Date of Purchase
Upholstered Bed with Storage
Lot Number (TAKEN FROM CARTON)
Thank you for purchasing from DHP!
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
1
VN. - 2022/02/09
© 2021 Dorel Home Products All Rights Reserved
King
Weight Limit:
Bed: 500 lb / 227 kg
Drawer 40 lb / 18 kg
B34429214901 - 36213705
Questions, concerns, missing parts?
CONTACT OUR CUSTOMER SERVICE DEPARTMENT
BEFORE RETURNING PRODUCT TO THE RETAILER.
If parts are missing or damaged, we will gladly ship your
replacement parts free of charge.
Visit www.dhpfurniture.com/eng/replacement-parts
or call Toll-Free 1-800-267-1739.
You can also chat with us at www.dhpfurniture.com
4291049 (Black Faux Leather)
4292149 (White Faux Leather)
2
1-800-267-1739
Monday to Friday
Saturday
Sunday
DHP Consumer Services
12345 Albert Hudon, Suite 100,
Montreal, Quebec H1G 3L1
cs@dhpfurniture.com
Read Before Beginning Assembly
●Work in a spacious area and near where the unit will be used, preferably on a
carpet, or use a piece of the cardboard packaging to protect your floor and product.
●Make sure all parts are included. Most parts are labeled or stamped on the raw
edge.
●Read each step carefully. It is very important that each step of the instructions is
performed in the correct order. If these steps are not followed in sequence,
assembly difficulties will occur.
●This product may contain small components. Please ensure that they are kept
away from small children.
●This product is designed for home use and is not intended for commercial use.
Contact Us!
For help with assembly, identifying parts, product information or to order parts,
please contact us:
Limited 1 year Warranty
DHP warrants this product to be free from defects in material and workmanship
and agrees to remedy any such defect. This warranty covers one year from the
date of original purchase from authorized retailers. This is solely limited to the
repair or replacement of defective parts and assembly labor is not included.
This warranty does not apply to any product which has been improperly
assembled, subjected to misuse or abuse or which has been altered or repaired in
any way.The warranty does not cover wearing, tearing, fading or splitting of the
fabric (where applicable). Liability for consequential damages is excluded to the
extent exclusion is permitted by law. This warranty gives you specific legal rights
and you may also have other rights which vary from state to state or province to
province.
To obtain warranty service, purchaser must present original bill of sale.
Components repaired or replaced are warranted through the remainder of the
original warranty period only. The defective components will be repaired or
replaced without charge, subject to the terms and conditions described above.
Visit www.dhpfurniture.com to view the limited warranty valid in the U.S. and
Canada.
9 am to 9 pm (Eastern Time)
10 am to 6:30 pm (Eastern Time)
11 am to 7 pm (Eastern Time)
Do NOT use
powertools
Chat
with us! www.dhpfurniture.com
1.5 hour
This product is shipped in 2 cartons
PARTS
3
PARTS LIST
HEADBOARD
X 1 PC
BACK PANEL
X 1 PC
FOTTBOARD
X 1 PC
SIDE RAIL
X 2 PCS
CENTER RAIL
X 2 PCS
CROSS RAIL
X 1 PC
SIDE TUBE
X 4 PCS
SUPPORT RAIL
X 2 PCS
SUPPORT LEG
X 4 PCS
WOODEN SLATS
X 39 PCS
4
PART NUMBERS
PART LABELS
4291049
(Black Faux Leather)
4292149
(White Faux Leather)
A
T1019890
T1017420
A1
T1019450
T1019450
B
T1019900
T1017430
E
T1019470
T1019470
F
T1019480
T1019480
G
T1019490
T1019490
H
T1019500
T1019500
J
T1019510
T1019510
K
T1019520
T1019520
P1
T1013900
T1013900
Each part has a unique part number.
Please reference the appropriate part
number when contacting customer
service for replacement parts.
Before throwing any packaging, please
verify all contents and make sure you
have received all the parts listed above!
AA1 E F
J
GP1
H K
B
PARTS LIST
SINGLE SLAT CAP
X 26 PCS
DOUBLE SLAT CAP
X 26 PCS
FRONT PANEL
X 4 PCS
DRAWER BOTTOM PANEL
X 4 PCS
DRAWER BACK PANEL
X 4 PCS
DRAWER SIDE PANEL
X 4 PCS
DRAWER SIDE PANEL
X 4 PCS
CASTER
X 20 PCS
Each part has a unique part number.
Please reference the appropriate part
number when contacting customer
service for replacement parts.
Before throwing any packaging, please
verify all contents and make sure you
have received all the parts listed above!
5
PART NUMBERS
PART LABELS
4291049
(Black Faux Leather)
4292149
(White Faux Leather)
X
T1013930
T1013930
Y
T1013940
T1013940
C
T1019930
T1017470
L
T1019190
T1019190
M
T1019200
T1019200
N
T1019210
T1019210
S
T1019220
T1019220
Q
T1019230
T1019230
X Y C L M
N S Q
6
Please do not completely tighten all the hardware,
until the entire assembly is complete, unless
otherwise indicated in the step-by-step instructions.
The screw(s), bolt(s) to be used at each step are shown
in actual size in the lower right corner of the page.
Hardware Pack
4291049 (Black Faux Leather)
4292149 (White Faux Leather) HP # : T4155449-00
HARDWARE LIST
1
BOLT
X 26 PCS
BOLT
X 4 PCS
WASHER
X 4 PCS
BOLT
X 8 PCS
ALLEN KEY
X 1 PC
BOLT
X 8 PCS
BOLT
X 24 PCS
BOLT
X 56 PCS
BOLT
X 8 PCS
1/4’’ x 3/4’’ 1/4’’ x 3/4’’ 1/4’’ 1/4’’ x 1 9/16’’ 4 mm
6789
5
4321
3/16’’ x 3/8’’ 3/16’’ x 7/8’’ 3/16 x 3/4’’ 1/4’’ x 1/2’’
Step 1
Stịck back panel A1 to the back of
Headboard A with Velcro as Illustrated.
7
Step 2
Attach Guide H X 4 to Headboard A and
Footboard B with bolts ❾.
8
X 8
9
Step 3
Attach support rail J to side rail E with
bolts ❶.
Repeat the same procedure for remaining
part J and E.
9
X 6
1
Step 4
Attach support leg K X 2 to center rail F
with bolts ❶ as shown.
Repeat the same procedure for remaining
part K X 2 and F.
10
X 8
1
Step 5
Attach center rails F X 2 to Headboard A
and Footboard B with bolts ❶.
Attach side rails E X 2 to Headboard A
and Footboard B with bolts .
11
4
X 8
1
X 8
4
Step 6
Attach cross rail G to support rails J x 2
with bolts ❶
12
X 4
1
Step 7
7.1 Insert slat P1 into single slat cap X,
7.2 Press single slat cap X into side rails
E, repeat the same procedure for the
opposite side of the bed with a new slat
P1 and single slat cap X.
Repeat the same procedures going
backwards for every row of slats.
13
Step 8
8.1 Insert double slat cap Y x 2 onto the
ends of slat P1 assembled in previous step;
8.2 Take a new slat P1 and insert both
ends into the other free end of double slat
cap Y x 2, then press double slat cap Y x 2
SIMULTANEOUSLY into center rails F x 2
as illustrated.
Repeat the same procedures going
backwards for every row of slats.
14
Step 9
Attach drawer back panel M to drawer
side panels S and N with bolts .
Don’t completely tighten the bolts until
STEP 12 is completed.
15
7
Make sure that these holes are all located on
the top side before assembling.
For better performance, please orient the
plastic sheet towards inside of the drawer.
X 4
X 16
7
Step 10
16
Attach caster Q to drawer bottom panel L
with bolts .
6
X 8
6
Step 11
17
.
11.1 Attach caster Q X 4 and drawer
bottom panel L to drawer side panels S
and N with bolts .
11.2 Attach drawer bottom panel L to drawer
back panel M with bolt .
7
8
X 8
7
X 32
8
Step 12
18
Attach the sub-assembly L/S/N/M from
previous step to front panel C with bolts .
Then, properly tighten all the bolts.
8
X 24
8
Step 13
19
Attach bolts and washers as shown.
2 3
X 4
X 4
3
2
Step 14
20
Align Drawers with the bed frame and push
them into the bed.
Lock drawers by slightly lifting drawer and
inserting the Pin into the Slot.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
