Note: In order to ensure the safe use of the headset, please read in detail.

Voice Assistant

Play / Pause Music

Next Track

Previous Piece

Volume +

Volume -

Chinese / English

Switch

Answer/End a Call

Reject call

Press for 3 seconds on any left / right ear

ouch left / right ear once during playback

Click Right ear 2 times

Click Left ear 2 times

Click Right ear 3 times

Click Left ear 3 times

Touch 2 times on any left / right ear ( when

headset is not connected with any device)

Touch left / right ear once

Long press on any left / right ear for 2 seconds

Jelanry Jelanry Jelanry Jelanry Jelanry Jelanry

Jelanry BT-A2 Operating instructions

Brand: Jelanry

Model: BT-A2

Category: Mobile headsets

Type: Operating instructions

Jelanry BT-A2: Wireless Freedom at Your Fingertips!

Download PDF

report

Jelanry BT-A2 Operating instructions

Jelanry BT-A2 Operating instructions

Other documents