COOSPO BC200 is an advanced cycling computer that provides comprehensive data and features to enhance your riding experience. With its GPS capabilities, it accurately tracks your speed, distance, and altitude, allowing you to monitor your progress and performance. Additionally, it connects to various sensors, including heart rate monitors, cadence sensors, and power meters, to provide detailed insights into your workout metrics.
COOSPO BC200 is an advanced cycling computer that provides comprehensive data and features to enhance your riding experience. With its GPS capabilities, it accurately tracks your speed, distance, and altitude, allowing you to monitor your progress and performance. Additionally, it connects to various sensors, including heart rate monitors, cadence sensors, and power meters, to provide detailed insights into your workout metrics.
USER MANUAL
All About Passio n
BC200-RTN-I1-2220
SCAN for more
詳しくはこちら
Nach mehr SUCHEN
SCANNEZ pour plus
ESCANEAR para más
Cerca altro
Görüntülemek için tarayın
Button function
Up OK
During the cycling,
press it to mark the lap
Back
During the cycling,
press it to pause
Long press to turn on
/off back light
GPS Temperature & Battery level
Time
Down Table
User Sensor History
Sync SettingGPS
Cycling Bike
- 2 -
Long press to turn off
the device Short press
to turn on the device
(Automatically shuts
down after 10 minutes
of inactivity when not
in motion)
Standby long press: enter
Bluetooth synchronization
Standby long press (start
to enter USB synchronize)
Icons
Icon Description
GPS signal status/Icon flashing
means acquiring satellite signals
It's available to scroll the page up
and down by pressing the button
IIt's not available to scroll the
page up and down by pressing
the button
Bluetooth accessory
ANT+ accessory
Heart rate monitor: The icon is
on when connected / The icon is
flashing when the sensor is
disconnected or under searching
Icon Description
Power meter: The icon is on when
connected / The icon is flashing
when the sensor is disconnected
or under searching
Satellite signals available
No satellite signal
Battery level
Paused
Auto Pause
- 3 -
Speed sensor: The icon is on when
connected/The icon is flashing
when the sensor is disconnected
or under searching
Cadence sensor: The icon is on
when connected/The icon is
flashing when the sensor is
discon nected or under searching
Standby long press: enter
Bluetooth synchronization
Standby long press (start
to enter USB synchronize)
Standard Accessories
Table
User Sensor History
Sync SettingGPS
Cycling Bike
G
28 C
12
:
35
Main Device x1 Charging Cable x1 User Manual x1
Rubber Pad
for Out Front
Mount x2
Out Front Bike Mount x1
Standard
Bike
Mount x1
Rubber Pad
for Standard
Bike Mount x1
Rubber Ring
(Big x 2, Small x 2)
Screw
Wrench x1
- 4 -
Standard Mount Installation
a
How to Install
Install the rubber pad
onto the mount
Install the main device
onto the mount
Rotate the main device for
90 degrees Installation completed
Tie the mount onto the bar
with the rubber rings Tie up the mount
- 5 -
Install the rubber pad
onto the handle bar
Install the main device
onto the mount
Rotate the main device
for 90 degrees Installation completed
Unscrew the screw in
the mount
Install the mount onto the
handle bar on the rubber
pad, tighten up the screw
Out front mount installation
b
- 6 -
Charging
USB DC 5V power adaptor / Computer
Please charge the device before first time use.
1
Please use DC 5V power adapter for charging.
2
During the charging, the battery icon will flash until fully charged.
3
- 7 -
The product has a built-in battery. Do not throw the product into a fire. Please
choose an adapter that meets the rated voltage of the device to charge the
device to avoid damage to the device.
Open the rubber
cover, connect
the device with
usb cable to
charge
Initial Setup
Language
简体中文
English
Table
User Sensor History
Sync SettingGPS
Cycling Bike
G
28 C
Gender Male
Age 18
Height 175cm
User Info
Weight 70kg
Age 18
Height 175cm
User Info
Weight 70kg
Gender Male
Female
Male
For the 1st time use, please select the language before use.
1
User Profile Setting (To make the exercise calculation more
accurate, please set the user profile correctly)
2
- 8 -
Total Distance: Select and confirm to reset the total distance
Spd Source: Set the priority for the source of the speed
Table
User Sensor History
Sync SettingGPS
Cycling Bike
G
28 C
Bike 2
Bike
Bike 3
Weight 12.5kg
2096mm
0km
Wheel
Total Distance
Spd Source Spd&Cad
Activate
Bike 1
On
Bike 1 On
Bike Profile Setting.
3
- 9 -
Common wheel size and circumference(Wheel Size L (mm))
- 10 -
Speed sensor: The icon is on when
connected/The icon is flashing
when the sensor is disconnected
or under searching
12 × 1.75 935mm
14 × 1.5 1020mm
14 × 1.75 1055mm
16 × 1.5 1185mm
16 × 1.75 1195mm
18 × 1.5 1340mm
18 × 1.75 1350mm
20 × 1.75 1515mm
20 × 1-3/8 1615mm
22 × 1-3/8 1770mm
22 × 1-1/2 1785mm
24 × 1 1753mm
24×3/4 Tubular 1785mm
24 × 1-1/8 1795mm
24 × 1-1/4 1905mm
24 × 1.75 1890mm
26 × 1.40 2005mm
26 × 1.50 2010mm
27 × 1 2145mm
27 × 1-1/8 2155mm
27 × 1-1/4 2161mm
27 × 1-3/8 2169mm
27.5×1.75 2114mm
27.5×2.125 2174mm
27.5×1.5 2074mm
27.5×1.95 2146mm
29×2.1 2288mm
29×2.2 2298mm
29×2.3 2326mm
650× 35A 2090mm
650 × 38A 2125mm
650 × 38B 2105mm
24 × 2.00 1925mm
24 × 2.125 1965mm
26 × 1.75 2023mm
26 × 1.95 2050mm
26 × 2.00 2055mm
26 × 2.10 2068mm
26 × 2.125 2070mm
26 × 2.35 2083mm
26 × 3.00 2170mm
26 × 7/8 1920mm
26 × 1(59) 1913mm
26 × 1(65) 1952mm
26 × 1.25 1953mm
26 × 1-1/8 1970mm
26 × 1-3/8 2068mm
26 × 1-1/2 2100mm
700 × 18C 2070mm
700 × 19C 2080mm
700 × 20C 2086mm
700 × 23C 2096mm
700 × 25C 2105mm
700 × 28C 2136mm
700 × 30C 2170mm
700 × 32C 2155mm
700C Tubular 2130mm
700 × 35C 2168mm
700 × 38C 2180mm
700 × 40C 2200mm
700 × 42C 2224mm
700 × 44C 2235mm
700 × 45C 2242mm
700 × 47C 2268mm
Other Settings
Table
User Sensor History
Sync SettingGPS
Cycling Bike
G
28 C
Zone:
Set the value for each heart rate zones, power zones, and cadence
zones
Alarm:
Set the alarm for heart rate, power and cadence. The device will
beep if it reached to the preset value, and a warning message will
pop up during the cycling.
Smart Pause:
When this function is turned on, the cycling recording will be
paused automatically when the speed is 0. It will get resumed
when the speed is detected.
Altitude:
Set the numbers here to calibrate the current altitude.
Smart Lap:
Set the location or the distance used for smart lap counting.
Tone:
Set the key tone and the warning tone.
Back Light:
Set the mode of how to turn the back light off and the brightness .
- 11 -
Unit:
Set the unit to Metric System or Imperial System.
Time:
Set time format 12/24; time zone setting.
Language:
Set language.
Storage:
Data overwrite setting; clear history record.
Factory Reset:
Factory reset and wipe all data.
About:
Check Ant+ ID, firmware and hardware version.
- 12 -
Page Setting
Manual
10 Sec
15 Sec
20 Sec
Self-defined parameter could be set in Data Page 1~5
Data Page 2
Data Page 3
Data Page 4
Data Page 5
Data Page
Data Page 1 Off
Off
Off
Off
Off
Display Manual
Switch/Sec
2 0
Table
User Sensor History
Sync SettingGPS
Cycling Bike
G
28 C
Set the display content in page setting.
1
- 13 -
Speed
Time
Distance
Cadence
Power
Altitude
Temp
Data Fields
HR
Heart Rate
Max.HR
%Max.HR
%LTHR
Lap.Avg.HR
Lap.Max.HR
L.Lap.Avg.HR
Avg.HR
Speed
Time
Distance
Cadence
Power
Altitude
Temp
Data Fields
HR
Max.HR
%Max.HR
%LTHR
Lap.Avg.HR
Lap.Max.HR
L.Lap.Avg.HR
Avg.HR
Data Page 1
Distance
Heart Rate
Power
Altitude
Cadence
Grade
Speed
Time.Move
Data Fields 9
Calorie
On
Data Page
9
Heart Rate
Data Fields
Select the parameter to be displayed
The content to be displayed in self-defined page.
2
- 14 -
Number of parameters
to be displayed
- 15 -
Connecting the Sensors
Please make sure the sensors are in wake-up mode( for example the heart rate monitor
should be worn properly, for cadence, speed, and power sensor, rotate the crank or the
wheel to wake it up).
Select the desired
type of sensor for
connection
select scanned
sensors to pair
with the sensor
Speed
Spd&Cad
Power
HeartRate
踏频
Bike 1
Activate Off
Cadence
Bike 2
Sensor Manage
Bike 3
Bike 1 On
Table
User Sensor History
Sync SettingGPS
Cycling Bike
G
28 C
Search...
HRM803-ABC
ID:1234567，-35dB
ID 1234567
ID 1234567
HRM803-123
HRM803-25564656...
You can set 3 bikes
for the sensor
selection
Connection completed
Select the desired sensor, and then select to connect
new sensor or turn off the old sensor in the popped up
window
Add New Sensor and Turn off Old Sensor
Bike 1
Activate On
ID 1234567
Speed
Spd&Cad
Power
HeartRate
Cadence
Bike 1
踏频
Activate On
ID 1234567
Speed
Spd&Cad
Power
HeartRate
Cadence
Turn Off
Connect New
- 16 -
Select Power, and then select Calibrate in the popped up window
Power Calibration
Power calibration only works in
ANT+ power meter, the Bluetooth
power meter doesn't support this
function
Bike 1
Activate On
ID 1234567
ID 1234567
Speed
Spd&Cad
Power
HeartRate
Cadence
Turn On
Connect New
Calibrate
Current Value
Calibrating
150
Power Calibrate
150
- 17 -
Starting a Ride
Once the device is turned
on, it will automatically
search for satellite signals,
it may take 15~90 seconds
to acquire signals. Please
make sure you acquire the
satellite signal for the first
time use
Locating for
the first time
Connect with
phone
sync time first
Table
User Sensor History
Sync SettingGPS
Cycling Bike
G
28 C
Distance
Heart Rate
Power
Temp
c
Time.Move
Cadence
Altitude
Calorie
Speed
23.2
9.20
133
293
23.0223
82
93
00:23:43
m
r
p
m
b
p
m
w
c
a
l
- 18 -
During the cycling, Press
it to mark the lap
Scroll up and
down in the
display During the cycling, Press
it to pause
Display and Button
Distance
Heart Rate
Power
Temp
c
Time.Move
Cadence
Altitude
Calorie
Speed
23.2
9.20
133
293
23.0223
82
93
00:23:43
m
r
p
m
b
p
m
w
c
a
l
- 19 -
Accessories Connection Status.
(The icon will blink when the
accessory is disconnected, and it
will be on when the accessory is
connected)
View History
Press the button
to scroll up and down
Table
User Sensor History
Sync SettingGPS
Cycling Bike
G
28 C
History
Page 1/7
2019/10/21 16:35
2019/10/21 16:35
2019/10/21 16:35
2019/10/21 16:35
2019/10/21 16:35
2019/10/21 16:35
2019/10/21 16:35
Total 45
2019/10/21 16:35
Datails
Lap Data
Delete
Power Max 650 w
Avg 125 w
Move Time 00:02：36
Distance
Heart Rate
98.5 km
Max 185 bpm
Avg 125 bpm
Speed Max 76km/h
Avg 39km/h
Candence Max 65 rpm
Avg 35 rpm
2019/01/06 14:36
Page 1/2
- 20 -
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
COOSPO BC200 is an advanced cycling computer that provides comprehensive data and features to enhance your riding experience. With its GPS capabilities, it accurately tracks your speed, distance, and altitude, allowing you to monitor your progress and performance. Additionally, it connects to various sensors, including heart rate monitors, cadence sensors, and power meters, to provide detailed insights into your workout metrics.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Bryton Amis S430 User manual
-
-
-
-
Polar Electro M450 User manual
-
Bryton Cardio 40 User manual
-
Polar M460 User manual
-
Giant NeosTrack User manual
-
Garmin Edge® 830 Mountain Bike Bundle User manual
-
Garmin Edge 530 Owner's manual