i3 International IP01P User manual

Brand: i3 International

Model: IP01P

Type: User manual

i3 International IP01P is a PoE over Coax Extender that allows you to power IP devices and transmit IP signals up to 328 feet (100 meters) using existing coaxial cable infrastructure. It's compatible with i3's line of IP cameras and PoE switches, providing a reliable and cost-effective solution for extending the reach of your network.

Thank you for purchasing i3 International’s IP01P PoE extender (sold in pairs). Use IP01P as a point-to-point PoE (Power over

Ethernet) extender to power IP devices and to carry IP signal for distances of up to 328 feet (100 meters) using existing coaxial cable

infrastructure. Use with i3’s line of IP cameras and PoE switches.

INSTALLATION

PoE over Coax Extender, 300 ft IP01P

User Manual

i3-TRNG-ACCESSORIES-IP01P.indd

Rev. 220913

FEATURES

• Signal extension up to 328 ft (100 m) over RG59/RG6U

coaxial cable.

• Power from a PoE switch or injector.

• Bandwidth up to 10Mbps.

• Use with i3’s PoE cameras and with i3 PoE switches.

*Note: M79, Ax85, Ax19 are not supported.

PACKAGE CONTENTS

1. IP01P x2 (one pair)

2. Crossover cable x2 (8 in / 20 cm)

3. Plastic Anchor x4

4. Round Head Screw (Tapping Type) x4

PoE Cameras &

other IP devices

IP01P

i3 INTERNATIONAL INC. 1.866.840.0004

www.i3international.com

REGULATORY NOTICES (FCC CLASS A)

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the

limits of a Class A digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area

is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

IP01P

328 ft 100 m10 ft 3 m 10 ft 3 m

PoE Switch

CONNECTORS

1. BNC Connector. Connect to the second IP01P device

using the RG59 cable, 328 ft (100 m) or less.

The link speed is up to 10 Mbps.

2. PoE Mode Selector Switch. Pre-set to MID SPAN

setting (recommended). See Tables 2, 3.

IMPORTANT: Unplug power before switching between

MID SPAN and END SPAN modes to avoid damage.

3. Power LED Indication. Indicates device power status.

See Table 1.

4. RJ45 Connector. Connect one IP01P to the PoE IP

device and the other to PoE Switch. Do not exceed 10 ft

(3 m) cable run between IP01P and PoE equipment.

Figure 2. IP01P front and back panels, parts description.

243

RJ45 straight connection RJ45 straight connection

RG59 / RG6U coaxial

Figure 1. IP01P connection diagram. WARNING

Unplug power before switching between MID SPAN and END

SPAN modes to avoid damage to the device.

Figure 3. IP01P front and back panels

i3-TRNG-ACCESSORIES-IP01P.indd

SPECIFICATION

IP01P

Compliance IEEE 802.3af Power over Ethernet

IEEE 802.3at Power over Ethernet Plus

Bandwidth 10 Mbps

Max.

Transmission

Distance 10Mbps @ 328 ft (100 m)

Ports & Interfaces

Input 1 x RJ45

Output 1 x 75Ω BNC

Power

Consumption 1.25W (Max)

Environmental speciﬁcations

Operation 32-131 °F (0-55 °C)

Storage -4-185 °F (-20-85 °C)

Humidity ≤ 95%

Physical Characteristics

Dimensions 2⅝” x 3 7/16” x 1 1/16” (67 x 87 x 27mm)

Weight 0.33 lbs (150 g)

i3 INTERNATIONAL INC. 1.866.840.0004

www.i3international.com

IP01P. PoE over Coax Extender, 300 ft

QUICK START GUIDE

Mode RJ45 pin#

for power

transmission

END SPAN 1/2 and 3/6

MID SPAN (Default),

Recommended 4/5 and 7/8

Table 2. PoE Mode Selector

ACT Download &

Documentation

Scan this QR code or visit ftp.i3international.

com for Annexxus Configuration Tool (ACT)

installation and additional documentation.

Contact our Technical Support team at:

1.877.877.7241 or support@i3international.

com if you have any questions or concerns

regarding camera installation or if you require

software services or support.

Green ON Green OFF

Power ON Power OFF

Table 1. Power Status LED

PIN Color MID SPAN

Default, recommended END SPAN

1 White Orange TX+

TX+ / PoE +

2 Orange TX-

TX- / PoE +

3 White Green RX+

RX+ / PoE -

4 Blue PoE+

5 White Blue PoE+

6 Green RX-

RX- / PoE -

7 White Brown PoE-

8 Brown PoE-

Table 3. END SPAN / MID SPAN Pin Layout

POE MODE

PIN LAYOUTPOWER STATUS

RJ45 CABLE CONNECTION

• Ethernet cable length must not exceed 10 ft (3 m)

• Straight connection is recommended when using MID SPAN.

• If the RJ45 Power Status LED is OFF, or when using END

SPAN, use one of the other cable connection combinations

until the LED turns ON.

• RJ45 cable connection combinations. Two crossover patch

cables are provided.

- Straight + Straight (recommended, use with MID SPAN)

- Straight + Crossover (use with END SPAN)

- Crossover + Straight (some non-i3 PoE cameras)

- Crossover + Crossover (some non-i3 PoE cameras)

PoE Cameras &

other IP devices

IP01P

328 ft 100 m

10 ft 3 m 10 ft 3 m

PoE Switch

RJ45 straight connection RJ45 straight connection

RG59 / RG6U coaxial

Figure 4. IP01P RJ45 cable connection

i3 International IP01P User manual

i3 International IP01P User manual

i3 International IP01P User manual

Related papers

Other documents