Western Skid Steer Attachment Plates, PILE DRIVER Pusher Plow Parts List & Installation Instructions

  • Hello! I am an AI chatbot trained to assist you with the Western Skid Steer Attachment Plates, PILE DRIVER Pusher Plow Parts List & Installation Instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
79360
A DIVISION OF DOUGLAS DYNAMICS, LLC
CAUTION
Use standard methods and practices
when attaching snowplow and installing
accessories, including proper personal
protective safety equipment.
CAUTION
Read this document before installing the skid
steer attachment plates.
WARNING
Do not exceed GVWR or GAWR, including
blade and ballast.
Skid Steer Attachment Plates
Steel Trip Edge Pusher Plows
PARTS LIST
June 15, 2019
Lit. No. 72625, Rev. 00
1
2
4
5
34
5
3
79360 Skid Steer Attachment Plates Kit
Item Part Qty Description Item Part Qty Description
172891 1 Skid Steer Attachment Plate – Left ns 79359 1 Bolt Bag
272892 1 Skid Steer Attachment Plate – Right
79359 Bolt Bag
312 1/2-13 x 1-1/2 Hex Cap Screw G5 5 12 1/2-13 Hex Locknut GB
424 1/2 Flat Washer
ns = not shown G = Grade
79360
Lit. No. 72625, Rev. 00 2 June 15, 2019
INSTALLATION INSTRUCTIONS
Install the skid steer attachment plates to the coupler
mounting hubs on the back of the blade using a
1/2" x 1-1/2" cap screw, two 1/2" at washers, and a
1/2" locknut at each mounting hole, as shown. Tighten
fasteners to 75 ft-lb.
1/2" x 1-1/2"
Cap Screw
1/2" Flat
Washers
1/2" Flat
Washers
1/2" x 1-1/2"
Cap Screw
1/2" Locknuts
Coupler
Mounting Hub
ATTACHING SNOWPLOW TO
SKID STEER
The pusher plow skid steer attachment plates are
designed to work with the vehicle's OEM attachment
bracket.
1. Remove the bucket from the skid steer loader.
2. Position the skid steer close to the snowplow with
the mount points on the skid steer plate aligned
with the pusher plow attachment plates.
Skid Steer Plate
(Bucket removed.)
Pusher Plow
Attachment Plates
79360
Lit. No. 72625, Rev. 00 3 June 15, 2019
3. Tilt the skid steer plate forward and position the
top edge of the plate under the receiving pockets
on the attachment plates.
4. Slowly raise the arms on the skid steer and tilt the
skid steer plate toward the cab until the snowplow
mount plates are ush with the skid steer plate.
Turn the skid steer engine OFF.
5. Engage the locking levers by rotating both handles
90° to a horizontal position. The skid steer
locking levers shall insert into the snowplow lever
receiving holes.
Receiving
Pockets
Receiving
Holes
Completed Skid Steer Installation
79360
Lit. No. 72625, Rev. 00 4 June 15, 2019
Copyright © 2019 Douglas Dynamics, LLC. All rights reserved. This material may not be reproduced or copied, in whole or in part, in any
printed, mechanical, electronic, lm, or other distribution and storage media, without the written consent of the company. Authorization to
photocopy items for internal or personal use by the company's outlets or snowplow owner is granted.
The company reserves the right under its product improvement policy to change construction or design details and furnish equipment when
so altered without reference to illustrations or specications used. This equipment manufacturer or the vehicle manufacturer may require or
recommend optional equipment for snow removal. Do not exceed vehicle ratings with a snowplow. The company oers a limited warranty for
all snowplows and accessories. See separately printed page for this important information.
Printed in U.S.A.
/