Tempo 2 One Shot or Test Timer Installation guide

Tempo2

One-Shot/Test Timer

Rev. 022807 More than just power.TM

Installing Company: _______________ Service Rep. Name: __________________________________

Address: _____________________________________________ Phone #: __________________

Installation Guide

- 2 - Tempo2 Installation Guide

Overview:

Altronix Tempo2 Digital Test / Trigger Mode Timer is suitable for many applications that require a timed operation.

e.g. delayed egress with a programmable 1-60 second door release after delay expires, door prop alarm, door

annunciator, alarm swinger eliminator, etc. Digital display facilitates ease of programming and indicates time

remaining before relay activation. Daily/Weekly test mode can be used to trigger digital communicators or radio

transmitters and provide Central Stations with an alarm test signal.

Specifications:

• Input 12 or 24 Volts AC or DC operation.

• Triggers via dry contact closure.

• Output dry Form “C” contacts are 2A @ 120VAC/28VDC.

• LCD display facilitates programming and indicates countdown status.

• Current draw: stand-by 15mA, relay energized 30mA.

• Dual function: test timer/one shot.

• EE Prom memory protects against loss of programming due to power failure.

• Board dimensions (L x W x H approximate): 3” x 2.5” x 0.75” (76.2mm x 63.5mm x 19.1mm).

One-Shot Features (trigger activated):

• Programmable relay activation at the start or end of the timing cycle.

a. Delayed Pulse Mode:

- 1 to 60 sec. programmable pulse at the end of timing cycle.

b. Delay Mode:

- Relay can be programmed to energize or de-energize during timing cycle

(Digitally adjust from 1 sec. - 24 hours).

Dry

relay

output Advance

CNC NO

POWER

12-24

VDC/VAC

Dry

Trigger

IN1

Confirm

Tempo2 Installation Guide - 3 -

Test Timer Options:

• Programmable weekly or daily test. (Test can be programmed for

a specific day and time).

1. Depress and Hold Confirm SU 00:00 will appear in display.

for 2 seconds until TestMode

2. Depress Advance SU 00:00 will appear in display.

SetClock

3. Depress and Hold Confirm SU 00:00 will appear in display.

for two (2) seconds Set day

Enter the current day of the week by depressing Advance

to make the selection.

4. Depress Confirm SU 00:00 will appear in display.

Set hour

Enter the current hour of day by depressing Advance to make the selection.

5. Depress Confirm SU 00:00 will appear in display.

Set min

Enter the current minute of day by depressing Advance to make the selection.

6. Depress Confirm SU 00:00 will appear in display.

TestMode

7. Depress Advance twice SU 00:00 will appear in display.

TestTime

8. Depress and Hold Confirm SU 00:00 will appear in display.

for two (2) seconds Test day

Enter the desired day of the week by depressing Advance to make the selection

(MO-SU or ** for every day test).

9. Depress Confirm SU 00:00 will appear in display.

TestHour

Enter the desired hour of day by depressing Advance to make the selection.

10. Depress Confirm SU 00:00 will appear in display.

Test min

Enter the desired min of day by depressing Advance to make the selection.

11. Depress Confirm pulse= 1 will appear in display.

Duration

Depress Advance to select duration of relay operation (1-60 seconds), then depress Confirm to accept.

- 4 - Tempo2 Installation Guide

Trigger Mode Programming:

1. Depress Advance 00:00:00 will appear in display.

Change ?

2. Depress and Hold Confirm 00:00:00 will appear in display.

for 2 seconds until SetDelay

Enter the desired amount of hours by depressing Advance to make the selection.

3. Depress Confirm 00:00:00 will appear in display.

SetDelay

Enter the desired amount of minutes by depressing Advance to make the selection.

4. Depress Confirm 00:00:00 will appear in display.

SetDelay

Enter the desired amount of seconds by depressing Advance to make the selection.

5. Depress Confirm pulse = 1 will appear in display.

Set PLS

Depress Advance to select pulse duration (1-60 seconds). If pulse is not needed skip to step 6.

6. Depress Confirm TRIG_OFF will appear in display.

TRG_EDGE

Enter the desired trigger option (OFF, ON, CNG) by depressing Advance to make the selection.

Removal of trigger will start time cycle.

OFF option starts timing cycle when trigger is removed.

ON option starts timing cycle when trigger is applied.

CNG option starts timing cycle when trigger is removed or applied.

7. Depress Confirm RLY = ON will appear in display.

Event

Enter the desired relay option (OFF, ON, PLS) by depressing Advance to make the selection.

OFF option - relay turns off at the end of timing cycle.

ON option - relay energizes at the end of timing cycle.

Pulse option - relay energizes momentarily (1 to 60 sec).

Depress Confirm to accept .

Tempo2 Installation Guide - 5 -

Tempo2 Typical Applications:

Fig. 1 - Timed Door Annunciator:

Dry

relay

output Advance

CNC NO

POWER

12-24

VDC/VAC

Dry

Trigger

IN1

Confirm

Normally open

door contacts

+ ---

CHIME

--

+

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

Fig. 2 - Guard Tour Supervisory Timer:

Dry

relay

output Advance

CNC NO

POWER

12-24

VDC/VAC

Dry

Trigger

IN1

Confirm

DIALER OR

TRANSMITTER

+ ---

Normally open

switch contacts

For this application select

Trigger “CHG” and Relay “PULSE”.

For this application select

Trigger “CHG” and Relay “OFF”.

- 6 - Tempo2 Installation Guide

Tempo2 Typical Applications (cont’d):

Fig. 3 - Swinger Eliminator:

Dry

relay

output Advance

CNC NO

POWER

12-24

VDC/VAC

Dry

Trigger

IN1

Confirm

+ ---

Protective circuit

To closed circuit

zone on

control panel

For this application select

Trigger “OFF”, Relay “ON”.

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

Fig. 4 - Delay Timer:

Use for Door Ajar Alarm, Delayed Activation of Digital Dialer, Defrost Cycle Timer, etc...

Dry

relay

output Advance

CNC NO

POWER

12-24

VDC/VAC

Dry

Trigger

IN1

Confirm

Normally open or

normally closed

switch contacts

SOUNDER

--

+

+ ---

For Normally Closed Trigger Contact select

Trigger “OFF”, Relay “ON”.

For Normally Open Trigger Contact select

Trigger “ON”, Relay “ON”.

Tempo2 Installation Guide - 7 -

Tempo2 Typical Applications (cont’d):

Fig. 5 - Timed Door Lock:

Dry

relay

output Advance

CNC NO

POWER

12-24

VDC/VAC

Dry

Trigger

IN1

Confirm

--

+

Normally open

door contacts

+ ---

For this application select

Trigger “CHG”, Relay “OFF”.

For this application select

Trigger “CHG”, Relay “OFF”.

Dry

relay

output Advance

CNC NO

POWER

12-24

VDC/VAC

Dry

Trigger

IN1

Confirm

Normally open or

normally closed

switch contacts

Door Contacts

Protective Circuit

+ ---

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

Fig. 6 - Timed Shunt for a Door. Use to bypass alarm contacts.

- 8 - Tempo2 Installation Guide

Dry

relay

output Advance

CNC NO

POWER

12-24

VDC/VAC

Dry

Trigger

IN1

Confirm

Normally open or

normally closed

switch contacts

--

+

+ ---

For this application select

Trigger “CHG”, Relay “PULSE”.

Dry

relay

output Advance

CNC NO

POWER

12-24

VDC/VAC

Dry

Trigger

IN1

Confirm

DIALER OR

TRANSMITTER

+ ---

Tempo2 Typical Applications (cont’d):

Fig. 7 - Delayed Egress:

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

Fig. 8 - Test Timer:

Altronix is not responsible for any typographical errors.

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056

website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty

IITempo2 I22U MEMBER

Tempo 2 One Shot or Test Timer Installation guide

This manual is also suitable for

Tempo 2 One Shot or Test Timer Installation guide

Other documents