2. MGC
  3. ANC-6000
ANC-6000

MGC ANC-6000 User manual

  • Hello! I've reviewed the MGC installation instructions for the ANC-6000 Audio Network Controller, TNC-5000 Telephone Controller and their related components. This document details mounting locations, wiring for auxiliary audio inputs, and RS-485 communication. I'm ready to answer your questions about setting up these devices.
  • Where is the ANC-6000 board mounted?
    Where is the TNC-5000 board mounted?
    What is the maximum input for the auxiliary audio?
    How to activate auxiliary audio?
LT-6685 Rev 0 Nov 2022 Page 1 of 3
ANC-6000
Audio Network Controller Board
Installation Instructions
Module Mounting Locations
The ANC-6000 Audio Network Controller board is mounted in the center position over the FX-6000MNS-CH main fire alarm
board as shown in Figure 1. If a TNC-5000 Telephone Controller board is used, it is mounted over the ANC-6000.
Figure 1 Mechanical Installation for the ANC-6000 Audio Network Controller Board
1234
TNC-5000
ANC-6000
FNC-2000
ANC-6000
TNC-5000
TNC-5000
TNC-5000 board
mounts over
ANC-6000 board
Mounting
holes
LT-6685 Rev 0 Nov 2022 Page 2 of 3
Figure 2 ANC-6000 Audio Network Controller Board Layout
DIP Switch Settings for SW1 on the ANC-6000 Board
Addresses available for the ANC-6000 (per node) are set as noted in the following table.
ANC-6000 Address Setting (DIP SWITCH SW1)
ANC-6000
ADDR SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8
1 ON OFF OFF OFF OFF OFF OFF OFF
2 OFF ON OFF OFF OFF OFF OFF OFF
3 ON ON OFF OFF OFF OFF OFF OFF
4 OFF OFF OFF OFF OFF ON OFF OFF
5 OFF OFF OFF OFF OFF ON OFF ON
6 OFF OFF OFF OFF OFF ON ON OFF
7 OFF OFF OFF OFF OFF ON ON ON
ON
+ -
+ S -
+ -
+ -
P5
P3 Connect to main re
alarm board P16 if using
Digital Audio and/or Phone
Remote Mic
Connects to P10 on TNC-5000
Telephone Network Controller
Module
Connect
RS-485 cable
from P3 on the
main re alarm
board to P2 IN
on this board
(daisy chain
fashion) and
from P1 OUT to
next main re
alarm board or
to next
FNC-2000
Connect power cable from
P8 on the main re alarm
board to P6 on this board
(daisy chain fashion) and
from P5 OUT to next main
re alarm board or to next
ANC-6000
DIP Switch SW1 is factory set
at address one, SW1-1 ON.
Refer to the table below for all
DIP switch address settings.
Factory use
Aux Audio
Ribbon Cable to
P1 on QCC-6000
JW4 Jumper
factory use only,
leave closed (on)
Future use
P7
JW3 Jumper
factory use only,
leave open (o)
Factory use
For debugging
only
LT-6685 Rev 0 Nov 2022 Page 3 of 3
ANC-6000 Wiring
The auxiliary audio input has a maximum input of 1 VRMS. The transformer is isolated on the ANC-6000.
Connect an audio source, for example background music or paging, to the SIG terminal. Connect a normally open relay
and 3.9 kΩ resistor to the CTL terminal as shown in Figure 3. Short the relay to activate the auxiliary audio.
Figure 3 ANC-6000 Wiring Diagram
+ -
+ -
+ -
+ -
CTL
SIG
AUX AUDIO
RS-485
SIG
REMOTE MIC
To RS-485 IN on
QMP-6101NV
3.9 kΩ
N.O. RELAY
AUDIO SOURCE
Short this relay to activate
the audio sou
rce
To MIC IN on
QMP-6101NV
S
Paging
Microphone
Paging Microphone
/