2. Sealey
  3. AP1640
AP1640

Sealey AP1640 User manual

  • Hello! I've reviewed the user manual for the Sealey Woodworking Bench AP1640. This document details the assembly and safety guidelines for the bench, which features a rubber wood construction, tool well, drawers, vice, bench stops and jacks. I'm ready to assist you with any questions you may have.
  • What material is the workbench made of?
    What are the overall dimensions of the workbench?
    How many drawers does the workbench have?
    What is the model number of the workbench?
1.52M WOODWORKING BENCH WITH 4
DRAWERS
MODEL NO: AP1640
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this bench.
9 Locate the bench in a suitable work area.
9 Keep the work area clean, uncluttered and ensure there is adequate lighting.
WARNING! Use the bench on level and solid ground, preferably concrete.
9 Keep the bench clean and tidy in accordance with good workshop practice.
9 Keep children and unauthorised persons away from the work area.
8 DO NOT use the bench for any purpose other than for which it is designed.
8 DO NOT undertake work on the bench without the workpiece being adequately secured.
8 DO NOT use the bench outdoors.
8 DO NOT clean the bench with any solvents which may damage the surface or the protective coating on the worktop.
8 DO NOT get the bench wet or use in damp or wet locations or areas where there is condensation.
2. INTRODUCTION
Made from Rubber Wood. Features tool well, shelf, 4 tool drawers, front vice, four metal bench stops and four wooden board jacks.
Supplied with 4 Wooden Pegs and 4 Anvil Pegs.
3. SPECIFICATION
Model No: ................................................................. AP1640
Overall Size (W x D x H): .......... 1520mm x 620mm x 820mm
Worktop: .........................................................1520 x 500mm
4. CONTENTS
Refer to
instruction
manual
AP1640 Issue:2 (4) 04/07/22
Original Language Version
© Jack Sealey Limited
Tool Well: ........................................................ 1110 x 410mm
Drawer(x4): ...............................................460 x 390 x 80mm
Vice (x1): ............................... 280mm wide x 180mm opening
Part
no.
Description Quantity
1 Table top 1
2 Shelf 1
3 Cross brace 2
4 Leg 2
5 Vice 1
6 Screw 60mm 4
7 Bolt 90mm 4
8 Connecting nut 4
9 Hex wrench 50mm 1
10 Wood peg 4
11 Anvil peg 4
12 Washer 8
13 Screw 30mm 32
14 Screw 35mm 6
15 Sliding partition 1
16 Lower support 2
17 Drawer front panel (P1) 4
18 Drawer back panel (P2) 4
19 Drawer panel (P3) 4
Original Language Version
© Jack Sealey Limited
20 Drawer slot panel (P4) 4
21 Drawer bottom (P5) 4
22 Drawer handle 4
23 Drawer screw (40mm) 8
5. ASSEMBLY
5.1.
5.2.
5.3.
5.4.
.
Step 1: Insert the cross nut with groove (8) into the
frame strut (3). Align the cross nut so that the groove is
horizontal.
Step 2: Fasten the frame to the foot (4) with 2pcs of 90mm
screws (7).
Step 3: After both feet have been attached to the frame
strut, the shelf (2) is pushed into the groove.
Step 4: Align the second frame strut (3) and fasten it with
the connecting nuts with groove (8) and 2 pcs of 90mm
screws (7) on the foot (4). The shelf must snap into the
groove of the frame strut.
Step 5: The lower support (16) is attached to the front with
4 pcs of 35mm screws (14) at both ends of the feet.
Step 6: The lower support(16) is also attached to the
partition wall with rails (15) using 2 pcs of 35mm screws
(14).
AP1640 Issue:2 (4) 04/07/22
Original Language Version
© Jack Sealey Limited
Step 7: The legs are then attached to the worktop with 4
pcs of 60mm screws (6), 2 pcs per leg.
Step 8: The partition is also attached to the frame with 2
pcs of 35mm screws (14). WARNING! there are no pre
drilled holes.
Step 9: Attach handles (22) to the front of the drawer (17)
with 8 pcs of 40mm drawer screws (23), 2 pcs per drawer.
Step10: The two side parts of the drawer (19 & 20) are
attached to the front of the drawer with 2 pcs of 30mm
screws (13) per side, 4 pcs per drawer.
Step11: The back of the drawer (18) is attached to the two
side parts by using 4 pcs of 30mm screws (13), 2 pcs per
side. Then insert the bottom of the drawer. Step12: After installing the drawers, check whether the
inner tracks of the drawer pull outs are pushed all the way
forward if not, then push all the way forward.
Step13: When inserting the drawers, make sure the runner
clip is facing forwards see picture, then slide the drawers
into the guides.
Step14: Fasten the holding rods (10) and the bench hooks
(11) in the holes provided in the worktop.
AP1640 Issue:2 (4) 04/07/22
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Original Language Version
© Jack Sealey Limited AP1640 Issue:2 (4) 04/07/22
/