2. MGC
  3. ANC-6000
ANC-6000

MGC ANC-6000 User manual

  • Hello! I am an AI chatbot trained to assist you with the MGC ANC-6000 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
LT-6685 Rev 0 Dec 2022 Page 1 of 3
ANC-6000
Audio Network Controller Board
Installation Instructions
Module Mounting Locations
The ANC-6000 Audio Network Controller board is mounted in the center position over the FX-6000MNS-CH main fire alarm
board as shown in Figure 1. If a TNC-5000 Telephone Controller board is used, it is mounted over the ANC-6000.
Figure 1 Mechanical Installation for the ANC-6000 Audio Network Controller Board
1234
TNC-5000
ANC-6000
FNC-2000
ANC-6000
TNC-5000
TNC-5000
TNC-5000 board
mounts over
ANC-6000 board
Mounting
holes
LT-6685 Rev 0 Dec 2022 Page 2 of 3
Figure 2 ANC-6000 Audio Network Controller Board Layout
DIP Switch Settings for SW1 on the ANC-6000 Board
Addresses available for the ANC-6000 (per node) are set as noted in the following table.
ANC-6000 Address Setting (DIP SWITCH SW1)
ANC-6000
ADDR SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8
1 ON OFF OFF OFF OFF OFF OFF OFF
2 OFF ON OFF OFF OFF OFF OFF OFF
3 ON ON OFF OFF OFF OFF OFF OFF
4 OFF OFF OFF OFF OFF ON OFF OFF
5 OFF OFF OFF OFF OFF ON OFF ON
6 OFF OFF OFF OFF OFF ON ON OFF
7 OFF OFF OFF OFF OFF ON ON ON
ON
+ −
+ S −
+ −
+ −
P5
P3 Connect to main re
alarm board P16 if using
Digital Audio and/or Phone
Remote Mic
Connects to P10 on TNC-5000
Telephone Network Controller
Module
Connect
RS-485 cable
from P3 on the
main re alarm
board to P2 IN
on this board
(daisy chain
fashion) and
from P1 OUT to
next main re
alarm board or
to next
FNC-2000
Connect power cable from
P8 on the main re alarm
board to P6 on this board
(daisy chain fashion) and
from P5 OUT to next main
re alarm board or to next
ANC-6000
DIP Switch SW1 is factory set
at address one, SW1-1 ON.
Refer to the table below for all
DIP switch address settings.
FPGA JTAG
Factory use
Aux Audio
Ribbon Cable to
P2 on QCC-6000
JW4 Jumper
factory use only,
leave closed (on)
Not used
JW3 Jumper
factory use only,
leave open (o)
Factory use
For debugging
only
CN1
P8
P7
P11
JW3
JW4
LT-6685 Rev 0 Dec 2022 Page 3 of 3
ANC-6000 Wiring
The auxiliary audio input has a maximum input of 1 VRMS. The transformer is isolated on the ANC-6000.
Connect an audio source, for example background music or paging, to the SIG terminal. Connect a normally open relay
and 3.9 kΩ resistor to the CTL terminal as shown in Figure 3. Short the relay to activate the auxiliary audio.
Figure 3 ANC-6000 Wiring Diagram
+ −
+ −
+ −
+ −
CTL
SIG
AUX AUDIO
RS-485
SIG
REMOTE MIC
To RS-485 IN on
QMP-6101NV
3.9 kΩ
N.O. RELAY
AUDIO SOURCE
Short this relay to activate
the audio sou
rce
To MIC IN on
QMP-6101NV
S
Paging
Microphone
Paging Microphone
/