DYNACORD CMS1000-3 Owner's manual

Page is loading ...

CMS

3

CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Scope of Delivery, Unpacking and Inspection . . . 5

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation and Connections . . . . . . . . . . . . . . . . 5

C

ONTROLS, INDICATORS AND CONNECTIONS . . . . . . . . . . . 6

Input Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Input Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

FX 1/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

AUX 1/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

MON 1/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

MASTER with GEQ . . . . . . . . . . . . . . . . . . . . . . . . 20

DISPLAY with function keys . . . . . . . . . . . . . . . . . 23

Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

D

ISPLAY & FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Effect mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Menu mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

DIGITAL AUDIO INTERFACE . . . . . . . . . . . . . . . . . . . . 30

Installing the USB driver . . . . . . . . . . . . . . . . . . . . 30

Cubase LE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Status display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

PC-MIDI-Interface . . . . . . . . . . . . . . . . . . . . . . . . . 31

Examples of usage (Playback) . . . . . . . . . . . . . . . 32

Examples of usage (Recording) . . . . . . . . . . . . . . 32

MIDI tone generator and multi-effect unit . . . . . . 34

S

ETTING UP A STANDARD PA . . . . . . . . . . . . . . . . . . . . . . 35

Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Setting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Soundcheck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

S

ETUP EXAMPLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

CMS with D-Lite activeone . . . . . . . . . . . . . . . . . . 38

CMS with D-Lite activetwo . . . . . . . . . . . . . . . . . . 39

CMS with D-Lite activefour . . . . . . . . . . . . . . . . . . 40

CMS with Xa-2 system . . . . . . . . . . . . . . . . . . . . . 41

CMS with CORUS-Evolution system . . . . . . . . . . . 42

CMS mit VariLine System . . . . . . . . . . . . . . . . . . . 43

S

PECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

INHALT

EINFÜHRUNG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Lieferumfang, Auspacken und Überprüfen . . . . . . 45

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Aufstellen und Anschließen . . . . . . . . . . . . . . . . . 45

B

EDIENELEMENTE UND ANSCHLÜSSE . . . . . . . . . . . . . . . . . 46

Input Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Input Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

FX 1/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

AUX 1/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

MON 1/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

MASTER mit GEQ . . . . . . . . . . . . . . . . . . . . . . . . . 60

DISPLAY mit Funktions-Tasten . . . . . . . . . . . . . . . 63

Rückseite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

D

ISPLAY & FUNKTIONEN . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Effekt-Betriebsart . . . . . . . . . . . . . . . . . . . . . . . . . 66

Menü-Betriebsart . . . . . . . . . . . . . . . . . . . . . . . . . 66

Effekte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

DIGITAL AUDIO INTERFACE . . . . . . . . . . . . . . . . . . . . 71

Installation des USB-Treibers . . . . . . . . . . . . . . . . 71

Cubase LE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Funktionsanzeige im Display . . . . . . . . . . . . . . . . 72

PC-MIDI-Interface . . . . . . . . . . . . . . . . . . . . . . . . . 72

Anwendungsbeispiele (Wiedergabe) . . . . . . . . . . 73

Anwendungsbeispiele (Aufnahme) . . . . . . . . . . . . 74

MIDI-Klangerzeuger und Multieffektgerät . . . . . . . 75

A

UFBAU EINER STANDARD-PA . . . . . . . . . . . . . . . . . . . . . 76

Verkabelung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Aufbau . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Soundcheck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

A

UFBAUBEISPIELE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

CMS mit D-Lite activeone . . . . . . . . . . . . . . . . . . . 79

CMS mit D-Lite activetwo . . . . . . . . . . . . . . . . . . . 80

CMS mit D-Lite activefour . . . . . . . . . . . . . . . . . . 81

CMS mit Xa-2 System . . . . . . . . . . . . . . . . . . . . . . 82

CMS mit CORUS-Evolution System . . . . . . . . . . . 83

CMS mit VariLine System . . . . . . . . . . . . . . . . . . . 84

S

PECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

CMS

3

4

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not cover any ventilation openings. Install in accordance with the manufacture’s instructions.

8. Do not install near heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or the grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the third prong are provided for your safety. I the provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving

the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for a long period of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or orbjects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate

normally, or has been dropped.

15. Do not expose this equipment to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the equipment.

16. To completely disconnect this equipment from the AC Mains, disconnect the power supply cord plug from the AC receptacle.

17. The mains plug of the power supply cord shall remain readily operable.

18. No naked flame sources, such as lighted candles, should be placed on the apparatus.

19. The product should be connected to a mains socket outlet with a protective earthing connection.

IMPORTANT SERVICE INSTRUCTIONS

CAUTION: These servicing instructions are for use by qualified personnel only. To reduce the risk of electric shock, do not

perform any servicing other than that contained in the Operating Instructions unless you are qualified to do so. Refer

all servicing to qualified service personnel.

1. Security regulations as stated in the EN 60065 (VDE 0860 / IEC 65) and the CSA E65 - 94 have to be obeyed when servicing the appliance.

2. Use of a mains separator transformer is mandatory during maintenance while the appliance is opened, needs to be operated and is connected to the mains.

3. Switch off the power before retrofitting any extensions, changing the mains voltage or the output voltage.

4. The minimum distance between parts carrying mains voltage and any accessible metal piece (metal enclosure), respectively between the mains poles has to be 3 mm and

needs to be minded at all times. The minimum distance between parts carrying mains voltage and any switches or breakers that are not connected to the mains

(secondary parts) has to be 6 mm and needs to be minded at all times.

5. Replacing special components that are marked in the circuit diagram using the security symbol (Note) is only permissible when using original parts.

6. Altering the circuitry without prior consent or advice is not legitimate.

7. Any work security regulations that are applicable at the locations where the appliance is being serviced have to be strictly obeyed. This applies also to any regulations

about the work place itself.

8.

All instructions concerning the handling of MOS-circuits have to be observed.

WEEE RECYCLING/DISPOSAL INSTRUCTIONS

The Wheelie Bin symbol found on the product or in the manual indicates that this product must not be disposed of with other waste. It is in our category the

manufacturer’s responsibility to properly dispose of their waste electrical and electronic equipment (WEEE) at the end of its life. Due to the differences in each EU

country’s management of WEEE, please contact your local distributor. We are committed to facilitate our own electronic-waste-management-system, for the free

of charge return of all EVI Audio GmbH products: Telex, DYNACORD, Electro-Voice and RTS. Arrangements are made with the dealer where you purchased the

equipment from, for the returning of all unusable equipment at no cost, to the factory in Straubing, for environmental protective disposal.

The lightning flash with arrowhead symbol, within an equilateral

triangle is intended to alert the user to the presence of uninsulated

„dangerous voltage“ within the product’s enclosure that may be of

sufficent magnitude to constitute a risk of electric shock to per-

sons.

The exclamation point within an equilateral triangle is intended to

alert the user to the presence of important operating and

maintance (servicing) instructions in the literature accompanying

the appliance.

NOTE: SAFETY COMPONENT (MUST BE REPLACED BY ORIGINAL PART)

CMS

3

5

1 Introduction

Because of their comprehensive set of integrated fea-

tures – like equalizer and effects units – the Compact

Mixing Systems CMS 1000-3, CMS 1600-3 and

CMS 2200-3 are professional mixers offering an opti-

mized all-in-one solution for basically any application. DY-

NACORD CMS consoles are quickly set up. Complicated

rack configuration and interference-prone wiring of sev-

eral single components cease to apply.

The mixer’s ergonomic console shape and clearly structu-

red controls provide perfect overview for instant access

at all times. Also during the transport you will quickly

learn to appreciate the CMS’s superiority: recessed hand-

les on the sides, compact dimensions and low weight,

plus the sturdy cover (optional) that protects the cont-

rols from being damaged. However, if you would rather

like to install your CMS 1000-3 in a 19” rack shelf, no pro-

blem. The only thing you have to do is to replace the

plastic side panels by a pair of metal rack mount ears.

Through its multiple functions, its high dynamic capacity,

and extremely low-noise design in combination with its

24-bit Dual-Stereo effect unit and the DIGITAL AUDIO IN-

TERFACE, the CMS is best equipped for universal use.

1.1 Scope of Delivery, Unpacking and

Inspection

Open the packaging and take out the CMS. Remove the

FX unit display‘s protective foil. Inspect the CMS‘s enclo-

sure for damages that might have occured during trans-

portation. Each CMS is examined and tested in detail

before leaving the manufacturing site to ensure that it ar-

rives in perfect condition at your place. Please inform the

transport company immediately if the CMS shows any

damage. Being the addressee, you are the only person

who can claim damages in transit. Keep the cardboard

box and all packaging materials for inspection by the

transport company. Keeping the cardboard box including

all packing materials is also recommended, if the CMS

shows no external damages.

CAUTION: Do not ship the CMS in any other than its

original packaging.

Packing the CMS like it was packed by the manufacturer

guarantees optimum protection from transport damage.

1.2 Warranty

Keep the original invoice that states the purchase/deliv-

ery date together with the warranty certificate at a safe

place. The manufacturer‘s warranty covers all substantial

defects in materials and workmanship for a period of 36

months from the date of purchase. Liability claims are ac-

cepted solely, when a valid - correctly and completely

filled out - Warranty Registration Form is presented by

the original owner of the product. The warranty does not

cover damage that results from improper or inadequate

treatment or maintenance. In case of alteration or unau-

thorized repairs, the warranty is automatically terminat-

ed.

1.3 Installation and Connections

Do not cover the ventilation louvers in the bottom plate

of the appliance. Always place the CMS on an even sur-

face to allow for sufficient airflow during the operation.

Before establishing the mains supply connection, please

make sure that the device matches the voltage and fre-

quency of your local mains supply. Check the label next

to the mains switch.

HINT: Using original Neutrik connectors is recom-

mended for optimal audio quality.

•1 CMS

• 1 Owner‘s Manual (this document)

•1 Quickstart Manual

• 1 Mains Cord (2 meters)

• 1 Warranty Certificate including Safety Instructions

• 1 DVD with USB driver, documentation, software,...

CMS

3

6

2 Controls, Indicators and

Connections

2.1 Input Mono

HINT: When connecting signal sources, please make sure to set the corresponding channel faders

or at least the master faders to their minimum positions or engage the STANDBY switch.

This will save you, your audience, and the equipment from extensive wear from unpleasant

pops.

1 - MIC

Electronically balanced XLR-type inputs for the connection of low impedance microphones like the

ones featured in major studio and live mixing consoles. This type of input stage provides extraordinary

low noise signal conversion at an extremely low distortion rate (typical < 0.002%) even in the high fre-

quency range. Generally, any type of microphone can be connected as long as its pin assignment is in

accordance to the diagram shown below. When condenser microphones are connected, you have to

press the PHANTOM POWER button, which is located in the input section. The microphone gets its

operating voltage (+48 V DC) through the mixer. PHANTOM POWER can be activated in groups of 6

MIC inputs

The MIC input accepts levels between -60 dBu and +21 dBu – depending on the setting of the corre-

sponding gain control. Because of the low impedance and the switchable PHANTOM POWER the XLR

input is preferred for MIC applications. Because of the high input acceptance of up to 21 dBu the XLR

input is also suited to connect further mixers, effect units, keyboards etc. But because of the higher

level and impedance matching the LINE input should be preferred.

2 - LINE

Electronically balanced inputs for the connection of electronic instruments, such as keyboards, drum

machines, E-guitars and E-basses with an active output, as well as all other high level signal sources,

like additional mixers, FX units, CD players, etc. The LINE input accepts levels between -40 dBu and

+41 dBu. The connection of balanced or unbalanced signal sources is established through monaural

or stereo phone plugs, assigned according to the diagram below. If the device that you want to connect

has a balanced output stage, the use of balanced cables with stereo phone plugs is preferable. This

type of connection is greatly insensitive to the induction of external noise or HF interference.

Do not connect identical signal sources to LINE and MIC inputs at the same time, since the signals

would interfere with each other, resulting in level reduction.

Illustration 2-1: Microphon input

Illustration 2-2: Unbalanced or balanced assignment of line input

UNBALANCED

SHIELD

HOT

BALANCED

SHIELD COLD

HOT

CMS

3

7

HINT: Please, do not connect E-guitars or E-basses with passive, high impedance outputs directly to a LINE input.

The LINE inputs of the CMS – like the Line level inputs of mixers from other manufacturers – are designed

for the connection of the relatively low source impedance of electronic instruments. The reproduction of the

instrument’s original sound characteristics will be unsatisfactory. Connect those instruments using a special

transformer or pre-amplifier with very high input impedance. Musical instruments with an active electronic

output (battery-powered) can be connected without any problems.

3 - INSERT

Stereo phone jack with breaker function. The low impedance output is assigned to the tip (send) and the high imped-

ance input (return) is assigned to the ring. This jack allows the connection of external compressors, limiters, EQs, de-

noisers, etc. into the corresponding channel’s signal path. The insertion point is post gain controls, Lo-Cut filters, and

voicing stage and pre sound shaping section and channel faders. You have to use a stereo phone plug – according to

the diagram aside – in case you intend to use this jack as a true insert bus.

Using as DIRECT OUT

When using the insert socket as a DIRECT OUT (Pre EQ), the stereo phone plug’s tip and ring have to be short circuited,

so that the audio signal is not interrupted. If you are using a monaural phone plug instead, you will get a DIRECT OUT

with breaker function – the signal flow within the channel is interrupted.

4 - GAIN

CONTROL

Rotary control for adjusting a MIC/LINE input’s sensitivity. These controls let you optimally adjust the incoming signals

to the mixer’s internal operation level. Cautious adjusting offers the benefits of an improved S/N-ratio and provides you

with the full bandwidth of the CMS’s outstanding sound capabilities. On the XLR-type connectors an amplification of

0 dB is achieved when the control is set all the way to the left and +60 dB when the control is set all the way to the right.

Especially when dealing with very low input levels – during vocal recordings and when the speaker is located in a dis-

tance – the high gain is extremely profitable. Using the LINE input, the signal is generally attenuated by -20 dB while

maintaining the total adjustment range of 60 dB. The LINE input’s unity gain – no amplification (0 dB) – is achieved at

the 20 dB mark. The following is meant as a short note for your assistance on how to determine the right input level:

GAIN setting instructions:

1. Set the gain control and the corresponding channel fader to their minimum values.

2. Connect the desired sound source (microphone, musical instrument, etc.) to the desired MIC or LINE input.

3. Start the reproduction of the sound source at the highest volume level to be expected – respectively sing or speak

as loud as possible directly (short distance) into the microphone.

4. While playing the sound source or singing into the microphone, adjust the input level using the gain control, so

that during the loudest passages the PK LED is just not lit, but the SIG present LED lights constantly. This is the

basic channel setting, leaving you with at least 6 dB of headroom, i.e. you have at least a range of 6 dB before sig-

nal clipping occurs. In case you intend to make further adjustments to the channel’s EQ setting, you should per-

form steps 3. and 4. again afterwards, since changes in the sound shaping section also have an influence on the

channel’s overall level.

Illustration 2-3: Y cable for Insert jack

Illustration 2-4: Direct Out cable without signal interruption

-

+

hot

shield

DIRECT OUT

CMS

3

8

5 - LO CUT 80 HZ

When the LO CUT switch is engaged, frequencies below 80 Hz are attenuated (18 dB octave slope). In

most cases using the LO CUT filter with microphone channels is a good advice, since it efficiently

suppresses popping sounds, rumbling noise and low-frequency feedback. The only exceptions are

kick drum and acoustic bass. Sometimes it can be also very effective to combine the LO CUT filter with

the voicing filter. For instance to provide vocals with more “body”, without getting additional low

pitched noise. Activating the LO CUT and raising the bass level (LO EQ) provides you with a richer

sound, without additional rumbling or popping noise. Another welcome side effect is, that the power

amplifier and the connected loudspeakers do not get “polluted” with unnecessary low-pitched inter-

ference. Your audience will be thankful for the use of the LO CUT filter, too, since in this way they can

enjoy a truly clear, natural, and powerful sound performance.

6 - VOICE FILTER

This button activates an asymmetric microphone filter, which can be used in addition to the channel

EQ. The voicing filter enhances the first harmonic oscillation and the treble of the human voice while

slightly attenuating the mid frequency range. This voice shaping method provides powerful vocals that

are clearly emphasized from the rest of the mix. This “pre-shaping” is not achievable using ordinary

third or octave band equalizers. The use of this filter is not restricted to vocals only. Horns, wood-

winds, and other acoustic instruments can profit from the voicing filter as well. We leave it entirely up

to your creativity and imagination to try the VOICE filter with as many different sound sources, as you

want. Normally, you do not have to fear any problems with the occurrence of feedback.

Illustration 2-5: LO CUT filter

Illustration 2-6: Voice filter

CMS

3

9

7 - EQ SECTION

The mixer’s EQ section allows very differentiated shaping of the incoming audio signal within miscellaneous frequency

bands. Turning one of the EQ level controls to the right enhances/amplifies the corresponding frequency range while

turning it to the left lowers/attenuates the signal of that specific frequency band. Before you begin to alter the sound,

all EQ controls should be set to their neutral position, i.e. their marker points straight up (locked in place). Try not to

set the EQ controls to extreme positions. Usually, minor changes are totally sufficient and produce the best results in

the overall sound. You should use the natural reproduction as an orientation mark and rely on your musically trained ear.

The moderate use of the MID control is the best remedy to avoid acoustical feedback. Especially in this frequency range

you should try to avoid excessive enhancement. Lowering the level more or less in this band will provide you with high

amplification rates without feedback. Use the LO control according to your pleasing, to add more “punch” to the sound

of a kick drum or “body” to the vocals. Use the HI control in the same way to provide cymbals and the human voice with

more treble and a more transparent sound. The MID EQ section offers parametric EQ-setting via separate rotary controls

for the adjustment of level (MID) and frequency band (kHz) in the range between 100 Hz and 8 kHz.

Adjustments in the MID frequency range are certainly the most effective way to shape the sound. As a matter of fact,

determining the correct center frequency is not always as easy as it seems. Here is one method – amongst others – how

to quickly find the right setting of the parametric EQ for your application:

MID filter setting instructions:

1. Slightly lower the channel fader to avoid feedback.

2. Turn the MID rotary control to 9 dB up to 15 dB.

Illustration 2-7: LO/HI filters

Illustration 2-8: MID filter

CMS

3

10

3. Play the desired sound source or talk into the microphone.

4. While doing so turn the frequency rotary control (kHz) slowly from left to right.

5. Surely and within no time, you will detect the frequency range that is not to your liking or caus-

ing the feedback.

6. Leave the frequency control in this position and turn the MID control to the left until the sound

is natural or to your liking.

8 - FX 1/2

The FX controls allow adjusting individual amounts of the input signals to be routed to the integrated

FX 1 or the FX 2 effects units. The signal path is split post volume fader – post fader – so that the fader

setting also influences the amount of the signal that is fed to the FX units. Using the FX controls lets

you easily assign an effect for groups of musical instruments or vocals. For example, you can assign a

short reverb effect of the FX 1 unit to the lead vocals and a combined effects program – echo, hall,

and chorus – via FX 2 to the background vocals. To determine the desired intensity of each effect, you

should start with the controls set at their center and make individual adjustments from there on.

Please monitor the PK LEDs in the FX 1/2 channels. The indicator should only light briefly at the oc-

currence of high program peaks. If the indicator is constantly lit, you should lower the send levels of

those channels where the program peaks occur. For further information, please read the paragraphs

about the FX 1/2 units. In case you are not using the internal FX units and/or you want to connect ex-

ternal signal processing units, the pre-mixed FX 1/2 signals are outputted via the FX 1/2 SENDS jacks.

9 - AUX 1/2

AUX 1 and AUX 2 controls are primarily meant for establishing two independent monitor mixes. Using

the master section’s AUX PRE/POST switches allows determining whether the signals are split pre or

post fader.

PRE-FADER

The audio signal that is present at the AUX control is tapped pre volume fader and therefore not af-

fected by the fader’s setting. This mode is mainly used for monitoring. Pre-Fader Monitoring is espe-

cially preferable when monitoring and master mix need to be completely different from each other,

e.g. when the volume setting of particular musical instruments or vocals needs to be higher or lower

than in the master mix. In most cases the mixing console is placed somewhere in the audience area

(FOH) and is being operated by an sound technician.

POST-FADER

The audio signal that is present at the AUX control is tapped post volume fader and therefore affected

by the fader’s setting. This mode is mainly used for establishing FX- or special monitoring mixes. Using

the POST-Fader method is recommended when the mixer is also located on the stage and you have to

operate it yourself. Setting all AUX 1 or AUX 2 controls to their center position, the master mix is also

present on the monitor bus, giving you the opportunity to control the volume settings of each channel

individually from the stage. The overall volume of the monitor mix is set using the AUX 1/2 faders in

the master section. If you are using this option you should keep in mind that all volume changes made

with the channel faders also apply to the monitor mix, leaving you with a higher risk of acoustic feed-

back. The Post-Fader Monitoring method provides the possibility of canceling channels of some instru-

ments – like kick or snare drum, which are in fact already very loud on-stage – from the monitor mix

by turning the corresponding controls all the way to the left.

10 - MON 1/2

MON 1 and MON 2 controls are primarily meant for establishing two independent monitor mixes. The

signal routing is always PRE FADER.

11 - PAN

This control determines the position of the connected sound source within the stereo image. When

this control is set at its center position, the audio signal is fed with equal levels to the L and R master

busses. The PAN control section is designed to maintain the essential sound pressure level, no matter

at what position within the stereo image the PAN control is set to.

12 - MUTE

The MUTE button mutes the input signal post fader, including all FX/AUX/MON sends. PFL and Signal/

Peak stay functional.

CMS

3

11

HINT: Use the MUTE button for muting temporarily not used input channels without changing the settings of the

FX/AUX/MON controls and the channel fader.

13 - PFL

Engaging the PFL button routes the audio signal to the headphones bus, so that it is present at the phones output con-

nector. The meter instrument in the master section is simultaneously switched, so that the left LED-chain indicates the

level of the actually chosen channel (in dBu), which allows optimally matching the level of the signal source. The phones

output volume does not dependent on the setting of the corresponding channel fader (Pre Fader Listen), which provides

the possibility to listen to or shape the sound of the selected audio signal, without need to include it in the master mix.

14 - SIG / PK I

NDICATOR

The signal-peak indicator plays a key role when setting input levels. Unlike the mixers of many other manufacturers that

either only provide a peak indicator or no channel indicator at all, the PK (peak) LED of the CMS provides optical indi-

cation of the risk of occurring overdrive before you would actually hear the distortion over the connected speaker sys-

tems. As outlined in the setting instructions, the Signal-LED should blink in the rhythm of the incoming signal. If this is

not the case, you have to increase the gain. If the PK LED, on the other hand, blinks frequently or lights continuously,

the corresponding channel is likely to enter clipping and you have to turn the gain control a bit to the left. The Signal-

LED lights at levels -30 dB below clipping while the peak LED lights at a level of -6 dB below the occurrence of overdrive.

Keeping an eye on the indicator during a performance is also a good idea, because some very dynamically performing

members of a band or changing keyboard setups can easily lead to channel clipping, resulting in the degradation of the

overall sound.

15 - F

ADER

The channel faders set the volume of the corresponding channels, establishing an accurately proportioned mix. The

channel faders should be positioned within the range of -5 dB to 0 dB, leaving you with a degree of control that allows

the precise matching of relative big differences in the channels’ level settings. The overall volume is set through the use

of the master faders. Even though the channel faders offer an additional amplification of +10 dB, we would like to advise

you to exceed the +5 dB mark only in very few exceptional cases. If the CMS’s summing bus gets “overloaded” with too

many “high level” input channels, despite its special gain structure, the summing amplifier could be driven into clipping.

Once you register, that some channel faders are set above the 0 dB marking, lowering the setting of each channel fader

by about -5 dB and increasing the overall output level by elevating the master faders is the wiser solution. The proportion

of the mix and the overall volume stay the same while the risk of clipping is banished.

CMS

3

12

2.2 Input Stereo

Since most features – AUX faders, controls and channel faders – of the STEREO INPUTS are virtually

identical to the ones of the MONO INPUTS we will not discuss their functioning in detail again. Thus,

in the following we only point out the differences and like to ask you to refer to the analogous para-

graphs within this owner’s manual describing the MONO INPUTS.

16 - MIC

Different from the products of many other manufacturers, the stereo input channels of the CMS, like

their monaural counterparts, incorporate extensive circuitry and electronically balanced XLR-type con-

nectors for the connection of low impedance microphones. No matter if your setup is more micro-

phone-oriented or you have more line level sound sources to connect, you can always use the full

amount of input channels, provided by your CMS. Dependable on its setting, the high-quality MIC input

in the stereo channel is capable of handling levels between -60 dBu and +11 dBu. Low-level circuitry

architecture and phantom power (+48 V) ability of this XLR-type input are mainly aimed at the connec-

tion of microphones, making it not necessarily suitable for connecting Line level appliances, like mix-

ers, effects units, etc. Please use the provided LINE inputs to connect those sound sources. General

functions and usage of MIC inputs were already discussed in detail for monaural channels.

17 - STEREO INPUT L/MONO R

Electronically balanced inputs for the connection of musical instruments with stereo output, like key-

boards, drum machines, E-guitars and E-basses with an active output as well as all other equivalent

sound sources with high level outputs, like additional mixing consoles, FX units, CD players, etc. The

stereo LINE input is meant for balanced or unbalanced sound sources with levels between -20 dBu and

+30 dBu.

Using phone plugs

For the connection of external devices you can use monaural or stereo phone plugs, which are in ac-

cordance to the diagram below. If the external appliance is equipped with a balanced output stage,

using balanced cables and plugs is preferable, since this type of connection provides improved shield-

ing against HF induction and external noise.

In case you want to connect a monaural sound source to a stereo input channel, you just have to plug

it into the L/MONO input. The signal gets internally routed to both channels.

Illustration 2-9: Microphone input (Stereo) of CMS 1000

Illustration 2-10: Pin assignment of XLR microphone input

CMS

3

13

Using RCA plugs

The RCA inputs CD 1-2 and CD 3-4 are connected in parallel to the phone inputs. Do not connect signal sources to phone

and RCA inputs at the same time.

Using the DIGITAL AUDIO INTERFACE (USB)

When using the DIGITAL AUDIO INTERFACE two stereo signals are available at USB 1-2 or USB 3-4. Do not connect signal

sources to phone inputs when using the DIGITAL AUDIO INTERFACE for playback. See page 19 for more details about

the DIGITAL AUDIO INTERFACE.

18 - GAIN MIC

Rotary controls for adjusting the MIC inputs’ sensitivity, providing the possibility to optimally match the incoming signals

with the mixer’s internal operation level. The GAIN MIC control in the stereo channel is only active for the XLR-type input.

For further information about setting and functioning of these controls, please refer to the chapter “GAIN” of the MONO

INPUT description within this manual.

CAUTION: The GAIN MIC control of an inactive microphone input should always be set to its minimum position.

Otherwise the noise of the inactive input is added to the audio signal of the corresponding LINE input,

which could lead to unnecessary extra noise at the master output, becoming clearly intelligible in pro-

gram breaks.

19 - GAIN LINE CD / USB

These rotary controls are for matching the incoming line level signals to the operating level of the CMS. The total adjust-

ment range is 30 dB. Unity gain – no amplification (0 dB) – is achieved at the 0 dB mark. The control offers level reduc-

tion of -10 dB and an amplification of +20 dB. This range allows the connection of most professional, semi professional,

and hi-fi sound sources. For further details on how to set the LINE TRIM control, please refer to the description

of the GAIN control in monaural channels.

Illustration 2-11: Unbalanced or balanced assignment of phone plus

Illustration 2-12: RCA inputs CD 1-2 and 3-4

Input CMS 1000 CMS 1600 CMS 2200

CD 1-2 Stereo 7-8 Stereo 13-14

CD 3-4 Stereo 9-10 Stereo 15-16

Table 2-13: Assignment of CD 1-2 or CD 3-4 inputs to CMS input channels

Illustration 2-14: DIGITAL AUDIO INTERFACE

Input CMS 1000 CMS 1600 CMS 2200

USB 1-2 Stereo 11-12 Stereo 17-18

USB 3-4 Stereo 13-14 Stereo 19-20

Table 2-15: Assignment of USB 1-2 or USB 3-4 inputs to CMS input channels

UNBALANCED

SHIELD

HOT

BALANCED

SHIELD COLD

HOT

CMS

3

14

HINT: If you use a keyboard as sound source on one of the stereo inputs, make sure that no split

zones or layers with channel separation are activated. The stereo channel mapping will oth-

erwise appear like it is set on the keyboard – the lower layer in the left and the top layer in

the right channel – and you will not have the opportunity to re-position the sound in the

overall stereo image, unless you connect the keyboard output to two adjacent monaural

input channels, leaving you the option to place the sound in the final mix via PAN controls.

One more tip, in case you desperately need another input and all channels of the CMS are already in

use: The microphone input and the phone plug-type inputs are electrically totally separated from each

other. Each input is equipped with its own GAIN MIC or GAIN LINE CD/USB control – respectively trim

control, providing you with the possibility to connect a LINE level sound source in addition to a micro-

phone. Of course, the two sources share all other controls. Consequently, separate adjustments are

not possible. Hence to that fact, this option is only meant as a subsidiary function and should only be

used when there is absolutely no other alternative.

20 - EQ SECTION

The mixer’s EQ section allows very comprehensive and effective shaping of the incoming audio signal

within miscellaneous frequency bands. Turning one of the EQ level controls to the right enhances/am-

plifies the corresponding frequency range while turning them to the left lowers/attenuates the signal

of that specific frequency band. Before you begin to alter the sound, all EQ controls should be set to

their neutral position, i.e. their marker points straight up (locked in place). Do not set the EQ controls

to extreme positions. Usually, minor changes are totally sufficient and produce the best results in the

overall sound. You should use the natural reproduction as an orientation mark and rely on your musi-

cally trained ear. The moderate use of the MID control is the best remedy to avoid acoustical feedback.

Especially in this frequency range you should try to avoid excessive enhancement. Lowering the level

more or less in this band will provide you with high amplification rates without feedback.

The EQ section of the STEREO channels is designed in a way that HI and LO controls provide a degree

of control that is equally adequate for LINE level inputs and microphones. The MID control is active in

a comparably wide frequency band around 2.4 kHz. With most microphones this is the critical range,

where a slight attenuation offers excellent results.

21 - FX 1/2

These controls determine the amount of the summed L and R signal that is sent POST-FADER to the

FX 1 or FX 2 summing bus. For more details on the functioning of these controls, please refer to the

Input Mono section of this owner’s manual.

22 - AUX 1/2

These controls determine the amount of the summed L and R signal that is sent to the AUX 1 or AUX 2

summing bus. Depending on the setting of the AUX PRE/POST switch in the CMS’s master section you

can choose if the signal gets split pre or post fader. For more details on the functioning of these con-

trols, please refer to the Input Mono section of this owner’s manual.

Illustration 2-16: HI, MID and LO filters

CMS

3

15

23 - MON 1/2

These controls determine the amount of the summed L and R signal that is sent to the MON 1 or MON 2 summing bus.

The signal gets always split pre fader. For more details on the functioning of these controls, please refer to the Input

Mono section of this owner’s manual.

24 - BAL

The function of the BAL control of the stereo channels is equivalent to the PAN control’s function of the monaural chan-

nels. If you turn the rotary control all the way to the right, the right signal is outputted to the right output while the signal

of the left channel is muted. When the control is set to its center position, the L/R signals are present with their equal

intensity on the corresponding outputs. Whenever stereo sound sources are connected to a stereo input, you should

leave the BAL control at the center position or make only minor adjustments in either direction. In case a microphone

or another monaural sound source is connected, the BAL controls function absolutely identical to the PAN controls of

the monaural input section.

25 - MUTE

The MUTE button mutes the input signal post fader, including all FX/AUX/MON sends. PFL and Signal/Peak stay opera-

tional.

HINT: Use the MUTE button for muting temporarily not used input channels without changing the settings of the

FX/AUX/MON controls and the channel fader.

26 - PFL

Engaging the PFL button sums the stereophonic audio signal of the corresponding input channel and routes the result-

ing monaural signal to the headphones bus. You are able to listen to the audio signal via the PHONES output. The meter

instrument in the master section is simultaneously switched, so that the left LED-chain indicates the level of the actually

chosen channel (in dBu), which allows optimally matching the level of the signal source.

You can assign as many channels as you want to the phones summing bus at the same time. The volume levels of the

individual signals are not affected by the setting of the corresponding channel faders (Pre Fader Listen). This gives you

the opportunity to set the level and the EQ of a channel, without the need to include it in the master mix, i.e. you can

leave the channel fader down or even engage the MUTE button.

27 - SIG/PK

The stereo SIG/PK indicator function provides independent analysis of left and right channel audio signals. The respec-

tive highest level reading is indicated, assuring that neither one is already driven into clipping. For further information

on how to use this indicator most efficiently, please refer to the description of the monaural channel’s identical feature.

28 - F

ADER

The channel fader is used to simultaneously adjust both levels (volumes) of the stereo signal. Functioning and specifi-

cations are totally similar to the monaural channel fader, as previously described under INPUT/MONO.

CMS

3

16

2.3 FX 1/2

The CMS offers two independently controllable, identically configured 24-bit stereo effect units – FX 1

and FX 2. Each unit provides 100 program presets, which are selected by the use of the UP/DOWN

buttons. Parameters of presets can be edited and stored as User Preset (101 - 120), see page 26 for

details. The 100 presets are divided into groups according to their different effect structure, as shown

on a printed listing. The programs within each preset group are sorted in ascending order, where high-

er numbers provide the same FX type with increased intensity. Presets 1 - 20 offer high quality rever-

beration effect programs that are equally suitable for live performance, recording studio or home

recording applications. Program numbers 21 - 40 provide mixed effect types of echo+reverb and cho-

rus while the numbers 41 - 60 offer different delay effects. The last group from 61 - 100 provides dif-

ferent doubling effects presets as well as special delay and reverb programs. During the initialization

of the FX units (when switching on the power of the CMS), preset 05 (BRIGHT HALL, Large Hall 3) is

selected for the FX 1 while the FX 2 unit is set to preset 55 (MONO DELAY, 230 ms 40%). These two

effects are similarly suitable for live performances and recording applications. This is the factory-pre-

set configuration that can be changed any time.

The buttons below the display are used in menu mode also, please see page 23 for details.

S

ELECTING A PRESET

To select a preset, pleace proceed as follows:

1. Below the display there are two buttons for each effect unit.

2. Use the DOWN button (left) of an effect unit to decrease the number of the active preset. Use

the UP button (right) of an effect unit to increase the number of the active preset.

3. Keeping a button pressed continuously lets you step quickly through the program numbers.

4. Press the UP and DOWN button simultaneously to select the first preset of the next effect group.

The two effect programs are equally suitable for live performance or recording applications and can

be used separately or together. For testing, evaluating and selecting effect programs, please also refer

to the preset table on page 29, which provides detailed description of all effect presets. This listing

contains all preset names together with the corresponding effect structure, field of application, and

frequency characteristics. Take your time to test all presets and select the ones that are best suited

for your specific application.

29 - FX ON/OFF

Phone jack for the connection of an optionally available DYNACORD FS 11 (DC-FS11) footswitch to

switch the effect mode of the internal FX units on or off. To accomplish this function, the FX 1 and

FX 2 ON switches have to be engaged.

HINT: The function of the footswitch can be edited via the Footswitch Ctrl. entry in the FX Con-

trol Setup dialog, see page 27 for details.

30 - FX 1/2 SENDS

SOCKET

The audio signal of the mix that you have established for the corresponding FX bus – the identical mix

that is fed to the internal FX 1/2 units – is present at this socket, which makes it perfect for connecting

external FX units, for example. The external devices output signals can be sent back to the CMS via

stereo channel input.

31 - FX 1/2 SEND

CONTROL

Setting the level at the FX 1/2 SENDS sockets is possible by means of the corresponding FX SEND con-

trol.

Illustration 2-17: Effect mode

BRIGHT HALL MONO DELAY

REC STUDIO MIDI PEAK AUX 1

5 55

Large Hall 3 230 ms 40%

FX1 FX2

CMS

3

17

32 - FX 1/2 TO AUX 1/2

These controls allow adding the output signal (pre fader) of FX 1 or FX 2 to the AUX 1 or AUX 2 channel.

33 - FX 1/2

TO MON 1/2

These controls allow adding the output signal (pre fader) of FX 1 or FX 2 to the MON 1 or MON 2 channel. Experience

has revealed that the effect level in the monitor mix has to be lower than the level in the master mix, since the distance

between monitor speakers and artists is much shorter.

34 - PK LED

These indicators signal if the internal FX units or the FX 1/2 SENDS signals are on the verge of clipping. To achieve an

adequate S/N ratio, please adjust the FX units input level as follows:

FX input level setting instructions:

1. Establish a “dry” mix – without effect settings – according to the previous descriptions.

2. Position the effect return fader of the corresponding effect channel at the -5 dB mark.

3. Use the UP/DOWN buttons to select the desired FX program preset.

4. Press the FX ON switch.

5. Play (start the reproduction of) the sound source connected to the desired input channel and adjust the desired

amount of the FX signal, using the FX controls of this input channel. Repeat this step for all input channels that

you want to include in your effect mix.

6. Monitor the Peak LED so that it only lights frequently at highly dynamic signal peaks. When clipping occurs,

reduce the FX controls in the channels.

7. Use the FX to AUX or FX to MON control to add the effect mix to the AUX or monitor mix. Use the Effekt Return fad-

ers to add the desired amount of the FX signal to the master mix.

In case you are using a different effect setting for the second FX unit, you have to repeat steps 2 - 7, respectively. Pay

some attention to the peak indicators when operating your CMS to be able to quickly interact when the signal levels

exceed the normal range and enter clipping.

35 - FX ON

This switch switches an internal FX unit on and the green LED lights. Please keep in mind that you can also use an ex-

ternal footswitch or a connected MIDI device for the switching of the FX unit. In this case, the LED also shows the actual

operational status of the FX unit. If you want to use a footswitch (or MIDI device), the FX ON switch has to be engaged

first. The corresponding FX unit is activated and you can use the footswitch (or MIDI device) to switch the selected ef-

fect program on or off.

36 - PFL

Engaging the PFL button routes the audio signal to the headphones bus, so that it is present at the phones output con-

nector. The phones output volume is independent of the corresponding channel fader’s setting (Pre Fader Listen),

which provides the possibility to listen to the sound of the selected audio signal, without including it in the master mix.

37 - E

FFEKT RETURN FADER

These stereo faders are used to determine the effect amount added to the master mix. In case you have to set these

faders at a position above the +5 dB mark, please check if the FX unit’s input signals are adjusted properly. Otherwise

use the FX SEND controls to increase the input levels.

CMS

3

18

2.4 AUX 1/2

Generally, the AUX 1/2 channel is used for the connection of an additional, external FX unit. De-

pending on the setting of the AUX 1/2 POST button, it is also possible to configure the bus for

monitoring purposes. Additionally the AUX 1/2 channels are available at the DIGITAL AUDIO IN-

TERFACE.

38 - AUX 1/2 SENDS

This output provides connection for an external FX unit or, when used for monitoring, a power

amplifier or active stage monitor speaker systems. Using the AUX 1/2 fader allows setting the out-

put level in a wide range up to +20 dBu. The AUX 1/2 SEND is designed in Ground Sensing tech-

nology to prevent the induction of external noise, even with long cables. Use balanced cables for

the connection of external components whenever it is possible.

39 - AUX POST

As already previously described, this switch allows determining whether Pre- or Post-Fader sig-

nals are present at the AUX 1/2 channel. The corresponding yellow LED signals when the switch

is engaged and all input channel AUX 1/2 controls are assigned post fader.

40 - MUTE

The MUTE button mutes the AUX output signal. PFL signals are not affected.

41 - PFL

Through this button you can route the pre AUX 1/2 fader signal to the headphones bus. The signal

is outputted for listening via the headphones output. The setting of the AUX 1/2 fader is not rel-

evant for the signal’s volume (Pre Fader Listen). The meter instrument in the master section is

simultaneously switched, so that the left LED-chain indicates the level of the actually chosen

channel (in dBu), leaving you with the opportunity for adjusting the level without routing it to the

AUX 1/2 SEND bus.

42 - AUX 1/2

FADER

This fader controls the summed audio signal at the AUX 1/2 SEND output. When used for moni-

toring, this fader lets you control the volume of the monitor system. When using the DIGITAL AU-

DIO INTERFACE for recording this fader also controls the volume of sent channels USB 3 or

USB 4. See page 19 for details about using the DIGITAL AUDIO INTERFACE.

2.5 MON 1/2

43 - MON 1/2 SOCKETS

OUTPUTS

This output provides connection for an power amplifier or active stage monitor speaker systems.

Using the MON 1/2 fader allows setting the output level in a wide range up to +20 dBu. The

MOUN 1/2 OUTPUTS – like any other XLR-type output on the CMS – is relay-switched to prevent

power-on noise when switching the mixer on or off. Use balanced cables for the connection of

external components whenever it is possible to prevent the induction of external noise.

INSERTS

The low impedance output of these stereo phone-type jacks for MON 1 and MON 2 with breaker

function is assigned to the tip (send) and the high impedance input (return) is assigned to the

ring of the connector. These jacks allow incorporating external third octave band or octave band

EQs, compressors, limiters, de-noisers, etc. into the MON channel. The insertion point is pre

MON faders. As well as with the inserts of the monaural input channels, different DIRECT OUT

functions can be accomplished. Please, also refer to the corresponding description on page 7.

CMS

3

19

44 - FEEDBACK FILTER

The feedback filter is a very narrow banded notch filter, which is only active in a range that is extremely susceptible for

acoustical feedback. The FEEDB. FILTER rotary control sets the corresponding frequency range. Pressing the corre-

sponding button activates the filter. Several circumstances and conditions have an influence on how sensitive or insen-

sitive your system is for acoustical feedback. The following notes are meant to assist you in avoiding feedback and you

should take them into consideration even before you activate the feedback filter.

Best practice for avoiding feedback

1. Do not position the main speaker systems behind the microphones.

2. Switch off all microphones that are not in use.

3. Consider the microphones’ different polar patterns and characteristics, when placing the monitor speakers.

4. Do not turn up the monitor system’s volume higher than actually necessary.

5. Try to avoid extensive equalization on channels that you want to include in your monitor mix.

6. Keep in mind, that a microphone “behaves” different when somebody stands right in front of it.

7. Position the microphones as direct as possible to the sound source.

If you still have the feeling that the monitor system’s acoustic output is not sufficient, after considering the above men-

tioned precautions, you can use the FEEDBACK filter to mute the frequency that tends to generate feedback the most.

Therefore, you have to perform the following steps:

Increase the MON 1/2 level until the limit is reached where feedback starts. The slightly “hovering” sound that you hear

is generated by the system itself. Switch on the feedback filter, turn the rotary control and set it at the mark where the

“sound” disappears. Switching the filter on and off lets you easily check whether you tuned in the correct frequency.

The feedback filter attenuates the level of the corresponding frequency band by about 9 dB. Since the filtered band is

extremely narrow, an alteration in the sound of your monitor system is hardly audible.

CAUTION: Please be extremely careful in driving the system just below the feedback limit. Careless operation,

resulting in feedback noise at high SPL, can cause severe damage to your speaker systems and – even

more important – the human ear.

45 - MUTE

The MUTE button mutes the MON 1/2 output signal. PFL signals are not affected.

46 - PFL

Through this button you can route the pre MON 1/2 fader signal to the headphones bus. The signal is outputted for lis-

tening via the headphones output. The setting of the MON 1/2 fader is not relevant for the signal’s volume (Pre Fader

Listen). The meter instrument in the master section is simultaneously switched, so that the left LED-chain indicates the

level of the actually chosen channel (in dBu), leaving you with the opportunity for adjusting the level without routing it

to the MON 1/2 bus.

47 - MON 1/2

FADER

This fader controls the summed audio signal at the MON 1/2 output. When using the DIGITAL AUDIO INTERFACE as out-

put, and the Studio routing is selected (see page 27), this fader also controls the volume of sent channels USB 1 or

USB 2.

48 - USB 2.0

The USB interface of the CMS is a USB B (female) connector. Please refer to chapter “DIGITAL AUDIO INTERFACE” on

page 30 for more details.

CMS

3

20

2.6 MASTER with GEQ

49 - MASTER LED DISPLAY

The CMS offers two 12-segment LED-chains for opti-

cal monitoring the output levels of the L/R master sig-

nals. The indication range of the LED-meter is 40 dB,

indicating the levels that are present at the master

outputs in dBu. The meter’s 0 dB mark is referenced

to a 0 dBu output signal at the mixer output. As soon

as a PFL button is engaged, the PFL LED lights. The

meter instrument in the master section is simultane-

ously switched, so that the left LED-chain indicates

the level of the actually chosen channel (in dBu). The

right LED-chain indicates the level of the summed

post-fader master output.

50 - MUTE

The MUTE button mutes the MASTER L/R output sig-

nal. PFL signals are not affected.

51 - PFL

Engaging the master PFL button, the pre fader mono

master signal is routed to the headphones bus, so that

it can be monitored via headphones output. The vol-

ume of this signal is not affected by the setting of the

MASTER fader. The meter instrument in the master

section is simultaneously switched, so that the left

LED-chain indicates the level of the summed pre-fader

L/R master signal channel (in dBu), which basically is

the master bus level, while the right LED indicates the

level of the summed post-fader master output.

52 - MASTER L/R

FADER

Level controls to adjust the output signals of the left

and right master outputs (MASTER).

CAUTION: Please, make sure to set the input chan-

nel faders or at least the master faders

to their minimum position, or to engage

the STANDBY switch, before connecting

an external sound source to an input of

the CMS. This will save you, your audi-

ence, and the equipment from unneces-

sary stress.

53 - STANDBY

Pressing the STANDBY switch mutes the output sig-

nals at the MASTER A OUT L/R, MASTER B OUT L/R,

AUX 1/2 and MON 1/2 outputs. The outputs FX 1/2

and REC SEND L/R are still operational. The STANDBY

LED lights indicating that stand-by mode is engaged.

All audio signals coming from the input channels are

not output via MASTER A OUT L/R, MASTER B OUT L/

R, AUX 1/2 and MON 1/2 outputs. However, audio sig-

nals connected via 2TRACK IN or the DIGITAL AUDIO

INTERFACE (see Play USB to 2TRACK on page 28) are

still outputted, providing you with a very comfortable

solution to play intermission music during perform-

ance breaks.

CMS

3

21

54 - MASTER A OUT L/R

The mixer’s electronically balanced main outputs carrying the post master fader L/R signals for connection of the main

PA. The MASTER outputs are switched via output relay with a delay of approx. two seconds after the mixer has been

powered on, which prevents power-on noise when switching the mixer on or off.

Please also refer to the chapter “Setting up a standard PA system”.

55 - MASTER A INSERTS L/R

Stereo phone jacks for left and right channels with breaker function. The low impedance output is assigned to the tip

(send) and the high impedance input (return) is assigned to the ring of the connector. This jack allows incorporating

external third octave band or octave band EQs, compressors, limiters, de-noisers, etc. into the master’s signal path. The

insertion point is pre master faders. As well as with the inserts of the monaural input channels, different DIRECT OUT

functions can be accomplished. Please, also refer to the corresponding description on page 7.

56 - MASTER B OUTPUTS L/R

At the MASTER B OUTPUTS the L/R master audio signal is present that can be used for additional monitoring, side fill

and “next door” applications, or for the connection of a delay-line or subwoofer. The output is pre/post- and also stereo/

mono-switchable.

57 - MASTER B

This control allows adjusting the level of the MASTER B output. The signal levels at MASTER A OUT L/R and MASTER B

OUTPUTS L/R are identical if the MASTER B control is set to the position „5“ and the PRE/POST switch is set to POST.

58 - PRE/POST

OF MASTER B

When PRE is selected the MASTER B is outputted pre master faders (and, if used, pre GEQ), i.e. the level at the MASTER

B OUTPUTS is independent from the master faders settings. When POST is selected the MASTER B is outputted post

master faders, i.e. the level at the MASTER B OUTPUTS depends on the setting of the master faders.

Controlling a connected Sub’s level via master fader makes sense when using an active subwoofer. For monitoring ap-

plications, e.g. side fill on the stage, using the pre-fader setting seems more reasonable.

59 - STEREO/MONO

OF MASTER B

When STEREO is selected the MASTER L/R signal is not changed and outputted in stereo. When MONO is selected the

MASTER L/R signal is summed and outputted in mono at MASTER B L and also MASTER B R. Using MONO is recom-

mended when mono subwoofers are connected to MASTER B outputs.

60 - PHONES

JACK

Stereo phone jack for the connection of headphones with an impedance of 32 to 600 ohms. The audio signals of the

channels with PFL buttons engaged is outputted via this connector. The phones output presents the master L/R signal

when there is no PFL button engaged. Headphones or in ear monitor systems with an impedance below 32 ohms can

be connected. In this case the maximum reachable volume is reduced.

61 - PHONES

CONTROL

This control sets the volume of the headphones connected.

CAUTION: Make sure to set the control to its minimum position before connecting headphones. Permanent hear-

ing loss may occur if headphones are used at high volume.

62 - REC SEND L/R

These RCA-type connectors carry the pre fader master L/R signal. The signal is not affected by the setting of the master

faders and therefore mostly used for the connection of cassette decks, open reel tape decks or DAT recorders for re-

cording purposes. Use the REC SEND & USB OUT control to adjuste the output level.

CAUTION: On most recorders the input signal is directly carried through to the outputs. In case you have con-

nected both, the REC SENDS and the 2TRACK IN, and the CMS’s 2TRACK to MASTER control is set to

anything but its lowest setting, the recorded signal is included in the master mix again. The difference

in delay of the two signals is responsible for dropouts and general degradation of the sound. In the

worst case, activating the RECORD button on your tape deck could lead to very unpleasant feedback

noise. To prevent this from happening make sure to set the 2TRACK to MASTER control to their lowest

settings.

CMS

3

22

63 - 2TRACK IN L/R

Here you can connect a recorder, a CD/MP3 player, an

open reel or an additional SUB-mixer. The signal is

post master fader and post STANDBY switch, which

allows playing intermission music during performance

breaks or checking the mix during the rehearsal, using

the headphones. You just have to engage the STAND-

BY switch to mute all channel signals at the master

outputs. The 2TRACK IN signal however will pass un-

obstructed.

HINT: The 2TRACK IN signal is not available at the

REC SEND connectors, the DIGITAL AUDIO

INTERFACE or the MASTER B OUTPUTS in

PRE fader mode.

64 - 2TRACK

TO MASTER

This control is used to mix the 2TRACK signal to the

master mix, post fader of the master controls.

CAUTION: When adjusting the level of the device

that is connected to the 2TRACK IN –

CD player, tape deck, etc. – always

begin with the 2TRACK to MASTER con-

trol set at its minimum setting. Other-

wise, depending on the output quality

of the connected sound source, the out-

putted level can instantly “hit the top”.

65 - REC SEND & USB OUT

This control allows adjusting the volume at the REC

SEND outputs or, when used, the level of the DIGITAL

AUDIO INTERFACE output channels.

66 - LAMP 12V/5W

This XLR-type socket provides a DC voltage of 12V/

5 watts and is meant for the connection of a goose-

neck lamp. Please make sure that the used lamp com-

plies with the here mentioned specifications and pin

assignment. We recommend using the gooseneck

lamp (DC-LITLITE-4P), available from the DYNACORD

accessory assortment. For further information, please

consult your local dealer.

67 - 11-BAND STEREO GRAPHIC EQUALIZER

The master channel employs a 11-band stereo equal-

izer, which gets activated through the use of the ON

button. The EQ’s insert point is post master fader and

pre power amplifier. The EQ is bypassed when the EQ

ON switch is not locked in its “ON” position. Eleven

frequency bands offering 10 dB boost/cut and a qual-

ity of Q = 2 allow shaping the overall sound to meet

your personal preferences or to optimally match it to

the acoustic conditions of different locations.

Illustration 2-18: Pin assignment of LAMP 12V/5W output

Page is loading ...

DYNACORD CMS1000-3 Owner's manual

This manual is also suitable for

DYNACORD CMS1000-3 Owner's manual

in other languages

Related papers

Other documents