Campbell Hausfeld HV2002 User manual

Category
Paint Sprayer
Type
User manual
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
IN206600AV 2/03
Operating Instructions & Parts Manual
HV2000 and HV3000 Series
HVLP
Turbine
BUILT TO LAST
Description
Campbell Hausfeld HVLP turbines are
designed to generate a High Volume of
Low Pressure air for operating HVLP
spray guns. These turbines operate
differently than air compressors
because turbines do not require an air
tank to hold compressed air. Since
there is no compression of air, HVLP
turbines do not create condensation in
the air hoses as compressors often do.
Consequently, the project is not at risk
of condensation contaminating the
coating material. The air generated by
the turbine is generally warm due to
the air working in the turbine. The
warm air can be a benefit for
accelerating drying in less than ideal
weather conditions and for drying the
spray gun components. HVLP turbines
are portable, can be plugged into
standard outlets and operate and
sound similar to shop-vacs.
Unpacking
When unpacking the unit, inspect
carefully for any damage that may
have occurred during transit. Make
sure any loose fittings, bolts, etc., are
tightened before putting sprayer into
service. Each unit has been tested
before shipment. Do not readjust or
modify the turbine components.
Specifications
MODEL HV2000
CFM . . . . . . . .54 CFM at turbine outlet
Operating Pressure . . . . . . . .4 PSI Max.
Motor Type . . . . . . .Brush type, 2 stage,
. . . . . . . . . . . . . . . . . . . . . . . .Tangential
Hose Length . . . . . . .15 ft. (30 ft. Max.)
Transfer Efficiency . . . . . . . . .86% Max.
Weight . . . . . . . . . . . . . . . . . .15 Pounds
Voltage . . . . . . . . . . . . .120V, 10.1 Amp
Stub Hose . . . . . . . . . . . . . . . . . . . . . .No
Storage Compartment . . . . . . . . . . .Yes
MODEL HV2500
CFM . . . . . . . .58 CFM at turbine outlet
Operating Pressure . . . . . . . .5 PSI Max.
Motor Type . . . . . . .Brush type, 2 stage,
. . . . . . . . . . . . . . . . . . . . . . . .Tangential
Hose Length . . . . . . .25 ft. (40 ft. Max.)
Transfer Efficiency . . . . . . . . .86% Max.
Weight . . . . . . . . . . . . . . . . . .26 Pounds
Voltage . . . . . . . . . . . . . .120V, 11 Amp
Stub Hose . . . . . . . . . . . . . . . . . . . . . .Yes
Storage Compartment . . . . . . . . . . .Yes
MODEL HV3000
CFM . . . . . . . .65 CFM at turbine outlet
Operating Pressure . . . . . . . .6 PSI Max.
Motor Type . . . . . . .Brush type, 3 stage,
. . . . . . . . . . . . . . . . . . . . . . . .Tangential
Hose Length . . . . . . .25 ft. (50 ft. Max.)
Transfer Efficiency . . . . . . . . .86% Max.
Weight . . . . . . . . . . . . . . . . . .28 Pounds
Voltage . . . . . . . . . . . . .120V, 13.8 Amp
Stub Hose . . . . . . . . . . . . . . . . . . . . . .Yes
Storage Compartment . . . . . . . . . . .Yes
COMPONENTS
(1) Turbine
(1) Hose and quick connect fitting
assemble and clean the unit (storage
compartment)
(1) Wrench - the only tool needed to
assemble and clean the unit (storage
compartment)
(1) Viscosity stick storage compartment)
(1) Cleaning brush ( storage compartment)
Attention: Campbell Hausfeld recommends that servicing other than that shown in the instruction manual should be
performed by an authorized service facility. NOT INTENDED FOR CONTINUOUS USE.
© 2003 Campbell Hausfeld/Scott Fetzer
For parts, product & service information
visit www.chpower.com
See Warranty on page 4 for important information about commercial use of this product.
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
2
Operating Instructions and Parts Manual
General Safety
Danger means a
hazard that will
cause death or serious injury if the
warning is ignored.
Warning means a
hazard that could
cause death or serious injury if the
warning is ignored.
Caution means a
hazard that may
cause minor or moderate injury if the
warning is ignored. It also may mean a
hazard that will only cause damage to
property.
NOTE: Note means any additional
information pertaining to the product
or its proper usage.
Read all instructions and safety
precautions before operating the unit.
Risk of fire or explosion!
Solvent and paint fumes
can explode or ignite,
causing severe injury and
property damage.
Paints and solvents containing
HALOGENATED HYDROCARBONS can
react explosively with aluminum.
Always check the product’s label
before using these materials in the
unit.
Make sure the room is well-ventilated.
Avoid all ignition sources, such as static
electricity sparks, open flames, hot
objects, sparks from connecting and
disconnecting power cords, and
working light switches.
Follow the material and solvent
manufacturers’ safety precautions and
warnings. Do not use liquids with flash
points less than 100 degrees Fahrenheit
(38 degrees Celsius).
Do not carry TURBINE while spraying.
Keep the turbine at the maximum
distance from the spraying area.
Static electricity can be produced by
HVLP spraying. Make sure any
electrically conductive object being
sprayed is grounded to prevent static
sparking. The sprayer is grounded
through the electric cord. If an
extension cord is necessary, the cord
!
WARNING
!
CAUTION
!
WARNING
!
DANGER
must be a grounded, 115 volt, three
wire type cord.
Hazardous vapors: Paints,
solvents, insecticides, and
other materials may be
harmful if inhaled,
causing severe nausea,
fainting, or poisoning.
Use a respirator or mask whenever
there is a chance that vapors may be
inhaled. Read all instructions with the
mask to ensure that the mask will
provide the necessary protection
against the inhalation of harmful
vapors.
NEVER point the spray gun at any part
of the body, or at anyone else.
Tipping the gun causes the gun to clog.
Dried spray material also clogs the
pressure delivery tube and fittings. The
spray gun does not function when
clogging occurs.
When not in use, be sure to disconnect
the hose and place the gun on a solid,
level surface to avoid tipping.
GROUNDING INSTRUCTIONS
This product must be properly
grounded. In the event of an electrical
short circuit, grounding reduces the risk
of electrical shock by providing an
alternate path for the electrical current.
This product is equipped with a cord
that has a ground wire and an
appropriate ground plug. Plug the unit
into an outlet that is properly installed
and grounded in accordance with local
codes and ordinances.
Improper installation of
the ground plug can
result in the risk of
electrical shock. If repair
or replacement of the plug or cord is
necessary, do not connect the ground
wire to either flat blade terminal. The
wire with green insulation (with or
without a yellow stripe) is the
grounding wire.
1. For any question regarding proper
installation of the ground plug,
consult a qualified (licensed or
certified) electrician.
!
DANGER
!
CAUTION
2. Do not modify the plug provided. If
the plug does not fit the outlet,
have the proper outlet installed by a
qualified electrician.
3. This product is for use on a nominal
120-volt circuit and has a grounding
plug that looks like the plug in
Figure 2. Make sure that the
product is connected to an outlet
having the same configuration as
the plug. No adapters should be
used with this product.
Figure 2 - Grounding Plug
4. If an extension cord is required, use
only a three wire extension cord
that has the same configuration as
the unit cord, including the (round)
ground terminal. Make sure that
the extension cord is plugged into a
properly grounded receptacle.
5. When using an extension cord, be
sure it is in good condition and
heavy enough to meet the
specifications in the chart below. If
an extension cord is needed, the
following wire sizes must be used
(See Chart 1).
Chart 1 Extension Cord Requirements
For Information About
This Product
Call 1-800-626-4401
25’ cord . . . . . . . .10,12, or 14 Gauge
50’ cord . . . . . . . . . . .10 or 12 Gauge
100’ cord . . . . . . . . . . . . . . .10 Gauge
TEST
RESET
Grounding
Pin
www.chpower.com
3
Operating Instructions and Parts Manual
Maintenance
Be sure the air filter is clean. A dirty air
filter restricts air flow and can cause the
motor to overheat.
IMPORTANT: Keep the unit at the
maximum distance from the spray area
to extend filter life.
Figure 3
Troubleshooting Chart
Symptom Possible Cause(s) Corrective Action
Poor air flow
Unusual grinding noise
1. Hose restricted or kinked
2. Restricted filter
Damaged turbine motor
1. Keep air hose straight
2. Clean or replace filter
Contact Service Center
Replacement Parts List
1 Filter MP3021 1
Filter pack HV012600AJ HV012600AJ 2
2 Hose 15’ MP3106 1
Hose 25’ HV012500AJ HV012500AJ 1
3 Quick connect coupler HV002200AV HV002200AV HV002200AV 1
4 Stub hose HA222503AV HA222503AV 1
Ref
Part Number For Model Number
No. Description HV2000 HV2500 HV3000 Qty
MODEL HV2000
1. Remove the filter grille thumbscrew
with a screw driver to access the
filter (See Figure 3).
2. Clean the filter with mild soapy
water and pat dry.
3. Replace filter if built-up with paint.
MODEL HV2500 AND HV3000
1. Squeeze and pull to remove both
filters (See Figure 4).
2. Clean the filter with mild soapy
water and pat dry or replace filter if
built-up with paint.
3. Squeeze and tuck to install filter.
For Information About This Product
Call 1-800-626-4401
1
3
2
3
4
1
2
Model HV2000
Models HV2500 or HV3000
Figure 4
Filter
Housing
Thumbscrew
Accessories
1 5' Whip Hose (Use with any model) HV012400AJ 1
2 Multi-Purpose Case HV7008 1
Ref
No. Description Part Number Qty
www.chpower.com
4
Operating Instructions and Parts Manual
Limited Warranty
1. DURATION: From the date of purchase by the original purchaser as follows: Standard Duty Paint Application Systems and
all Paint Application Accessories - 1 year, Serious Duty Paint Application Systems - 3 years, Extreme Duty Paint Application
Systems - 5 years.
2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld/A Scott Fetzer Company, 100 Production Drive, Harrison,
Ohio, 45030, Telephone: 1-800-626-4401.
3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale or rental) of the
Campbell Hausfeld Product.
4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: All non-compressor driven paint application systems, HVLP spraying
systems, and paint application accessories supplied or manufactured by the Warrantor.
5. WHAT IS COVERED UNDER THIS WARRANTY: Defects in material and workmanship which occur within the duration of the
warranty period. Warrantor will also cover normal wear items for a period of thirty days from the date of original purchase
against defects in material and workmanship. These wear items are: HVLP-filters, motor brushes, gun packing, gun
canister seal, gun check valve and gun air flow ring; Airless-inlet valve, outlet valve, gun valve, filters, tips, all seals and o-
rings.
6. WHAT IS NOT COVERED UNDER THIS WARRANTY:
A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM
THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If standard duty product is used for commercial or
industrial purposes, the warranty will apply for ninety (90) days from the date of original purchase. If product is used
for rental purposes, the warranty will apply for ninety (90) days from the date of original purchase. Some states do not
allow limitation on how long an implied warranty lasts, so the above limitations may not apply to you.
B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE , OR EXPENSE THAT MAY RESULT FROM ANY
DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
C. Any failure that results from an accident, purchasers abuse, neglect or failure to operate products in accordance with
instructions provided in the owners manual(s) supplied with product. Accident, purchasers abuse, neglect or failure to
operate products in accordance with instructions shall also include the removal or alteration of any safety devices. If
such safety devices are removed or altered, this warranty is void.
D. Normal adjustments which are explained in the owners manual(s) provided with the product.
E. Items or services that are normally required to maintain the product: HVLP-filters, motor brushes, gun packing, gun
canister seal, gun check valve and gun air flow ring; Airless-inlet valve, outlet valve, gun valve, filters, tips, all seals and
o-rings., or any other expendable part not specifically listed, will only be covered for thirty days from date of original
purchase.
7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantors option, products or
components which are defective, have malfunctioned and/or failed to conform within duration of the warranty period.
8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:
A. Provide dated proof of purchase and maintenance records.
B. Deliver or ship the Campbell Hausfeld product or component to the nearest Campbell Hausfeld Authorized Service
Center. Freight costs, if any, must be borne by the purchaser.
C. Use reasonable care in the operation and maintenance of the products as described in the owners manual(s).
9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be
scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of
replacement parts.
This Limited Warranty applies in the U.S., Canada and Mexico only and gives you specific legal rights. You may also have
other rights which vary from state to state, or country to country
.
www.chpower.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Campbell Hausfeld HV2002 User manual

Category
Paint Sprayer
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI