MULTIPLEX Fresh Blender Water Filtration Retrofit User manual

Type
User manual

MULTIPLEX Fresh Blender Water Filtration Retrofit can be installed on compatible MULTIPLEX FreshBlender units to provide filtered water for your blended beverages. It features easy installation with a bracket that hangs on the back of the unit and four self-tapping screws. The kit includes a pre-filter and a filter that should be replaced regularly to ensure optimal performance. After installation, you can verify the operation by entering the Service Menu and dispensing water. Enjoy fresh, filtered water in your blended drinks with the MULTIPLEX Fresh Blender Water Filtration Retrofit.

MULTIPLEX Fresh Blender Water Filtration Retrofit can be installed on compatible MULTIPLEX FreshBlender units to provide filtered water for your blended beverages. It features easy installation with a bracket that hangs on the back of the unit and four self-tapping screws. The kit includes a pre-filter and a filter that should be replaced regularly to ensure optimal performance. After installation, you can verify the operation by entering the Service Menu and dispensing water. Enjoy fresh, filtered water in your blended drinks with the MULTIPLEX Fresh Blender Water Filtration Retrofit.

Instruction Sheet Subject: FreshBlender Water Filtration Retrofit
SCOPE: ALL MULTIPLEX FRESHBLENDER UNITS
1 of 3
 DocumentNumber:020007984 June06,2022
MULTIPLEX
645 PARK EAST BLVD SUITE 5, NEW ALBANY, IN 47150
800-689-0157 OR 844-724-CARE
WWW.MULTIPLEXBEVERAGE.COM
Refreshing the Experience
This water filtration kit bracket is only compatible with units
that have a drain shelf similar to picture below. This kit is
NOT compatible with units that have enclosed drain boxes.
TOOLS REQUIRED
Puncture Resistant Gloves
Clean Bucket
Clean Towels
Drill (cordless recommended)
Universal Screw Driver
Permanent Marker
3/32” Metal Drill Bit
3/8” Drive Socket or Wrench
PARTS REQUIRED
020007985 Water Filtration Kit
nWarning
PowerOFFthemachineandunplugfrompowersource,
this unit contains sharp moving parts. Wear gloves to
protect hands.
Important
Keep refrigeration cabinet door closed so product
remains chilled while unit is off.
PREPARATION
1. Review literature packet included with parts and filters.
2. Power unit OFF using power switch on top right of unit
and unplug.
3. Installation of new water filtration kit will be on back
ofmachine.Withoutdamagingwaterordrainlines,
carefully move machine away from wall.
4. Place bucket under rear drain.
5. Turn off water shutoff valve and disconnect water line
from back of machine.
2 of 3
DocumentNumber:020007984 June06,2022
Subject: FreshBlender Water Filtration Retrofit
INSTALLATION
6. Carefully hang water filtration bracket on back of unit as
shown below.
7. Position water filtration bracket so it does not extend
past the side of the unit. Make sure water filtration
gauges do not come in contact with the drain funnel.
8. Hold Assembly firmly against machine and mark the
location of the two holes in the bracket onto the rear of
the unit.
9. Remove water filter bracket and carefully pre-drill holes
in rear of unit with 3/32” drill bit to a maximum depth of
1/4”(6.35mm).
10. Hold Assembly firmly against machine and drill 2 self-
tapping screws in holes. Start with the bottom hole first.
11. Tighten the four (4) nuts located behind the gauges with
3/8” Drive Socket.
12. Use permanent marker to write install date on each filter.
13. Carefully insert the Pre-filter in the left assembly slot.
Carefully insert the Filter in the right assembly slot.
Pre-filter Filter
14. Connect water inlet line to left water line of assembly.
15. Connect water at rear of unit and turn ON water
shutoff valve.
16.Hold water line from right of assembly over bucket and
flush water line by pressing open quick connect. Flush
line for minimum of 5 minutes and until water is no
longer cloudy.
3 of 3
 DocumentNumber:020007984 June06,2022
Subject: FreshBlender Water Filtration Retrofit
17. Connect right water line of assembly to machine.
REASSEMBLY
18. Move machine back in place.
19. Verify drain is connected correctly.
20. Plug unit to power source and power ON.
VERIFY OPERATION
21. Enter the Service Menu.
A. Menu screens are hidden and will require a
password.Fromstartscreen,touchthethreecorners
in the order shown to access the password screen.
B. Enter password for SERVICE MENU and then press ENTER.
1 2
3
22. Empty water from system.
C. Press SERVICE OUTPUT.
D. Press DISPENSE & BLEND.
E. Toggle WATER DISPENSE option to ON.
F. Water will dispense into dispense area.
G. Screen will time out and return to previous screen.
H. Press BACK or LOGOUT until return to main screen.
23. Make a drink with manager present to confirm operation.
  • Page 1 1
  • Page 2 2
  • Page 3 3

MULTIPLEX Fresh Blender Water Filtration Retrofit User manual

Type
User manual

MULTIPLEX Fresh Blender Water Filtration Retrofit can be installed on compatible MULTIPLEX FreshBlender units to provide filtered water for your blended beverages. It features easy installation with a bracket that hangs on the back of the unit and four self-tapping screws. The kit includes a pre-filter and a filter that should be replaced regularly to ensure optimal performance. After installation, you can verify the operation by entering the Service Menu and dispensing water. Enjoy fresh, filtered water in your blended drinks with the MULTIPLEX Fresh Blender Water Filtration Retrofit.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI