Yamaha 2012 Road Star S Owner's manual

DIC183

1BH-28199-12

XV17ASB(C)

XV17ATSB(C)

OWNER’S MANUAL

Read this manual carefully before operating this vehicle.

LIT-11626-25-28

EAU10042

Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.

U1BH12E0.book Page 1 Wednesday, July 6, 2011 4:06 PM

INTRODUCTION

EAU10083

Congratulations on your purchase of the Yamaha Road Star™. This model is the result of Yamaha’s vast experience in the

production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and

reliability that have made Yamaha a leader in these fields.

This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle. If you

have any questions concerning the operation or maintenance of your motorcycle, please consult a Yamaha dealer.

The design and manufacture of this Yamaha motorcycle fully comply with the emissions standards for clean air applicable at

the date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of the

motorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the

recommended maintenance schedules and operating instructions contained within this manual.

Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most cur-

rent product information available at the time of printing, there may be minor discrepancies between your motorcycle and this

manual. If there is any question concerning this manual, please consult a Yamaha dealer.

WARNING

EWA10011

Please read this manual and the “YOU AND YOUR MOTORCYCLE: RIDING TIPS” booklet carefully before operating

this motorcycle. Do not attempt to operate this motorcycle until you have attained adequate knowledge of its con-

trols and operating features. Regular inspections and careful maintenance, along with good operating techniques,

will help ensure that you safely enjoy the capabilities and reliability of this motorcycle.

U1BH12E0.book Page 1 Wednesday, July 6, 2011 4:06 PM

IMPORTANT MANUAL INFORMATION

EAU10133

Particularly important information is distinguished in this manual by the following notations:

*Product and specifications are subject to change without notice.

This is the safety alert symbol. It is used to alert you to potential personal injury

hazards. Obey all safety messages that follow this symbol to avoid possible injury

or death.

A WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

A NOTICE indicates special precautions that must be taken to avoid damage to the

vehicle or other property.

A TIP provides key information to make procedures easier or clearer.

WARNING

NOTICE

TIP

U1BH12E0.book Page 1 Wednesday, July 6, 2011 4:06 PM

IMPORTANT MANUAL INFORMATION

EAU10193

XV17ASB(C)/XV17ATSB(C)

OWNER’S MANUAL

1st edition, June 2011

Any reprinting or unauthorized use

without the written permission of

Yamaha Motor Corporation, U.S.A.

is expressly prohibited.

Printed in Japan.

P/N LIT-11626-25-28

U1BH12E0.book Page 2 Wednesday, July 6, 2011 4:06 PM

TABLE OF CONTENTS

LOCATION OF IMPORTANT

LABELS .............................................1-1

SAFETY INFORMATION ..................2-1

DESCRIPTION ..................................3-1

Left view ..........................................3-1

Right view........................................3-3

Controls and instruments.................3-5

INSTRUMENT AND CONTROL

FUNCTIONS .......................................4-1

Main switch/steering lock ................4-1

Indicator lights and

warning lights ..............................4-2

Multi-function meter unit .................4-3

Handlebar switches ........................4-6

Clutch lever .....................................4-8

Shift pedal .......................................4-8

Brake lever .....................................4-8

Brake pedal ....................................4-9

Fuel tank cap ..................................4-9

Fuel ...............................................4-10

Fuel tank breather/overflow

hose ..........................................4-11

Catalytic converters ......................4-11

Locking the steering with

a padlock ...................................4-12

Rider seat .....................................4-12

Helmet holder ...............................4-13

Windshield [XV17ATSB(C)]...........4-14

Sidecases [XV17ATSB(C)] ........... 4-15

Adjusting the shock absorber

assembly ................................... 4-16

Sidestand ..................................... 4-17

Ignition circuit cut-off system ........ 4-18

Auxiliary DC connector .................4-20

FOR YOUR SAFETY –

PRE-OPERATION CHECKS ............. 5-1

OPERATION AND IMPORTANT

RIDING POINTS................................. 6-1

Starting the engine .........................6-1

Shifting ........................................... 6-2

Engine break-in .............................. 6-3

Parking ........................................... 6-4

PERIODIC MAINTENANCE AND

ADJUSTMENT ................................... 7-1

Owner’s tool kit ............................... 7-2

Periodic maintenance chart for

the emission control system ....... 7-3

General maintenance and

lubrication chart .......................... 7-5

Removing and installing panels ..... 7-9

Checking the spark plugs ............. 7-10

Canister (for California only) ........ 7-11

Engine oil and oil filter cartridge ... 7-12

Transfer case oil ........................... 7-15

Cleaning the air filter element ...... 7-16

Checking the throttle grip free

play ........................................... 7-18

Valve clearance ........................... 7-18

Tires ............................................. 7-19

Cast wheels ................................. 7-20

Adjusting the clutch lever free

play ........................................... 7-21

Adjusting the brake lever free

play ........................................... 7-22

Brake light switches ..................... 7-22

Checking the front and

rear brake pads ........................ 7-23

Checking the brake fluid level ...... 7-23

Changing the brake fluid .............. 7-25

Drive belt slack ............................ 7-25

Checking and lubricating

the cables ................................. 7-26

Checking and lubricating

the throttle grip and cable ......... 7-26

Checking and lubricating

the brake and shift pedals ........ 7-27

Checking and lubricating

the brake and clutch levers ...... 7-27

Checking and lubricating

the sidestand ............................ 7-28

Lubricating the swingarm

pivots ........................................ 7-28

Lubricating the rear suspension ... 7-29

Checking the front fork ................. 7-29

Checking the steering .................. 7-30

Checking the wheel bearings ....... 7-30

U1BH12E0.book Page 1 Wednesday, July 6, 2011 4:06 PM

TABLE OF CONTENTS

Battery ..........................................7-30

Replacing the fuses ......................7-32

Replacing the headlight bulb ........7-33

Tail/brake light ..............................7-34

Replacing a turn signal light

bulb ...........................................7-35

Replacing a license plate light

bulb ...........................................7-35

Supporting the motorcycle ............7-36

Troubleshooting ............................7-37

Troubleshooting chart ...................7-38

MOTORCYCLE CARE AND

STORAGE ..........................................8-1

Matte color caution .........................8-1

Care ................................................8-1

Storage ...........................................8-4

SPECIFICATIONS .............................9-1

CONSUMER INFORMATION...........10-1

Identification numbers ..................10-1

Reporting safety defects ...............10-3

Motorcycle noise regulation ..........10-4

Maintenance record ......................10-5

YAMAHA MOTOR

CORPORATION, U.S.A.

STREET AND ENDURO

MOTORCYCLE LIMITED

WARRANTY .............................10-7

YAMAHA EXTENDED SERVICE

(Y.E.S.) ..................................... 10-9

U1BH12E0.book Page 2 Wednesday, July 6, 2011 4:06 PM

LOCATION OF IMPORTANT LABELS

1-1

1

EAU10384

Read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of

your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label

is available from your Yamaha dealer.

1

7 6

2,3 4

5

U1BH12E0.book Page 1 Wednesday, July 6, 2011 4:06 PM

LOCATION OF IMPORTANT LABELS

1-2

1

•

2C5-F815K-00

NOTICE

5RU-21686-00

EMISSION HOSE ROUTING

THROTTLE BODY

CANISTER

ATMOSPHERE

FUEL TANK

VACUUM HOSE ROUTING

34B-21684-00

INTAKE MANIFOLD

PRESS. SENSOR

WARNING

This unit contains high pressure nitrogen gas.

Mishandling can cause explosion.

Read owner’s manual for instructions.

Do not incinerate, puncture or open.

4AA-22259-80

41

6

7 XV17ATSB(C)

2 California only

3 California only

5 XV17ATSB(C)

U1BH12E0.book Page 2 Wednesday, July 6, 2011 4:06 PM

2-1

2

SAFETY INFORMATION

EAU10289

Be a Responsible Owner

As the vehicle’s owner, you are respon-

sible for the safe and proper operation

of your motorcycle.

Motorcycles are single-track vehicles.

Their safe use and operation are de-

pendent upon the use of proper riding

techniques as well as the expertise of

the operator. Every operator should

know the following requirements before

riding this motorcycle.

He or she should:

● Obtain thorough instructions from

a competent source on all aspects

of motorcycle operation.

● Observe the warnings and mainte-

nance requirements in this Own-

er’s Manual.

● Obtain qualified training in safe

and proper riding techniques.

● Obtain professional technical ser-

vice as indicated in this Owner’s

Manual and/or when made neces-

sary by mechanical conditions.

Safe Riding

Perform the pre-operation checks each

time you use the vehicle to make sure it

is in safe operating condition. Failure to

inspect or maintain the vehicle properly

increases the possibility of an accident

or equipment damage. See page 5-1

for a list of pre-operation checks.

● This motorcycle is designed to car-

ry the operator and a passenger.

● The failure of motorists to detect

and recognize motorcycles in traf-

fic is the predominating cause of

automobile/motorcycle accidents.

Many accidents have been caused

by an automobile driver who did

not see the motorcycle. Making

yourself conspicuous appears to

be very effective in reducing the

chance of this type of accident.

Therefore:

• Wear a brightly colored jacket.

• Use extra caution when you are

approaching and passing

through intersections, since in-

tersections are the most likely

places for motorcycle accidents

to occur.

• Ride where other motorists can

see you. Avoid riding in another

motorist’s blind spot.

● Many accidents involve inexperi-

enced operators. In fact, many op-

erators who have been involved in

accidents do not even have a cur-

rent motorcycle license.

• Make sure that you are qualified

and that you only lend your mo-

torcycle to other qualified opera-

tors.

• Know your skills and limits.

Staying within your limits may

help you to avoid an accident.

• We recommend that you prac-

tice riding your motorcycle

where there is no traffic until you

have become thoroughly famil-

iar with the motorcycle and all of

its controls.

● Many accidents have been caused

by error of the motorcycle opera-

tor. A typical error made by the op-

erator is veering wide on a turn

U1BH12E0.book Page 1 Wednesday, July 6, 2011 4:06 PM

SAFETY INFORMATION

2-2

2

due to excessive speed or under-

cornering (insufficient lean angle

for the speed).

• Always obey the speed limit and

never travel faster than warrant-

ed by road and traffic conditions.

• Always signal before turning or

changing lanes. Make sure that

other motorists can see you.

● The posture of the operator and

passenger is important for proper

control.

• The operator should keep both

hands on the handlebar and

both feet on the operator foot-

rests during operation to main-

tain control of the motorcycle.

• The passenger should always

hold onto the operator, the seat

strap or grab bar, if equipped,

with both hands and keep both

feet on the passenger footrests.

Never carry a passenger unless

he or she can firmly place both

feet on the passenger footrests.

● Never ride under the influence of

alcohol or other drugs.

● This motorcycle is designed for on-

road use only. It is not suitable for

off-road use.

Protective Apparel

The majority of fatalities from motorcy-

cle accidents are the result of head in-

juries. The use of a safety helmet is the

single most critical factor in the preven-

tion or reduction of head injuries.

● Always wear an approved helmet.

● Wear a face shield or goggles.

Wind in your unprotected eyes

could contribute to an impairment

of vision that could delay seeing a

hazard.

● The use of a jacket, heavy boots,

trousers, gloves, etc., is effective in

preventing or reducing abrasions

or lacerations.

● Never wear loose-fitting clothes,

otherwise they could catch on the

control levers, footrests, or wheels

and cause injury or an accident.

● Always wear protective clothing

that covers your legs, ankles, and

feet. The engine or exhaust sys-

tem become very hot during or af-

ter operation and can cause burns.

● A passenger should also observe

the above precautions.

Avoid Carbon Monoxide Poisoning

All engine exhaust contains carbon

monoxide, a deadly gas. Breathing car-

bon monoxide can cause headaches,

dizziness, drowsiness, nausea, confu-

sion, and eventually death.

Carbon Monoxide is a colorless, odor-

less, tasteless gas which may be

present even if you do not see or smell

any engine exhaust. Deadly levels of

carbon monoxide can collect rapidly

and you can quickly be overcome and

unable to save yourself. Also, deadly

levels of carbon monoxide can linger

for hours or days in enclosed or poorly

ventilated areas. If you experience any

symptoms of carbon monoxide poison-

ing, leave the area immediately, get

fresh air, and SEEK MEDICAL TREAT-

MENT.

● Do not run engine indoors. Even if

you try to ventilate engine exhaust

with fans or open windows and

doors, carbon monoxide can rap-

idly reach dangerous levels.

U1BH12E0.book Page 2 Wednesday, July 6, 2011 4:06 PM

SAFETY INFORMATION

2-3

2

● Do not run engine in poorly venti-

lated or partially enclosed areas

such as barns, garages, or car-

ports.

● Do not run engine outdoors where

engine exhaust can be drawn into

a building through openings such

as windows and doors.

Loading

Adding accessories or cargo to your

motorcycle can adversely affect stabili-

ty and handling if the weight distribution

of the motorcycle is changed. To avoid

the possibility of an accident, use ex-

treme caution when adding cargo or

accessories to your motorcycle. Use

extra care when riding a motorcycle

that has added cargo or accessories.

Here, along with the information about

accessories below, are some general

guidelines to follow if loading cargo to

your motorcycle:

The total weight of the operator, pas-

senger, accessories and cargo must

not exceed the maximum load limit.

Operation of an overloaded vehicle

could cause an accident.

When loading within this weight limit,

keep the following in mind:

● Cargo and accessory weight

should be kept as low and close to

the motorcycle as possible. Se-

curely pack your heaviest items as

close to the center of the vehicle as

possible and make sure to distrib-

ute the weight as evenly as possi-

ble on both sides of the motorcycle

to minimize imbalance or instabili-

ty.

● Shifting weights can create a sud-

den imbalance. Make sure that ac-

cessories and cargo are securely

attached to the motorcycle before

riding. Check accessory mounts

and cargo restraints frequently.

• Properly adjust the suspension

for your load (suspension-ad-

justable models only), and

check the condition and pres-

sure of your tires.

• Never attach any large or heavy

items to the handlebar, front

fork, or front fender. These

items, including such cargo as

sleeping bags, duffel bags, or

tents, can create unstable han-

dling or a slow steering re-

sponse.

● This vehicle is not designed to

pull a trailer or to be attached to

a sidecar.

Genuine Yamaha Accessories

Choosing accessories for your vehicle

is an important decision. Genuine

Yamaha accessories, which are avail-

able only from a Yamaha dealer, have

been designed, tested, and approved

by Yamaha for use on your vehicle.

Many companies with no connection to

Yamaha manufacture parts and acces-

sories or offer other modifications for

Yamaha vehicles. Yamaha is not in a

position to test the products that these

aftermarket companies produce.

Therefore, Yamaha can neither en-

dorse nor recommend the use of ac-

cessories not sold by Yamaha or

Maximum load:

XV17ASB 191 kg (421 lb)

XV17ASBC 191 kg (421 lb)

XV17ATSB 177 kg (390 lb)

XV17ATSBC 177 kg (390 lb)

U1BH12E0.book Page 3 Wednesday, July 6, 2011 4:06 PM

SAFETY INFORMATION

2-4

2

modifications not specifically recom-

mended by Yamaha, even if sold and

installed by a Yamaha dealer.

Aftermarket Parts, Accessories, and

Modifications

While you may find aftermarket prod-

ucts similar in design and quality to

genuine Yamaha accessories, recog-

nize that some aftermarket accessories

or modifications are not suitable be-

cause of potential safety hazards to you

or others. Installing aftermarket prod-

ucts or having other modifications per-

formed to your vehicle that change any

of the vehicle’s design or operation

characteristics can put you and others

at greater risk of serious injury or death.

You are responsible for injuries related

to changes in the vehicle.

Keep the following guidelines in mind,

as well as those provided under “Load-

ing” when mounting accessories.

● Never install accessories or carry

cargo that would impair the perfor-

mance of your motorcycle. Care-

fully inspect the accessory before

using it to make sure that it does

not in any way reduce ground

clearance or cornering clearance,

limit suspension travel, steering

travel or control operation, or ob-

scure lights or reflectors.

• Accessories fitted to the handle-

bar or the front fork area can

create instability due to improper

weight distribution or aerody-

namic changes. If accessories

are added to the handlebar or

front fork area, they must be as

lightweight as possible and

should be kept to a minimum.

• Bulky or large accessories may

seriously affect the stability of

the motorcycle due to aerody-

namic effects. Wind may at-

tempt to lift the motorcycle, or

the motorcycle may become un-

stable in cross winds. These ac-

cessories may also cause

instability when passing or being

passed by large vehicles.

• Certain accessories can dis-

place the operator from his or

her normal riding position. This

improper position limits the free-

dom of movement of the opera-

tor and may limit control ability,

therefore, such accessories are

not recommended.

● Use caution when adding electri-

cal accessories. If electrical acces-

sories exceed the capacity of the

motorcycle’s electrical system, an

electric failure could result, which

could cause a dangerous loss of

lights or engine power.

Aftermarket Tires and Rims

The tires and rims that came with your

motorcycle were designed to match the

performance capabilities and to provide

the best combination of handling, brak-

ing, and comfort. Other tires, rims, siz-

es, and combinations may not be

appropriate. Refer to page 7-19 for tire

specifications and more information on

replacing your tires.

Transporting the Motorcycle

Be sure to observe following instruc-

tions before transporting the motorcy-

cle in another vehicle.

● Remove all loose items from the

motorcycle.

U1BH12E0.book Page 4 Wednesday, July 6, 2011 4:06 PM

SAFETY INFORMATION

2-5

2

● Check that the fuel cock (if

equipped) is in the “OFF” position

and that there are no fuel leaks.

● Point the front wheel straight

ahead on the trailer or in the truck

bed, and choke it in a rail to pre-

vent movement.

● Shift the transmission in gear (for

models with a manual transmis-

sion).

● Secure the motorcycle with tie-

downs or suitable straps that are

attached to solid parts of the mo-

torcycle, such as the frame or up-

per front fork triple clamp (and not,

for example, to rubber-mounted

handlebars or turn signals, or parts

that could break). Choose the lo-

cation for the straps carefully so

the straps will not rub against

painted surfaces during transport.

● The suspension should be com-

pressed somewhat by the tie-

downs, if possible, so that the mo-

torcycle will not bounce excessive-

ly during transport.

U1BH12E0.book Page 5 Wednesday, July 6, 2011 4:06 PM

DESCRIPTION

3-1

3

EAU32220

Left view

XV17ASB(C)

123

45

1. Engine oil filler cap (page 7-12)

2. Battery (page 7-30)

3. Owner’s tool kit (page 7-2)

4. Fuse box (page 7-32)

5. Shift pedal (page 4-8)

U1BH12E0.book Page 1 Wednesday, July 6, 2011 4:06 PM

DESCRIPTION

3-2

3

XV17ATSB(C)

123

45

1. Engine oil filler cap (page 7-12)

2. Battery (page 7-30)

3. Owner’s tool kit (page 7-2)

4. Fuse box (page 7-32)

5. Shift pedal (page 4-8)

U1BH12E0.book Page 2 Wednesday, July 6, 2011 4:06 PM

DESCRIPTION

3-3

3

EAU32230

Right view

XV17ASB(C)

123

456789

1. Main fuse and fuel injection system fuse (page 7-32)

2. Fuel tank (page 4-9)

3. Fuel tank cap (page 4-9)

4. Brake pedal (page 4-9)

5. Rear brake light switch (page 7-22)

6. Engine oil filter cartridge (page 7-12)

7. Air filter element (page 7-16)

8. Transfer case oil level check bolt (page 7-15)

9. Shock absorber assembly spring preload adjusting nut (page 4-16)

U1BH12E0.book Page 3 Wednesday, July 6, 2011 4:06 PM

DESCRIPTION

3-4

3

XV17ATSB(C)

123

4

56

78910

1. Main fuse and fuel injection system fuse (page 7-32)

2. Fuel tank (page 4-9)

3. Fuel tank cap (page 4-9)

4. Windshield (page 4-14/4-6)

5. Brake pedal (page 4-9)

6. Rear brake light switch (page 7-22)

7. Engine oil filter cartridge (page 7-12)

8. Air filter element (page 7-16)

9. Transfer case oil level check bolt (page 7-15)

10.Shock absorber assembly spring preload adjusting nut (page 4-16)

U1BH12E0.book Page 4 Wednesday, July 6, 2011 4:06 PM

DESCRIPTION

3-5

3

EAU32240

Controls and instruments

XV17ASB(C)

12 34 567

1. Clutch lever (page 4-8)

2. Left handlebar switches (page 4-6)

3. Multi-function meter unit (page 4-3)

4. Main switch/steering lock (page 4-1)

5. Right handlebar switches (page 4-6)

6. Throttle grip (page 7-18)

7. Brake lever (page 4-8)

U1BH12E0.book Page 5 Wednesday, July 6, 2011 4:06 PM

DESCRIPTION

3-6

3

XV17ATSB(C)

12 34 567

1. Clutch lever (page 4-8)

2. Left handlebar switches (page 4-6)

3. Multi-function meter unit (page 4-3)

4. Main switch/steering lock (page 4-1)

5. Right handlebar switches (page 4-6)

6. Throttle grip (page 7-18)

7. Brake lever (page 4-8)

U1BH12E0.book Page 6 Wednesday, July 6, 2011 4:06 PM

Page is loading ...

Yamaha 2012 Road Star S Owner's manual

Yamaha 2012 Road Star S Owner's manual

Related papers

Other documents