Blaupunkt CD169 User manual

Brand: Blaupunkt

Model: CD169

Category: Car media receivers

Type: User manual

KEY WEST CD169

High-Power FM/AM/CD Receiver with Detachable Face

Robert Bosch Corporation

Sales Group —

Blaupunkt Division

2800 South 25th Avenue,

Broadview, Illinois 60153

288E8741

Bosch Group

168 WATTS

KEY WEST CD169

PWR

MUTE

OPEN

SENS

SC/PS

AUD

XBASS

RPT

MIX

KEY WEST(En)_Cover 23/3/99, 1:33 PM1

E-1

Precautions

This equipment has been tested and found to comply with the

limits for a Class B device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable pro-

tection against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate radio

frequency energy, and, if not installed and used in accord-

ance with instructions, may cause harmful interference with

radio communications. However, there is no guarantee that

radio interference will not occur in particular installation. If this

equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to consult the dealer

or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not ex-

pressly approved in this manual could void your authority to

operate this equipment.

Features

• Detachable Flip down front panel

• Built-in power amplifier

(max. output : 42W × 4ch)

• FM/AM PLL Synthesizer tuner

• 30 Station preset memory

• Travel Store / Scan tuning

• X-BASS System

• Station name store / Station call

FCC WARNING

• Avoid installing the unit where it would be subject to high

temperatures, such as in direct sunlight or a hot air stream

from the heater, or where it would be subject to dust, dirt, or

excessive vibration.

• Do not turn on the unit if the temperature inside the car is

very high. Always cool down the unit before usage. Parking

your car in direct sunlight will result in a temperature rise.

• If the unit does not turn on, check the connections first. Then

check whether the fuse at the back of the unit is blown.

• Carefully read this manual before using the unit. If you en-

counter any problems that are not covered in this manual,

please consult the dealer where you purchased the unit or

the dealer nearest to you.

• This unit has been designed specifically for playback of com-

pact discs bearing the

mark. Other discs cannot be

played.

Handling Compact Discs

• Be careful when removing a compact disk after the play-

back is completed because the disk may be extremely hot.

• Do not expose compact discs to direct sunlight or any heat

source.

• Check all compact discs before playing, and discard cracked,

scratched or warped discs.

• Wipe dirty or damp discs outward from the center with a

soft cloth.

• Do not use any solvents such as commercially available

cleaners, antistatic spray, or thinner to clean the compact

discs.

Attaching the Front Panel

Place the right hand side of the front panel so that the parts

A of the front panel are engaged with the parts B of the unit

as shown below. Then push the left hand side of the front

panel until it is securely locked.

Handling the Front Panel

Front Panel Open / Close

Panel open

Press the

OPEN

Panel close

Raise the front panel with your

finger until it locks in place.

KEY WEST (En)_P1-10 3/23/99, 2:30 PM1

E-2

Notes

• Be sure to use this unit with the front panel closed.

The unit is automatically switched off when the front panel

is left open for about 10 minutes.

• Do not handle the unit roughly when opening/closing the

front panel.

• Do not put any object or use it like a tray when the front

panel is open in a lying position.

• Do not press the OPEN button when closing the front panel.

• Do not put much force to the operation buttons or the dis-

play window as it may cause damage or deform the unit.

• Connectors on the unit and front panel are vital parts trans-

mitting the signal. Do not touch, push and scratch them.

• Be careful not to pinch your fingers or hands when opening

and closing the front panel.

• Do not press hard on the front panel when affixing it to the

unit. No more than light to moderate pressure should be

needed.

• Make sure there is no dust or dirt on the electrical terminals

on the back of the front panel as this could cause intermit-

tent operation or other malfunctions.

Identification of Controls

1 OPEN button

2 PWR button

Turns the power of the unit on or off.

3 TUN/TRK button

Used to tune in to the desired station.

4 LCD Display window

5 CD button

Switches the CD playback mode.

6 BND/TS button

Selects the AM/FM Band & Travel Store.

7 DISP button

Mode selector. Clock adjustment. Display priority setting.

8 MUTE/SENS button

Muting the sound. Switches the seek sensitivity between

local and distance.

9 XBASS button

Boosting the bass sound.

10 PRESET MEMORY button

During radio reception :

; For Preset memory

During CD mode :

4/MIX

; For Mix play

5/RPT

; For Repeat play

; For Pause

11 SC/PS button

Scan tuning. Preset scan tuning. Scan play in CD mode.

12 AUD button

Audio control selector; Bass, Treble, Loudness, Balance

& Fader.

13 Dial

Adjusts the volume level/bass/treble/balance/fader.

Storing the station names. Select Alpha-numeric charac-

ters.

168 WATTS

KEY WEST CD169

PWR

MUTE

OPEN

SENS

SC/PS

AUD

XBASS

RPT

MIX

123

3.Close the inner cover.

Do not leave inner cover in the down position unless the

front pannel is in place.

Detaching the Front Panel

2.Pull the front panel toward your direction to remove it.

1.Press the

OPEN

firmly to open the flip down front panel.

Security

Bolt the front panel with the screw (supplied) in the inner

cover as shown below, to protect the front panel from

robbery and from getting lost.

EJECT button

Ejecting the CD

Press recessed button located to the left behind the Front

Panel.

SCREW

KEY WEST (En)_P1-10 3/23/99, 2:30 PM2

E-3

General Operations

Volume Level Control and Memory

Rotate the dial to set the memory for the volume level which

will be recalled when the unit is turned on.

1. Adjust the volume level. Spinning or fast rotation of the

dial knob will increase the number of turns needed to

reach max. volume.

2. Hold the

PWR

pressed for more than 2 seconds.

The unit will turn off and the selected max. turn-on

volume level is set in memory.

Note

If the unit is turned off with the volume lower than the memory

setting, the unit will return to the lower setting when turned

back on.

Muting the sound

Press

MUTE / SENS

“ MUTE ” apeares on the display window.

To restore the previous volume level, press

MUTE / SENS

again.

Setting the Clock

1. Turn the ignition key to the ON position.

2. Press the

PWR

to turn on the unit.

3. Press the

DISP

to display “ CLK ADJ ”.

A. Press the

MUTE / SENS

within 3 seconds to flash the “ 12 ”

(HOUR ADJ).

B. Rotate the dial to set the hour digit.

C. Press the

MUTE / SENS

to flash the “ 00 ” (MIN ADJ).

D. Rotate the dial to set the minute digit.

Volume down

Volume up

4. Press the

DISP

to display “ CLOCK 12 ”.

5. Rotate the dial to select the 12 or 24-hour time mode.

Each time you rotate the dial, the mode changes or

toggles as follows;

CLOCK 12

ÔÔ

Ô CLOCK 24

6. Press the

DISP

momentarily. The clock is activated.

Ignition-off Clock Recall

The display will illuminate showing the time and then auto-

matically shut off after 5 seconds.

Press the

DISP

while the ignition switch is in the “ OFF ” posi-

tion.

Mode Selector

Each time the

DISP

is pressed, the display window will change

over as shown below;

Priority ➜ STN CALL ➜ LEVEL 1 ➜ Temporary ( NO NAME )

CLOCK 12 CLK ADJ METER 1

Display priority setting

Display Priority can be set for the following two items;

• Frequency and Station Name.

Example

To set Station Name to the Display Priority.

1. Press the

DISP

three times, and the temporary display

appears in the display window.

2. Hold the

DISP

pressed for more than 2 seconds.

“ NO NAME” or any station name blinks once to indicate

that Station Name is selected for the Display Priority.

After 5 seconds, the display mode will automatically re-

turn to the Display Priority showing either “NO NAME” or

the station name.

Tip

Frequency Display is initially set as the Display Priority,

and Station Name (“NO NAME”) is set to “Temporary”.

Adjusting the Sound Characteristics

1. Press the

AUD

to select the desired adjustment mode.

BASS 0 ➜ TREBLE 0 ➜ LOUD OFF(LOUDNESS)

R0 F0(FADER) L0 R0(BALANCE)

2. Rotate the dial to adjust the selected item.

Adjust within 3 seconds after selecting the item.

After 3 seconds, the dial functions as volume control.

Use the following tables as a guide for adjusting the set-

tings in each mode.

BASS BASS -5 BASS +5

TREBLE TREBLE -5 TREBLE +5

LOUD LOUD OFF LOUD ON

BALANCE L9 R0(Full left) L0 R9(Full right)

FADER R9 F0(Full rear) R0 F9(Full front)

➜

KEY WEST (En)_P1-10 3/23/99, 2:30 PM3

E-4

Radio Reception

Receiving the Memorized Stations

1. Press the

BND / TS

to select the desired band.

2. Press the

momentarily.

Local/Distant (LO/DX) Selection

This feature is used to select the strength of the signals at

which the radio will stop during Seek Tuning.

Press the

MUTE / SENS

for more than 2 seconds to select the

Local setting and only strong (local) stations will be received.

The “ lo ” indicator appears on the display window.

Pressing again will select the Distant setting and the radio

will stop at a wider range of signals, including weaker more

distant stations. The “ lo ” indicator will go out on the display

window. DX is the suggested default setting.

Preset Scan Tuning

1. Press the

BND / TS

to select the desired band.

2. Hold the

SC/PS

pressed for more than 2 seconds.

“ SCAN ” indicator will appear on the display window.

The unit will scan preset memory for the 12 stations from

the AM/AT band or the 18 stations from the FM 1/FM 2/

FT bands. The unit will stop at each preset station for 8

seconds, before continuing to the next preset station.

Press the

SC/PS

again to stop Preset Scan Tuning and

remain this on the selected frequency.

Memorizing Stations Automatically (Travel Store)

1. Press the

BND / TS

to select the desired band.

2. Hold the

BND / TS

pressed for longer than 2 seconds.

Up to 6 stations with strong signals will be automatically

stored in preset memory for the selected band.

Note

This function is available for FT and AT.

Memorizing Only the Desired Stations

You can store up to 6 stations on each band (18 for FM 1, FM

2 and FT, 12 for AM and AT) in the order of your choice.

1. Press the

BND / TS

to select the desired band.

2. Press the

TUN/TRK

to tune in stations.

3. Press and hold the desired preset memory button

for about 2 seconds until the frequency indicator

flashes twice.

The number of the pressed preset memory button ap-

pears on the display window.

Note

If when you store another station on the same preset number

button, the previously stored station is replaced with new one.

Seek Tuning

1. Press the

BND / TS

to select the desired band.

FM 1 ➜ FM 2 ➜ FT ➜ AM ➜ AT

FT & AT are Travel Store bands.

2. Press the

TUN/TRK

to tune in stations. Tuning automati-

cally stops at a broadcasting frequency.

“ SEEK ” indicator will appear on the display window.

When tuned in to FM stereo broadcasting stations, the

“

” stereo signal indicator will appear on the display

window.

Manual Tuning

1. Press the

BND / TS

to select the desired AM or FM band.

2. Press the

TUN/TRK

for more than 0.5 sec-

ond to activate the manual tuning mode. Press again to

tune in to stations.

“ MANUAL ” indicator will appear on the display window.

After 4 seconds of completing Manual Tuning, the tuning

control will revert to the Seek Tuning mode.

Scan Tuning

1. Press the

BND / TS

to select the desired band.

2. Hold the

SC/PS

pressed for less than 2 seconds.

The unit will scan the selected band for stations.

“ SCAN ” indicator will appear on the display window.

Press the

SC/PS

again to stop Scan Tuning and remain

this on the selected frequency.

Tip

While tuning, the pie-shaped signal-strength meter

on the display is lit differently depending on the strength

of the signal. While scanning bands, the pie-shaped sig-

nal-strength meter spins. While playing CD’s, this display

spins also.

KEY WEST (En)_P1-10 3/23/99, 2:30 PM4

E-5

Storing the station names

You can assign a name to each radio station and store it in

memory. As many as 30 station names can be stored, com-

posed with 8 characters each.

Storing the station names

1. Tune in a station whose name you want to store.

2. Press the

DISP

for more than 2 seconds.

The “ NAME EDT ” will light then the “ _ _ _ _ _ _ _ _ ” on

the display window. The first “ _ ” flashes.

3. Enter the characters.

A. Rotate the dial in a clockwise direction to select the

desired characters.

(A➜B➜C➜...Z➜

<➜>➜∗➜+➜

′

➜−➜′➜/

➜0➜1➜2➜3...9➜“ ”Space )

B. Press the

TUN/TRK

to move the flashing cursor to

the next position. If you press

TUN/TRK

, the flash-

ing cursor moves to the left.

C. Repeat steps A and B to complete entering the

entire name 8 characters max.

Tip

To erase/correct a name, press the

DISP

for more than

2 seconds to clear the character and re-enter.

4. Press the

MUTE / SENS

to store the station name.

The station name flashes.

5. To return to the normal radio reception, Press

DISP

Erasing the station names

1. Tune in any station and press the

DISP

for more than 2

seconds.

2. Press the

MUTE / SENS

The station name or “ _ _ _ _ _ _ _ _ ” is now flashing.

3. Rotate the dial to select the name of the station that you

want to erase. To erase all the name of the station, dis-

play “ ✳ALL DEL ”.

4. Press the

DISP

for more than 2 seconds.

Repeat steps 3. and 4. if you want to erase other names.

5. To return to the normal radio reception, Press

DISP

L-ch Level meter

R-ch Level meter

Direct Access to Memorized Stations via

Station Call

You can search for the memorized AM & FM station names in

the memory.

1. Press the

DISP

to display the “ STN CALL ” on the dis-

play window.

2. Rotate the large dial to select the desired station name.

3. Press the

MUTE / SENS

to tune in the desired station.

Level Meter selection

The meter displays can be selected from four types.

You can select :

• METER 1 : Type that the level meter goes upward.

• METER 2 : Type that only the very top segment lights.

• METER 3 : Type that the remaining segments light. (op-

posite of METER 2)

• METER 4 : Type that the level meter goes up and down

dividing from the center segment.

• METER 0 : No meter is indicated.

1. Press the

DISP

to display the “ METER 1 ” on the display

window.

2. Rotate the dial to select the desired meter indication.

METER 1 ➜ METER 2 ➜ METER 3 ➜ METER 4 ➜ ME-

TER 0

Level Meter Sensitivity selection

The sensitivity of the level meter display can be switched.

You can select :

• LEVEL 1 : Normal sensitivity

• LEVEL 2 : High sensitivity

1. Press the

DISP

to display the “ LEVEL 1 ” on the display

window.

2. Rotate the dial to select the desired meter sensitivity.

LEVEL 1

ÔÔ

Ô LEVEL 2

Enhancing the bass sound

For extended bass centered @ 72Hz, the XBASS function

can be set for either each band and CD mode.

You can select :

• XBASS 1 : Enhanced BASS level (low)

• XBASS 2 : Enhanced BASS level (Middle)

• XBASS 3 : Enhanced BASS level (High)

• XBASS 4 : Enhanced BASS level (Very high)

• XBASS 0 : No BASS enhanced/off

Press the

XBASS

repeatedly to select the bass sound.

“

” appears on the display window.

Each time you press

XBASS

, the current mode appears on

the display window and then the mode change as follows:

XBASS 0 ➜ XBASS 1 ➜ XBASS 2 ➜ XBASS 3 ➜ XBASS 4

KEY WEST (En)_P1-10 3/23/99, 2:31 PM5

E-6

CD Operations

Listening to a disc that is already loaded

Press the

to select the CD mode.

Playback begins automatically.

Pausing Playback

Press the

To resume playback, press the

again.

Stopping Playback

Press the

BND / TS

to select the radio reception (FM 1, FM 2,

FT or AM, AT).

Ejecting Discs

Press the to eject the disc located behind flip-down front

panel.

Notes

• The unit will turn on automatically when a CD is inserted if

the ignition switch is ‘‘ON’’.

• When the disc is ejected from the CD slot, remove it within

10 seconds; otherwise, the disc will be reloaded automati-

cally.

Track Search

Press the

TUN/TRK

during CD mode. Track numbers appear

in the display window.

: Playback starts from the beginning of the next track.

: Playback starts from the beginning of the current track.

Press again to play the previous track.

Playing the CD player

Loading Discs

1. Press the

OPEN

and insert the disc.

2. Close the front panel.

Playback begins automatically.

‘‘ LOADING ’’ indicator will flash in the display window.

Note

Make sure that the front panel is closed when playback

begins.

Playback with the front panel open causes the

unit to turn off automatically in about 10 min-

utes.

! NEVER Insert a 3-inch CDs.

This unit is designed for playback of standard 5-inch CD’s

only. Do not attempt to use 3-inch CD singles in this unit,

either with or without an adaptor, as damage to the player

and/or disc may occur.

Tips

•

When a CD is loaded, the on the display remains lit.

• During playback of a CD, the pie-shaped signal-strength

meter

spins.

Cue / Review

Press and hold the

TUN/TRK

. Release when you have found

the desired point.

: To search forward.

: To search backward.

Scan Play

Press the

SC/PS

during CD mode.

The ‘‘ SCAN ON ’’ indicator appears in the display window.

This will play the first 10 seconds of all the tracks on the disc.

Press the

SC/PS

again to cancel this feature.

Repeat Play

Press the

5/RPT

during CD mode.

The ‘‘ RPT ON’’ indicator appears in the display window and

the current track is played repeatedly.

Press the

5/RPT

again to cancel this feature.

Mix Play

Press the

4/MIX

during CD mode.

All the tracks on the current disc are played in random order.

Press the

4/MIX

again to cancel this feature.

Labelled side up

KEY WEST (En)_P1-10 3/23/99, 2:31 PM6

E-7

Installations

Supplied Mounting Hardware

Sleeve

Bushing Mounting Strap Release

& Screws and Screw Keys

Precautions

• Be sure to detach the front panel before you start in-

stalling the unit.

• When mounting the unit in a car, keep the unit as level as

possible. If the unit must be mounted at an angle, due to the

design of the vehicle, make sure that the unit does not lit by

more than 30˚.

• Choose the mounting location carefully so that the unit will

not interfere with the normal driving operations of the driver.

• Use only the supplied mounting hardware for a safe and

secure installation.

Mounting Example

Installation in the dashboard.

1. Install the sleeve in the dashboard.

2. Select and bend the appropriate tabs to hold the sleeve

firmly in place.

Fire wall

If your car has no accessory position on the

ignition key switch (POWER SELECT switch)

The illumination on the front panel is factory-set to be turned

on even when the unit is not being played. However, this set-

ting may cause some car battery wear if your car has no ac-

cessory position on the ignition key switch. To avoid this bat-

tery wear, set the POWER SELECT switch located on the

bottom of the unit to the

B position, then press the reset

button. The illumination is reset to stay off while the unit is not

being played.

POWER SELECT SWITCH

(Located on the bottom of the unit)

Change the position with a jeweler’s screwdriver, etc.

A : Your car has an accessory position on the ignition

switch.

B : Your car has no accessory position on the ignition

switch.

Be sure to

press the reset button after changing the switch

and connecting the lines.

Reset button

Press the reset button with the point of

a sharp object such as a ball-point pen.

The distance to the fire wall is

various due to the type of the car.

Be sure to secure the unit by

properly inserting the bushing.

Caution

Insufficient fastening of the

screw may cause some CD’s to

skip.

Mounting Strap Use

3. Attaching the Mounting Strap to the underside of the dash

board, using screw.

Attach the back of the unit to the Mounting Strap using

the support stem bolt and hardware.

Bushing Use

3. As shown in the figure below, securely fasten the screw,

which has been inserted into the bushing, to the rear of

the set.

KEY WEST (En)_P1-10 3/23/99, 2:31 PM7

E-8

Connections

Caution

• Connect each pair of speaker leads only to a single speaker

(or speaker system) that has an impedance of least 4 ohms,

as well as 42 watts power-handling capability.

• Do not connect speaker leads to any inputs on external

amplifiers. This will cause damage to the internal amplifier

of this unit.

Connection procedure

Warning

• To prevent short circuit, remove the key from the ignition

and disconnect the battery’s (–) (minus) terminal.

• This unit is designed for negative ground 12 V DC operation

only. You can not use it for 24 V or other types of car batter-

ies.

1 Make sure the car’s ignition key has been removed.

2 Disconnect the minus terminal of the car’s battery.

3 Connect the wiring harness wires in the following

order : GND (Black), BTT (Yellow), ACC (Red) and

ANTENNA REMOTE (Blue), and tape each so they do

not come in contact with each other.

4 Connect the speaker wires of the wiring harness.

5 Connect the car’s antenna terminal to the antenna

socket of the unit.

6 Connect the detachable wire harness to the unit.

7 Reconnect the minus terminal of the car’s battery.

8 Start the car’s engine.

9 Make sure the unit operates properly.

ADDITIONAL

SPEAKERS

EXTERNAL

AMPLIFIER

REMOTE

(IF ANY)

LEFT FRONT

SPEAKER

WHITE W/BLACK STRIPE

LEFT REAR

SPEAKER

WHITE

GREEN

GREEN W/BLACK STRIPE

BLUE

ANTENNA

REMOTE

(IF ANY)

RED

YELLOW

BLACK

DETACHABLE

WIRE HARNESS

PRE-AMP

OUTPUTS

REAR OF UNIT

ANTENNA

SOCKET

BATTERY

(CONSTANT

POWER)

IGNITION SWITCH

GRAY

GROUND

RIGHT FRONT

SPEAKER

GRAY W/BLACK STRIPE

VIOLET W/BLACK STRIPE

VIOLET

RIGHT REAR

SPEAKER

FUSE (10A)

Connection Example

KEY WEST (En)_P1-10 3/23/99, 2:31 PM8

E-9

Maintenance

Removing the Unit

Use the supplied release keys when you need to remove the

unit from the car.

Insert the “ TOP R ’’and “ TOP L ’’of the release keys on the

right and left position until it clicks respectively, to remove the

unit.

Reset button

Replacing the Fuse

If the fuse is blown, check the power connection first and then

replace the fuse. If the fuse blows again under normal condi-

tions, the unit may be defective.

Back of the unit

Warning

Use only a fuse with the specified amperage (10 A).

Use of another type of fuse can result in a fire or unit damage.

Cleaning the Connectors

If the connectors of the unit and the front panel are contami-

nated, malfunctions may occur.

Detach the front panel and clean the connectors with an alco-

hol dampened cotton swab as shown below.

Main unit Back of the front panel

Returning to the Initial Settings

When the reset button is pressed, the microcomputer of the

unit returns to the initial settings. If the display window is not

properly shown or the unit malfunctions, press the reset but-

ton with the point of a sharp object such as a ball-point pen.

As shown in the figure below, push the plate spring firmly to

remove the release keys.

Notes

• Handle the release keys carefully to avoid injuring your fin-

gers.

• Keep the release keys in a safe place for future use.

KEY WEST (En)_P1-10 3/23/99, 2:31 PM9

E-10

CD Player Troubleshooting

When problems occur with CD playback, an error message

appears in the display window.

Refer to the table below to identify the problem, then take the

suggested corrective action. If the “ MECA ERR ” appears or

“ SW ERROR ” persists, contact your nearest Blaupunkt

dealer.

Message Possible cause Recommended action

CD ERROR Dirty disc. Clean the disc.

Scratched disc. Replace the disc.

Up-side-down. Check the disc.

Focus error. Try ejecting and

reinserting under normal

temperature conditions.

Data and focus error. Under normal tempera-

ture conditions, eject

and insert clean, un-

damaged disc properly.

SW ERROR Mechanical problem. Eject and reinsert.

Specifications

GENERAL

Dimensions : Approx. 178 mm × 50 mm × 155 mm

(W × H × D)

Power requirements : 12 volts DC car battery

(negative ground)

Output Power : 42 watts × 4 channels

Output Wiring : Floating-ground type designed for 4

speaker use.

RCA low-level outputs (2 channels).

Output Impedance : Compatible with 4-8 ohm speakers.

Low - Level Output : 2 V.

TUNER

Tuning Range : AM : 530 - 1,710 kHz (10 kHz step)

FM : 87.5 - 107.9 MHz (200 kHz step)

Sensitivity : AM : 20 µV

FM : 1.5 µV

Stereo Separation : 30 dB

CD PLAYER

Frequency

Response : 20 - 20,000 Hz

S/N Ratio : 90 dB

Wow & Flutter : Below the measurable limit

Troubleshooting Guide

The following check will assist in the correction of most prob-

lems which you may encounter with your unit. Before going

through the check list below, refer back to the connection and

operating procedures.

General

Radio reception

Also make sure that antenna is connected, extended and dry

inside.

If the above mentioned solutions do not help to improve the

situation, consult your nearest Blaupunkt dealer or in the

United States call 1-800-266-2528 for technical assistance,

parts and service. Call 1-800-950-2528 for dealer referral or

to request product brochure.

Trouble

Preset stations are not re-

ceivable.

Automatic tuning is not pos-

sible

Travelstore feature does not

complete storing of six sta-

tions.

Cause/Solution

The broadcast is too weak.

→ Use manual tuning.

Not enough broadcast frequen-

cies are receivable.

Cause/Solution

Adjust the volume with the dial.

Set the fader control to the cen-

ter position with a 2-speaker sys-

tem.

Remove the front panel and

clean the connectors with cotton

swab dipped in isoprophyl alco-

hol (90% or higher).

Trouble

No sound

Indications do not appear

on the display window.

KEY WEST (En)_P1-10 3/23/99, 2:31 PM10

Blaupunkt CD169 User manual

Brand: Blaupunkt

Model: CD169

Category: Car media receivers

Type: User manual

Download PDF

report

Blaupunkt CD169 User manual

Blaupunkt CD169 User manual

Related papers

Other documents